The pending == 2 case no longer exists in the driver so, we can use
ioat2_ring_pending() outside the lock to determine if there might be any
descriptors in the ring that the hardware has not seen.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We already disallow raid operations while DCA is globally enabled, so
having it locally enabled is a nop and confusing when reading the code.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes the COH 901 318 respect the scatter offset field by using
the sg_phys() rather than the sg_dma_address() so we get a pointer
to the actual data we want to send rather than the beginning of the
buffer. Also initialize the lli:s a bit more thoroughly.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes the COH 901 318 configure channel direction (to or from
device) dynamically, instead of being passed in from the platform
data. This was necessary in order to get the MMC/SD-card channel
bidirectional (all other channels on the U300 were either RX or
TX but this one was both). This also sets memcpy() alignent to
even 2^2 (32bit) boundaries, which makes the memcpy() stress tests
start working.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This removes the pointless irq counting for the COH 901 318, as
it turns out the hardware will only ever fire one IRQ for a linked
list anyway. In the process also a missing spinlock was introduced.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This centralize some spread-out initialization of descriptors into
one function and cleans up the error paths.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This cleans up the some debug code that was not working in the
COH 901 318 driver, adds some helpful comments and rearrange the
code a bit.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adds initial version of MPC512x DMA driver.
Only memory to memory transfers are currenly supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds Kconfig options for DEBUG and VERBOSE_DEBUG to the DMA
engine subsystem, I got tired of editing the Makefile manually
each time I want to debug things in here, modelled this on the
debug switches for other subsystems and works like a charm when
working on our DMA engines.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch extends the .device_terminate_all() method of the shdma driver
to return number of bytes transfered in the current descriptor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Provided platforms implement runtime PM, this disables the controller, when not
in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Separate SH DMA headers into ones, commonly used by both drivers, and ones,
specific to each of them. This will make the future development of the
dmaengine driver easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The shdma dmaengine driver currently uses numerous macros to support various
platforms, selected by ifdef's. Convert it to use platform device resources and
lists of channel descriptors to specify register locations, interrupt numbers
and other system-specific configuration variants. Unavoidably, we have to
simultaneously convert all shdma users to provide those resources.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Present DMA error ISR in shdma.c is bogus, it locks the system hard in multiple
ways. Fix it to abort all queued transactions on all channels on the affected
controller and giving submitters a chance to get a DMA_ERROR status for aborted
transactions. Afterwards further functionality is again possible without the
need to re-load the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just like commit ac5d73fc, we need to be careful to use 'src_cnt' as it
contains the fixed up number of xor sources (forced odd) to meet dmatest's
data verification scheme.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The number of PQ sources specified by module parameter "pq_sources"
is always forced odd to fit into dmatest's destination verificaton
scheme. But number of PQ sources and coefficients as passed to the
driver's prep_dma_pq() is not adjusted accordingly.
Fix it now to get correct PQ testing results in the case passed
"pq_sources" parameter is even.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fsl_dma_update_completed_cookie() appears to calculate the last completed
cookie incorrectly in the corner case where DMA on cookie 1 is in progress
just following a cookie wrap.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
[dan.j.williams@intel.com: fix an integer overflow warning with INT_MAX]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fsl_dma_tx_submit() only sets the cookie on the first descriptor of a
transaction. It should set the cookie on all.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add __percpu sparse annotations to places which didn't make it in one
of the previous patches. All converions are trivial.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Neil Brown <neilb@suse.de>
cohd_fin has already been verified not to be NULL, so the argument to
BUG_ON cannot be true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If submitting new buffer failed, a wrong descriptor gets completed and it
doesn't check, if a callback is at all defined, which can lead to an Oops. Fix
these bugs and make ipu_update_channel_buffer() void, because it never fails.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested to work with a SIU ASoC driver on sh7722 (migor).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both the original arch/sh/drivers/dma/dma-sh.c and the new SH dmaengine drivers
do not take into account bits 3:2 of the Transfer Size field in the CHCR
register, besides, bit-field defines set bit 2, but the mask only passes bits
1:0 through. TS_16BLK and TS_32BLK macros are bogus too. This patch fixes all
these issues for sh7722 and sh7724, other CPUs stay unchanged and might need to
be fixed too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Slave DMA functionality uses scatter-gather arrays for data transfers,
whereas memcpy just uses a single data buffer. This patch converts the
current memcpy implementation in shdma.c to use scatter-gather, making it
just a special case with one SG-element. This allows us to isolate
descriptor list manipulations and locking into one function, thus reducing
error chances.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In these cases the same statements are executed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
[dan.j.williams@intel.com: resolved conflict with recent fsldma updates]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix typo in ioat2_quiesce. check 'tmo' is zero, not 'end'. Also applies
to 2.6.32.3
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While debugging a dma driver I noticed a memleak after
unloading the driver module.
Caught by kmemleak.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix locking. Use two queues in the driver, one for pending transacions, and
one for transactions which are actually running on the hardware. Call
dma_run_dependencies() on descriptor cleanup so that the async_tx API works
correctly.
There are a number of places throughout the code where lists of descriptors
are freed in a loop. Create functions to handle this, and use them instead
of open-coding the loop each time.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The name fsl_chan seems too long, so it has been shortened to chan. There
are only a few places where the higher level "struct dma_chan *chan" name
conflicts. These have been changed to "struct dma_chan *dchan" instead.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The IRQ probing is needlessly complex. All off the 83xx device trees in
arch/powerpc/boot/dts/ specify 5 interrupts per DMA controller: one for the
controller, and one for each channel. These interrupts are all attached to
the same IRQ line.
This causes an interesting situation if two channels interrupt at the same
time. The per-controller handler will handle the first channel, and the
per-channel handler will handle the remaining channels.
Instead of this mess, we fix the bug in the per-controller handler, and
make it handle all channels that generated an interrupt. When a
per-controller handler is specified in the device tree, we prefer to use
the shared handler instead of the per-channel handler.
The 85xx/86xx controllers do not have a per-controller interrupt, and
instead use a per-channel interrupt. This behavior has not been changed.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fixes some errors in the cleanup paths of the OF subsystem, including
missing checks for ioremap failing. Also, some variables were renamed for
brevity.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Most functions in the standard library use "dst" as a parameter, rather
than "dest". This renames all use of "dest" to "dst" to match the usual
convention.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is the beginning of a cleanup which will change all instances of
"fsl_dma" to "fsldma" to match the name of the driver itself.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove some unused members from the fsldma data structures. A few trivial
uses of struct resource were converted to use the stack rather than keeping
the memory allocated for the lifetime of the driver.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some of the functions are written in a way where they use multiple reads
and writes where a single read/write pair could suffice. This shrinks the
kernel text size measurably, while making the functions easier to
understand.
add/remove: 0/0 grow/shrink: 1/4 up/down: 4/-196 (-192)
function old new delta
fsl_chan_set_request_count 120 124 +4
dma_halt 300 272 -28
fsl_chan_set_src_loop_size 208 156 -52
fsl_chan_set_dest_loop_size 208 156 -52
fsl_chan_xfer_ld_queue 500 436 -64
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
drivers/dma: Correct use after free
drivers/dma: drop unnecesary memset
ioat2,3: put channel hardware in known state at init
async_tx: expand async raid6 test to cover ioatdma corner case
ioat3: fix p-disabled q-continuation
sh: fix DMA driver's descriptor chaining and cookie assignment
dma: at_hdmac: correct incompatible type for argument 1 of 'spin_lock_bh'
Move the kfree after the iounmap that refers to the same structure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e;
identifier f;
iterator I;
statement S;
@@
*kfree(x);
... when != &x
when != x = e
when != I(x,...) S
*x->f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
memset of 0 is not needed after kzalloc
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
statement S;
@@
x = kzalloc(...);
if (x == NULL) S
... when != x
-memset(x,0,...);// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Put the ioat2 and ioat3 state machines in the halted state with all
errors cleared.
The ioat1 init path is not disturbed for stability, there are no
reported ioat1 initiaization issues.
Cc: <stable@kernel.org>
Reported-by: Roland Dreier <rdreier@cisco.com>
Tested-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When continuing a pq calculation the driver needs 3 extra sources. The
driver can perform a 3 source calculation with a single descriptor, but
needs an extended descriptor to process up to 8 sources in one
operation. However, in the p-disabled case only one extra source is
needed. When continuing a p-disabled operation there are occasions
(i.e. 0 < src_cnt % 8 < 3) where the tail operation does not need an
extended descriptor. Properly account for this fact otherwise invalid
'dmacount' values will be written to hardware usually causing the
channel to halt with 'invalid descriptor' errors.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The SH DMA driver wrongly assigns negative cookies to transfer descriptors,
also, its chaining of partial descriptors is broken. The latter problem is
usually invisible, because maximum transfer size per chunk is 16M, but if you
artificially set this limit lower, the driver fails. Since cookies are also
used in chunk management, both these problems are fixed in one patch. As side
effects a possible memory leak, when descriptors are prepared, but not
submitted, and multiple races have also been fixed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
ppc440spe-adma: adds updated ppc440spe adma driver
iop-adma.c: use resource_size()
dmaengine: clarify the meaning of the DMA_CTRL_ACK flag
sh: stylistic improvements for the DMA driver
dmaengine: fix dmatest to verify minimum transfer length and test buffer size
sh: DMA driver has to specify its alignment requirements
Add COH 901 318 DMA block driver v5
Correct a typo error in locking calls.
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
This patch adds new version of the PPC440SPe ADMA driver.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The size of the requested and ioremaped memory is off by 1.
Use resource_size() to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Transfers and the test buffer have to be at least align bytes long.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The SH DMA driver by default uses 32-byte transfers, in this mode buffers and
sizes have to be 32-byte aligned. Specifying this requirement also fixes Oopses
with dmatest.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ Error handling code following a kzalloc should free the allocated data.
2/ Report an error when no platform data is detected
Both problems fixed by moving the platform data check before the allocation,
and allows a goto to be killed.
Reported-by: Julia Lawall <julia@diku.dk>
Acked-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds support for the ST-Ericsson COH 901 318 DMA block,
found in the U300 series platforms. It registers a DMA slave for
device I/O and also a memcpy slave for memcpy.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The completion of a pq operation is notified with a null descriptor
appended to the end of the chain. This descriptor needs to be visible
to dma clients otherwise the client is precluded from ensuring all
operations are quiesced before freeing channel resources, i.e. due to
descriptor polling it may get the completion notification ahead of the
interrupt delivered by the null descriptor.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ioat3.2 does not support asynchronous error notifications which makes
the driver experience latencies when non-zero pq validate results are
expected. Provide a mechanism for turning off async_xor_val and
async_syndrome_val via Kconfig. This approach is generally useful for
any driver that specifies ASYNC_TX_DISABLE_CHANNEL_SWITCH and would like
to force the async_tx api to fall back to the synchronous path for
certain operations.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Error interrupts and error completions may cause channel hangs, so
poll the channel status register after a timeout.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
RAID operations cause a system hang on platforms with DCA
(Direct-Cache-Access) enabled. So turn off RAID capabilities in this
case.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add at91sam9g45 dependency to drivers/dma/Kconfig
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are cases where we can use this_cpu_ptr and as the result
of using this_cpu_ptr() we no longer need to determine the
currently executing cpu.
In those places no get/put_cpu combination is needed anymore.
The local cpu variable can be eliminated.
Preemption still needs to be disabled and enabled since the
modifications of the per cpu variables is not atomic. There may
be multiple per cpu variables modified and those must all
be from the same processor.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
cc: Eric Biederman <ebiederm@aristanetworks.com>
cc: Stephen Hemminger <shemminger@vyatta.com>
cc: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
drivers/dma/ioat/dma_v3.c: In function 'ioat3_prep_memset_lock':
drivers/dma/ioat/dma_v3.c:439: warning: 'fill' may be used uninitialized in this function
drivers/dma/ioat/dma_v3.c:437: warning: 'desc' may be used uninitialized in this function
drivers/dma/ioat/dma_v3.c: In function '__ioat3_prep_xor_lock':
drivers/dma/ioat/dma_v3.c:489: warning: 'xor' may be used uninitialized in this function
drivers/dma/ioat/dma_v3.c:486: warning: 'desc' may be used uninitialized in this function
drivers/dma/ioat/dma_v3.c: In function '__ioat3_prep_pq_lock':
drivers/dma/ioat/dma_v3.c:631: warning: 'pq' may be used uninitialized in this function
drivers/dma/ioat/dma_v3.c:628: warning: 'desc' may be used uninitialized in this function
gcc-4.0, unlike gcc-4.3, does not see that these variables are
initialized before use. Convert the descriptor loops to do-while make
this initialization apparent.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/ioat/dma_v2.c: In function 'ioat2_dma_prep_memcpy_lock':
drivers/dma/ioat/dma_v2.c:680: warning: 'hw' may be used uninitialized in this function
drivers/dma/ioat/dma_v2.c:681: warning: 'desc' may be used uninitialized in this function
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
With the addition of ioat_max_alloc_order it is not clear what the
maximum allocation order is, so document that in the modinfo. Also take
an opportunity to kill a stray semicolon.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch reworks platform driver power management code
for at_hdmac from legacy late/early callbacks to dev_pm_ops.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume_early() -> resume_noirq()
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
A new ring implementation and the addition of raid functionality
constitutes a bump in the driver major version number.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch enables DCA support on multiple-IOH/multiple-IIO architectures.
It modifies dca module by replacing single dca_providers list
with dca_domains list, each domain containing separate list of providers.
This approach lets dca driver manage multiple domains, i.e. sets of providers
and requesters mapped back to the same PCI root complex device.
The driver takes care to register each requester to a provider
from the same domain.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
This restriction prevented ASYNC_TX_DMA from being enabled on platform
configurations where DMA address conversion could not be performed in
place on the stack. Since commit 04ce9ab3 ("async_xor: permit callers
to pass in a 'dma/page scribble' region") the async_tx api now either
uses a caller provided 'scribble' buffer, or performs the conversion in
place when sizeof(dma_addr_t) <= sizeof(struct page *).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This supported all DMA channels, and it was tested in SH7722,
SH7780, SH7785 and SH7763.
This can not use with SH DMA API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams wrote:
... DMA-slave clients request specific channels and know the hardware
details at a low level, so it should not be too high an expectation to
push dma mapping responsibility to the client.
Also this patch includes DMA_COMPL_{SRC,DEST}_UNMAP_SINGLE support for
dw_dmac driver.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the DMA_SLAVE capability of the DMAEngine API to copy/from a
scatterlist into an arbitrary list of hardware address/length pairs.
This allows a single DMA transaction to copy data from several different
devices into a scatterlist at the same time.
This also adds support to enable some controller-specific features such as
external start and external pause for a DMA transaction.
[dan.j.williams@intel.com: rebased on tx_list movement]
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When using the Freescale DMA controller in external control mode, both the
request count and external pause bits need to be setup correctly. This was
being done with the same function.
The 83xx controller lacks the external pause feature, but has a similar
feature called external start. This feature requires that the request count
bits be setup correctly.
Split the function into two parts, to make it possible to use the external
start feature on the 83xx controller.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All the necessary fields for handling an ioat2,3 ring entry can fit into
one cacheline. Move ->len prior to ->txd in struct ioat_ring_ent, and
move allocation of these entries to a hw-cache-aligned kmem cache to
reduce the number of cachelines dirtied for descriptor management.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The tx_list attribute of struct dma_async_tx_descriptor is common to
most, but not all dma driver implementations. None of the upper level
code (dmaengine/async_tx) uses it, so allow drivers to implement it
locally if they need it. This saves sizeof(struct list_head) bytes for
drivers that do not manage descriptors with a linked list (e.g.: ioatdma
v2,3).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop txx9dmac's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop at_hdmac's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop mv_xor's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop ioatdma's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop iop-adma's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop fsldma's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop dw_dmac's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Trivial cleanup to make the PCI ID table easier to read.
[dan.j.williams@intel.com: extended to v3.2 devices]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ioatdma module is missing aliases for the PCI devices it supports,
so it is not autoloaded on boot. Add a MODULE_DEVICE_TABLE() to get
these aliases.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The cleanup routine for the raid cases imposes extra checks for handling
raid descriptors and extended descriptors. If the channel does not
support raid it can avoid this extra overhead by using the ioat2 cleanup
path.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
