The commit 08f3dff799 (mmc: sdhci-of-dwcmshc: add rockchip platform
support") introduces the use of_device_get_match_data() to check for some
chips. Unfortunately, it also breaks the BlueField-3 FW, which uses ACPI.
To fix the problem, let's add the ACPI match data and the corresponding
quirks to re-enable the support for the BlueField-3 SoC.
Reviewed-by: David Woods <davwoods@nvidia.com>
Signed-off-by: Liming Sun <limings@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 08f3dff799 ("mmc: sdhci-of-dwcmshc: add rockchip platform support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220809173742.178440-1-limings@nvidia.com
[Ulf: Clarified the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we don't clear MSDC interrupts when cqe off/disable, which led
to the data complete interrupt will be reserved for the next command.
If the next command with data transfer after cqe off/disable, we process
the CMD ready interrupt and trigger DMA start for data, but the data
complete interrupt is already exists, then SW assume that the data transfer
is complete, SW will trigger DMA stop, but the data may not be transmitted
yet or is transmitting, so we may encounter the following error:
mtk-msdc 11230000.mmc: CMD bus busy detected.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220728080048.21336-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Add support for the asynchronous SDIO wakeup interrupts
- Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
- Add support to store error stats from host drivers
- Extend debugfs to show error stats from host drivers
- Add single I/O read support in the recovery path for 4k sector cards
MMC host:
- dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
- dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
- mmc_spi: Convert corresponding DT bindings to the dtschema
- mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
- mtk-sd: Add support for SDIO wake irqs
- mtk-sd: Add support for the Mediatek MT8188 variant
- renesas_sdhi: Drop redundant manual tap correction for newer SoCs
- renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
- sdhci/cqhci: Add support to capture stats from host errors
- sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
- sdhci-msm: Add support for the MSM8998 and SM8450 variant
- sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
- sdhci-pci-gli: Improve I/O read/write performance for GL9763E
- sdhci-s3c: Convert corresponding DT bindings to the dtschema
- tmio: Avoid glitches when resetting
MEMSTICK core:
- A couple of minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=Rmw5
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for the asynchronous SDIO wakeup interrupts
- Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
- Add support to store error stats from host drivers
- Extend debugfs to show error stats from host drivers
- Add single I/O read support in the recovery path for 4k sector cards
MMC host:
- dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
- dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
- mmc_spi: Convert corresponding DT bindings to the dtschema
- mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
- mtk-sd: Add support for SDIO wake irqs
- mtk-sd: Add support for the Mediatek MT8188 variant
- renesas_sdhi: Drop redundant manual tap correction for newer SoCs
- renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
- sdhci/cqhci: Add support to capture stats from host errors
- sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
- sdhci-msm: Add support for the MSM8998 and SM8450 variant
- sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
- sdhci-pci-gli: Improve I/O read/write performance for GL9763E
- sdhci-s3c: Convert corresponding DT bindings to the dtschema
- tmio: Avoid glitches when resetting
MEMSTICK core:
- A couple of minor fixes and cleanups"
* tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (61 commits)
mmc: mediatek: add support for SDIO eint wakup IRQ
mmc: core: Add support for SDIO wakeup interrupt
dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
dt-bindings: mmc: rockchip-dw-mshc: Document Rockchip RV1126
mmc: renesas_sdhi: newer SoCs don't need manual tap correction
mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
mmc: cavium-octeon: Add of_node_put() when breaking out of loop
mmc: core: quirks: Add of_node_put() when breaking out of loop
mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
dt-bindings: mmc: sdhci-msm: Document the SM8450 compatible
mmc: sdhci-msm: drop redundant of_device_id entries
dt-bindings: mmc: sdhci-msm: add MSM8998
mmc: block: Add single read for 4k sector cards
mmc: mxcmmc: Use mmc_card_sdio macro
mmc: core: Use mmc_card_* macro and add a new for the sd_combo type
dt-bindings: mmc: sdhci-msm: constrain reg-names per variants
dt-bindings: mmc: sdhci-msm: fix reg-names entries
dt-bindings: mmc: Add compatible for MediaTek MT8188
dt-bindings: mmc: sdhci-msm: document resets
mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
This KUnit update for Linux 5.20-rc1 consists of several fixes and an
important feature to discourage running KUnit tests on production
systems. Running tests on a production system could leave the system
in a bad state. This new feature adds:
- adds a new taint type, TAINT_TEST to signal that a test has been run.
This should discourage people from running these tests on production
systems, and to make it easier to tell if tests have been run
accidentally (by loading the wrong configuration, etc.)
- several documentation and tool enhancements and fixes.
-----BEGIN PGP SIGNATURE-----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=WzBX
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit updates from Shuah Khan:
"This consists of several fixes and an important feature to discourage
running KUnit tests on production systems. Running tests on a
production system could leave the system in a bad state.
Summary:
- Add a new taint type, TAINT_TEST to signal that a test has been
run.
This should discourage people from running these tests on
production systems, and to make it easier to tell if tests have
been run accidentally (by loading the wrong configuration, etc)
- Several documentation and tool enhancements and fixes"
* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
Documentation: KUnit: Fix example with compilation error
Documentation: kunit: Add CLI args for kunit_tool
kcsan: test: Add a .kunitconfig to run KCSAN tests
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
nitro_enclaves: test: Use kunit_test_suite() macro
thunderbolt: test: Use kunit_test_suite() macro
kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
kunit: unify module and builtin suite definitions
selftest: Taint kernel when test module loaded
module: panic: Taint the kernel when selftest modules load
Documentation: kunit: fix example run_kunit func to allow spaces in args
Documentation: kunit: Cleanup run_wrapper, fix x-ref
kunit: test.h: fix a kernel-doc markup
kunit: tool: Enable virtio/PCI by default on UML
kunit: tool: make --kunitconfig repeatable, blindly concat
kunit: add coverage_uml.config to enable GCOV on UML
kunit: tool: refactor internal kconfig handling, allow overriding
kunit: tool: introduce --qemu_args
...
-----BEGIN PGP SIGNATURE-----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=celk
-----END PGP SIGNATURE-----
Merge tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Improve the type checking of request flags (Bart)
- Ensure queue mapping for a single queues always picks the right queue
(Bart)
- Sanitize the io priority handling (Jan)
- rq-qos race fix (Jinke)
- Reserved tags handling improvements (John)
- Separate memory alignment from file/disk offset aligment for O_DIRECT
(Keith)
- Add new ublk driver, userspace block driver using io_uring for
communication with the userspace backend (Ming)
- Use try_cmpxchg() to cleanup the code in various spots (Uros)
- Finally remove bdevname() (Christoph)
- Clean up the zoned device handling (Christoph)
- Clean up independent access range support (Christoph)
- Clean up and improve block sysfs handling (Christoph)
- Clean up and improve teardown of block devices.
This turns the usual two step process into something that is simpler
to implement and handle in block drivers (Christoph)
- Clean up chunk size handling (Christoph)
- Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
Ming, Sebastian, Yang, Ying)
* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
ublk_drv: fix double shift bug
ublk_drv: make sure that correct flags(features) returned to userspace
ublk_drv: fix error handling of ublk_add_dev
ublk_drv: fix lockdep warning
block: remove __blk_get_queue
block: call blk_mq_exit_queue from disk_release for never added disks
blk-mq: fix error handling in __blk_mq_alloc_disk
ublk: defer disk allocation
ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
ublk: cleanup ublk_ctrl_uring_cmd
ublk: simplify ublk_ch_open and ublk_ch_release
ublk: remove the empty open and release block device operations
ublk: remove UBLK_IO_F_PREFLUSH
ublk: add a MAINTAINERS entry
block: don't allow the same type rq_qos add more than once
mmc: fix disk/queue leak in case of adding disk failure
ublk_drv: fix an IS_ERR() vs NULL check
ublk: remove UBLK_IO_F_INTEGRITY
ublk_drv: remove unneeded semicolon
...
Merge ACPI device object management changes for v5.20-rc1.
- Use the facilities provided by the driver core and some additional
helpers to handle the children of a given ACPI device object in
multiple places instead of using the children and node list heads in
struct acpi_device which is error prone (Rafael Wysocki).
- Fix ACPI-related device reference counting issue in the hisi_lpc bus
driver (Yang Yingliang).
- Drop the children and node list heads that are not needed any more
from struct acpi_device (Rafael Wysocki).
- Drop driver member from struct acpi_device (Uwe Kleine-König).
- Drop redundant check from acpi_device_remove() (Uwe Kleine-König).
* acpi-bus:
ACPI: bus: Drop unused list heads from struct acpi_device
hisi_lpc: Use acpi_dev_for_each_child()
bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
ACPI: bus: Drop driver member of struct acpi_device
ACPI: bus: Drop redundant check in acpi_device_remove()
mfd: core: Use acpi_dev_for_each_child()
ACPI / MMC: PM: Unify fixing up device power
soundwire: Use acpi_dev_for_each_child()
platform/x86/thinkpad_acpi: Use acpi_dev_for_each_child()
ACPI: scan: Walk ACPI device's children using driver core
ACPI: bus: Introduce acpi_dev_for_each_child_reverse()
ACPI: video: Use acpi_dev_for_each_child()
ACPI: bus: Export acpi_dev_for_each_child() to modules
ACPI: property: Use acpi_dev_for_each_child() for child lookup
ACPI: container: Use acpi_dev_for_each_child()
USB: ACPI: Replace usb_acpi_find_port() with acpi_find_child_by_adr()
thunderbolt: ACPI: Replace tb_acpi_find_port() with acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_dev_has_children()
ACPI: glue: Use acpi_dev_for_each_child()
Add support for eint IRQ when MSDC is used as an SDIO host. This
feature requires SDIO device support async IRQ function. With this
feature, SDIO host can be awakened by SDIO card in suspend state,
without additional pin.
MSDC driver will time-share the SDIO DAT1 pin. During suspend, MSDC
turn off clock and switch SDIO DAT1 pin to GPIO mode. And during
resume, switch GPIO function back to DAT1 mode then turn on clock.
Some device tree property should be added or modified in MSDC node
to support SDIO eint IRQ. Pinctrls "state_eint" is mandatory. Since
this feature depends on asynchronous interrupts, "wakeup-source",
"keep-power-in-suspend" and "cap-sdio-irq" flags are necessary, and
the interrupts list should be extended(the interrupt named with
sdio_wakeup):
&mmcX {
...
interrupt-names = "msdc", "sdio_wakeup";
interrupts-extended = <...>,
<&pio xxx IRQ_TYPE_LEVEL_LOW>;
...
pinctrl-names = "default", "state_uhs", "state_eint";
...
pinctrl-2 = <&mmc2_pins_eint>;
...
cap-sdio-irq;
keep-power-in-suspend;
wakeup-source;
...
};
Co-developed-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-4-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If wakeup-source flag is set in host dts node, parse EAI information
from SDIO CCCR interrupt externsion segment for in-band wakeup. If
async interrupt is supported by SDIO card then enable it and set
enable_async_irq flag in sdio_cccr structure to 1. The parse flow is
implemented in sdio_read_cccr().
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-3-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newest Gen3 SoCs and Gen4 SoCs do not need manual tap correction
with HS400 anymore. So, instead of checking the SDHI version, add a
quirk flag and set manual tap correction only for affected SoCs.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased, renamed the quirk variable, removed stale comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220720072901.1266-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In thunder_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 166bac38c3 ("mmc: cavium: Add MMC PCI driver for ThunderX SOCs")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-2-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In octeon_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 01d9584333 ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In mmc_fixup_of_compatible_match(), we should call of_node_put()
when breaking out of for_each_child_of_node() which will increase
and decrease the refcount during one iteration.
Fixes: b360b11026 ("mmc: core: allow to match the device tree to apply quirks")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220719091051.1210806-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use clk_get_rate for base_clk on resume before setting new rate.
This change ensures that the clock api returns current rate
and sets the clock to the desired rate and honors CLK_GET_NO_CACHE
attribute used by clock api.
Fixes: 97904a5985 (mmc: sdhci-brcmstb: Add ability to increase max clock rate for 72116b0)
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220714174132.18541-1-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts three commits:
1. Revert "mmc: sdhci-msm: Add compatible string check for sdx65"
This reverts commit 953706844f.
2. Revert "mmc: sdhci-msm: Add compatible string check for sm8150"
This reverts commit 5acd6adb65.
3. Revert "mmc: sdhci-msm: Add SoC specific compatibles"
This reverts commit 466614a976.
The oldest commit 466614a976 ("mmc: sdhci-msm: Add SoC specific
compatibles") did not specify what benefits such multiple compatibles
bring, therefore assume there is none. On the other hand such approach
brings a lot of churn to driver maintenance by expecting commit for
every new compatible, even though it is already covered by the fallback.
There is really no sense in duplicating of_device_id for each
variant, which is already covered by generic compatible fallback
qcom,sdhci-msm-v4 or qcom,sdhci-msm-v5.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220714091042.22287-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cards with 4k native sector size may only be read 4k-aligned,
accommodate for this in the single read recovery and use it.
Fixes: 81196976ed (mmc: block: Add blk-mq support)
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/cf4f316274c5474586d0d99b17db4a4c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v5.19rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v5.20.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add mmc_card_sd_combo() macro for sd combo type card and use the mmc_card_*
macro to simplify code instead of comparing card->type.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20220713033635.28432-2-sh043.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need runtime PM enabled early in probe before sdhci_setup_host() for
sdhci_omap_set_capabilities(). But on the first runtime resume we must
not call sdhci_runtime_resume_host() as sdhci_setup_host() has not been
called yet. Let's check for an initialized controller like we already do
for context restore to fix a lockdep warning.
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220622051215.34063-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In set_uhs_signaling, the DDR bit is being set by fully writing the MC1R
register.
This can lead to accidental erase of certain bits in this register.
Avoid this by doing a read-modify-write operation.
Fixes: d0918764c1 ("mmc: sdhci-of-at91: fix MMC_DDR_52 timing selection")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Karl Olsen <karl@micro-technic.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220630090926.15061-1-eugen.hristev@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD_ROCR_S18A is already defined and is used to check the rocr value, so
let's replace with already defined values for readability.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220706004840.24812-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we reset because of an error, we need to preserve values for the
clock frequency. Otherwise, glitches may be seen on the bus.
To achieve that, we introduce a 'preserve' parameter to the reset
function and the IP core specific reset callbacks to handle everything
accordingly.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220625131722.1397-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix typo's,
* difference -> different
* alignment -> aligned
While at it updated the comment to make it clear that Renesas SDHI DMAC
needs buffers to be 128-byte aligned.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of devm_reset_control_get_optional_exclusive() failure we returned
directly instead of jumping to the error path to roll back initialization.
This patch moves devm_reset_control_get_optional_exclusive() early in the
probe so that we have the reset handle prior to initialization of the
hardware.
Fixes: b4d86f37ea ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Callers of of_find_compatible_node() should drop the reference count
accordingly, so let's do that.
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220621065259.4079817-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If CONFIG_PM is not set.
make ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-, will be failed, like this:
drivers/mmc/host/sdhci-pci-gli.c:834:13: error: ‘gl9763e_set_low_power_negotiation’ defined but not used [-Werror=unused-function]
static void gl9763e_set_low_power_negotiation(struct sdhci_pci_slot *slot, bool enable)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[3]: *** [drivers/mmc/host/sdhci-pci-gli.o] Error 1
To fix building warning, wrap all related code with CONFIG_PM.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220619104712.125364-1-renzhijie2@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to flaws in hardware design, GL9763E takes long time to exit from L1
state. The I/O performance will suffer severe impact if it often enter and
exit L1 state during I/O requests.
To improve I/O read/write performance and take battery life into account,
let's turn on GL9763E L1 negotiation before entering runtime suspend and
turn off GL9763E L1 negotiation while executing runtime resume. That is to
say, GL9763E will not enter L1 state when executing I/O requests and enter
L1 state when PCIe bus idle.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20220613092907.2502-1-jason.lai@genesyslogic.com.tw
[Ulf: Improved the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns a few times along the lines of:
drivers/mmc/host/sdhci-brcmstb.c:302:6: warning: variable 'base_clk' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (res)
^~~
drivers/mmc/host/sdhci-brcmstb.c:376:24: note: uninitialized use occurs here
clk_disable_unprepare(base_clk);
^~~~~~~~
base_clk is used in the error path before it is initialized. Initialize
it to NULL, as clk_disable_unprepare() calls clk_disable() and
clk_unprepare(), which both handle NULL pointers gracefully.
Link: https://github.com/ClangBuiltLinux/linux/issues/1650
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220608152757.82529-1-nathan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220608090152.179395-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-6-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add debug fs entry error state to query eMMC and SD card errors statistics.
If any errors occurred in eMMC and SD card driver level then
err_state value will be set to 1.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-5-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-3-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-2-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/mmc/host/mxcmmc.c:1028:18: warning: cast to smaller integer type 'enum mxcmci_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 8223e885e7 ("mmc: mxc: Convert the driver to DT-only")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20220526010022.1163483-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() checks null pointer.
Fixes: ea35645a3c ("mmc: sdhci-of-esdhc: add support for signal voltage switch")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220523144255.10310-1-linmq006@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
