The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
For the PCIe-IDIO-24 series of devices, the following BARs are
available:
BAR[0]: memory mapped PEX8311
BAR[1]: I/O mapped PEX8311
BAR[2]: I/O mapped card registers
There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS
lines (which may be configured for either output or input). The GPIO
lines are exposed by the following card registers:
Base +0x0-0x2 (Read/Write): FET Outputs
Base +0xB (Read/Write): TTL/CMOS
Base +0x4-0x6 (Read): Isolated Inputs
Base +0x7 (Read): TTL/CMOS
In order for the device to support interrupts, the PLX PEX8311 internal
PCI wire interrupt and local interrupt input must first be enabled.
The following card registers for Change-Of-State may be used:
Base +0x8-0xA (Read): COS Status Inputs
Base +0x8-0xA (Write): COS Clear Inputs
Base +0xB (Read): COS Status TTL/CMOS
Base +0xB (Write): COS Clear TTL/CMOS
Base +0xE (Read/Write): COS Enable
The COS Enable register is used to enable/disable interrupts and
configure the interrupt levels; each bit maps to a group of eight inputs
as described below:
Bit 0: IRQ EN Rising Edge IN0-7
Bit 1: IRQ EN Rising Edge IN8-15
Bit 2: IRQ EN Rising Edge IN16-23
Bit 3: IRQ EN Rising Edge TTL0-7
Bit 4: IRQ EN Falling Edge IN0-7
Bit 5: IRQ EN Falling Edge IN8-15
Bit 6: IRQ EN Falling Edge IN16-23
Bit 7: IRQ EN Falling Edge TTL0-7
An interrupt is asserted when a change-of-state matching the interrupt
level configuration respective for a particular group of eight inputs
with enabled COS is detected.
The COS Status registers may be read to determine which inputs have
changed; if interrupts were enabled, an IRQ will be generated for the
set bits in these registers. Writing the value read from the COS Status
register back to the respective COS Clear register will clear just those
interrupts.
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
All idio-16 library consumers have migrated to the new interface
leveraging the gpio-regmap API. Legacy interface functions and code are
removed as no longer needed.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/651cff1cc3eb57b455a8048121cf6a4d4367f018.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the pci-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/5ba5405c64aca984d5cf3bdbdffa04c325e5a147.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the 104-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1f24a1f18c9a9daa4983713e0a5b53e838d624a8.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
By leveraging the regmap API, the idio-16 library is reduced to simply a
devm_idio_16_regmap_register() function and a configuration structure
struct idio_16_regmap_config.
Legacy functions and code will be removed once all consumers have
migrated to the new idio-16 library interface.
For IDIO-16 devices we have the following IRQ registers:
Base Address +1 (Write): Clear Interrupt
Base Address +2 (Read): Enable Interrupt
Base Address +2 (Write): Disable Interrupt
An interrupt is asserted whenever a change-of-state is detected on any
of the inputs. Any write to 0x2 will disable interrupts, while any read
will enable interrupts. Interrupts are cleared by a write to 0x1.
For 104-IDIO-16 devices, there is no IRQ status register, so software
has to assume that if an interrupt is raised then it was for the
104-IDIO-16 device.
For PCI-IDIO-16 devices, there is an additional IRQ register:
Base Address +6 (Read): Interrupt Status
Interrupt status can be read from 0x6 where bit 2 set indicates that an
IRQ has been generated.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b45081958ab53dfa697f4a8b15f1bfba46718068.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When comparing strings passed to us from configfs, we can pass the page
argument directly to sysfs_streq() and avoid manual string trimming.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here, and __maybe_unused can also be removed.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here, and __maybe_unused can also be removed.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use CONFIG_OF
and of_match_ptr() here, we remove them all.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
CONFIG_OF and of_match_ptr() here, so we remove them all.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here. We remove both CONFIG_OF and of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver depends on CONFIG_OF, so it is not necessary to use
of_match_ptr() here.
Even for drivers that do not depend on CONFIG_OF, it's almost always
better to leave out the of_match_ptr(), since the only thing it can
possibly do is to save a few bytes of .text if a driver can be used both
with and without it. Hence we remove of_match_ptr().
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Since commit a85a6c86c2 ("driver core: platform: Clarify that IRQ 0
is invalid"), there is no possible for platform_get_irq() to return 0.
And the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call is not required because no counterpart
platform_get_drvdata() call is present to leverage the private data of
the driver.
Since the private data is confined to this driver file, external access
is not feasible.
The use of this function appears redundant in the current context of the
driver's implementation.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call, to access the private data of the driver.
Also, the private data is defined in this driver, so there is no risk of
it being accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() call was never used, ever since the driver was
originally added.
It looks like this copy+paste left-over. Possibly the author copied from a
driver that had this line, but also had a remove hook.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() isn't needed for anything. The function is a
simple setter that doesn't change anything in the code. That is because
there isn't a get function and since it has no dependencies it can be
removed.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() was needed when the driver had an explicit
remove function.
That function got removed a while back, so we don't need to keep a pointer
(on 'dev->driver_data') for the private data of the driver anymore.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() was needed when the driver had an explicit
remove function.
That function got removed a while back, so we don't need to keep a pointer
(on 'dev->driver_data') for the private data of the driver anymore.
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to call the dev_err_probe() function directly to print
a custom message when handling an error from platform_get_irq() function as
it is going to display an appropriate error message in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The DS4520 is a 9-bit nonvolatile (NV) I/O expander.
It offers users a digitally programmable alternative
to hardware jumpers and mechanical switches that are
being used to control digital logic node.
Signed-off-by: Okan Sahin <okan.sahin@analog.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to call the dev_err_probe() function directly to print
a custom message when handling an error from platform_get_irq() function as
it is going to display an appropriate error message in case of a failure.
And the code to handle bank->irq = 0 is redundant because
platform_get_irq() do not return 0.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The 104-DIO-48E features an 8254 Counter/Timer chip providing three
counter/timers which can be used for frequency measurement, frequency
output, pulse width modulation, pulse width measurement, event count,
etc. The counter/timers use the same addresses as PPI 0 (addresses 0x0
to 0x3), so a raw_spinlock_t is used to synchronize operations between
the two regmap mappings to prevent clobbering.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Driver is so simple, yet there was a room for mistakes.
Reduce their appearance in the future by enabling COMPILE_TEST
option.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Replace the GPLv2 boilerplate text with a nice and short
SPDX header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We have a temporary variable to keep pointer to struct device.
Utilise it inside the ->probe() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is nothing in the driver that requires OF APIs,
make the driver OF independent.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Fix English spelling and grammar in the comments.
While at it, fix the MODULE_AUTHOR() email address format.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/r/65b4ac1a-1128-6e2a-92c0-9bbcca4b760a@infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add missing platform_device.h that used to be implied by of_device.h.
While at it, sort headers alphabetically for better maintenance.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: e91d0f05e6 ("gpio: Explicitly include correct DT includes")
Closes: https://lore.kernel.org/r/65b4ac1a-1128-6e2a-92c0-9bbcca4b760a@infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This can reduce the kernel image size in multiplatform configurations.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Do not parse the devicetree again when the data is already available
from the IRQ subsystem. This follows the example of the ThunderX and
X-Gene GPIO drivers. The ngpio check is needed to avoid a possible
out-of-bounds read.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
of_irq_count(), or eqivalently platform_irq_count(), simply looks up
successively-numbered IRQs until that fails. Since this driver needs to
look up each IRQ anyway to get its virq number, use that existing loop
to count the IRQs at the same time.
The check against SIFIVE_GPIO_MAX functioned as a bounds check for
chip->irq_number. That is now handled by the loop condition.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to convert dev->of_node back to a fwnode_handle.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
If CONFIG_PM=n (e.g. m68k/allmodconfig):
drivers/gpio/gpio-mxc.c:612:12: error: ‘mxc_gpio_runtime_resume’ defined but not used [-Werror=unused-function]
612 | static int mxc_gpio_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpio/gpio-mxc.c:602:12: error: ‘mxc_gpio_runtime_suspend’ defined but not used [-Werror=unused-function]
602 | static int mxc_gpio_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Fix this by using the non-SET *_PM_OPS to configure the dev_pm_ops
callbacks, and by wrapping the driver.pm initializer insider pm_ptr().
As NOIRQ_SYSTEM_SLEEP_PM_OPS() uses pm_sleep_ptr() internally, the
__maybe_unused annotations for the noirq callbacks are no longer needed,
and can be removed.
Fixes: 3283d820dc ("gpio: mxc: add runtime pm support")
Reported-by: noreply@ellerman.id.au
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
While here update copyright and module author.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The pdev member is assigned and not used, drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The platform_set_drvdata() call was never used, ever since the driver was
originally added.
It looks like this copy+paste left-over. Possibly the author copied from a
driver that had this line, but also had a remove hook.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
