For non halt-on-reset case, all cores start of simultaneously in @stext.
Master core0 proceeds with kernel boot, while other spin-wait on
@wake_flag being set by master once it is ready. So NO hardware assist
is needed for master to "kick" the others.
This patch moves this soft implementation out of mcip.c (as there is no
hardware assist) into common smp.c
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This frees up some bits to hold more high level info such as PAE being
present, w/o increasing the size of already bloated cpuinfo struct
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This is done by improving the laddering logic !
Before:
if Exception
goto excep_or_pure_k_ret
if !Interrupt(L2)
goto l1_chk
else
INTERRUPT_EPILOGUE 2
l1_chk:
if !Interrupt(L1) (i.e. pure kernel mode)
goto excep_or_pure_k_ret
else
INTERRUPT_EPILOGUE 1
excep_or_pure_k_ret:
EXCEPTION_EPILOGUE
Now:
if !Interrupt(L1 or L2) (i.e. exception or pure kernel mode)
goto excep_or_pure_k_ret
; guaranteed to be an interrupt
if !Interrupt(L2)
goto l1_ret
else
INTERRUPT_EPILOGUE 2
; by virtue of above, no need to chk for L1 active
l1_ret:
INTERRUPT_EPILOGUE 1
excep_or_pure_k_ret:
EXCEPTION_EPILOGUE
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The requirement is to
- Reenable Exceptions (AE cleared)
- Reenable Interrupts (E1/E2 set)
We need to do wiggle these bits into ERSTATUS and call RTIE.
Prev version used the pre-exception STATUS32 as starting point for what
goes into ERSTATUS. This required explicit fixups of U/DE/L bits.
Instead, use the current (in-exception) STATUS32 as starting point.
Being in exception handler U/DE/L can be safely assumed to be correct.
Only AE/E1/E2 need to be fixed.
So the new implementation is slightly better
-Avoids read form memory
-Is 4 bytes smaller for the typical 1 level of intr configuration
-Depicts the semantics more clearly
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Historically this was done by ARC IDE driver, which is long gone.
IRQ core is pretty robust now and already checks if IRQs are enabled
in hard ISRs. Thus no point in checking this in arch code, for every
call of irq enabled.
Further if some driver does do that - let it bring down the system so we
notice/fix this sooner than covering up for sucker
This makes local_irq_enable() - for L1 only case atleast simple enough
so we can inline it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Implement the TLB flush routine to evict a sepcific Super TLB entry,
vs. moving to a new ASID on every such flush.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MMUv4 in HS38x cores supports Super Pages which are basis for Linux THP
support.
Normal and Super pages can co-exist (ofcourse not overlap) in TLB with a
new bit "SZ" in TLB page desciptor to distinguish between them.
Super Page size is configurable in hardware (4K to 16M), but fixed once
RTL builds.
The exact THP size a Linx configuration will support is a function of:
- MMU page size (typical 8K, RTL fixed)
- software page walker address split between PGD:PTE:PFN (typical
11:8:13, but can be changed with 1 line)
So for above default, THP size supported is 8K * 256 = 2M
Default Page Walker is 2 levels, PGD:PTE:PFN, which in THP regime
reduces to 1 level (as PTE is folded into PGD and canonically referred
to as PMD).
Thus thp PMD accessors are implemented in terms of PTE (just like sparc)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3ze+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
copy_user_page() is needed by DAX. Without this we get a compile error
for DAX on SH:
fs/dax.c:280:2: error: implicit declaration of function `copy_user_page' [-Werror=implicit-function-declaration]
copy_user_page(vto, (void __force *)vfrom, vaddr, to);
^
This was done with a random config that happened to include DAX support.
This patch has only been compile tested.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A sporadic hang with consequent crash is observed when booting Hyper-V Gen1
guests:
Call Trace:
<IRQ>
[<ffffffff810ab68d>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff8107b616>] queue_work_on+0x46/0x90
[<ffffffff81365696>] ? add_interrupt_randomness+0x176/0x1d0
...
<EOI>
[<ffffffff81471ddb>] ? _raw_spin_unlock_irqrestore+0x3b/0x60
[<ffffffff810c295e>] __irq_put_desc_unlock+0x1e/0x40
[<ffffffff810c5c35>] irq_modify_status+0xb5/0xd0
[<ffffffff8104adbb>] mp_register_handler+0x4b/0x70
[<ffffffff8104c55a>] mp_irqdomain_alloc+0x1ea/0x2a0
[<ffffffff810c7f10>] irq_domain_alloc_irqs_recursive+0x40/0xa0
[<ffffffff810c860c>] __irq_domain_alloc_irqs+0x13c/0x2b0
[<ffffffff8104b070>] alloc_isa_irq_from_domain.isra.1+0xc0/0xe0
[<ffffffff8104bfa5>] mp_map_pin_to_irq+0x165/0x2d0
[<ffffffff8104c157>] pin_2_irq+0x47/0x80
[<ffffffff81744253>] setup_IO_APIC+0xfe/0x802
...
[<ffffffff814631c0>] ? rest_init+0x140/0x140
The issue is easily reproducible with a simple instrumentation: if
mdelay(10) is put between mp_setup_entry() and mp_register_handler() calls
in mp_irqdomain_alloc() Hyper-V guest always fails to boot when re-routing
IRQ0. The issue seems to be caused by the fact that we don't disable
interrupts while doing IOPIC programming for legacy IRQs and IRQ0 actually
happens.
Protect the setup sequence against concurrent interrupts.
[ tglx: Make the protection unconditional and not only for legacy
interrupts ]
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Link: http://lkml.kernel.org/r/1444930943-19336-1-git-send-email-vkuznets@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On 32-bit systems, the initial_page_table is reused by
efi_call_phys_prolog as an identity map to call
SetVirtualAddressMap. efi_call_phys_prolog takes care of
converting the current CPU's GDT to a physical address too.
For PAE kernels the identity mapping is achieved by aliasing the
first PDPE for the kernel memory mapping into the first PDPE
of initial_page_table. This makes the EFI stub's trick "just work".
However, for non-PAE kernels there is no guarantee that the identity
mapping in the initial_page_table extends as far as the GDT; in this
case, accesses to the GDT will cause a page fault (which quickly becomes
a triple fault). Fix this by copying the kernel mappings from
swapper_pg_dir to initial_page_table twice, both at PAGE_OFFSET and at
identity mapping.
For some reason, this is only reproducible with QEMU's dynamic translation
mode, and not for example with KVM. However, even under KVM one can clearly
see that the page table is bogus:
$ qemu-system-i386 -pflash OVMF.fd -M q35 vmlinuz0 -s -S -daemonize
$ gdb
(gdb) target remote localhost:1234
(gdb) hb *0x02858f6f
Hardware assisted breakpoint 1 at 0x2858f6f
(gdb) c
Continuing.
Breakpoint 1, 0x02858f6f in ?? ()
(gdb) monitor info registers
...
GDT= 0724e000 000000ff
IDT= fffbb000 000007ff
CR0=0005003b CR2=ff896000 CR3=032b7000 CR4=00000690
...
The page directory is sane:
(gdb) x/4wx 0x32b7000
0x32b7000: 0x03398063 0x03399063 0x0339a063 0x0339b063
(gdb) x/4wx 0x3398000
0x3398000: 0x00000163 0x00001163 0x00002163 0x00003163
(gdb) x/4wx 0x3399000
0x3399000: 0x00400003 0x00401003 0x00402003 0x00403003
but our particular page directory entry is empty:
(gdb) x/1wx 0x32b7000 + (0x724e000 >> 22) * 4
0x32b7070: 0x00000000
[ It appears that you can skate past this issue if you don't receive
any interrupts while the bogus GDT pointer is loaded, or if you avoid
reloading the segment registers in general.
Andy Lutomirski provides some additional insight:
"AFAICT it's entirely permissible for the GDTR and/or LDT
descriptor to point to unmapped memory. Any attempt to use them
(segment loads, interrupts, IRET, etc) will try to access that memory
as if the access came from CPL 0 and, if the access fails, will
generate a valid page fault with CR2 pointing into the GDT or
LDT."
Up until commit 23a0d4e8fa ("efi: Disable interrupts around EFI
calls, not in the epilog/prolog calls") interrupts were disabled
around the prolog and epilog calls, and the functional GDT was
re-installed before interrupts were re-enabled.
Which explains why no one has hit this issue until now. ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[ Updated changelog. ]
- Fix module CFLAGS setting in workaround for erratum #843419
- Update MINSIGSTKSZ and SIGSTKSZ to match glibc
- Wire up some new compat syscalls
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJWHl+mAAoJELescNyEwWM0UUEH/if7AeWriEIJD6Fdgvft4bLn
NNojsj0kq1b4m1LCydqNXiz4Vf2xdjNcuR8Ap5h3wbgG0h8rSvwXV9XDPeeZHlU/
CGPgLjrzSSsF1idw8Z37NHj0wm7yAgbsJjBI9Zrbnkm8ZExRKXUTHJCn0dUtDAc3
OYpgBgKaYqxqd4Lr+ZOw/OIkiqdvshTRrOYl2ai5yH8CvN3qdSNPanLwO5Z5hidQ
iP655RlEDUDIKZQGp5sPp8zLEdqgluuzHm5nmF1/D+7jHwJABLHD+YLuPzHk1wgn
ihk+2vN/7ok+qawaekVHliy5ySuGZMCS15YIHnSMk7K+AKP4fHYk1GOdzx0xuIA=
=hw5U
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are a few more arm64 fixes for 4.3. Again, nothing too
significant, but worth having nonetheless. The MINSIGSTKSZ update is
a bit grotty, but the value we currently have is wrong (too small), so
anybody using that will have issues already. It has Arnd's ack for
the asm-generic change.
Summary:
- Fix module CFLAGS setting in workaround for erratum #843419
- Update MINSIGSTKSZ and SIGSTKSZ to match glibc
- Wire up some new compat syscalls"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: compat: wire up new syscalls
arm64: Fix MINSIGSTKSZ and SIGSTKSZ
arm64: errata: use KBUILD_CFLAGS_MODULE for erratum #843419
While the addition of these properties is technically correct it unveils
a bug with deferred probe. The problem is that the presence of the gpio-
range property causes the gpio-tegra driver to defer probe (it needs the
pinctrl driver to be ready). That's technically correct, but it causes a
couple of issues:
- The keyboard on Chromebooks stops working. The reason for that is
that the gpio-tegra device has not registered an IRQ domain by the
time the EC SPI device is registered, hence the interrupt number
resolves to 0. This is technically a bug in the SPI core, since it
should really resolve the interrupt at probe time and defer if the
IRQ domain isn't available yet. This is similar to what's done for
I2C and platform device already.
- The gpio-tegra device deferring probe means that it is moved to the
end of the dpm_list. This list defines the suspend/resume order for
devices. However the core lacks a way to move all users of the
gpio-tegra device to the end of the dpm_list at the same time. This
in turn results in a subtle bug on Jetson TK1, where the gpio-keys
device is used to expose the power key as input. The power key is a
convenient way to wake the system from suspend. Interestingly, the
gpio-keys device ends up getting probed at a point after gpio-tegra
has been probed successfully from having been deferred earlier. As
such the driver doesn't need to defer the probe itself, and hence
the device isn't moved to the end of the dpm_list. This causes the
gpio-tegra device to be suspended before gpio-keys, which in turn
leaves gpio-keys unable to wake the system from suspend.
There are patches in the works to fix both of the above issues, but they
are too involved to make it into v4.3, so in the meantime let's fix the
regressions by commenting out the gpio-ranges properties until the fixes
have landed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Regulator fix for beagle-x15 to fix HDMI without a SD card being
inserted
- GPMC fix for showing proper timings and to allow enabling debug
options that somehow was unselectable earlier
- Add minimal documentation for new MMC1 dependency on
REGULATOR_PBIAS as it may not be obvious for people with
targeted .config files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1+r/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Fixes for omap against v4.3-rc5" from Tony Lindgren:
- Regulator fix for beagle-x15 to fix HDMI without a SD card being
inserted
- GPMC fix for showing proper timings and to allow enabling debug
options that somehow was unselectable earlier
- Add minimal documentation for new MMC1 dependency on
REGULATOR_PBIAS as it may not be obvious for people with
targeted .config files
* tag 'omap-for-v4.3/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Documentation: ARM: List new omap MMC requirements
memory: omap-gpmc: dump "before" state before first modification
memory: omap-gpmc: Fix unselectable debug option for GPMC
ARM: dts: am57xx-beagle-x15: set VDD_SD to always-on
The IRQ signal from external devices on this board is connected to
the XIRQ4 pin of the SoC. The IRQ number should be 52, not 50.
Fixes: a5e921b477 ("ARM: dts: uniphier: add ProXstream2 and PH1-LD6b SoC/board support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SHA_MAX_STATE_SIZE is just the number of u32 word for SHA512.
So replace the raw value "16" by their meaning (SHA512_DIGEST_SIZE / 4)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This commit enables standby support on Armada 385 DB-AP board, because
the PM initalization routine requires "marvell,armada380" compatible
string for all Armada 38x-based platforms.
Beside the compatible "marvell,armada38x" was wrong and should be fixed
in the stable kernels too.
[gregory.clement@free-electrons.com: add information, about the fixes]
Fixes: e5ee12817e ("ARM: mvebu: Add Armada 385 Access Point
Development Board support")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org>
The DTS erronously uses the wrong reg mapping and IRQ numbers for some
UART, WDT and timer nodes. Fix this.
Reported-by: John Wehle <john@feith.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
fix SMM emulation on Nehalem processors. The others fix some cases
that became apparent as work progressed on the firmware side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWHms0AAoJEL/70l94x66DfQkIAIpya6c/1UAthxSTqJ1wFOf8
ZKp3GCMjUjtm9k88kk6JGOlPiAvWz7CG9BVbptpkJGpgoDzquvr6ZKGG2BV88F17
MnkZCid4IBW6VeKYy7R2otkKw7+Pw8DTHRQks+VI6BN/KkeaZLzh5J8+FAl4ZaWk
YX/VulRce6SfZPYuUTRkkK8aebsopZNVG8mwWIGuBYwyH54R3KH1k/euX2joUPwm
oopzmQLgEWW7e3RsO67T36rIRgEorJLZaiiexvj1djI+e0kEEudvhJ9nC6eB52qa
oZ9nR0nkkmBmrBF8gldKDZBC+Y/ci1cJLAaoi7tdsp0wVCebPxubwbPOXxKwD8g=
=ij8Q
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes for system management mode emulation.
The first two patches fix SMM emulation on Nehalem processors. The
others fix some cases that became apparent as work progressed on the
firmware side"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix RSM into 64-bit protected mode
KVM: x86: fix previous commit for 32-bit
KVM: x86: fix SMI to halted VCPU
KVM: x86: clean up kvm_arch_vcpu_runnable
KVM: x86: map/unmap private slots in __x86_set_memory_region
KVM: x86: build kvm_userspace_memory_region in x86_set_memory_region
Some recently added code to avoid a bug introduced a build error
when CONFIG_PM is disabled and a macro is hidden:
arch/arm/mach-pxa/pxa3xx.c: In function 'pxa3xx_init':
arch/arm/mach-pxa/pxa3xx.c:439:3: error: 'NDCR' undeclared (first use in this function)
NDCR = (NDCR & ~NDCR_ND_ARB_EN) | NDCR_ND_ARB_CNTL;
^
This moves the macro outside of the #ifdef so it can be
referenced correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: adf3442cc8 ("ARM: pxa: fix DFI bus lockups on startup")
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
It includes a single fix for i.MX7D, which corrects the base address of
UART2 in device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWG7gvAAoJEFBXWFqHsHzOnysH/3g6f2HhjnyP627EgE8ipJJB
3S/rteN22cV0e8siM6oxa97gMjVGX9A6asGKkpE5v26SGKDbvhUhH5WCqKUioFCn
LDjcNUK1Yd830K/t7dyBM4bZlPp7nLCfLMzFG+8PvVWl5OvfR5eJ14KLAyS0mO9b
F/GoqV2VSrTw5AA3gOfBhckHtVZJJ01b4vu28G9NSc8eU4W5aJDQMDaZ40MLftuS
ZEt9o+us/YlJQzuIeKN2sk5Rb+w2jeZOXWEKOZfIFab3aE8BY+/NgedqMNwf1J1Z
EWGQ6oIOIe5vU6k9j0neQ4a5hVqW+layzgdXZaYhWzfkpM7DFuvVyeK08yiARts=
=h6oq
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.3, 2nd round:" from Shawn Guo:
It includes a single fix for i.MX7D, which corrects the base address of
UART2 in device tree.
* tag 'imx-fixes-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d: Fix UART2 base address
- BG2Q USB PHY compatible fix (also tagged for stable v4.2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BDI7
-----END PGP SIGNATURE-----
Merge tag 'berlin-fixes-for-4.3-1' of git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "Marvell Berlin fixes for v4.3 take 1" from Sebastian Hesselbarth:
- BG2Q USB PHY compatible fix (also tagged for stable v4.2)
* tag 'berlin-fixes-for-4.3-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: change BG2Q's USB PHY compatible
They are currently unused, and I don't think that anyone was
ever particularly happy with them. They had the unfortunate
property that they made it easy to CFI-annotate things without
thinking about them -- when pushing, do you want to just update
the CFA offset, or do you also want to update the saved location
of the register being pushed?
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447bfbd10bb268b4593b32534ecefa1f4df287e.1444696194.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway - Paul Gortmaker
* Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64 - Leif Lindholm
* Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses - Matt Fleming
* Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
* Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module - Ben Hutchings
* Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support - Taku Izumi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Oee
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into core/efi
Pull v4.4 EFI updates from Matt Fleming:
- Make the EFI System Resource Table (ESRT) driver explicitly
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway. (Paul Gortmaker)
- Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64. (Leif Lindholm)
- Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses. (Matt Fleming)
- Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
- Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module. (Ben Hutchings)
- Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support. (Taku Izumi)
Note: there is a semantic conflict between the following two commits:
8a53554e12 ("x86/efi: Fix multiple GOP device support")
ae2ee627dc ("efifb: Add support for 64-bit frame buffer addresses")
I fixed up the interaction in the merge commit, changing the type of
current_fb_base from u32 to u64.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to get into 64-bit protected mode, you need to enable
paging while EFER.LMA=1. For this to work, CS.L must be 0.
Currently, we load the segments before CR0 and CR4, which means
that if RSM returns into 64-bit protected mode CS.L is already 1
and everything breaks.
Luckily, CS.L=0 is always the case when executing RSM, because it
is forbidden to execute RSM from 64-bit protected mode. Hence it
is enough to load CR0 and CR4 first, and only then the segments.
Fixes: 660a5d517a
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
New bindings and driver have been created for STM32 series parts. This
patch integrates this changes.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When multiple GOP devices exists, but none of them implements
ConOut, the code should just choose the first GOP (according to
the comments). But currently 'fb_base' will refer to the last GOP,
while other parameters to the first GOP, which will likely
result in a garbled display.
I can reliably reproduce this bug using my ASRock Z87M Extreme4
motherboard with CSM and integrated GPU disabled, and two PCIe
video cards (NVidia GT640 and GTX980), booting from efi-stub
(booting from grub works fine). On the primary display the
ASRock logo remains and on the secondary screen it is garbled
up completely.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1444659236-24837-2-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 208473c1f3 ("ARM: wire up new syscalls") hooked up the new
userfaultfd and membarrier syscalls for ARM, so do the same for our
compat syscall table in arm64.
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are following warnings on unpatched code:
arch/x86/kernel/early_printk.c:198:32: warning: incorrect type in initializer (different address spaces)
arch/x86/kernel/early_printk.c:198:32: expected void [noderef] <asn:2>*vaddr
arch/x86/kernel/early_printk.c:198:32: got unsigned int [usertype] *<noident>
arch/x86/kernel/early_printk.c:205:32: warning: incorrect type in initializer (different address spaces)
arch/x86/kernel/early_printk.c:205:32: expected void [noderef] <asn:2>*vaddr
arch/x86/kernel/early_printk.c:205:32: got unsigned int [usertype] *<noident>
Annotate it proper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/1444646837-42615-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Fix AVX detection to prevent use of non-existent AESNI.
- Some SPARC ciphers did not set their IV size which may lead to
memory corruption"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ahash - ensure statesize is non-zero
crypto: camellia_aesni_avx - Fix CPU feature checks
crypto: sparc - initialize blkcipher.ivsize
Since we now have a generic data structure to express an
interrupt specifier, convert all hierarchical irqchips that
are OF based to use a fwnode_handle as part of their alloc
and xlate (which becomes translate) callbacks.
As most of these drivers have dependencies (they exchange IRQ
specifiers), change them all in a single, massive patch...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
An SMI to a halted VCPU must wake it up, hence a VCPU with a pending
SMI must be considered runnable.
Fixes: 64d6067057
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split the huge conditional in two functions.
Fixes: 64d6067057
Cc: stable@vger.kernel.org
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Otherwise, two copies (one of them never populated and thus bogus)
are allocated for the regular and SMM address spaces. This breaks
SMM with EPT but without unrestricted guest support, because the
SMM copy of the identity page map is all zeros.
By moving the allocation to the caller we also remove the last
vestiges of kernel-allocated memory regions (not accessible anymore
in userspace since commit b74a07beed, "KVM: Remove kernel-allocated
memory regions", 2010-06-21); that is a nice bonus.
Reported-by: Alexandre DERUMIER <aderumier@odiso.com>
Cc: stable@vger.kernel.org
Fixes: 9da0e4d5ac
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The next patch will make x86_set_memory_region fill the
userspace_addr. Since the struct is not used untouched
anymore, it makes sense to build it in x86_set_memory_region
directly; it also simplifies the callers.
Reported-by: Alexandre DERUMIER <aderumier@odiso.com>
Cc: stable@vger.kernel.org
Fixes: 9da0e4d5ac
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LDO1 regulator (VDD_SD) is connected to SoC's vddshv8. vddshv8 needs to
be kept always powered (see commit 5a0f93c657 ("ARM: dts: Add
am57xx-beagle-x15"), but at the moment VDD_SD is enabled/disabled
depending on whether an SD card is inserted or not.
This patch sets LDO1 regulator to always-on.
This patch has a side effect of fixing another issue, HDMI DDC not
working when SD card is not inserted:
Why this happens is that the tpd12s015 (HDMI level shifter/ESD
protection chip) has LS_OE GPIO input, which needs to be enabled for the
HDMI DDC to work. LS_OE comes from gpio6_28. The pin that provides
gpio6_28 is powered by vddshv8, and vddshv8 comes from VDD_SD.
So when SD card is not inserted, VDD_SD is disabled, and LS_OE stays
off.
The proper fix for the HDMI DDC issue would be to maybe have the pinctrl
framework manage the pin specific power.
Apparently this fixes also a third issue (copy paste from Kishon's
patch):
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Louis McCarthy <compeoree@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On each next iteration of for_each_compatible_node() the reference
counter for current device node is already decreased by the loop
iterator. The manual call to of_node_get() is required only on loop
break which is not happening here.
The double of_node_get() (with enabled CONFIG_OF_DYNAMIC) lead to
decreasing the counter below expected, initial value.
Fixes: fe4034a3fa ("ARM: EXYNOS: Add missing of_node_put() when parsing power domains")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
MINSIGSTKSZ and SIGSTKSZ for ARM64 are not correctly set in latest kernel.
This patch fixes this issue.
This issue is reported in LTP (testcase: sigaltstack02.c).
Testcase failed when sigaltstack() called with stack size "MINSIGSTKSZ - 1"
Since in Glibc-2.22, MINSIGSTKSZ is set to 5120 but in kernel
it is set to 2048 so testcase gets failed.
Testcase Output:
sigaltstack02 1 TPASS : stgaltstack() fails, Invalid Flag value,errno:22
sigaltstack02 2 TFAIL : sigaltstack() returned 0, expected -1,errno:12
Reported Issue in Glibc Bugzilla:
Bugfix in Glibc-2.22: [Bug 16850]
https://sourceware.org/bugzilla/show_bug.cgi?id=16850
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akhilesh Kumar <akhilesh.k@samsung.com>
Signed-off-by: Manjeet Pawar <manjeet.p@samsung.com>
Signed-off-by: Rohit Thapliyal <r.thapliyal@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit df057cc7b4 ("arm64: errata: add module build workaround for
erratum #843419") sets CFLAGS_MODULE to ensure that the large memory
model is used by the compiler when building kernel modules.
However, CFLAGS_MODULE is an environment variable and intended to be
overridden on the command line, which appears to be the case with the
Ubuntu kernel packaging system, so use KBUILD_CFLAGS_MODULE instead.
Cc: <stable@vger.kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: df057cc7b4 ("arm64: errata: add module build workaround for erratum #843419")
Reported-by: Dann Frazier <dann.frazier@canonical.com>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A certain number of patch levels of applied microcode should not
be overwritten by the microcode loader, otherwise bad things
will happen.
Check those and abort update if the current core has one of
those final patch levels applied by the BIOS. 32-bit needs
special handling, of course.
See https://bugzilla.suse.com/show_bug.cgi?id=913996 for more
info.
Tested-by: Peter Kirchgeßner <pkirchgessner@t-online.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1444641762-9437-7-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pave the way for checking the current patch level of the
microcode in a core. We want to be able to do stuff depending on
the patch level - in this case decide whether to update or not.
But that will be added in a later patch.
Drop unused local var uci assignment, while at it.
Integrate a fix for 32-bit and CONFIG_PARAVIRT from Takashi Iwai:
Use native_rdmsr() in check_current_patch_level() because with
CONFIG_PARAVIRT enabled and on 32-bit, where we run before
paging has been enabled, we cannot deref pv_info yet. Or we
could, but we'd need to access its physical address. This way of
fixing it is simpler. See:
https://bugzilla.suse.com/show_bug.cgi?id=943179 for the background.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Takashi Iwai <tiwai@suse.com>:
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1444641762-9437-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Bank 4 MCEs are logged and reported only on the node base core
(NBC) in a socket. Refer to the D18F3x44[NbMcaToMstCpuEn] field
in Fam10h and later BKDGs. The node base core (NBC) is the
lowest numbered core in the node.
This patch ensures that we inject the error on the NBC for bank
4 errors. Otherwise, triggering #MC or APIC interrupts on a core
which is not the NBC would not have any effect on the system,
i.e. we would not see any relevant output on kernel logs for the
error we just injected.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Cleanup comments. ]
[ Add a missing dependency on AMD_NB caught by Randy Dunlap. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1443190851-2172-4-git-send-email-Aravind.Gopalakrishnan@amd.com
Link: http://lkml.kernel.org/r/1444641762-9437-5-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add the capability to trigger deferred error interrupts and
threshold interrupts in order to test the APIC interrupt handler
functionality for these type of errors.
Update README section about the same too.
Reported by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Cleanup comments. ]
[ Include asm/irq_vectors.h directly so that misc randbuilds don't fail. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1443190851-2172-3-git-send-email-Aravind.Gopalakrishnan@amd.com
Link: http://lkml.kernel.org/r/1444641762-9437-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Invalid inputs such as these are currently reported in dmesg as
failing:
$> echo sweet > flags
[ 122.079139] flags_write: Invalid flags value: et
even though the 'flags' attribute has been updated correctly:
$> cat flags
sw
This is because userspace keeps writing the remaining buffer
until it encounters an error.
However, the input as a whole is wrong and we should not be
writing anything to the file. Therefore, correct flags_write()
to return -EINVAL immediately on bad input strings.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1443190851-2172-2-git-send-email-Aravind.Gopalakrishnan@amd.com
Link: http://lkml.kernel.org/r/1444641762-9437-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces new boot option named "efi_fake_mem".
By specifying this parameter, you can add arbitrary attribute
to specific memory range.
This is useful for debugging of Address Range Mirroring feature.
For example, if "efi_fake_mem=2G@4G:0x10000,2G@0x10a0000000:0x10000"
is specified, the original (firmware provided) EFI memmap will be
updated so that the specified memory regions have
EFI_MEMORY_MORE_RELIABLE attribute (0x10000):
<original>
efi: mem36: [Conventional Memory| | | | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x00000020a0000000) (129536MB)
<updated>
efi: mem36: [Conventional Memory| |MR| | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x0000000180000000) (2048MB)
efi: mem37: [Conventional Memory| | | | | | |WB|WT|WC|UC] range=[0x0000000180000000-0x00000010a0000000) (61952MB)
efi: mem38: [Conventional Memory| |MR| | | | |WB|WT|WC|UC] range=[0x00000010a0000000-0x0000001120000000) (2048MB)
efi: mem39: [Conventional Memory| | | | | | |WB|WT|WC|UC] range=[0x0000001120000000-0x00000020a0000000) (63488MB)
And you will find that the following message is output:
efi: Memory: 4096M/131455M mirrored memory
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This patch renames print_efi_memmap() to efi_print_memmap() and
make it global function so that we can invoke it outside of
arch/x86/platform/efi/efi.c
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The EFI Graphics Output Protocol uses 64-bit frame buffer addresses
but these get truncated to 32-bit by the EFI boot stub when storing
the address in the 'lfb_base' field of 'struct screen_info'.
Add a 'ext_lfb_base' field for the upper 32-bits of the frame buffer
address and set VIDEO_TYPE_CAPABILITY_64BIT_BASE when the field is
useable.
It turns out that the reason no one has required this support so far
is that there's actually code in tianocore to "downgrade" PCI
resources that have option ROMs and 64-bit BARS from 64-bit to 32-bit
to cope with legacy option ROMs that can't handle 64-bit addresses.
The upshot is that basically all GOP devices in the wild use a 32-bit
frame buffer address.
Still, it is possible to build firmware that uses a full 64-bit GOP
frame buffer address. Chad did, which led to him reporting this issue.
Add support in anticipation of GOP devices using 64-bit addresses more
widely, and so that efifb works out of the box when that happens.
Reported-by: Chad Page <chad.page@znyx.com>
Cc: Pete Hawkins <pete.hawkins@znyx.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
As we now have a common debug infrastructure between core and arm64 efi,
drop the bit of the interface passing verbose output flags around.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Now that we have an efi=debug command line option in the core code, use
this instead of the arm64-specific uefi_debug option.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
fed6cefe3b ("x86/efi: Add a "debug" option to the efi= cmdline")
adds the DBG flag, but does so for x86 only. Move this early param
parsing to core code.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Previously, UV NMI used the 'in_crash_kexec' flag to determine whether
we are in a kdump kernel or not:
5edd19af18 ("x86, UV: Make kdump avoid stack dumps")
But this flags was removed in the following commit:
9c48f1c629 ("x86, nmi: Wire up NMI handlers to new routines")
Since it isn't used any more, remove it.
Signed-off-by: Minfei Huang <mnfhuang@gmail.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: cpw@sgi.com
Cc: kexec@lists.infradead.org
Cc: mhuang@redhat.com
Link: http://lkml.kernel.org/r/1444070155-17934-1-git-send-email-mhuang@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
asm/ioctls.h contains definition for termios, not just the _IO* macros.
This error was found with a tool in development used to generate
automated pretty-printing functions for ioctl decoding in strace.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1444141657-14898-2-git-send-email-gabriel@lse.epita.fr
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have to define internally used function as static, otherwise the following
warning will be generated:
arch/x86/kernel/apic/io_apic.c:532:6: warning: no previous prototype for 'eoi_ioapic_pin' [-Wmissing-prototypes]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1444400685-98611-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following warning is issued on unfixed code.
arch/x86/platform/intel-mid/intel-mid.c:64:22: warning: symbol 'intel_mid_ops' was not declared. Should it be static?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/1444400741-98669-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The code under the label can normally be inline, without the
jumping back and forth but the latter is an optimization.
Document that.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20151009170859.GA24266@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull MIPS fixes from Ralf Baechle:
- MIPS didn't define the new ioremap_uc. Defined it as an alias for
ioremap_uncached.
- Replace workaround for MIPS16 build issue with a correct one.
* git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Define ioremap_uc
MIPS: UAPI: Ignore __arch_swab{16,32,64} when using MIPS16
Revert "MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16."
Pull swiotlb fixlet from Konrad Rzeszutek Wilk:
"Enable the SWIOTLB under 32-bit PAE kernels.
Nowadays most distros enable this due to CONFIG_HYPERVISOR|XEN=y which
select SWIOTLB. But for those that are not interested in
virtualization and wanting to use 32-bit PAE kernels and wanting to
have working DMA operations - this configures it for them"
* 'stable/for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Enable it under x86 PAE
Pull strscpy powerpc fix from Chris Metcalf.
Fix powerpc big-endian build.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/powerpc: provide zero_bytemask() for big-endian
The fixes for this week include one small patch that was years in the
making and that finally fixes using all eight CPUs on exynos542x.
The rest are lots of minor changes for sunxi, imx, exynos and shmobile
* fixing the minimum voltage for Allwinner A20
* thermal boot issue on SMDK5250.
* invalid clock used for FIMD IOMMU.
* audio on Renesas r8a7790/r8a7791
* invalid clock used for FIMD IOMMU
* LEDs on exynos5422-odroidxu3-common
* usb pin control for imx-rex
* imx53: fix PMIC interrupt level
* a Makefile typo
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IsHY
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"The fixes for this week include one small patch that was years in the
making and that finally fixes using all eight CPUs on exynos542x.
The rest are lots of minor changes for sunxi, imx, exynos and shmobile
- fixing the minimum voltage for Allwinner A20
- thermal boot issue on SMDK5250.
- invalid clock used for FIMD IOMMU.
- audio on Renesas r8a7790/r8a7791
- invalid clock used for FIMD IOMMU
- LEDs on exynos5422-odroidxu3-common
- usb pin control for imx-rex
- imx53: fix PMIC interrupt level
- a Makefile typo"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: Fix wrong clock binding for sysmmu_fimd1_1 on exynos5420
ARM: dts: Fix bootup thermal issue on smdk5250
ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain for sound
ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain for sound
arm-cci500: Don't enable PMU driver by default
ARM: dts: fix usb pin control for imx-rex dts
ARM: imx53: qsrb: fix PMIC interrupt level
ARM: imx53: include IRQ dt-bindings header
ARM: dts: add suspend opp to exynos4412
ARM: dts: Fix LEDs on exynos5422-odroidxu3
ARM: EXYNOS: reset Little cores when cpu is up
ARM: dts: Fix Makefile target for sun4i-a10-itead-iteaduino-plus
ARM: dts: sunxi: Raise minimum CPU voltage for sun7i-a20 to meet SoC specifications
Hardware virtualisation of GICv3 is only supported by 64bit hosts for
the moment. Some VGICv3 bits are missing from the 32bit side, and this
patch allows to still be able to build 32bit hosts when CONFIG_ARM_GIC_V3
is selected.
To this end, we introduce a new option, CONFIG_KVM_ARM_VGIC_V3, that is
only enabled on the 64bit side. The selection is done unconditionally
because CONFIG_ARM_GIC_V3 is always enabled on arm64.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch allows ARM guests to use GICv3 on an arm64 host
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Implement the system and memory-mapped register accesses in
asm/arch_gicv3.h for 32bit architectures.
This patch is a straightforward translation of the arm64 header. 64bit
accesses are done in two times and don't need atomicity: TYPER is
read-only, and the upper-word of IROUTER is always zero on 32bit
architectures.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On 32bit platforms, we cannot assure that an I/O ldrd or strd will be
done atomically. Besides, an hypervisor would be unable to emulate such
accesses.
In order to allow the AArch32 version of the driver to split them into
two 32bit accesses while keeping the requirement for atomic writes, this
patch specializes the IROUTER and TYPER accesses.
Since the latter is an ID register, it won't need to be read atomically,
but we still avoid future confusion by using gic_read_typer instead of a
generic gic_readq.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch does a few simple compatibility-related changes:
- change the system register access prototypes to their actual size,
- homogenise mpidr accesses with unsigned long,
- force the 64bit register values to unsigned long long.
Note: the list registers are 64bit on GICv3, but the AArch32 vGIC driver
will need to split their values into two 32bit registers: LRn and LRCn.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch moves the GICv3 system register access helpers to
arch/arm64/. Their 32bit counterparts will need to use mrc/mcr accesses
instead of mrs_s/msr_s.
[maz: fixed conflict with Cavium erratum handling]
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As the firmware (or the hypervisor) may have disabled SRE access,
check that SRE can actually be enabled before declaring that we
do have that capability.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Contrary to what was originally expected, EL3 firmware can (for whatever
reason) disable GICv3 system register access. In this case, the kernel
explodes very early.
Work around this by testing if the SRE bit sticks or not. If it doesn't,
abort the GICv3 setup, and pray that the firmware has passed a DT that
doesn't contain a GICv3 node.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since support for half-word atomic exchange was not there and Qspinlock
on ARM requires it, modified __xchg() to add support for that as well.
ARMv6 and lower does not support ldrex{b,h} so, added a guard code to
prevent build breaks.
Signed-off-by: Sarbojit Ganguly <ganguly.s@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename feat_c3stop to twd_features to match the other variables in this
file. Initialise it with the standard features that we always support,
and arrange to set the CLOCK_EVT_FEAT_C3STOP when appropriate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In 5388a6b266 ("ARM: SMP: Always enable clock event broadcast support")
Russell noted that "the TWD local timers are unable to wake up the CPU
when it is placed into a low power mode".
However, some platforms do not stop the TWD block in low-power mode,
and can thus use the TWD timer in one-shot mode, without setting up
a broadcast device.
Make the driver check for the "always-on" boolean property, and set
the CLOCK_EVT_FEAT_C3STOP flag accordingly.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARC is the only arch with unsigned long type (vs. struct page *).
Historically this was done to avoid the page_address() calls in various
arch hooks which need to get the virtual/logical address of the table.
Some arches alternately define it as pte_t *, and is as efficient as
unsigned long (generated code doesn't change)
Suggested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
GCC is unable to properly optimize functions that have a very
short likely case and a longer and register-heavier cold part --
it fails to sink all of the register saving and stack frame
setup code into the unlikely part.
Help it out with syscall_return_slowpath() by splitting it into
two parts and inline the hot part.
Saves 6 cycles for compat syscalls.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/0f773a894ab15c589ac794c2d34ca6ba9b5335c9.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
GCC is unable to properly optimize functions that have a very
short likely case and a longer and register-heavier cold part --
it fails to sink all of the register saving and stack frame
setup code into the unlikely part.
Help it out with prepare_exit_to_usermode() by splitting it into
two parts and inline the hot part.
Saves 6-8 cycles for compat syscalls.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/9fc53eda4a5b924070952f12fa4ae3e477640a07.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This shaves a few cycles off the slow paths.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/ce383fa9e129286ce6da6e00b53acd4c9fb5d06a.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We're following a 32-bit pointer, and the uaccess code isn't
smart enough to figure out that the access_ok() check isn't
needed.
This saves about three cycles on a cache-hot fast syscall.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/bdff034e2f23c5eb974c760cf494cb5bddce8f29.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On systems that support fast syscalls, we only really care about
the performance of the fast syscall path. Forcibly inline it
and add a likely annotation.
This saves 4-6 cycles.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/8472036ff1f4b426b4c4c3e3d0b3bf5264407c0c.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These checks are quite slow. Disable them in non-lockdep
kernels to reduce the performance hit.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/eccff2a154ae6fb50f40228901003a6e9c24f3d0.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is slightly messy, but it eliminates an unnecessary cli;sti
pair.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/22f34b1096694a37326f36c53407b8dd90f37948.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It's no longer needed.
We could reinstate something like it as an optimization, which
would remove two cachelines from the fast syscall entry working
set. I benchmarked it, and it makes no difference whatsoever to
the performance of cache-hot compat syscalls on Sandy Bridge.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/f08cc0cff30201afe9bb565c47134c0a6c1a96a2.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
syscall_exit is going away, and return tracing is just a
function call now, so open-code the two non-syscall 32-bit
users.
While we're at it, update the big register layout comment.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/a6b3c472fda7cda0e368c3ccd553dea7447dfdd2.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If CS, SS and IP are as expected and FLAGS is compatible with
SYSRETL, then return from fast compat syscalls (both SYSCALL and
SYSENTER) using SYSRETL.
Unlike native 64-bit opportunistic SYSRET, this is not invisible
to user code: RCX and R8-R15 end up in a different state than
shown saved in pt_regs. To compensate, we only do this when
returning to the vDSO fast syscall return path. This won't
interfere with syscall restart, as we won't use SYSRETL when
returning to the INT80 restart instruction.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/aa15e49db33773eb10b73d73466b6d5466d7856a.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
What, you didn't realize that SYSENTER and SYSCALL were actually
the same thing? :)
Unlike the old code, this actually passes the ptrace_syscall_32
test on AMD systems.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/b74615af58d785aa02d917213ec64e2022a2c796.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This handles both SYSENTER and SYSCALL. The asm glue will take
care of the differences.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/6041a58a9b8ef6d2522ab4350deb1a1945eb563f.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
System calls are really quite simple. Add a helper to call
a 32-bit system call.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/a77ed179834c27da436fb4a7fb23c8ee77abc11c.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Syscalls are asmlinkage functions (on 32-bit kernels), take six
args of type unsigned long, and return long. Note that uml
could probably be slightly cleaned up on top of this patch.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/4d3ecc4a169388d47009175408b2961961744e6f.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The header was missing some compat declarations.
Also make sys_call_ptr_t have a consistent type.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/3166aaff0fb43897998fcb6ef92991533f8c5c6c.1444091585.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is conceptually simpler. More importantly, it eliminates
the PTREGSCALL and execve stubs, which were not compatible with
the C ABI. This means that C code can call through the compat
syscall table.
The execve stubs are a bit subtle. They did two things: they
cleared some registers and they forced slow-path return.
Neither is necessary any more: elf_common_init clears the extra
registers and start_thread calls force_iret().
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/f95b7f7dfaacf88a8cae85bb06226cae53769287.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We now have only one code path that calls through the compat
syscall table. This will make it much more pleasant to change
the pt_regs vs register calling convention, which we need to do
to move the call into C.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/320cda5573cefdc601b955d23fbe8f36c085432d.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These audit optimizations are messy and hard to maintain. We'll
get a similar effect from opportunistic sysret when fast compat
system calls are re-implemented.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/0bcca79ac7ff835d0e5a38725298865b01347a82.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We've disabled the vDSO helpers to call them, so turn off the
entries entirely (temporarily) in preparation for cleaning them
up.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/8d6e84bf651519289dc532dcc230adfabbd2a3eb.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The goal is to integrate the SYSENTER and SYSCALL32 entry paths
with the INT80 path. SYSENTER clobbers ESP and EIP. SYSCALL32
clobbers ECX (and, invisibly, R11). SYSRETL (long mode to
compat mode) clobbers ECX and, invisibly, R11. SYSEXIT (which
we only need for native 32-bit) clobbers ECX and EDX.
This means that we'll need to provide ESP to the kernel in a
register (I chose ECX, since it's only needed for SYSENTER) and
we need to provide the args that normally live in ECX and EDX in
memory.
The epilogue needs to restore ECX and EDX, since user code
relies on regs being preserved.
We don't need to do anything special about EIP, since the kernel
already knows where we are. The kernel will eventually need to
know where int $0x80 lands, so add a vdso_image entry for it.
The only user-visible effect of this code is that ptrace-induced
changes to ECX and EDX during fast syscalls will be lost. This
is already the case for the SYSENTER path.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/b860925adbee2d2627a0671fbfe23a7fd04127f8.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Before we start calling execve in contexts that honor the full
pt_regs, we need to teach it to initialize all registers.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/65a38a9edee61a1158cfd230800c61dbd963dac5.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Maintaining the current CFI annotations written in R'lyehian is
difficult for most of us. Translate them to something a little
closer to English.
This will remove the CFI data for kernels built with extremely
old versions of binutils. I think this is a fair tradeoff for
the ability for mortals to edit the asm.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/ae3ff4ff5278b4bfc1e1dab368823469866d4b71.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For the vDSO, user code wants runtime unwind info. Make sure
that, if we use .cfi directives, we generate it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/16e29ad8855e6508197000d8c41f56adb00d7580.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
131484c8da ("x86/debug: Remove perpetually broken, unmaintainable dwarf annotations")
removed all the manual DWARF annotations outside the vDSO. It also removed
the macros we used for the manual annotations.
Re-add these macros so that we can clean up the vDSO annotations.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/4c70bb98a8b773c8ccfaabf6745e569ff43e7f65.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All unrecovered machine check errors on PowerNV should cause an
immediate panic. There are 2 reasons that this is the right policy:
it's not safe to continue, and we're already trying to reboot.
Firstly, if we go through the recovery process and do not successfully
recover, we can't be sure about the state of the machine, and it is
not safe to recover and proceed.
Linux knows about the following sources of Machine Check Errors:
- Uncorrectable Errors (UE)
- Effective - Real Address Translation (ERAT)
- Segment Lookaside Buffer (SLB)
- Translation Lookaside Buffer (TLB)
- Unknown/Unrecognised
In the SLB, TLB and ERAT cases, we can further categorise these as
parity errors, multihit errors or unknown/unrecognised.
We can handle SLB errors by flushing and reloading the SLB. We can
handle TLB and ERAT multihit errors by flushing the TLB. (It appears
we may not handle TLB and ERAT parity errors: I will investigate
further and send a followup patch if appropriate.)
This leaves us with uncorrectable errors. Uncorrectable errors are
usually the result of ECC memory detecting an error that it cannot
correct, but they also crop up in the context of PCI cards failing
during DMA writes, and during CAPI error events.
There are several types of UE, and there are 3 places a UE can occur:
Skiboot, the kernel, and userspace. For Skiboot errors, we have the
facility to make some recoverable. For userspace, we can simply kill
(SIGBUS) the affected process. We have no meaningful way to deal with
UEs in kernel space or in unrecoverable sections of Skiboot.
Currently, these unrecovered UEs fall through to
machine_check_expection() in traps.c, which calls die(), which OOPSes
and sends SIGBUS to the process. This sometimes allows us to stumble
onwards. For example we've seen UEs kill the kernel eehd and
khugepaged. However, the process killed could have held a lock, or it
could have been a more important process, etc: we can no longer make
any assertions about the state of the machine. Similarly if we see a
UE in skiboot (and again we've seen this happen), we're not in a
position where we can make any assertions about the state of the
machine.
Likewise, for unknown or unrecognised errors, we're not able to say
anything about the state of the machine.
Therefore, if we have an unrecovered MCE, the most appropriate thing
to do is to panic.
The second reason is that since e784b6499d ("powerpc/powernv: Invoke
opal_cec_reboot2() on unrecoverable machine check errors."), we
attempt a special OPAL reboot on an unhandled MCE. This is so the
hardware can record error data for later debugging.
The comments in that commit assert that we are heading down the panic
path anyway. At the moment this is not always true. With UEs in kernel
space, for instance, they are marked as recoverable by the hardware,
so if the attempt to reboot failed (e.g. old Skiboot), we wouldn't
panic() but would simply die() and OOPS. It doesn't make sense to be
staggering on if we've just tried to reboot: we should panic().
Explicitly panic() on unrecovered MCEs on PowerNV.
Update the comments appropriately.
This fixes some hangs following EEH events on cxlflash setups.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
native_hpte_clear() is called in real mode from two places:
- Early in boot during htab initialisation if firmware assisted dump is
active.
- Late in the kexec path.
In both contexts there is no need to disable interrupts are they are
already disabled. Furthermore, locking around the tlbie() is only required
for pre POWER5 hardware.
On POWER5 or newer hardware concurrent tlbie()s work as expected and on pre
POWER5 hardware concurrent tlbie()s could result in deadlock. This code
would only be executed at crashdump time, during which all bets are off,
concurrent tlbie()s are unlikely and taking locks is unsafe therefore the
best course of action is to simply do nothing. Concurrent tlbie()s are not
possible in the first case as secondary CPUs have not come up yet.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For some reason, only the little-endian flavor of
powerpc provided the zero_bytemask() implementation.
Reported-by: Michal Sojka <sojkam1@fel.cvut.cz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
We need to explicitly check the AVX and AES CPU features, as we can't
infer them from the related XSAVE feature flags. For example, the
Core i3 2310M passes the XSAVE feature test but does not implement
AES-NI.
Reported-and-tested-by: Stéphane Glondu <glondu@debian.org>
References: https://bugs.debian.org/800934
Fixes: ce4f5f9b65 ("x86/fpu, crypto x86/camellia_aesni_avx: Simplify...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org> # 4.2
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some of the crypto algorithms write to the initialization vector,
but no space has been allocated for it. This clobbers adjacent memory.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most distributions end up enabling SWIOTLB already with 32-bit
kernels due to the combination of CONFIG_HYPERVISOR_GUEST|CONFIG_XEN=y
as those end up requiring the SWIOTLB.
However for those that are not interested in virtualization and
run in 32-bit they will discover that: "32-bit PAE 4.2.0 kernel
(no IOMMU code) would hang when writing to my USB disk. The kernel
spews million(-ish messages per sec) to syslog, effectively
"hanging" userspace with my kernel.
Oct 2 14:33:06 voodoochild kernel: [ 223.287447] nommu_map_sg:
overflow 25dcac000+1024 of device mask ffffffff
Oct 2 14:33:06 voodoochild kernel: [ 223.287448] nommu_map_sg:
overflow 25dcac000+1024 of device mask ffffffff
Oct 2 14:33:06 voodoochild kernel: [ 223.287449] nommu_map_sg:
overflow 25dcac000+1024 of device mask ffffffff
... etc ..."
Enabling it makes the problem go away.
N.B. With a6dfa128ce
"config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected"
we also have the important part of the SG macros enabled to make this
work properly - in case anybody wants to backport this patch.
Reported-and-Tested-by: Christian Melki <christian.melki@t2data.com>
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- A couple of locking fixes for RT kernels
- Avoid printing bogus initrd warnings when initrd isn't present
- Performance fix for random mmap file readahead
- Typo fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJWFO+aAAoJELescNyEwWM0z14IALpleyenZXl+xqxMjNyOXouG
/2SbTZH7iD/vnfCL6G7/Poq00I2ghtBSRFGXajfg7V0mjH1HTfVXVN19IXaUUwjW
IfAMqSyC43dDBdsGn3A1ZqPRNk+chxjwz7zimGqPowuM87C4aj/sqetBSnuybZtB
lSYfCFGpDj8cpsJ0xwYYhuq8xUgixQMslTj+rVAFtfsLkDHUu175l+vP7t2xOv5v
bmyPlz15O/v9febnLYFVFPWZB2IWfvaFkR30qUGsMe6BGWdGDe/RGUPksZDLlPdL
Yj4AKq+9Bx0lPvO+vNEqfvScKdVjMpttVEMfi2cQ8kUbD1rRPZ7ZTHsfcEOuB1w=
=Zi+I
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"This addresses a couple of issues found with RT, a broken initrd
message in the console log and a simple performance fix for some MMC
workloads.
Summary:
- A couple of locking fixes for RT kernels
- Avoid printing bogus initrd warnings when initrd isn't present
- Performance fix for random mmap file readahead
- Typo fix"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: replace read_lock to rcu lock in call_break_hook
arm64: Don't relocate non-existent initrd
arm64: convert patch_lock to raw lock
arm64: readahead: fault retry breaks mmap file read random detection
arm64: debug: Fix typo in debug-monitors.c
Enable the "wake-on-filer" (aka. wake on user defined packet)
wake on lan capability for the eTSEC ethernet nodes.
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
32-bit userspace will now always see the same vDSO, which is
exactly what used to be the int80 vDSO. Subsequent patches will
clean it up and make it support SYSENTER and SYSCALL using
alternatives.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/e7e6b3526fa442502e6125fe69486aab50813c32.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We eventually want to make it all the way into C code before
enabling interrupts. We need to rework our flags handling
slightly to delay enabling interrupts.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/35d24d2a9305da3182eab7b2cdfd32902e90962c.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rather than worrying about exactly where LOCKDEP_SYS_EXIT should
go in the asm code, add it to prepare_exit_from_usermode() and
remove all of the asm calls that are followed by
prepare_exit_to_usermode().
LOCKDEP_SYS_EXIT now appears only in the syscall fast paths.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1736ebe948b845e68120b86b89091f3ec27f5e8e.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Clearing NT is part of the prologue, whereas loading up arg6
makes more sense to think about as part of syscall processing.
Reorder them.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/19eb235828b2d2a52c53459e09f2974e15e65a35.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This should improve code quality a bit. It also shrinks the kernel text:
Before:
text data bss dec filename
21828379 5194760 1277952 28301091 vmlinux
After:
text data bss dec filename
21827997 5194760 1277952 28300709 vmlinux
... by 382 bytes.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/f427b8002d932e5deab9055e0074bb4e7e80ee39.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
GCC doesn't realize that get_user(), put_user(), and their __
variants are unlikely to fail. Tell it.
I noticed this while playing with the C entry code.
Before:
text data bss dec filename
21828763 5194760 1277952 28301475 vmlinux.baseline
After:
text data bss dec filename
21828379 5194760 1277952 28301091 vmlinux.new
The generated code shrunk by 384 bytes.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/dc37bed7024319c3004d950d57151fca6aeacf97.1444091584.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull strscpy fixes from Chris Metcalf :
"This patch series fixes up a couple of architecture issues where
strscpy wasn't configured correctly (missing on h8300, duplicating
local and asm-generic copies on powerpc and tile).
It also adds a use of zero_bytemask() to the final store for strscpy
to avoid writing uninitialized data to the destination. However, to
make this work we had to add support for zero_bytemask() to the two
architectures that didn't have it (alpha and tile), because they were
providing their own local copies, but didn't provide the
zero_bytemask() that was previously only required when building with
CONFIG_DCACHE_WORD_ACCESS"
[ Side note: there is still no actual users of strscpy except for the
one preexisting use in arch/tile that predates the generic version.
So this is all about fixing the infrastructure so that we eventually
can start using it. - Linus ]
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
strscpy: zero any trailing garbage bytes in the destination
word-at-a-time.h: support zero_bytemask() on alpha and tile
word-at-a-time.h: fix some Kbuild files
arch/tile added word-at-a-time.h after the patch that added generic-y
entries; the generic-y entry is now stale.
arch/h8300 is newer than the generic-y patch for word-at-a-time.h,
and needs a generic-y entry.
arch/powerpc seems to have gotten a generic-y entry by mistake in
the first patch; this change removes it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
When booting a kernel without an initrd, the kernel reports that it
moves -1 bytes worth, having gone through the motions with initrd_start
equal to initrd_end:
Moving initrd from [4080000000-407fffffff] to [9fff49000-9fff48fff]
Prevent this by bailing out early when the initrd size is zero (i.e. we
have no initrd), avoiding the confusing message and other associated
work.
Fixes: 1570f0d7ab ("arm64: support initrd outside kernel linear map")
Cc: Mark Salter <msalter@redhat.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In multi-segment system, uncore devices may belong to buses whose segment
number is other than 0:
....
0000:ff:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03)
...
0001:7f:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03)
...
0001:bf:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03)
...
0001:ff:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03
...
In that case, relation of bus number and physical id may be broken
because "uncore_pcibus_to_physid" doesn't take account of PCI segment.
For example, bus 0000:ff and 0001:ff uses the same entry of
"uncore_pcibus_to_physid" array.
This patch fixes this problem by introducing the segment-aware pci2phy_map instead.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: hpa@zytor.com
Link: http://lkml.kernel.org/r/1443096621-4119-1-git-send-email-izumi.taku@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds new PMUs to support cstate related free running
(read-only) counters. These counters may be used simultaneously by other
tools, such as turbostat. However, it still make sense to implement them
in perf. Because we can conveniently collect them together with other
events, and allow to use them from tools without special MSR access
code.
These counters include CORE_C*_RESIDENCY and PKG_C*_RESIDENCY.
According to counters' scope and category, two PMUs are registered with
the perf_event core subsystem.
- 'cstate_core': The counter is available for each physical core. The
counters include CORE_C*_RESIDENCY.
- 'cstate_pkg': The counter is available for each physical package. The
counters include PKG_C*_RESIDENCY.
The events are exposed in sysfs for use by perf stat and other tools.
The files are:
/sys/devices/cstate_core/events/c*-residency
/sys/devices/cstate_pkg/events/c*-residency
These events only support system-wide mode counting.
The /sys/devices/cstate_*/cpumask file can be used by tools to figure
out which CPUs to monitor by default.
The PMU type (attr->type) is dynamically allocated and is available from
/sys/devices/core_misc/type and /sys/device/cstate_*/type.
Sampling is not supported.
Here is an example.
- To caculate the fraction of time when the core is running in C6 state
CORE_C6_time% = CORE_C6_RESIDENCY / TSC
# perf stat -x, -e"cstate_core/c6-residency/,msr/tsc/" -C0 -- taskset -c 0 sleep 5
11838820015,,cstate_core/c6-residency/,5175919658,100.00
11877130740,,msr/tsc/,5175922010,100.00
For sleep, 99.7% of time we ran in C6 state.
# perf stat -x, -e"cstate_core/c6-residency/,msr/tsc/" -C0 -- taskset -c 0 busyloop
1253316,,cstate_core/c6-residency/,4360969154,100.00
10012635248,,msr/tsc/,4360972366,100.00
For busyloop, 0.01% of time we ran in C6 state.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1443443404-8581-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the introduction of the context switch preempt_count invariant,
and the demise of PREEMPT_ACTIVE, its pointless to save/restore the
per-cpu preemption count, it must always be 2.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Assuming units of PREEMPT_DISABLE_OFFSET for preempt_count() numbers.
Now that TASK_DEAD no longer results in preempt_count() == 3 during
scheduling, we will always call context_switch() with preempt_count()
== 2.
However, we don't always end up with preempt_count() == 2 in
finish_task_switch() because new tasks get created with
preempt_count() == 1.
Create FORK_PREEMPT_COUNT and set it to 2 and use that in the right
places. Note that we cannot use INIT_PREEMPT_COUNT as that serves
another purpose (boot).
After this, preempt_count() is invariant across the context switch,
with exception of PREEMPT_ACTIVE.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
DSA expects the host_dev pointer to be the device structure associated
with the MDIO bus controller driver. First commit breaking that was
c3a07134e6 ("mv643xx_eth: convert to use the Marvell Orion MDIO
driver"), and then, it got completely under the radar for a while.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu>
Fixes: c3a07134e6 ("mv643xx_eth: convert to use the Marvell Orion MDIO driver")
CC: stable@vger.kernel.org
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- Fix VM save performance regression with x86 PV guests.
- Make kexec work in x86 PVHVM guests (if Xen has the soft-reset ABI).
- Other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWE8wQAAoJEFxbo/MsZsTRVTMH/0eqSg2M78wv4sBl234Y3FE9
AN8KFUdlkK7VN9v0uuLMDSKIWNUuFJIvo/2rElWGRiX2Q+/pfnQg3ZSFhub9S8uL
T4LCvmG9viRFb2oUz792ewqncSw3X98Jpto4smA820gJRjndBSWm5HUKUtPAkv1M
l5DFMEgOeHbu+wCbKD/ZPEt5K9GsIaNviSNoWtYHirZwrd00oLmNbWp+g8lIGQiT
3vLW0SaZzjL6akKxihb/p3WZ9eNmyz8yk0V7dItUEVUB9qoaDDLJ5qIRSHHWTWQD
Jza/GE32VallZLuEXGG5/D86MsnyVYHC+lZtwo2IptOGm8v7WuZRv094wI1ev5c=
=aiDw
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.3b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix VM save performance regression with x86 PV guests
- Make kexec work in x86 PVHVM guests (if Xen has the soft-reset ABI)
- Other minor fixes.
* tag 'for-linus-4.3b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen/p2m: hint at the last populated P2M entry
x86/xen: Do not clip xen_e820_map to xen_e820_map_entries when sanitizing map
x86/xen: Support kexec/kdump in HVM guests by doing a soft reset
xen/x86: Don't try to write syscall-related MSRs for PV guests
xen: use correct type for HYPERVISOR_memory_op()
Pull s390 fixes from Martin Schwidefsky:
"Three bug fixes and an update to the default configuration"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/defconfig: set SCSI_DH=y
s390/vtime: correct scaled cputime of partially idle CPUs
s390/boot/decompression: disable floating point in decompressor
s390/numa: use correct type for node_to_cpumask_map
With commit 633d6f17cd (x86/xen: prepare
p2m list for memory hotplug) the P2M may be sized to accomdate a much
larger amount of memory than the domain currently has.
When saving a domain, the toolstack must scan all the P2M looking for
populated pages. This results in a performance regression due to the
unnecessary scanning.
Instead of reporting (via shared_info) the maximum possible size of
the P2M, hint at the last PFN which might be populated. This hint is
increased as new leaves are added to the P2M (in the expectation that
they will be used for populated entries).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: <stable@vger.kernel.org> # 4.0+
* Add Add CPG/MSTP Clock Domain for sound on r8a779[01] SoCs.
This allows sound to work once again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0wuy
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.3" from Simon Horman
* Add Add CPG/MSTP Clock Domain for sound on r8a779[01] SoCs.
This allows sound to work once again.
* tag 'renesas-fixes-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain for sound
ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain for sound
Two patches, one that fixes one of the DT build, and the other raising the
voltage of the lowest OPP of the A20 to remain within the SoC operating
boundaries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4XBA
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.3" from Maxime Ripard:
Two patches, one that fixes one of the DT build, and the other raising the
voltage of the lowest OPP of the A20 to remain within the SoC operating
boundaries
* tag 'sunxi-fixes-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: Fix Makefile target for sun4i-a10-itead-iteaduino-plus
ARM: dts: sunxi: Raise minimum CPU voltage for sun7i-a20 to meet SoC specifications
- fix invalid clock used for FIMD IOMMU
- fix thermal boot issue smdk5250-smdk5250
- fix S2R on exynos4412 trats2 boards
- fix LEDs on exynos5422-odroidxu3-common
- fix booting of all 8 cores on exynos542x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lpRb
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v4.3" from Kukjin Kim:
- fix invalid clock used for FIMD IOMMU
- fix thermal boot issue smdk5250-smdk5250
- fix S2R on exynos4412 trats2 boards
- fix LEDs on exynos5422-odroidxu3-common
- fix booting of all 8 cores on exynos542x
* tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fix wrong clock binding for sysmmu_fimd1_1 on exynos5420
ARM: dts: Fix bootup thermal issue on smdk5250
ARM: dts: add suspend opp to exynos4412
ARM: dts: Fix LEDs on exynos5422-odroidxu3
ARM: EXYNOS: reset Little cores when cpu is up
All architectures must now define ioremap_uc(), but MIPS currently
only has ioremap_nocache().
Fixes: 4c73e89266 ("arch/*/io.h: Add ioremap_uc() to all architectures")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11263/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Warn on any residual W+X mappings after setting NX
if DEBUG_WX is enabled. Introduce a separate
X86_PTDUMP_CORE config that enables the code for
dumping the page tables without enabling the debugfs
interface, so that DEBUG_WX can be enabled without
exposing the debugfs interface. Switch EFI_PGT_DUMP
to using X86_PTDUMP_CORE so that it also does not require
enabling the debugfs interface.
On success it prints this to the kernel log:
x86/mm: Checked W+X mappings: passed, no W+X pages found.
On failure it prints a warning and a count of the failed pages:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at arch/x86/mm/dump_pagetables.c:226 note_page+0x610/0x7b0()
x86/mm: Found insecure W+X mapping at address ffffffff81755000/__stop___ex_table+0xfa8/0xabfa8
[...]
Call Trace:
[<ffffffff81380a5f>] dump_stack+0x44/0x55
[<ffffffff8109d3f2>] warn_slowpath_common+0x82/0xc0
[<ffffffff8109d48c>] warn_slowpath_fmt+0x5c/0x80
[<ffffffff8106cfc9>] ? note_page+0x5c9/0x7b0
[<ffffffff8106d010>] note_page+0x610/0x7b0
[<ffffffff8106d409>] ptdump_walk_pgd_level_core+0x259/0x3c0
[<ffffffff8106d5a7>] ptdump_walk_pgd_level_checkwx+0x17/0x20
[<ffffffff81063905>] mark_rodata_ro+0xf5/0x100
[<ffffffff817415a0>] ? rest_init+0x80/0x80
[<ffffffff817415bd>] kernel_init+0x1d/0xe0
[<ffffffff8174cd1f>] ret_from_fork+0x3f/0x70
[<ffffffff817415a0>] ? rest_init+0x80/0x80
---[ end trace a1f23a1e42a2ac76 ]---
x86/mm: Checked W+X mappings: FAILED, 171 W+X pages found.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1444064120-11450-1-git-send-email-sds@tycho.nsa.gov
[ Improved the Kconfig help text and made the new option default-y
if CONFIG_DEBUG_RODATA=y, because it already found buggy mappings,
so we really want people to have this on by default. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When running kprobe test on arm64 rt kernel, it reports the below warning:
root@qemu7:~# modprobe kprobe_example
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 0, irqs_disabled(): 128, pid: 484, name: modprobe
CPU: 0 PID: 484 Comm: modprobe Not tainted 4.1.6-rt5 #2
Hardware name: linux,dummy-virt (DT)
Call trace:
[<ffffffc0000891b8>] dump_backtrace+0x0/0x128
[<ffffffc000089300>] show_stack+0x20/0x30
[<ffffffc00061dae8>] dump_stack+0x1c/0x28
[<ffffffc0000bbad0>] ___might_sleep+0x120/0x198
[<ffffffc0006223e8>] rt_spin_lock+0x28/0x40
[<ffffffc000622b30>] __aarch64_insn_write+0x28/0x78
[<ffffffc000622e48>] aarch64_insn_patch_text_nosync+0x18/0x48
[<ffffffc000622ee8>] aarch64_insn_patch_text_cb+0x70/0xa0
[<ffffffc000622f40>] aarch64_insn_patch_text_sync+0x28/0x48
[<ffffffc0006236e0>] arch_arm_kprobe+0x38/0x48
[<ffffffc00010e6f4>] arm_kprobe+0x34/0x50
[<ffffffc000110374>] register_kprobe+0x4cc/0x5b8
[<ffffffbffc002038>] kprobe_init+0x38/0x7c [kprobe_example]
[<ffffffc000084240>] do_one_initcall+0x90/0x1b0
[<ffffffc00061c498>] do_init_module+0x6c/0x1cc
[<ffffffc0000fd0c0>] load_module+0x17f8/0x1db0
[<ffffffc0000fd8cc>] SyS_finit_module+0xb4/0xc8
Convert patch_lock to raw loc kto avoid this issue.
Although the problem is found on rt kernel, the fix should be applicable to
mainline kernel too.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is the arm64 portion of commit 45cac65b0f ("readahead: fault
retry breaks mmap file read random detection"), which was absent from
the initial port and has since gone unnoticed. The original commit says:
> .fault now can retry. The retry can break state machine of .fault. In
> filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
> try, since the page is in page cache now, ra->mmap_miss is decreased. And
> these are done in one fault, so we can't detect random mmap file access.
>
> Add a new flag to indicate .fault is tried once. In the second try, skip
> ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
With this change, Mark reports that:
> Random read improves by 250%, sequential read improves by 40%, and
> random write by 400% to an eMMC device with dm crypto wrapped around it.
Cc: Shaohua Li <shli@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Riley Andrews <riandrews@android.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For ARMv7 with UDIV instruction support, generate an UDIV instruction
followed by an MLS instruction.
For other ARM variants, generate code calling a C wrapper similar to
the jit_udiv() function used for BPF_ALU | BPF_DIV instructions.
Some performance numbers reported by the test_bpf module (the duration
per filter run is reported in nanoseconds, between "jitted:<x>" and
"PASS":
ARMv7 QEMU nojit: test_bpf: #3 DIV_MOD_KX jited:0 2196 PASS
ARMv7 QEMU jit: test_bpf: #3 DIV_MOD_KX jited:1 104 PASS
ARMv5 QEMU nojit: test_bpf: #3 DIV_MOD_KX jited:0 2176 PASS
ARMv5 QEMU jit: test_bpf: #3 DIV_MOD_KX jited:1 1104 PASS
ARMv5 kirkwood nojit: test_bpf: #3 DIV_MOD_KX jited:0 1103 PASS
ARMv5 kirkwood jit: test_bpf: #3 DIV_MOD_KX jited:1 311 PASS
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, if the only instructions using r_X are of the
BPF_LD | BPF_IND type, r_X would not be reset to 0, using whatever
value was there when entering the jited code. With this patch, r_X
will be correctly marked as used so it will be reset to 0 in the
prologue code.
This fix also makes the test "LD_IND byte default X" pass in the
test_bpf module when the ARM JIT is enabled.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some GCC versions (e.g. 4.8.3) can incorrectly inline a function with
MIPS32 instructions into another function with MIPS16 code [1], causing
the assembler to genereate incorrect binary code or fail right away
complaining about unrecognized opcode.
In the case of __arch_swab{16,32}, when inlined by the compiler with
flags `-mips32r2 -mips16 -Os', the assembler can fail with the following
error.
{standard input}:79: Error: unrecognized opcode `wsbh $2,$2'
For performance concerns and to workaround the issue already existing in
older compilers, just ignore these 2 functions when compiling with
mips16 enabled.
[1] Inlining nomips16 function into mips16 function can result in
undefined builtins, https://gcc.gnu.org/bugzilla/show_bug.cgi?id=55777
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11241/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit e0d8b2ec53.
For at least GCC 4.8.3, adding nomips16 function attribute still cannot
prevent it from being inlined in mips16 context. So revert it first in
preparation for a better workaround.
[1] Inlining nomips16 function into mips16 function can result in
undefined builtins, https://gcc.gnu.org/bugzilla/show_bug.cgi?id=55777
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11240/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
Pull MIPS updates from Ralf Baechle:
"This week's round of MIPS fixes:
- Fix JZ4740 build
- Fix fallback to GFP_DMA
- FP seccomp in case of ENOSYS
- Fix bootmem panic
- A number of FP and CPS fixes
- Wire up new syscalls
- Make sure BPF assembler objects can properly be disassembled
- Fix BPF assembler code for MIPS I"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: scall: Always run the seccomp syscall filters
MIPS: Octeon: Fix kernel panic on startup from memory corruption
MIPS: Fix R2300 FP context switch handling
MIPS: Fix octeon FP context switch handling
MIPS: BPF: Fix load delay slots.
MIPS: BPF: Do all exports of symbols with FEXPORT().
MIPS: Fix the build on jz4740 after removing the custom gpio.h
MIPS: CPS: #ifdef on CONFIG_MIPS_MT_SMP rather than CONFIG_MIPS_MT
MIPS: CPS: Don't include MT code in non-MT kernels.
MIPS: CPS: Stop dangling delay slot from has_mt.
MIPS: dma-default: Fix 32-bit fall back to GFP_DMA
MIPS: Wire up userfaultfd and membarrier syscalls.
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When highmem is enabled, there's little reason not to also enable
highpte support as well. Rather than leaving this to chance, make
it an expert option, and default it to be enabled if highmem is
enabled. Add some help text to the option while we're here.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mimicking the same config option on x86, this allows for 1GB systems to
have their RAM entirely mapped as low memory.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently on ARM when <SysRq-L> is triggered from an interrupt handler
(e.g. a SysRq issued using UART or kbd) the main CPU will wedge for ten
seconds with interrupts masked before issuing a backtrace for every CPU
except itself.
The new backtrace code introduced by commit 96f0e00378 ("ARM: add
basic support for on-demand backtrace of other CPUs") does not work
correctly when run from an interrupt handler because IPI_CPU_BACKTRACE
is used to generate the backtrace on all CPUs but cannot preempt the
current calling context.
This can be fixed by detecting that the calling context cannot be
preempted and issuing the backtrace directly in this case. Issuing
directly leaves us without any pt_regs to pass to nmi_cpu_backtrace()
so we also modify the generic code to call dump_stack() when its
argument is NULL.
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dumping registers from other sleeping tasks in KGDB was totally
failing for me. All registers were reported as 0 in many cases.
The code was using task_pt_regs(task) to try to get other thread
registers. This doesn't appear to be the right place to look. From
my tests, I saw non-zero values in this structure when we were looking
at a kernel thread that had a userspace task associated with it, but
it contained the register values from the userspace task. So even in
the cases where registers weren't reported as 0 we were still not
showing the right thing.
Instead of using task_pt_regs(task) let's use task_thread_info(task).
This is the same place that is referred to when doing a dump of all
sleeping task stacks (kdb_show_stack() -> show_stack() ->
dump_backtrace() -> unwind_backtrace() -> thread_saved_sp()).
As further evidence that this is the right thing to do, you can find
the following comment in "gdbstub.c" right before it calls
sleeping_thread_to_gdb_regs():
Pull stuff saved during switch_to; nothing else is accessible (or
even particularly relevant). This should be enough for a stack
trace.
...and if you look at switch_to() it only saves r4-r11, sp and lr.
Those are the same registers that I'm getting out of the
task_thread_info().
With this change you can use "info thread" to see all tasks in the
kernel and you can switch to other tasks and examine them in gdb.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Stephen Boyd <sboyd@codeurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IOMMU-based dma_mmap() implementation lacked proper support for offset
parameter used in mmap call (it always assumed that mapping starts from
offset zero). This patch adds support for offset parameter to IOMMU-based
implementation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.6+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dma_mmap() function in IOMMU-based dma-mapping implementation lacked
a check for valid range of mmap parameters (offset and buffer size), what
might have caused access beyond the allocated buffer. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.6+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brand reports that a NEEDS_SYSCALL_FOR_CMPXCHG enabled kernel would
open a security hole in the ghost syscall used to implement cmpxchg, as
it fails to validate the user pointer.
However, in order for this option to be enabled, you'd need to be
building a pre-ARMv6 kernel with SMP support. There is only one system
known which fits that, which is an early ARM SMP FPGA implementation
based on the ARM926T.
In any case, the Kconfig does not allow SMP to be enabled for pre-ARMv6
systems.
Moreover, even if NEEDS_SYSCALL_FOR_CMPXCHG were to be enabled, the
kernel would not build as __ARM_NR_cmpxchg64 is not defined.
The simple answer is to remove the buggy code.
Reported-by: Mark Brand <markbrand@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add unwinding annotations so that unwinding from this function
works properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Header <asm/kdebug.h> is not needed for arm/hw_breakpoint.c, so remove
the pointless #include.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 904464b91e.
The problem pointed out by commit 904464b91e ("ARM: 7655/1:
smp_twd: make twd_local_timer_of_register() no-op for nosmp")
doesn't exist anymore.
We can safely boot with nosmp and the warning won't show up.
The other side benefit of this patch is that TWD has a chance
to probe on single-core A9 systems such as AM437x which sport
TWD.
While at that, also drop SMP dependency from TWD's Kconfig entry.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull x86 fixes from Ingo Molnar:
"Fixes all around the map: W+X kernel mapping fix, WCHAN fixes, two
build failure fixes for corner case configs, x32 header fix and a
speling fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds
x86/mm: Set NX on gap between __ex_table and rodata
x86/kexec: Fix kexec crash in syscall kexec_file_load()
x86/process: Unify 32bit and 64bit implementations of get_wchan()
x86/process: Add proper bound checks in 64bit get_wchan()
x86, efi, kasan: Fix build failure on !KASAN && KMEMCHECK=y kernels
x86/hyperv: Fix the build in the !CONFIG_KEXEC_CORE case
x86/cpufeatures: Correct spelling of the HWP_NOTIFY flag
Pull EFI fixes from Ingo Molnar:
"Two EFI fixes: one for x86, one for ARM, fixing a boot crash bug that
can trigger under newer EFI firmware"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/efi: Fix boot crash by not padding between EFI_MEMORY_RUNTIME regions
x86/efi: Fix boot crash by mapping EFI memmap entries bottom-up at runtime, instead of top-down
As we need to add further flags to the bpf_prog structure, lets migrate
both bools to a bitfield representation. The size of the base structure
(excluding insns) remains unchanged at 40 bytes.
Add also tags for the kmemchecker, so that it doesn't throw false
positives. Even in case gcc would generate suboptimal code, it's not
being accessed in performance critical paths.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AJCF
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix for transparent huge page change_protection() logic which was
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: fix function_graph tracer panic
arm64: Fix THP protection change logic
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- Fix for accidental modification of arguments of syscall functions
- Wire up new syscalls
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.3-rc1
m68k: Define asmlinkage_protect
m68k: Wire up membarrier
m68k: Wire up userfaultfd
m68k: Wire up direct socket calls
During development it was found that a number of builds would panic
during the kernel init process, more specifically in 'delayed_fput()'.
The panic showed the kernel trying to access a memory address of
'0xb7fdc00' while traversing the 'delayed_fput_list' structure.
Comparing this memory address to the value of the pointer used on
builds that did not panic confirmed that the pointer on crashing
builds must have been corrupted at some stage earlier in the init
process.
By traversing the list earlier and earlier in the code it was found
that 'plat_mem_setup()' was responsible for corrupting the list.
Specifically the line:
memory = cvmx_bootmem_phy_alloc(mem_alloc_size,
__pa_symbol(&__init_end), -1,
0x100000,
CVMX_BOOTMEM_FLAG_NO_LOCKING);
Which would eventually call:
cvmx_bootmem_phy_set_size(new_ent_addr,
cvmx_bootmem_phy_get_size
(ent_addr) -
(desired_min_addr -
ent_addr));
Where 'new_ent_addr'=0x4800000 (the address of 'delayed_fput_list')
and the second argument (size)=0xb7fdc00 (the address causing the
kernel panic). The job of this part of 'plat_mem_setup()' is to
allocate chunks of memory for the kernel to use. At the start of
each chunk of memory the size of the chunk is written, hence the
value 0xb7fdc00 is written onto memory at 0x4800000, therefore the
kernel panics when it goes back to access 'delayed_fput_list' later
on in the initialisation process.
On builds that were not crashing it was found that the compiler had
placed 'delayed_fput_list' at 0x4800008, meaning it wasn't corrupted
(but something else in memory was overwritten).
As can be seen in the first function call above the code begins to
allocate chunks of memory beginning from the symbol '__init_end'.
The MIPS linker script (vmlinux.lds.S) however defines the .bss
section to begin after '__init_end'. Therefore memory within the
.bss section is allocated to the kernel to use (System.map shows
'delayed_fput_list' and other kernel structures to be in .bss).
To stop the kernel panic (and the .bss section being corrupted)
memory should begin being allocated from the symbol '_end'.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: aleksey.makarov@auriga.com
Patchwork: https://patchwork.linux-mips.org/patch/11251/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1a3d59579b ("MIPS: Tidy up FPU context switching") removed FP
context saving from the asm-written resume function in favour of reusing
existing code to perform the same task. However it only removed the FP
context saving code from the r4k_switch.S implementation of resume.
Remove it from the r2300_switch.S implementation too in order to prevent
attempting to save the FP context twice, which would likely lead to an
exception from the second save because the FPU had already been disabled
by the first save.
This patch has only been build tested, using rbtx49xx_defconfig.
Fixes: 1a3d59579b ("MIPS: Tidy up FPU context switching")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The entire bpf_jit_asm.S is written in noreorder mode because "we know
better" according to a comment. This also prevented the assembler from
throwing in the required NOPs for MIPS I processors which have no
load-use interlock, thus the load's consumer might end up using the
old value of the register from prior to the load.
Fixed by putting the assembler in reorder mode for just the affected
load instructions. This is not enough for gas to actually try to be
clever by looking at the next instruction and inserting a nop only
when needed but as the comment said "we know better", so getting gas
to unconditionally emit a NOP is just right in this case and prevents
adding further ifdefery.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On x32, gcc predefines __x86_64__ but long is only 32-bit. Use
__ILP32__ to distinguish x32.
Fixes this compiler error in perf:
tools/include/asm-generic/bitops/__ffs.h: In function '__ffs':
tools/include/asm-generic/bitops/__ffs.h:19:8: error: right shift count >= width of type [-Werror=shift-count-overflow]
word >>= 32;
^
This isn't sufficient to build perf for x32, though.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1443660043.2730.15.camel@decadent.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Unused space between the end of __ex_table and the start of
rodata can be left W+x in the kernel page tables. Extend the
setting of the NX bit to cover this gap by starting from
text_end rather than rodata_start.
Before:
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd
0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte
0xffffffff81754000-0xffffffff81800000 688K RW GLB x pte
0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd
0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte
0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte
0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd
0xffffffff82200000-0xffffffffa0000000 478M pmd
After:
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd
0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte
0xffffffff81754000-0xffffffff81800000 688K RW GLB NX pte
0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd
0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte
0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte
0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd
0xffffffff82200000-0xffffffffa0000000 478M pmd
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1443704662-3138-1-git-send-email-sds@tycho.nsa.gov
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The original bug is a page fault crash that sometimes happens
on big machines when preparing ELF headers:
BUG: unable to handle kernel paging request at ffffc90613fc9000
IP: [<ffffffff8103d645>] prepare_elf64_ram_headers_callback+0x165/0x260
The bug is caused by us under-counting the number of memory ranges
and subsequently not allocating enough ELF header space for them.
The bug is typically masked on smaller systems, because the ELF header
allocation is rounded up to the next page.
This patch modifies the code in fill_up_crash_elf_data() by using
walk_system_ram_res() instead of walk_system_ram_range() to correctly
count the max number of crash memory ranges. That's because the
walk_system_ram_range() filters out small memory regions that
reside in the same page, but walk_system_ram_res() does not.
Here's how I found the bug:
After tracing prepare_elf64_headers() and prepare_elf64_ram_headers_callback(),
the code uses walk_system_ram_res() to fill-in crash memory regions information
to the program header, so it counts those small memory regions that
reside in a page area.
But, when the kernel was using walk_system_ram_range() in
fill_up_crash_elf_data() to count the number of crash memory regions,
it filters out small regions.
I printed those small memory regions, for example:
kexec: Get nr_ram ranges. vaddr=0xffff880077592258 paddr=0x77592258, sz=0xdc0
Based on the code in walk_system_ram_range(), this memory region
will be filtered out:
pfn = (0x77592258 + 0x1000 - 1) >> 12 = 0x77593
end_pfn = (0x77592258 + 0xfc0 -1 + 1) >> 12 = 0x77593
end_pfn - pfn = 0x77593 - 0x77593 = 0 <=== if (end_pfn > pfn) is FALSE
So, the max_nr_ranges that's counted by the kernel doesn't include
small memory regions - causing us to under-allocate the required space.
That causes the page fault crash that happens in a later code path
when preparing ELF headers.
This bug is not easy to reproduce on small machines that have few
CPUs, because the allocated page aligned ELF buffer has more free
space to cover those small memory regions' PT_LOAD headers.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1443531537-29436-1-git-send-email-jlee@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge misc fixes from Andrew Morton:
"12 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dmapool: fix overflow condition in pool_find_page()
thermal: avoid division by zero in power allocator
memcg: remove pcp_counter_lock
kprobes: use _do_fork() in samples to make them work again
drivers/input/joystick/Kconfig: zhenhua.c needs BITREVERSE
memcg: make mem_cgroup_read_stat() unsigned
memcg: fix dirty page migration
dax: fix NULL pointer in __dax_pmd_fault()
mm: hugetlbfs: skip shared VMAs when unmapping private pages to satisfy a fault
mm/slab: fix unexpected index mapping result of kmalloc_size(INDEX_NODE+1)
userfaultfd: remove kernel header include from uapi header
arch/x86/include/asm/efi.h: fix build failure
Bugs have trickled in for a new feature in 4.2 (MTRR support in guests)
so I'm reverting it all; let's not make this -rc period busier for KVM
than it's been so far. This covers the four reverts from me.
The fifth patch is being reverted because Radim found a bug in the
implementation of stable scheduler clock, *but* also managed to implement
the feature entirely without hypervisor support. So instead of fixing
the hypervisor side we can remove it completely; 4.4 will get the new
implementation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWDXc/AAoJEL/70l94x66D8GoH/0WXeSYHn8+Ql5oZ5vI0QcCG
6MiKVixhHTOpkug2QE4DGClYoFSUPuDEB/w6D7YciNn0quDHFZbI3XEMXYtLobHN
0J9cMv9Vpy5pBVMG/LJOw9pFAJRdhSx/cHU2DW9vUiRG9dO9zuxFzBtUciWLOPAX
tSQfDumeUV30BsTP5ldi9kaIUJBM9oBD4JhES0JHx6ePBvy+9vCRmHotugzrrGx6
N+AbCmwUwxnK29PF9i7KMfex6T8l1uQG3fwWVazHoswsqbFEQyF6NpaSTYoZkjM9
6gaXEE1FQ7tRhuio4bBDos0lLu6iGesveP71p/HpULleq2sbH2ER8TpzR5iSnQA=
=zAJS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"(Relatively) a lot of reverts, mostly.
Bugs have trickled in for a new feature in 4.2 (MTRR support in
guests) so I'm reverting it all; let's not make this -rc period busier
for KVM than it's been so far. This covers the four reverts from me.
The fifth patch is being reverted because Radim found a bug in the
implementation of stable scheduler clock, *but* also managed to
implement the feature entirely without hypervisor support. So instead
of fixing the hypervisor side we can remove it completely; 4.4 will
get the new implementation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
Use WARN_ON_ONCE for missing X86_FEATURE_NRIPS
Update KVM homepage Url
Revert "KVM: SVM: use NPT page attributes"
Revert "KVM: svm: handle KVM_X86_QUIRK_CD_NW_CLEARED in svm_get_mt_mask"
Revert "KVM: SVM: Sync g_pat with guest-written PAT value"
Revert "KVM: x86: apply guest MTRR virtualization on host reserved pages"
Revert "KVM: x86: zero kvmclock_offset when vcpu0 initializes kvmclock system MSR"
Currently, BG2Q shares a compatible with BG2. This is incorrect, since
BG2 and BG2Q use different USB PLL dividers. In reality, BG2Q shares a
divider with BG2CD. Change BG2Q's USB PHY compatible string to reflect
that.
Cc: <stable@vger.kernel.org> # v4.2.0-
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
6910fa1 ("arm64: enable PTE type bit in the mask for pte_modify") fixes
a problem whereby a large block of PROT_NONE mapped memory is
incorrectly mapped as block descriptors when mprotect is called.
Unfortunately, a subtle bug was introduced by this fix to the THP logic.
If one mmaps a large block of memory, then faults it such that it is
collapsed into THPs; resulting calls to mprotect on this area of memory
will lead to incorrect table descriptors being written instead of block
descriptors. This is because pmd_modify calls pte_modify which is now
allowed to modify the type of the page table entry.
This patch reverts commit 6910fa16db, and
fixes the problem it was trying to address by adjusting PAGE_NONE to
represent a table entry. Thus no change in pte type is required when
moving from PROT_NONE to a different protection.
Fixes: 6910fa16db ("arm64: enable PTE type bit in the mask for pte_modify")
Cc: <stable@vger.kernel.org> # 4.0+
Cc: Feng Kan <fkan@apm.com>
Reported-by: Ganapatrao Kulkarni <Ganapatrao.Kulkarni@caviumnetworks.com>
Tested-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
FEXPORT also marks the symbol as code using .type symbol, @function.
Without objdump -d will output only a hexdump for code following the
affected symbols.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cpu feature flags are not ever going to change, so warning
everytime can cause a lot of kernel log spam
(in our case more than 10GB/hour).
The warning seems to only occur when nested virtualization is
enabled, so it's probably triggered by a KVM bug. This is a
sensible and safe change anyway, and the KVM bug fix might not
be suitable for stable releases anyway.
Cc: stable@vger.kernel.org
Signed-off-by: Dirk Mueller <dmueller@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 3c2e7f7de3.
Initializing the mapping from MTRR to PAT values was reported to
fail nondeterministically, and it also caused extremely slow boot
(due to caching getting disabled---bug 103321) with assigned devices.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Sebastian Schuette <dracon@ewetel.net>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 5492830370.
It builds on the commit that is being reverted next.
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit e098223b78,
which has a dependency on other commits being reverted.
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
