Jan Kara's analysis of the syzbot report (edited):
The reproducer opens a directory on FUSE filesystem, it then attaches
dnotify mark to the open directory. After that a fuse_do_getattr() call
finds that attributes returned by the server are inconsistent, and calls
make_bad_inode() which, among other things does:
inode->i_mode = S_IFREG;
This then confuses dnotify which doesn't tear down its structures
properly and eventually crashes.
Avoid calling make_bad_inode() on a live inode: switch to a private flag on
the fuse inode. Also add the test to ops which the bad_inode_ops would
have caught.
This bug goes back to the initial merge of fuse in 2.6.14...
Reported-by: syzbot+f427adf9324b92652ccc@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Virtiofs can be slow with small writes if xattr are enabled and we are
doing cached writes (No direct I/O). Ganesh Mahalingam noticed this.
Some debugging showed that file_remove_privs() is called in cached write
path on every write. And everytime it calls security_inode_need_killpriv()
which results in call to __vfs_getxattr(XATTR_NAME_CAPS). And this goes to
file server to fetch xattr. This extra round trip for every write slows
down writes tremendously.
Normally to avoid paying this penalty on every write, vfs has the notion of
caching this information in inode (S_NOSEC). So vfs sets S_NOSEC, if
filesystem opted for it using super block flag SB_NOSEC. And S_NOSEC is
cleared when setuid/setgid bit is set or when security xattr is set on
inode so that next time a write happens, we check inode again for clearing
setuid/setgid bits as well clear any security.capability xattr.
This seems to work well for local file systems but for remote file systems
it is possible that VFS does not have full picture and a different client
sets setuid/setgid bit or security.capability xattr on file and that means
VFS information about S_NOSEC on another client will be stale. So for
remote filesystems SB_NOSEC was disabled by default.
Commit 9e1f1de02c ("more conservative S_NOSEC handling") mentioned that
these filesystems can still make use of SB_NOSEC as long as they clear
S_NOSEC when they are refreshing inode attriutes from server.
So this patch tries to enable SB_NOSEC on fuse (regular fuse as well as
virtiofs). And clear SB_NOSEC when we are refreshing inode attributes.
This is enabled only if server supports FUSE_HANDLE_KILLPRIV_V2. This says
that server will clear setuid/setgid/security.capability on
chown/truncate/write as apporpriate.
This should provide tighter coherency because now suid/sgid/
security.capability will be cleared even if fuse client cache has not seen
these attrs.
Basic idea is that fuse client will trigger suid/sgid/security.capability
clearing based on its attr cache. But even if cache has gone stale, it is
fine because FUSE_HANDLE_KILLPRIV_V2 will make sure WRITE clear
suid/sgid/security.capability.
We make this change only if server supports FUSE_HANDLE_KILLPRIV_V2. This
should make sure that existing filesystems which might be relying on
seucurity.capability always being queried from server are not impacted.
This tighter coherency relies on WRITE showing up on server (and not being
cached in guest). So writeback_cache mode will not provide that tight
coherency and it is not recommended to use two together. Having said that
it might work reasonably well for lot of use cases.
This change improves random write performance very significantly. Running
virtiofsd with cache=auto and following fio command:
fio --ioengine=libaio --direct=1 --name=test --filename=/mnt/virtiofs/random_read_write.fio --bs=4k --iodepth=64 --size=4G --readwrite=randwrite
Bandwidth increases from around 50MB/s to around 250MB/s as a result of
applying this patch. So improvement is very significant.
Link: https://github.com/kata-containers/runtime/issues/2815
Reported-by: "Mahalingam, Ganesh" <ganesh.mahalingam@intel.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
With FUSE_HANDLE_KILLPRIV_V2 support, server will need to kill suid/sgid/
security.capability on open(O_TRUNC), if server supports
FUSE_ATOMIC_O_TRUNC.
But server needs to kill suid/sgid only if caller does not have CAP_FSETID.
Given server does not have this information, client needs to send this info
to server.
So add a flag FUSE_OPEN_KILL_SUIDGID to fuse_open_in request which tells
server to kill suid/sgid (only if group execute is set).
This flag is added to the FUSE_OPEN request, as well as the FUSE_CREATE
request if the create was non-exclusive, since that might result in an
existing file being opened/truncated.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
If client does a write() on a suid/sgid file, VFS will first call
fuse_setattr() with ATTR_KILL_S[UG]ID set. This requires sending setattr
to file server with ATTR_MODE set to kill suid/sgid. But to do that client
needs to know latest mode otherwise it is racy.
To reduce the race window, current code first call fuse_do_getattr() to get
latest ->i_mode and then resets suid/sgid bits and sends rest to server
with setattr(ATTR_MODE). This does not reduce the race completely but
narrows race window significantly.
With fc->handle_killpriv_v2 enabled, it should be possible to remove this
race completely. Do not kill suid/sgid with ATTR_MODE at all. It will be
killed by server when WRITE request is sent to server soon. This is
similar to fc->handle_killpriv logic. V2 is just more refined version of
protocol. Hence this patch does not send ATTR_MODE to kill suid/sgid if
fc->handle_killpriv_v2 is enabled.
This creates an issue if fc->writeback_cache is enabled. In that case
WRITE can be cached in guest and server might not see WRITE request and
hence will not kill suid/sgid. Miklos suggested that in such cases, we
should fallback to a writethrough WRITE instead and that will generate
WRITE request and kill suid/sgid. This patch implements that too.
But this relies on client seeing the suid/sgid set. If another client sets
suid/sgid and this client does not see it immideately, then we will not
fallback to writethrough WRITE. So this is one limitation with both
fc->handle_killpriv_v2 and fc->writeback_cache enabled. Both the options
are not fully compatible. But might be good enough for many use cases.
Note: This patch is not checking whether security.capability is set or not
when falling back to writethrough path. If suid/sgid is not set and
only security.capability is set, that will be taken care of by
file_remove_privs() call in ->writeback_cache path.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
If fc->handle_killpriv_v2 is enabled, we expect file server to clear
suid/sgid/security.capbility upon chown/truncate/write as appropriate.
Upon truncate (ATTR_SIZE), suid/sgid are cleared only if caller does not
have CAP_FSETID. File server does not know whether caller has CAP_FSETID
or not. Hence set FATTR_KILL_SUIDGID upon truncate to let file server know
that caller does not have CAP_FSETID and it should kill suid/sgid as
appropriate.
On chown (ATTR_UID/ATTR_GID) suid/sgid need to be cleared irrespective of
capabilities of calling process, so set FATTR_KILL_SUIDGID unconditionally
in that case.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
With HANDLE_KILLPRIV_V2, server will need to kill suid/sgid if caller does
not have CAP_FSETID. We already have a flag FUSE_WRITE_KILL_SUIDGID in
WRITE request and we already set it in direct I/O path.
To make it work in cached write path also, start setting
FUSE_WRITE_KILL_SUIDGID in this path too.
Set it only if fc->handle_killpriv_v2 is set. Otherwise client is
responsible for kill suid/sgid.
In case of direct I/O we set FUSE_WRITE_KILL_SUIDGID unconditionally
because we don't call file_remove_privs() in that path (with cache=none
option).
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Kernel has:
ATTR_KILL_PRIV -> clear "security.capability"
ATTR_KILL_SUID -> clear S_ISUID
ATTR_KILL_SGID -> clear S_ISGID if executable
Fuse has:
FUSE_WRITE_KILL_PRIV -> clear S_ISUID and S_ISGID if executable
So FUSE_WRITE_KILL_PRIV implies the complement of ATTR_KILL_PRIV, which is
somewhat confusing. Also PRIV implies all privileges, including
"security.capability".
Change the name to FUSE_WRITE_KILL_SUIDGID and make FUSE_WRITE_KILL_PRIV an
alias to perserve API compatibility
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
We already have FUSE_HANDLE_KILLPRIV flag that says that file server will
remove suid/sgid/caps on truncate/chown/write. But that's little different
from what Linux VFS implements.
To be consistent with Linux VFS behavior what we want is.
- caps are always cleared on chown/write/truncate
- suid is always cleared on chown, while for truncate/write it is cleared
only if caller does not have CAP_FSETID.
- sgid is always cleared on chown, while for truncate/write it is cleared
only if caller does not have CAP_FSETID as well as file has group execute
permission.
As previous flag did not provide above semantics. Implement a V2 of the
protocol with above said constraints.
Server does not know if caller has CAP_FSETID or not. So for the case
of write()/truncate(), client will send information in special flag to
indicate whether to kill priviliges or not. These changes are in subsequent
patches.
FUSE_HANDLE_KILLPRIV_V2 relies on WRITE being sent to server to clear
suid/sgid/security.capability. But with ->writeback_cache, WRITES are
cached in guest. So it is not recommended to use FUSE_HANDLE_KILLPRIV_V2
and writeback_cache together. Though it probably might be good enough
for lot of use cases.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Failure to do so may result in EEXIST even if the file only exists in the
cache and not in the filesystem.
The atomic nature of O_EXCL mandates that the cached state should be
ignored and existence verified anew.
Reported-by: Ken Schalk <kschalk@nvidia.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fuse mount now only ever has a refcount of one (before being freed) so the
count field is unnecessary.
Remove the refcounting and fold fuse_mount_put() into callers. The only
caller of fuse_mount_put() where fm->fc was NULL is fuse_dentry_automount()
and here the fuse_conn_put() can simply be omitted.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Currently when acquiring an sb for virtiofs fuse_mount_get() is being
called from virtio_fs_set_super() if a new sb is being filled and
fuse_mount_put() is called unconditionally after sget_fc() returns.
The exact same result can be obtained by checking whether
fs_contex->s_fs_info was set to NULL (ref trasferred to sb->s_fs_info) and
only calling fuse_mount_put() if the ref wasn't transferred (error or
matching sb found).
This allows getting rid of virtio_fs_set_super() and fuse_mount_get().
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
This can be triggered for example by adding the "-omand" mount option,
which will be rejected and virtio_fs_fill_super() will return an error.
In such a case the allocations for fuse_conn and fuse_mount will leak due
to s_root not yet being set and so ->put_super() not being called.
Fixes: a62a8ef9d9 ("virtio-fs: add virtiofs filesystem")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Qian Cai reports that the WARNING in tree_insert() can be triggered by a
fuzzer with the following call chain:
invalidate_inode_pages2_range()
fuse_launder_page()
fuse_writepage_locked()
tree_insert()
The reason is that another write for the same page is already queued.
The simplest fix is to wait until the pending write is completed and only
after that queue the new write.
Since this case is very rare, the additional wait should not be a problem.
Reported-by: Qian Cai <cai@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSQHSd0lITzzeNWNm3h3BK/laaZPAUCX4n0/gAKCRDh3BK/laaZ
PM3jAP4xhaix0j/y3VyaxsUqWg6ZSrjq6X0o9clGMJv27IAtjgD/fJ7ZwzTldojD
qb7N3utjLiPVRjwFmvsZ8JZ7O7PbwQ0=
=oUbZ
-----END PGP SIGNATURE-----
Merge tag 'fuse-update-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi:
- Support directly accessing host page cache from virtiofs. This can
improve I/O performance for various workloads, as well as reducing
the memory requirement by eliminating double caching. Thanks to Vivek
Goyal for doing most of the work on this.
- Allow automatic submounting inside virtiofs. This allows unique
st_dev/ st_ino values to be assigned inside the guest to files
residing on different filesystems on the host. Thanks to Max Reitz
for the patches.
- Fix an old use after free bug found by Pradeep P V K.
* tag 'fuse-update-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse: (25 commits)
virtiofs: calculate number of scatter-gather elements accurately
fuse: connection remove fix
fuse: implement crossmounts
fuse: Allow fuse_fill_super_common() for submounts
fuse: split fuse_mount off of fuse_conn
fuse: drop fuse_conn parameter where possible
fuse: store fuse_conn in fuse_req
fuse: add submount support to <uapi/linux/fuse.h>
fuse: fix page dereference after free
virtiofs: add logic to free up a memory range
virtiofs: maintain a list of busy elements
virtiofs: serialize truncate/punch_hole and dax fault path
virtiofs: define dax address space operations
virtiofs: add DAX mmap support
virtiofs: implement dax read/write operations
virtiofs: introduce setupmapping/removemapping commands
virtiofs: implement FUSE_INIT map_alignment field
virtiofs: keep a list of free dax memory ranges
virtiofs: add a mount option to enable dax
virtiofs: set up virtio_fs dax_device
...
virtiofs currently maps various buffers in scatter gather list and it looks
at number of pages (ap->pages) and assumes that same number of pages will
be used both for input and output (sg_count_fuse_req()), and calculates
total number of scatterlist elements accordingly.
But looks like this assumption is not valid in all the cases. For example,
Cai Qian reported that trinity, triggers warning with virtiofs sometimes.
A closer look revealed that if one calls ioctl(fd, 0x5a004000, buf), it
will trigger following warning.
WARN_ON(out_sgs + in_sgs != total_sgs)
In this case, total_sgs = 8, out_sgs=4, in_sgs=3. Number of pages is 2
(ap->pages), but out_sgs are using both the pages but in_sgs are using
only one page. In this case, fuse_do_ioctl() sets different size values
for input and output.
args->in_args[args->in_numargs - 1].size == 6656
args->out_args[args->out_numargs - 1].size == 4096
So current method of calculating how many scatter-gather list elements
will be used is not accurate. Make calculations more precise by parsing
size and ap->descs.
Reported-by: Qian Cai <cai@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Link: https://lore.kernel.org/linux-fsdevel/5ea77e9f6cb8c2db43b09fbd4158ab2d8c066a0a.camel@redhat.com/
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
Re-add lost removal of fc from fuse_conn_list and the control filesystem.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Fixes: fcee216beb ("fuse: split fuse_mount off of fuse_conn")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
FUSE servers can indicate crossmount points by setting FUSE_ATTR_SUBMOUNT
in fuse_attr.flags. The inode will then be marked as S_AUTOMOUNT, and the
.d_automount implementation creates a new submount at that location, so
that the submount gets a distinct st_dev value.
Note that all submounts get a distinct superblock and a distinct st_dev
value, so for virtio-fs, even if the same filesystem is mounted more than
once on the host, none of its mount points will have the same st_dev. We
need distinct superblocks because the superblock points to the root node,
but the different host mounts may show different trees (e.g. due to
submounts in some of them, but not in others).
Right now, this behavior is only enabled when fuse_conn.auto_submounts is
set, which is the case only for virtio-fs.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Replace BDI_CAP_NO_ACCT_WB with a positive BDI_CAP_WRITEBACK_ACCT to
make the checks more obvious. Also remove the pointless
bdi_cap_account_writeback wrapper that just obsfucates the check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set up a readahead size by default, as very few users have a good
reason to change it. This means code, ecryptfs, and orangefs now
set up the values while they were previously missing it, while ubifs,
mtd and vboxsf manually set it to 0 to avoid readahead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Richard Weinberger <richard@nod.at> [ubifs, mtd]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Submounts have their own superblock, which needs to be initialized.
However, they do not have a fuse_fs_context associated with them, and
the root node's attributes should be taken from the mountpoint's node.
Extend fuse_fill_super_common() to work for submounts by making the @ctx
parameter optional, and by adding a @submount_finode parameter.
(There is a plain "unsigned" in an existing code block that is being
indented by this commit. Extend it to "unsigned int" so checkpatch does
not complain.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
We want to allow submounts for the same fuse_conn, but with different
superblocks so that each of the submounts has its own device ID. To do
so, we need to split all mount-specific information off of fuse_conn
into a new fuse_mount structure, so that multiple mounts can share a
single fuse_conn.
We need to take care only to perform connection-level actions once (i.e.
when the fuse_conn and thus the first fuse_mount are established, or
when the last fuse_mount and thus the fuse_conn are destroyed). For
example, fuse_sb_destroy() must invoke fuse_send_destroy() until the
last superblock is released.
To do so, we keep track of which fuse_mount is the root mount and
perform all fuse_conn-level actions only when this fuse_mount is
involved.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
With the last commit, all functions that handle some existing fuse_req
no longer need to be given the associated fuse_conn, because they can
get it from the fuse_req object.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Every fuse_req belongs to a fuse_conn. Right now, we always know which
fuse_conn that is based on the respective device, but we want to allow
multiple (sub)mounts per single connection, and then the corresponding
filesystem is not going to be so trivial to obtain.
Storing a pointer to the associated fuse_conn in every fuse_req will
allow us to trivially find any request's superblock (and thus
filesystem) even then.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
After unlock_request() pages from the ap->pages[] array may be put (e.g. by
aborting the connection) and the pages can be freed.
Prevent use after free by grabbing a reference to the page before calling
unlock_request().
The original patch was created by Pradeep P V K.
Reported-by: Pradeep P V K <ppvk@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
the callers rely upon having any iov_iter_truncate() done inside
->direct_IO() countered by iov_iter_reexpand().
Reported-by: Qian Cai <cai@redhat.com>
Tested-by: Qian Cai <cai@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add logic to free up a busy memory range. Freed memory range will be
returned to free pool. Add a worker which can be started to select
and free some busy memory ranges.
Process can also steal one of its busy dax ranges if free range is not
available. I will refer it to as direct reclaim.
If free range is not available and nothing can't be stolen from same
inode, caller waits on a waitq for free range to become available.
For reclaiming a range, as of now we need to hold following locks in
specified order.
down_write(&fi->i_mmap_sem);
down_write(&fi->dax->sem);
We look for a free range in following order.
A. Try to get a free range.
B. If not, try direct reclaim.
C. If not, wait for a memory range to become free
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
This list will be used selecting fuse_dax_mapping to free when number of
free mappings drops below a threshold.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Currently in fuse we don't seem have any lock which can serialize fault
path with truncate/punch_hole path. With dax support I need one for
following reasons.
1. Dax requirement
DAX fault code relies on inode size being stable for the duration of
fault and want to serialize with truncate/punch_hole and they explicitly
mention it.
static vm_fault_t dax_iomap_pmd_fault(struct vm_fault *vmf, pfn_t *pfnp,
const struct iomap_ops *ops)
/*
* Check whether offset isn't beyond end of file now. Caller is
* supposed to hold locks serializing us with truncate / punch hole so
* this is a reliable test.
*/
max_pgoff = DIV_ROUND_UP(i_size_read(inode), PAGE_SIZE);
2. Make sure there are no users of pages being truncated/punch_hole
get_user_pages() might take references to page and then do some DMA
to said pages. Filesystem might truncate those pages without knowing
that a DMA is in progress or some I/O is in progress. So use
dax_layout_busy_page() to make sure there are no such references
and I/O is not in progress on said pages before moving ahead with
truncation.
3. Limitation of kvm page fault error reporting
If we are truncating file on host first and then removing mappings in
guest lateter (truncate page cache etc), then this could lead to a
problem with KVM. Say a mapping is in place in guest and truncation
happens on host. Now if guest accesses that mapping, then host will
take a fault and kvm will either exit to qemu or spin infinitely.
IOW, before we do truncation on host, we need to make sure that guest
inode does not have any mapping in that region or whole file.
4. virtiofs memory range reclaim
Soon I will introduce the notion of being able to reclaim dax memory
ranges from a fuse dax inode. There also I need to make sure that
no I/O or fault is going on in the reclaimed range and nobody is using
it so that range can be reclaimed without issues.
Currently if we take inode lock, that serializes read/write. But it does
not do anything for faults. So I add another semaphore fuse_inode->i_mmap_sem
for this purpose. It can be used to serialize with faults.
As of now, I am adding taking this semaphore only in dax fault path and
not regular fault path because existing code does not have one. May
be existing code can benefit from it as well to take care of some
races, but that we can fix later if need be. For now, I am just focussing
only on DAX path which is new path.
Also added logic to take fuse_inode->i_mmap_sem in
truncate/punch_hole/open(O_TRUNC) path to make sure file truncation and
fuse dax fault are mutually exlusive and avoid all the above problems.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
This is done along the lines of ext4 and xfs. I primarily wanted
->writepages hook at this time so that I could call into
dax_writeback_mapping_range(). This in turn will decide which pfns need to
be written back.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
This patch implements basic DAX support. mmap() is not implemented
yet and will come in later patches. This patch looks into implemeting
read/write.
We make use of interval tree to keep track of per inode dax mappings.
Do not use dax for file extending writes, instead just send WRITE message
to daemon (like we do for direct I/O path). This will keep write and
i_size change atomic w.r.t crash.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Peng Tao <tao.peng@linux.alibaba.com>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
The device communicates FUSE_SETUPMAPPING/FUSE_REMOVMAPPING alignment
constraints via the FUST_INIT map_alignment field. Parse this field and
ensure our DAX mappings meet the alignment constraints.
We don't actually align anything differently since our mappings are
already 2MB aligned. Just check the value when the connection is
established. If it becomes necessary to honor arbitrary alignments in
the future we'll have to adjust how mappings are sized.
The upshot of this commit is that we can be confident that mappings will
work even when emulating x86 on Power and similar combinations where the
host page sizes are different.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Divide the dax memory range into fixed size ranges (2MB for now) and put
them in a list. This will track free ranges. Once an inode requires a
free range, we will take one from here and put it in interval-tree
of ranges assigned to inode.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Peng Tao <tao.peng@linux.alibaba.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Add a mount option to allow using dax with virtio_fs.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Setup a dax device.
Use the shm capability to find the cache entry and map it.
The DAX window is accessed by the fs/dax.c infrastructure and must have
struct pages (at least on x86). Use devm_memremap_pages() to map the
DAX window PCI BAR and allocate struct page.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
This option was introduced so that for virtio_fs we don't show any mounts
options fuse_show_options(). Because we don't offer any of these options
to be controlled by mounter.
Very soon we are planning to introduce option "dax" which mounter should
be able to specify. And no_mount_options does not work anymore.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
This reduces code duplication and make it little easier to read code.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
As stated in https://sourceforge.net/projects/fuse/, "the FUSE project has
moved to https://github.com/libfuse/" in 22-Dec-2015. Update URLs to
reflect this.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
IRQ bypass support for vdpa and IFC
MLX5 vdpa driver
Endian-ness fixes for virtio drivers
Misc other fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl8yVEwPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpNPEH/0Dtq1s1V4r/kxtLUoMophv9wuORpWCr98BQ
2aOveTmwTOVdZVOiw2tzTgO9nbWx+cL2HvkU7Aajfpz5hh93Z2VOo2n4a7hBC79f
rlc3GXiG+pMk5RfmqGofIHTU+D6ony4D5SXlUDurLdtEwunyuqZwABiWkZjdclZJ
bv90IL8Upzbz0rxYr7k3z8UepdOCt7r4QS/o7STHZBjJRyylxmO/R2yTnh6PtpRK
Q/z35wJBJ3SKc8X3Fi0VOOSeGNZOiypkkl9ZnLVY5lExNAU1+2MMn2UK119SlCDV
MSxb7quYFF4cksXH1g77GMBNi1uADRh1dtFMZdkKhZGljGxKLxo=
=6VTZ
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- IRQ bypass support for vdpa and IFC
- MLX5 vdpa driver
- Endianness fixes for virtio drivers
- Misc other fixes
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (71 commits)
vdpa/mlx5: fix up endian-ness for mtu
vdpa: Fix pointer math bug in vdpasim_get_config()
vdpa/mlx5: Fix pointer math in mlx5_vdpa_get_config()
vdpa/mlx5: fix memory allocation failure checks
vdpa/mlx5: Fix uninitialised variable in core/mr.c
vdpa_sim: init iommu lock
virtio_config: fix up warnings on parisc
vdpa/mlx5: Add VDPA driver for supported mlx5 devices
vdpa/mlx5: Add shared memory registration code
vdpa/mlx5: Add support library for mlx5 VDPA implementation
vdpa/mlx5: Add hardware descriptive header file
vdpa: Modify get_vq_state() to return error code
net/vdpa: Use struct for set/get vq state
vdpa: remove hard coded virtq num
vdpasim: support batch updating
vhost-vdpa: support IOTLB batching hints
vhost-vdpa: support get/set backend features
vhost: generialize backend features setting/getting
vhost-vdpa: refine ioctl pre-processing
vDPA: dont change vq irq after DRIVER_OK
...
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
The ioctl encoding for this parameter is a long but the documentation says
it should be an int and the kernel drivers expect it to be an int. If the
fuse driver treats this as a long it might end up scribbling over the stack
of a userspace process that only allocated enough space for an int.
This was previously discussed in [1] and a patch for fuse was proposed in
[2]. From what I can tell the patch in [2] was nacked in favor of adding
new, "fixed" ioctls and using those from userspace. However there is still
no "fixed" version of these ioctls and the fact is that it's sometimes
infeasible to change all userspace to use the new one.
Handling the ioctls specially in the fuse driver seems like the most
pragmatic way for fuse servers to support them without causing crashes in
userspace applications that call them.
[1]: https://lore.kernel.org/linux-fsdevel/20131126200559.GH20559@hall.aurel32.net/T/
[2]: https://sourceforge.net/p/fuse/mailman/message/31771759/
Signed-off-by: Chirantan Ekbote <chirantan@chromium.org>
Fixes: 59efec7b90 ("fuse: implement ioctl support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
fuse_writepages() ignores some errors taken from fuse_writepages_fill() I
believe it is a bug: if .writepages is called with WB_SYNC_ALL it should
either guarantee that all data was successfully saved or return error.
Fixes: 26d614df1d ("fuse: Implement writepages callback")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
fuse_writepages_fill uses following construction:
if (wpa && ap->num_pages &&
(A || B || C)) {
action;
} else if (wpa && D) {
if (E) {
the same action;
}
}
- ap->num_pages check is always true and can be removed
- "if" and "else if" calls the same action and can be merged.
Move checking A, B, C, D, E conditions to a helper, add comments.
Original-patch-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Previous patch changed handling of remount/reconfigure to ignore all
options, including those that are unknown to the fuse kernel fs. This was
done for backward compatibility, but this likely only affects the old
mount(2) API.
The new fsconfig(2) based reconfiguration could possibly be improved. This
would make the new API less of a drop in replacement for the old, OTOH this
is a good chance to get rid of some weirdnesses in the old API.
Several other behaviors might make sense:
1) unknown options are rejected, known options are ignored
2) unknown options are rejected, known options are rejected if the value
is changed, allowed otherwise
3) all options are rejected
Prior to the backward compatibility fix to ignore all options all known
options were accepted (1), even if they change the value of a mount
parameter; fuse_reconfigure() does not look at the config values set by
fuse_parse_param().
To fix that we'd need to verify that the value provided is the same as set
in the initial configuration (2). The major drawback is that this is much
more complex than just rejecting all attempts at changing options (3);
i.e. all options signify initial configuration values and don't make sense
on reconfigure.
This patch opts for (3) with the rationale that no mount options are
reconfigurable in fuse.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
