With PMIC node in place, add the correct regulators for eMMC.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With driver support in place add the PMIC node and remove the
fixed-regulators for rails provided by PMIC.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the DT to match newest Data Modul i.MX8M Mini eDM SBC rev.A01
board which implements PHY changes. Keep some of the rev.900 PHY node
in the DT so that a DTO can be used to support rev.900 boards easily.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ISP supports both CSI and parallel interfaces, where port 0
corresponds to the former and port 1 corresponds to the latter. Since
the i.MX8MP's ISPs are connected by the parallel interface to the CSI
receiver, set them both to port 1.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add fixed regulator VCC_5V_SW based on the phyBOARD-Pollux schematics
to reflect the connectivity on the phyBOARD-Pollux-i.MX8MP.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SD-Card property for the bus IO power from the PMIC.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add fixed regulator VDD_IO (3.3v) based on the SoM schematics to reflect
the connectivity on the phyCORE-i.MX8MP.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DT nodes for the MIPI CSI-2 receivers (MIPI_CSI) configure the
CAM1_PIX and CAM2_PIX clocks to 266 MHz through the assigned-clock-rates
property, and report that frequency in the clock-frequency property. The
i.MX8MP reference manual and datasheet list 266 MHz as a nominal
frequency when using both CSI-2 receivers, so all looks normal.
In reality, the clock is actually set to 250 MHz, as the selected
parent, IMX8MP_SYS_PLL2_1000M, has a 1/4 output that is selected as the
closest frequency to 266 MHz. This doesn't break operation of the
device, but is clearly misleading.
Clarify the clock configuration by selecting the IMX8MP_SYS_PLL2_250M
parent, dropping the redundant assigned-clock-rates, and setting
clock-frequency to 250 MHz. This doesn't cause any functional change.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the Kontron Electronics OSM-S i.MX93 SoM
and the matching baseboard BL i.MX93.
The SoM hardware complies to the Open Standard Module (OSM) 1.1
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The interrupt pin of the PHY is connected to the GPIO expander, configure
it accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unused property num-viewport to fix dtbs warnings.
arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dtb: pcie@3400000: Unevaluated properties are not allowed ('num-viewport' was unexpected)
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1012a-oxalis.dtb: pcie@3400000: Unevaluated properties are not allowed ('num-viewport' was unexpected)
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Animesh Agarwal <animeshagarwal28@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for TPM for phyBOARD Pollux.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX93 11x11 EVK has a ST LSM6DSO connected to I2C, which a is 6-axis
IMU (inertial measurement unit = accelerometer & gyroscope). So add the
missing parts to the DTS file.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to microchip,usb2514.yaml, the node name must contain
'usb-hub'.
Change it accordingly to fix the following dt-schema warning:
hub@1: $nodename:0: 'hub@1' does not match '^usb(@.*)?'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to adi,adv7533.yaml, the order for the reg and reg-names entries
must be: main, edid, cec, and packet.
Fix it accordingly to remove the following dt-schema warnings:
hdmi@3d: reg-names:1: 'edid' was expected
hdmi@3d: reg-names:2: 'cec' was expected
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove compatible string in overlay file to fix below warning:
gw,imx8mp-gw74xx' is not one of ['fsl,ls1043a-rdb', 'fsl,ls1043a-qds']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove #clock-cells for sai3 because sai3 is not clock controller to fix
below warning:
/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dtb: sai@30c30000: Unevaluated properties are not allowed ('#clock-cells' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add #address-cells and #size-cells for gsc@20 to fix below warning:
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dtb: gsc@20: '#address-cells' is a required propert
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move reboot node under syscon and change compatible string to
fsl,ls1028a-rstcr because it is exactly same as ls1028a.
Fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dtb:
/syscon@1e60000: failed to match any schema with compatible: ['fsl,ls2080a-rstcr', 'syscon']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc http://devicetree.org/schemas/spi/fsl,dspi.yaml
and driver drivers/spi/spi-fsl-dspi.c, default is little-endian, should
use big-endian for big-endian system. Remove 'little-endian' to fix below
warning:
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dtb: spi@2100000: Unevaluated properties are not allowed ('little-endian' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add native HDMI audio to Verdin iMX8MP and all its carriers boards.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the flexcan[1..5] nodes for imx95.
Reviewed-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DDR Perf Monitor for i.MX95.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
fsl,ls2080a-pcie actual is the same as fsl,ls2085a-pcie. Only keep one is
enough, so remove "fsl,ls2085a-pcie" to fix below warnings.
arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dtb: pcie@3400000: compatible: ['fsl,ls2080a-pcie', 'fsl,ls2085a-pcie'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove undocumented compatible string fsl,ls-pcie-ep to fix below
CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dtb: pcie_ep@3400000: compatible: ['fsl,ls1046a-pcie-ep', 'fsl,ls-pcie-ep'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie-ep.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc fsl,ddr.yaml, big-endian is default setting. So
remove it to fix below CHECK_DTBS warnings.
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: memory-controller@1080000: 'big-endian' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,ddr.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc fsl,esdhc.yaml, the default endian mode is
big-endian. So remove big-endian property to fix below CHECK_DTBS warnings:
arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: mmc@1560000: Unevaluated properties are not allowed ('big-endian' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/fsl,esdhc.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add msi-cell = <1> for GIC ITS. msi-parent have to be kept because it is
checked by U-Boot due to historical reasons to fix up msi-map.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dtb: interrupt-controller@6000000: msi-controller@6020000: '#msi-cells' is a required property
from schema $id: http://devicetree.org/schemas/interrupt-controller/arm,gic-v3.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add platform specific compatiable string 'fsl,ls1028-reset' for syscon and
move reboot node under reset syscon node to fix below warning.
syscon@1e60000: compatible: 'anyOf' conditional failed, one must be fixed:
['syscon'] is too short
'syscon' is not one of ['al,alpine-sysfabric-service', ...
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change node name 'uqe' to 'uqe-bus'.
Remove #address-cells and #size-cells for nodes, which have not child node.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: si@700: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: siram@1000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: $nodename:0: 'uqe@2400000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: uqe@2400000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'qeic@80', 'ucc@2000', 'ucc@2200' were unexpected)
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: qeic@80: '#address-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ic.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: si@700: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-si.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: siram@1000: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-siram.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pcsphy-handle already deprecated according to binding fsl,fman-dtsec.yaml.
Add new common pcs-handle at dts and fix below CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: fman@1a00000: ethernet@e0000: 'pcs-handle' is a dependency of 'pcs-handle-names'
from schema $id: http://devicetree.org/schemas/net/fsl,fman.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Invoke power-domain.yaml if node name as 'power-control'.
Rcpm actually are not power domain controller. It just control wakeup
capability. So rename it as wakeup-control. Fix below CHECK_DTBS warning.
power-controller@1ee2140: '#power-domain-cells' is a required property
from schema $id: http://devicetree.org/schemas/power/power-domain.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The node name 'aux-bus' is special word. It invokes dp-aux-bus.yaml binding
check. Simple change to 'bus' to fix below warning.
aux-bus: '#address-cells', '#size-cells', 'compatible', 'dma-ranges', 'ranges', 'sata@3200000', 'usb@2f00000', 'usb@3000000', 'usb@3100000' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/dp-aux-bus.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDIO frequency was limited to workaround some instabilities, however it
turned out that the instability had nothing to do with the speed but was
because of an issue with the USDHC IP that was fixed in
commit 52e4c32bae ("mmc: sdhci-esdhc-imx: only enable DAT[0] and CMD line
auto tuning for SDIO device").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX93 features two Cortex-A55 cores with per core L1 Instruction
cache size 32KB, L1 data cache size 32KB, per core L2 cache 64KB, and
unified 256KB L3 cache.
Add the cache info to remove cacheinfo warnings at boot:
"cacheinfo: Unable to detect cache hierarchy for CPU 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DMA configurations for LPSPI nodes on i.MX8QX/QM/DXL.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM microphone
and convert the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add #sound-dai-cells property for audio cpu dai modules
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pinctrl node in the device tree in order to enable the
S32G2/S32G3 pinctrl driver to probe.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- disable PU/PD if already done with external resistors
- do not configure Schmitt Trigger for outputs
- do not configure DSE / FSEL for inputs
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
100kHz is only needed for the USB Hub TUSB8041. But as this device is not
connected by default, the speed can be increased.
The other busses don't have any 100kHz only devices attached.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These properties are required by i2c-controller.yaml bindings.
Add them on SoC level, rather than on board level.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Neither the imx8dxl-evk or imx8qm-mek have a Rohm DAC on them as far as
I can tell from online documentation, and they certainly do not have a
dh2228fv, as this device does not actually exist! Remove the DAC nodes
from the devicetrees as it is not acceptable to pretend to have a device
on a board in order to bind the spidev driver in Linux.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Micro SD cards can't be physically write-protected like full-sized
cards. Disable this feature in device-tree to get rid of the kernel
warning:
"host does not support reading read-only switch, assuming write-enable"
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a devicetree overlay to disable ethernet for boards where it is not
populated.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
NXP S32G2/S32G3 SoC based platforms do not
use a pin for SD-Card write protection used by
the uSDHC controller.
Hence, adding 'disable-wp' usdhc device-tree property in order to fix
observed warnings on SD boot as the following:
"host does not support reading read-only switch, assuming write-enable"
Signed-off-by: Ciprian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to describe the compatible string inside
a dtso file.
dt-schema produces super verbose warnings about that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Parthiban Nallathambi <parthiban@linumiz.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to describe the compatible string inside
a dtso file.
dt-schema produces super verbose warnings about that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add thermal_zone label because it may be overwrite by board level dts file.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add flexspi support.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sai1, sai2. Add i2c4 and wm8962 and other dependent nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sai[1..6], NXP Audio Transceiver (XCVR) Controller and MICFIL Digital
Audio Interface (MICFIL).
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add eDMA1, eDMA2 and eDMA3 support for iMX95.
Add dmas and dma-names for each peripheral, which use eDMA.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the board device tree with sdhc1/2, cm33, flexcan, mu, lpuart1,
lpi2c1/2, usb enabled and etc, which to support the i.MX 93 14x14
Evaluation kit that is an automotive market oriented evaluation board
with i.MX 93 application processors in a 14x14mm package.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'#address-cells' and '#size-cells' are already included in soc device tree,
no need add them in board device tree.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For Platform to Agent(p2a) notification, i.MX95 System Manager(SM)
firmware requires a reply communication. So add mailbox channel for
p2a reply communication.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* Support for NUMA (via SRAT and SLIT), console output (via SPCR), and
cache info (via PPTT) on ACPI-based systems.
* The trap entry/exit code no longer breaks the return address stack
predictor on many systems, which results in an improvement to trap
latency.
* Support for HAVE_ARCH_STACKLEAK.
* The sv39 linear map has been extended to support 128GiB mappings.
* The frequency of the mtime CSR is now visible via hwprobe.
-----BEGIN PGP SIGNATURE-----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=zeUn
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.11-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for NUMA (via SRAT and SLIT), console output (via SPCR), and
cache info (via PPTT) on ACPI-based systems.
- The trap entry/exit code no longer breaks the return address stack
predictor on many systems, which results in an improvement to trap
latency.
- Support for HAVE_ARCH_STACKLEAK.
- The sv39 linear map has been extended to support 128GiB mappings.
- The frequency of the mtime CSR is now visible via hwprobe.
* tag 'riscv-for-linus-6.11-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (21 commits)
RISC-V: Provide the frequency of time CSR via hwprobe
riscv: Extend sv39 linear mapping max size to 128G
riscv: enable HAVE_ARCH_STACKLEAK
riscv: signal: Remove unlikely() from WARN_ON() condition
riscv: Improve exception and system call latency
RISC-V: Select ACPI PPTT drivers
riscv: cacheinfo: initialize cacheinfo's level and type from ACPI PPTT
riscv: cacheinfo: remove the useless input parameter (node) of ci_leaf_init()
RISC-V: ACPI: Enable SPCR table for console output on RISC-V
riscv: boot: remove duplicated targets line
trace: riscv: Remove deprecated kprobe on ftrace support
riscv: cpufeature: Extract common elements from extension checking
riscv: Introduce vendor variants of extension helpers
riscv: Add vendor extensions to /proc/cpuinfo
riscv: Extend cpufeature.c to detect vendor extensions
RISC-V: run savedefconfig for defconfig
RISC-V: hwprobe: sort EXT_KEY()s in hwprobe_isa_ext0() alphabetically
ACPI: NUMA: replace pr_info with pr_debug in arch_acpi_numa_init
ACPI: NUMA: change the ACPI_NUMA to a hidden option
ACPI: NUMA: Add handler for SRAT RINTC affinity structure
...
- Remove some redundant Kconfig conditionals
- Fix string output in ptrace selftest
- Fix fast GUP crashes in some page-table configurations
- Remove obsolete linker option when building the vDSO
- Fix some sysreg field definitions for the GIC
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmaiSAMQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNJ8PB/9lyDbJ+qTNwECGKtz+vOAbronZncJy4yzd
ElPRNeQ+B7QqrrYZM2TCrz6/ppeKXp0OurwNk9vKBqzrCfy/D6kKXWfcOYqeWlyI
C2NImLHZgC6pIRwF3GlJ/E0VDtf/wQsJoWk7ikVssPtyIWOufafaB53FRacc1vnf
bmEpcdXox+FsTG4q8YhBE6DZnqqQTnm7MvAt4wgskk6tTyKj/FuQmSk50ZW22oXb
G2UOZxhYZV7IIXlRaClsY/iv62pTfMYlqDAvZeH81aiol/vfYXVFSeca5Mca67Ji
P1o8HPd++hTw9WVyCrrbSGcZ/XNs96yTmahJWM+eneiV7OzKxj4v
=Mr4K
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The usual summary below, but the main fix is for the fast GUP lockless
page-table walk when we have a combination of compile-time and
run-time folding of the p4d and the pud respectively.
- Remove some redundant Kconfig conditionals
- Fix string output in ptrace selftest
- Fix fast GUP crashes in some page-table configurations
- Remove obsolete linker option when building the vDSO
- Fix some sysreg field definitions for the GIC"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Fix lockless walks with static and dynamic page-table folding
arm64/sysreg: Correct the values for GICv4.1
arm64/vdso: Remove --hash-style=sysv
kselftest: missing arg in ptrace.c
arm64/Kconfig: Remove redundant 'if HAVE_FUNCTION_GRAPH_TRACER'
arm64: remove redundant 'if HAVE_ARCH_KASAN' in Kconfig
On arm64 we build compressed images, but "make install" by default will
install the old non-compressed one. To actually get the compressed
image install, you need to use "make zinstall", which is not the usual
way to install a kernel.
Which may not sound like much of an issue, but when you deal with
multiple architectures (and years of your fingers knowing the regular
"make install" incantation), this inconsistency is pretty annoying.
But as Will Deacon says:
"Sadly, bootloaders being as top quality as you might expect, I don't
think we're in a position to rely on decompressor support across the
board. Our Image.gz is literally just that -- we don't have a built-in
decompressor (nor do I think we want to rush into that again after the
fun we had on arm32) and the recent EFI zboot support solves that
problem for platforms using EFI.
Changing the default 'install' target terrifies me. There are bound to
be folks with embedded boards who've scripted this and we could really
ruin their day if we quietly give them a compressed kernel that their
bootloader doesn't know how to handle :/"
So make this conditional on a new "COMPRESSED_INSTALL" option.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lina reports random oopsen originating from the fast GUP code when
16K pages are used with 4-level page-tables, the fourth level being
folded at runtime due to lack of LPA2.
In this configuration, the generic implementation of
p4d_offset_lockless() will return a 'p4d_t *' corresponding to the
'pgd_t' allocated on the stack of the caller, gup_fast_pgd_range().
This is normally fine, but when the fourth level of page-table is folded
at runtime, pud_offset_lockless() will offset from the address of the
'p4d_t' to calculate the address of the PUD in the same page-table page.
This results in a stray stack read when the 'p4d_t' has been allocated
on the stack and can send the walker into the weeds.
Fix the problem by providing our own definition of p4d_offset_lockless()
when CONFIG_PGTABLE_LEVELS <= 4 which returns the real page-table
pointer rather than the address of the local stack variable.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/50360968-13fb-4e6f-8f52-1725b3177215@asahilina.net
Fixes: 0dd4f60a2c ("arm64: mm: Add support for folding PUDs at runtime")
Reported-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20240725090345.28461-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
const qualify the struct ctl_table argument in the proc_handler function
signatures. This is a prerequisite to moving the static ctl_table
structs into .rodata data which will ensure that proc_handler function
pointers cannot be modified.
This patch has been generated by the following coccinelle script:
```
virtual patch
@r1@
identifier ctl, write, buffer, lenp, ppos;
identifier func !~ "appldata_(timer|interval)_handler|sched_(rt|rr)_handler|rds_tcp_skbuf_handler|proc_sctp_do_(hmac_alg|rto_min|rto_max|udp_port|alpha_beta|auth|probe_interval)";
@@
int func(
- struct ctl_table *ctl
+ const struct ctl_table *ctl
,int write, void *buffer, size_t *lenp, loff_t *ppos);
@r2@
identifier func, ctl, write, buffer, lenp, ppos;
@@
int func(
- struct ctl_table *ctl
+ const struct ctl_table *ctl
,int write, void *buffer, size_t *lenp, loff_t *ppos)
{ ... }
@r3@
identifier func;
@@
int func(
- struct ctl_table *
+ const struct ctl_table *
,int , void *, size_t *, loff_t *);
@r4@
identifier func, ctl;
@@
int func(
- struct ctl_table *ctl
+ const struct ctl_table *ctl
,int , void *, size_t *, loff_t *);
@r5@
identifier func, write, buffer, lenp, ppos;
@@
int func(
- struct ctl_table *
+ const struct ctl_table *
,int write, void *buffer, size_t *lenp, loff_t *ppos);
```
* Code formatting was adjusted in xfs_sysctl.c to comply with code
conventions. The xfs_stats_clear_proc_handler,
xfs_panic_mask_proc_handler and xfs_deprecated_dointvec_minmax where
adjusted.
* The ctl_table argument in proc_watchdog_common was const qualified.
This is called from a proc_handler itself and is calling back into
another proc_handler, making it necessary to change it as part of the
proc_handler migration.
Co-developed-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Co-developed-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Joel Granados <j.granados@samsung.com>
- Remove tristate choice support from Kconfig
- Stop using the PROVIDE() directive in the linker script
- Reduce the number of links for the combination of CONFIG_DEBUG_INFO_BTF
and CONFIG_KALLSYMS
- Enable the warning for symbol reference to .exit.* sections by default
- Fix warnings in RPM package builds
- Improve scripts/make_fit.py to generate a FIT image with separate base
DTB and overlays
- Improve choice value calculation in Kconfig
- Fix conditional prompt behavior in choice in Kconfig
- Remove support for the uncommon EMAIL environment variable in Debian
package builds
- Remove support for the uncommon "name <email>" form for the DEBEMAIL
environment variable
- Raise the minimum supported GNU Make version to 4.0
- Remove stale code for the absolute kallsyms
- Move header files commonly used for host programs to scripts/include/
- Introduce the pacman-pkg target to generate a pacman package used in
Arch Linux
- Clean up Kconfig
-----BEGIN PGP SIGNATURE-----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=BYu7
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Remove tristate choice support from Kconfig
- Stop using the PROVIDE() directive in the linker script
- Reduce the number of links for the combination of CONFIG_KALLSYMS and
CONFIG_DEBUG_INFO_BTF
- Enable the warning for symbol reference to .exit.* sections by
default
- Fix warnings in RPM package builds
- Improve scripts/make_fit.py to generate a FIT image with separate
base DTB and overlays
- Improve choice value calculation in Kconfig
- Fix conditional prompt behavior in choice in Kconfig
- Remove support for the uncommon EMAIL environment variable in Debian
package builds
- Remove support for the uncommon "name <email>" form for the DEBEMAIL
environment variable
- Raise the minimum supported GNU Make version to 4.0
- Remove stale code for the absolute kallsyms
- Move header files commonly used for host programs to scripts/include/
- Introduce the pacman-pkg target to generate a pacman package used in
Arch Linux
- Clean up Kconfig
* tag 'kbuild-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (65 commits)
kbuild: doc: gcc to CC change
kallsyms: change sym_entry::percpu_absolute to bool type
kallsyms: unify seq and start_pos fields of struct sym_entry
kallsyms: add more original symbol type/name in comment lines
kallsyms: use \t instead of a tab in printf()
kallsyms: avoid repeated calculation of array size for markers
kbuild: add script and target to generate pacman package
modpost: use generic macros for hash table implementation
kbuild: move some helper headers from scripts/kconfig/ to scripts/include/
Makefile: add comment to discourage tools/* addition for kernel builds
kbuild: clean up scripts/remove-stale-files
kconfig: recursive checks drop file/lineno
kbuild: rpm-pkg: introduce a simple changelog section for kernel.spec
kallsyms: get rid of code for absolute kallsyms
kbuild: Create INSTALL_PATH directory if it does not exist
kbuild: Abort make on install failures
kconfig: remove 'e1' and 'e2' macros from expression deduplication
kconfig: remove SYMBOL_CHOICEVAL flag
kconfig: add const qualifiers to several function arguments
kconfig: call expr_eliminate_yn() at least once in expr_eliminate_dups()
...
Currently, sysreg has value as 0b0010 for the presence of GICv4.1 in
ID_PFR1_EL1 and ID_AA64PFR0_EL1, instead of 0b0011 as per ARM ARM.
Hence, correct them to reflect ARM ARM.
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240718215532.616447-1-rananta@google.com
Signed-off-by: Will Deacon <will@kernel.org>
glibc added support for .gnu.hash in 2006 and .hash has been obsoleted
for more than one decade in many Linux distributions. Using
--hash-style=sysv might imply unaddressed issues and confuse readers.
Just drop the option and rely on the linker default, which is likely
"both", or "gnu" when the distribution really wants to eliminate sysv
hash overhead.
Similar to commit 6b7e26547f ("x86/vdso: Emit a GNU hash").
Signed-off-by: Fangrui Song <maskray@google.com>
Link: https://lore.kernel.org/r/20240718173423.1574395-1-maskray@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Since the commit 819e50e25d ("arm64: Add ftrace support"),
HAVE_FUNCTION_GRAPH_TRACER has always been enabled. Although a subsequent
commit 3646970322 ("arm64: ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL")
redundantly added check on HAVE_FUNCTION_GRAPH_TRACER, while enabling the
config HAVE_FUNCTION_GRAPH_RETVAL. Let's just drop this redundant check.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240716050915.2657694-1-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
- Core:
- Provide a new mechanism to create interrupt domains. The existing
interfaces have already too many parameters and it's a pain to expand
any of this for new required functionality.
The new function takes a pointer to a data structure as argument. The
data structure combines all existing parameters and allows for easy
extension.
The first extension for this is to handle the instantiation of
generic interrupt chips at the core level and to allow drivers to
provide extra init/exit callbacks.
This is necessary to do the full interrupt chip initialization before
the new domain is published, so that concurrent usage sites won't see
a half initialized interrupt domain. Similar problems exist on
teardown.
This has turned out to be a real problem due to the deferred and
parallel probing which was added in recent years.
Handling this at the core level allows to remove quite some accrued
boilerplate code in existing drivers and avoids horrible workarounds
at the driver level.
- The usual small improvements all over the place
- Drivers
- Add support for LAN966x OIC and RZ/Five SoC
- Split the STM ExtI driver into a microcontroller and a SMP version to
allow building the latter as a module for multi-platform kernels.
- Enable MSI support for Armada 370XP on platforms which do not support
IPIs.
- The usual small fixes and enhancements all over the place.
-----BEGIN PGP SIGNATURE-----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=QCRH
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2024-07-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Core:
- Provide a new mechanism to create interrupt domains. The existing
interfaces have already too many parameters and it's a pain to
expand any of this for new required functionality.
The new function takes a pointer to a data structure as argument.
The data structure combines all existing parameters and allows for
easy extension.
The first extension for this is to handle the instantiation of
generic interrupt chips at the core level and to allow drivers to
provide extra init/exit callbacks.
This is necessary to do the full interrupt chip initialization
before the new domain is published, so that concurrent usage sites
won't see a half initialized interrupt domain. Similar problems
exist on teardown.
This has turned out to be a real problem due to the deferred and
parallel probing which was added in recent years.
Handling this at the core level allows to remove quite some accrued
boilerplate code in existing drivers and avoids horrible
workarounds at the driver level.
- The usual small improvements all over the place
Drivers:
- Add support for LAN966x OIC and RZ/Five SoC
- Split the STM ExtI driver into a microcontroller and a SMP version
to allow building the latter as a module for multi-platform
kernels
- Enable MSI support for Armada 370XP on platforms which do not
support IPIs
- The usual small fixes and enhancements all over the place"
* tag 'irq-core-2024-07-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
irqdomain: Fix the kernel-doc and plug it into Documentation
genirq: Set IRQF_COND_ONESHOT in request_irq()
irqchip/imx-irqsteer: Handle runtime power management correctly
irqchip/gic-v3: Pass #redistributor-regions to gic_of_setup_kvm_info()
irqchip/bcm2835: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
irqchip/gic-v4: Make sure a VPE is locked when VMAPP is issued
irqchip/gic-v4: Substitute vmovp_lock for a per-VM lock
irqchip/gic-v4: Always configure affinity on VPE activation
Revert "irqchip/dw-apb-ictl: Support building as module"
Revert "Loongarch: Support loongarch avec"
arm64: Kconfig: Allow build irq-stm32mp-exti driver as module
ARM: stm32: Allow build irq-stm32mp-exti driver as module
irqchip/stm32mp-exti: Allow building as module
irqchip/stm32mp-exti: Rename internal symbols
irqchip/stm32-exti: Split MCU and MPU code
arm64: Kconfig: Select STM32MP_EXTI on STM32 platforms
ARM: stm32: Use different EXTI driver on ARMv7m and ARMv7a
irqchip/stm32-exti: Add CONFIG_STM32MP_EXTI
irqchip/dw-apb-ictl: Support building as module
irqchip/riscv-aplic: Simplify the initialization code
...
Haibo Xu <haibo1.xu@intel.com> says:
This patch series enable RISC-V ACPI NUMA support which was based on
the recently approved ACPI ECR[1].
Patch 1/4 add RISC-V specific acpi_numa.c file to parse NUMA information
from SRAT and SLIT ACPI tables.
Patch 2/4 add the common SRAT RINTC affinity structure handler.
Patch 3/4 change the ACPI_NUMA to a hidden option since it would be selected
by default on all supported platform.
Patch 4/4 replace pr_info with pr_debug in arch_acpi_numa_init() to avoid
potential boot noise on ACPI platforms that are not NUMA.
Based-on: https://github.com/linux-riscv/linux-riscv/tree/for-next
[1] https://drive.google.com/file/d/1YTdDx2IPm5IeZjAW932EYU-tUtgS08tX/view?usp=sharing
Testing:
Since the ACPI AIA/PLIC support patch set is still under upstream review,
hence it is tested using the poll based HVC SBI console and RAM disk.
1) Build latest Qemu with the following patch backported
42bd4eeefd
2) Build latest EDK-II
https://github.com/tianocore/edk2/blob/master/OvmfPkg/RiscVVirt/README.md
3) Build Linux with the following configs enabled
CONFIG_RISCV_SBI_V01=y
CONFIG_SERIAL_EARLYCON_RISCV_SBI=y
CONFIG_NONPORTABLE=y
CONFIG_HVC_RISCV_SBI=y
CONFIG_NUMA=y
CONFIG_ACPI_NUMA=y
4) Build buildroot rootfs.cpio
5) Launch the Qemu machine
qemu-system-riscv64 -nographic \
-machine virt,pflash0=pflash0,pflash1=pflash1 -smp 4 -m 8G \
-blockdev node-name=pflash0,driver=file,read-only=on,filename=RISCV_VIRT_CODE.fd \
-blockdev node-name=pflash1,driver=file,filename=RISCV_VIRT_VARS.fd \
-object memory-backend-ram,size=4G,id=m0 \
-object memory-backend-ram,size=4G,id=m1 \
-numa node,memdev=m0,cpus=0-1,nodeid=0 \
-numa node,memdev=m1,cpus=2-3,nodeid=1 \
-numa dist,src=0,dst=1,val=30 \
-kernel linux/arch/riscv/boot/Image \
-initrd buildroot/output/images/rootfs.cpio \
-append "root=/dev/ram ro console=hvc0 earlycon=sbi"
[ 0.000000] ACPI: SRAT: Node 0 PXM 0 [mem 0x80000000-0x17fffffff]
[ 0.000000] ACPI: SRAT: Node 1 PXM 1 [mem 0x180000000-0x27fffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0x17fe3bc40-0x17fe3cfff]
[ 0.000000] NUMA: NODE_DATA [mem 0x27fff4c40-0x27fff5fff]
...
[ 0.000000] ACPI: NUMA: SRAT: PXM 0 -> HARTID 0x0 -> Node 0
[ 0.000000] ACPI: NUMA: SRAT: PXM 0 -> HARTID 0x1 -> Node 0
[ 0.000000] ACPI: NUMA: SRAT: PXM 1 -> HARTID 0x2 -> Node 1
[ 0.000000] ACPI: NUMA: SRAT: PXM 1 -> HARTID 0x3 -> Node 1
* b4-shazam-merge:
ACPI: NUMA: replace pr_info with pr_debug in arch_acpi_numa_init
ACPI: NUMA: change the ACPI_NUMA to a hidden option
ACPI: NUMA: Add handler for SRAT RINTC affinity structure
ACPI: RISCV: Add NUMA support based on SRAT and SLIT
Link: https://lore.kernel.org/r/cover.1718268003.git.haibo1.xu@intel.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
x86/arm64/loongarch would select ACPI_NUMA by default and riscv
would do the same thing, so change it to a hidden option and the
select statements except for the X86_64_ACPI_NUMA can also go away.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Sunil V L <sunilvl@ventanamicro.com>
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/f1f96377b8ecd6e3183f28abf5c9ac21cb9855ea.1718268003.git.haibo1.xu@intel.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
walkers") is known to cause a performance regression
(https://lore.kernel.org/all/3acefad9-96e5-4681-8014-827d6be71c7a@linux.ibm.com/T/#mfa809800a7862fb5bdf834c6f71a3a5113eb83ff).
Yu has a fix which I'll send along later via the hotfixes branch.
- In the series "mm: Avoid possible overflows in dirty throttling" Jan
Kara addresses a couple of issues in the writeback throttling code.
These fixes are also targetted at -stable kernels.
- Ryusuke Konishi's series "nilfs2: fix potential issues related to
reserved inodes" does that. This should actually be in the
mm-nonmm-stable tree, along with the many other nilfs2 patches. My bad.
- More folio conversions from Kefeng Wang in the series "mm: convert to
folio_alloc_mpol()"
- Kemeng Shi has sent some cleanups to the writeback code in the series
"Add helper functions to remove repeated code and improve readability of
cgroup writeback"
- Kairui Song has made the swap code a little smaller and a little
faster in the series "mm/swap: clean up and optimize swap cache index".
- In the series "mm/memory: cleanly support zeropage in
vm_insert_page*(), vm_map_pages*() and vmf_insert_mixed()" David
Hildenbrand has reworked the rather sketchy handling of the use of the
zeropage in MAP_SHARED mappings. I don't see any runtime effects here -
more a cleanup/understandability/maintainablity thing.
- Dev Jain has improved selftests/mm/va_high_addr_switch.c's handling of
higher addresses, for aarch64. The (poorly named) series is
"Restructure va_high_addr_switch".
- The core TLB handling code gets some cleanups and possible slight
optimizations in Bang Li's series "Add update_mmu_tlb_range() to
simplify code".
- Jane Chu has improved the handling of our
fake-an-unrecoverable-memory-error testing feature MADV_HWPOISON in the
series "Enhance soft hwpoison handling and injection".
- Jeff Johnson has sent a billion patches everywhere to add
MODULE_DESCRIPTION() to everything. Some landed in this pull.
- In the series "mm: cleanup MIGRATE_SYNC_NO_COPY mode", Kefeng Wang has
simplified migration's use of hardware-offload memory copying.
- Yosry Ahmed performs more folio API conversions in his series "mm:
zswap: trivial folio conversions".
- In the series "large folios swap-in: handle refault cases first",
Chuanhua Han inches us forward in the handling of large pages in the
swap code. This is a cleanup and optimization, working toward the end
objective of full support of large folio swapin/out.
- In the series "mm,swap: cleanup VMA based swap readahead window
calculation", Huang Ying has contributed some cleanups and a possible
fixlet to his VMA based swap readahead code.
- In the series "add mTHP support for anonymous shmem" Baolin Wang has
taught anonymous shmem mappings to use multisize THP. By default this
is a no-op - users must opt in vis sysfs controls. Dramatic
improvements in pagefault latency are realized.
- David Hildenbrand has some cleanups to our remaining use of
page_mapcount() in the series "fs/proc: move page_mapcount() to
fs/proc/internal.h".
- David also has some highmem accounting cleanups in the series
"mm/highmem: don't track highmem pages manually".
- Build-time fixes and cleanups from John Hubbard in the series
"cleanups, fixes, and progress towards avoiding "make headers"".
- Cleanups and consolidation of the core pagemap handling from Barry
Song in the series "mm: introduce pmd|pte_needs_soft_dirty_wp helpers
and utilize them".
- Lance Yang's series "Reclaim lazyfree THP without splitting" has
reduced the latency of the reclaim of pmd-mapped THPs under fairly
common circumstances. A 10x speedup is seen in a microbenchmark.
It does this by punting to aother CPU but I guess that's a win unless
all CPUs are pegged.
- hugetlb_cgroup cleanups from Xiu Jianfeng in the series
"mm/hugetlb_cgroup: rework on cftypes".
- Miaohe Lin's series "Some cleanups for memory-failure" does just that
thing.
- Is anyone reading this stuff? If so, email me!
- Someone other than SeongJae has developed a DAMON feature in Honggyu
Kim's series "DAMON based tiered memory management for CXL memory".
This adds DAMON features which may be used to help determine the
efficiency of our placement of CXL/PCIe attached DRAM.
- DAMON user API centralization and simplificatio work in SeongJae
Park's series "mm/damon: introduce DAMON parameters online commit
function".
- In the series "mm: page_type, zsmalloc and page_mapcount_reset()"
David Hildenbrand does some maintenance work on zsmalloc - partially
modernizing its use of pageframe fields.
- Kefeng Wang provides more folio conversions in the series "mm: remove
page_maybe_dma_pinned() and page_mkclean()".
- More cleanup from David Hildenbrand, this time in the series
"mm/memory_hotplug: use PageOffline() instead of PageReserved() for
!ZONE_DEVICE". It "enlightens memory hotplug more about PageOffline()
pages" and permits the removal of some virtio-mem hacks.
- Barry Song's series "mm: clarify folio_add_new_anon_rmap() and
__folio_add_anon_rmap()" is a cleanup to the anon folio handling in
preparation for mTHP (multisize THP) swapin.
- Kefeng Wang's series "mm: improve clear and copy user folio"
implements more folio conversions, this time in the area of large folio
userspace copying.
- The series "Docs/mm/damon/maintaier-profile: document a mailing tool
and community meetup series" tells people how to get better involved
with other DAMON developers. From SeongJae Park.
- A large series ("kmsan: Enable on s390") from Ilya Leoshkevich does
that.
- David Hildenbrand sends along more cleanups, this time against the
migration code. The series is "mm/migrate: move NUMA hinting fault
folio isolation + checks under PTL".
- Jan Kara has found quite a lot of strangenesses and minor errors in
the readahead code. He addresses this in the series "mm: Fix various
readahead quirks".
- SeongJae Park's series "selftests/damon: test DAMOS tried regions and
{min,max}_nr_regions" adds features and addresses errors in DAMON's self
testing code.
- Gavin Shan has found a userspace-triggerable WARN in the pagecache
code. The series "mm/filemap: Limit page cache size to that supported
by xarray" addresses this. The series is marked cc:stable.
- Chengming Zhou's series "mm/ksm: cmp_and_merge_page() optimizations
and cleanup" cleans up and slightly optimizes KSM.
- Roman Gushchin has separated the memcg-v1 and memcg-v2 code - lots of
code motion. The series (which also makes the memcg-v1 code
Kconfigurable) are
"mm: memcg: separate legacy cgroup v1 code and put under config
option" and
"mm: memcg: put cgroup v1-specific memcg data under CONFIG_MEMCG_V1"
- Dan Schatzberg's series "Add swappiness argument to memory.reclaim"
adds an additional feature to this cgroup-v2 control file.
- The series "Userspace controls soft-offline pages" from Jiaqi Yan
permits userspace to stop the kernel's automatic treatment of excessive
correctable memory errors. In order to permit userspace to monitor and
handle this situation.
- Kefeng Wang's series "mm: migrate: support poison recover from migrate
folio" teaches the kernel to appropriately handle migration from
poisoned source folios rather than simply panicing.
- SeongJae Park's series "Docs/damon: minor fixups and improvements"
does those things.
- In the series "mm/zsmalloc: change back to per-size_class lock"
Chengming Zhou improves zsmalloc's scalability and memory utilization.
- Vivek Kasireddy's series "mm/gup: Introduce memfd_pin_folios() for
pinning memfd folios" makes the GUP code use FOLL_PIN rather than bare
refcount increments. So these paes can first be moved aside if they
reside in the movable zone or a CMA block.
- Andrii Nakryiko has added a binary ioctl()-based API to /proc/pid/maps
for much faster reading of vma information. The series is "query VMAs
from /proc/<pid>/maps".
- In the series "mm: introduce per-order mTHP split counters" Lance Yang
improves the kernel's presentation of developer information related to
multisize THP splitting.
- Michael Ellerman has developed the series "Reimplement huge pages
without hugepd on powerpc (8xx, e500, book3s/64)". This permits
userspace to use all available huge page sizes.
- In the series "revert unconditional slab and page allocator fault
injection calls" Vlastimil Babka removes a performance-affecting and not
very useful feature from slab fault injection.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZp2C+QAKCRDdBJ7gKXxA
joTkAQDvjqOoFStqk4GU3OXMYB7WCU/ZQMFG0iuu1EEwTVDZ4QEA8CnG7seek1R3
xEoo+vw0sWWeLV3qzsxnCA1BJ8cTJA8=
=z0Lf
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2024-07-21-14-50' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- In the series "mm: Avoid possible overflows in dirty throttling" Jan
Kara addresses a couple of issues in the writeback throttling code.
These fixes are also targetted at -stable kernels.
- Ryusuke Konishi's series "nilfs2: fix potential issues related to
reserved inodes" does that. This should actually be in the
mm-nonmm-stable tree, along with the many other nilfs2 patches. My
bad.
- More folio conversions from Kefeng Wang in the series "mm: convert to
folio_alloc_mpol()"
- Kemeng Shi has sent some cleanups to the writeback code in the series
"Add helper functions to remove repeated code and improve readability
of cgroup writeback"
- Kairui Song has made the swap code a little smaller and a little
faster in the series "mm/swap: clean up and optimize swap cache
index".
- In the series "mm/memory: cleanly support zeropage in
vm_insert_page*(), vm_map_pages*() and vmf_insert_mixed()" David
Hildenbrand has reworked the rather sketchy handling of the use of
the zeropage in MAP_SHARED mappings. I don't see any runtime effects
here - more a cleanup/understandability/maintainablity thing.
- Dev Jain has improved selftests/mm/va_high_addr_switch.c's handling
of higher addresses, for aarch64. The (poorly named) series is
"Restructure va_high_addr_switch".
- The core TLB handling code gets some cleanups and possible slight
optimizations in Bang Li's series "Add update_mmu_tlb_range() to
simplify code".
- Jane Chu has improved the handling of our
fake-an-unrecoverable-memory-error testing feature MADV_HWPOISON in
the series "Enhance soft hwpoison handling and injection".
- Jeff Johnson has sent a billion patches everywhere to add
MODULE_DESCRIPTION() to everything. Some landed in this pull.
- In the series "mm: cleanup MIGRATE_SYNC_NO_COPY mode", Kefeng Wang
has simplified migration's use of hardware-offload memory copying.
- Yosry Ahmed performs more folio API conversions in his series "mm:
zswap: trivial folio conversions".
- In the series "large folios swap-in: handle refault cases first",
Chuanhua Han inches us forward in the handling of large pages in the
swap code. This is a cleanup and optimization, working toward the end
objective of full support of large folio swapin/out.
- In the series "mm,swap: cleanup VMA based swap readahead window
calculation", Huang Ying has contributed some cleanups and a possible
fixlet to his VMA based swap readahead code.
- In the series "add mTHP support for anonymous shmem" Baolin Wang has
taught anonymous shmem mappings to use multisize THP. By default this
is a no-op - users must opt in vis sysfs controls. Dramatic
improvements in pagefault latency are realized.
- David Hildenbrand has some cleanups to our remaining use of
page_mapcount() in the series "fs/proc: move page_mapcount() to
fs/proc/internal.h".
- David also has some highmem accounting cleanups in the series
"mm/highmem: don't track highmem pages manually".
- Build-time fixes and cleanups from John Hubbard in the series
"cleanups, fixes, and progress towards avoiding "make headers"".
- Cleanups and consolidation of the core pagemap handling from Barry
Song in the series "mm: introduce pmd|pte_needs_soft_dirty_wp helpers
and utilize them".
- Lance Yang's series "Reclaim lazyfree THP without splitting" has
reduced the latency of the reclaim of pmd-mapped THPs under fairly
common circumstances. A 10x speedup is seen in a microbenchmark.
It does this by punting to aother CPU but I guess that's a win unless
all CPUs are pegged.
- hugetlb_cgroup cleanups from Xiu Jianfeng in the series
"mm/hugetlb_cgroup: rework on cftypes".
- Miaohe Lin's series "Some cleanups for memory-failure" does just that
thing.
- Someone other than SeongJae has developed a DAMON feature in Honggyu
Kim's series "DAMON based tiered memory management for CXL memory".
This adds DAMON features which may be used to help determine the
efficiency of our placement of CXL/PCIe attached DRAM.
- DAMON user API centralization and simplificatio work in SeongJae
Park's series "mm/damon: introduce DAMON parameters online commit
function".
- In the series "mm: page_type, zsmalloc and page_mapcount_reset()"
David Hildenbrand does some maintenance work on zsmalloc - partially
modernizing its use of pageframe fields.
- Kefeng Wang provides more folio conversions in the series "mm: remove
page_maybe_dma_pinned() and page_mkclean()".
- More cleanup from David Hildenbrand, this time in the series
"mm/memory_hotplug: use PageOffline() instead of PageReserved() for
!ZONE_DEVICE". It "enlightens memory hotplug more about PageOffline()
pages" and permits the removal of some virtio-mem hacks.
- Barry Song's series "mm: clarify folio_add_new_anon_rmap() and
__folio_add_anon_rmap()" is a cleanup to the anon folio handling in
preparation for mTHP (multisize THP) swapin.
- Kefeng Wang's series "mm: improve clear and copy user folio"
implements more folio conversions, this time in the area of large
folio userspace copying.
- The series "Docs/mm/damon/maintaier-profile: document a mailing tool
and community meetup series" tells people how to get better involved
with other DAMON developers. From SeongJae Park.
- A large series ("kmsan: Enable on s390") from Ilya Leoshkevich does
that.
- David Hildenbrand sends along more cleanups, this time against the
migration code. The series is "mm/migrate: move NUMA hinting fault
folio isolation + checks under PTL".
- Jan Kara has found quite a lot of strangenesses and minor errors in
the readahead code. He addresses this in the series "mm: Fix various
readahead quirks".
- SeongJae Park's series "selftests/damon: test DAMOS tried regions and
{min,max}_nr_regions" adds features and addresses errors in DAMON's
self testing code.
- Gavin Shan has found a userspace-triggerable WARN in the pagecache
code. The series "mm/filemap: Limit page cache size to that supported
by xarray" addresses this. The series is marked cc:stable.
- Chengming Zhou's series "mm/ksm: cmp_and_merge_page() optimizations
and cleanup" cleans up and slightly optimizes KSM.
- Roman Gushchin has separated the memcg-v1 and memcg-v2 code - lots of
code motion. The series (which also makes the memcg-v1 code
Kconfigurable) are "mm: memcg: separate legacy cgroup v1 code and put
under config option" and "mm: memcg: put cgroup v1-specific memcg
data under CONFIG_MEMCG_V1"
- Dan Schatzberg's series "Add swappiness argument to memory.reclaim"
adds an additional feature to this cgroup-v2 control file.
- The series "Userspace controls soft-offline pages" from Jiaqi Yan
permits userspace to stop the kernel's automatic treatment of
excessive correctable memory errors. In order to permit userspace to
monitor and handle this situation.
- Kefeng Wang's series "mm: migrate: support poison recover from
migrate folio" teaches the kernel to appropriately handle migration
from poisoned source folios rather than simply panicing.
- SeongJae Park's series "Docs/damon: minor fixups and improvements"
does those things.
- In the series "mm/zsmalloc: change back to per-size_class lock"
Chengming Zhou improves zsmalloc's scalability and memory
utilization.
- Vivek Kasireddy's series "mm/gup: Introduce memfd_pin_folios() for
pinning memfd folios" makes the GUP code use FOLL_PIN rather than
bare refcount increments. So these paes can first be moved aside if
they reside in the movable zone or a CMA block.
- Andrii Nakryiko has added a binary ioctl()-based API to
/proc/pid/maps for much faster reading of vma information. The series
is "query VMAs from /proc/<pid>/maps".
- In the series "mm: introduce per-order mTHP split counters" Lance
Yang improves the kernel's presentation of developer information
related to multisize THP splitting.
- Michael Ellerman has developed the series "Reimplement huge pages
without hugepd on powerpc (8xx, e500, book3s/64)". This permits
userspace to use all available huge page sizes.
- In the series "revert unconditional slab and page allocator fault
injection calls" Vlastimil Babka removes a performance-affecting and
not very useful feature from slab fault injection.
* tag 'mm-stable-2024-07-21-14-50' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (411 commits)
mm/mglru: fix ineffective protection calculation
mm/zswap: fix a white space issue
mm/hugetlb: fix kernel NULL pointer dereference when migrating hugetlb folio
mm/hugetlb: fix possible recursive locking detected warning
mm/gup: clear the LRU flag of a page before adding to LRU batch
mm/numa_balancing: teach mpol_to_str about the balancing mode
mm: memcg1: convert charge move flags to unsigned long long
alloc_tag: fix page_ext_get/page_ext_put sequence during page splitting
lib: reuse page_ext_data() to obtain codetag_ref
lib: add missing newline character in the warning message
mm/mglru: fix overshooting shrinker memory
mm/mglru: fix div-by-zero in vmpressure_calc_level()
mm/kmemleak: replace strncpy() with strscpy()
mm, page_alloc: put should_fail_alloc_page() back behing CONFIG_FAIL_PAGE_ALLOC
mm, slab: put should_failslab() back behind CONFIG_SHOULD_FAILSLAB
mm: ignore data-race in __swap_writepage
hugetlbfs: ensure generic_hugetlb_get_unmapped_area() returns higher address than mmap_min_addr
mm: shmem: rename mTHP shmem counters
mm: swap_state: use folio_alloc_mpol() in __read_swap_cache_async()
mm/migrate: putback split folios when numa hint migration fails
...
* Initial infrastructure for shadow stage-2 MMUs, as part of nested
virtualization enablement
* Support for userspace changes to the guest CTR_EL0 value, enabling
(in part) migration of VMs between heterogenous hardware
* Fixes + improvements to pKVM's FF-A proxy, adding support for v1.1 of
the protocol
* FPSIMD/SVE support for nested, including merged trap configuration
and exception routing
* New command-line parameter to control the WFx trap behavior under KVM
* Introduce kCFI hardening in the EL2 hypervisor
* Fixes + cleanups for handling presence/absence of FEAT_TCRX
* Miscellaneous fixes + documentation updates
LoongArch:
* Add paravirt steal time support.
* Add support for KVM_DIRTY_LOG_INITIALLY_SET.
* Add perf kvm-stat support for loongarch.
RISC-V:
* Redirect AMO load/store access fault traps to guest
* perf kvm stat support
* Use guest files for IMSIC virtualization, when available
ONE_REG support for the Zimop, Zcmop, Zca, Zcf, Zcd, Zcb and Zawrs ISA
extensions is coming through the RISC-V tree.
s390:
* Assortment of tiny fixes which are not time critical
x86:
* Fixes for Xen emulation.
* Add a global struct to consolidate tracking of host values, e.g. EFER
* Add KVM_CAP_X86_APIC_BUS_CYCLES_NS to allow configuring the effective APIC
bus frequency, because TDX.
* Print the name of the APICv/AVIC inhibits in the relevant tracepoint.
* Clean up KVM's handling of vendor specific emulation to consistently act on
"compatible with Intel/AMD", versus checking for a specific vendor.
* Drop MTRR virtualization, and instead always honor guest PAT on CPUs
that support self-snoop.
* Update to the newfangled Intel CPU FMS infrastructure.
* Don't advertise IA32_PERF_GLOBAL_OVF_CTRL as an MSR-to-be-saved, as it reads
'0' and writes from userspace are ignored.
* Misc cleanups
x86 - MMU:
* Small cleanups, renames and refactoring extracted from the upcoming
Intel TDX support.
* Don't allocate kvm_mmu_page.shadowed_translation for shadow pages that can't
hold leafs SPTEs.
* Unconditionally drop mmu_lock when allocating TDP MMU page tables for eager
page splitting, to avoid stalling vCPUs when splitting huge pages.
* Bug the VM instead of simply warning if KVM tries to split a SPTE that is
non-present or not-huge. KVM is guaranteed to end up in a broken state
because the callers fully expect a valid SPTE, it's all but dangerous
to let more MMU changes happen afterwards.
x86 - AMD:
* Make per-CPU save_area allocations NUMA-aware.
* Force sev_es_host_save_area() to be inlined to avoid calling into an
instrumentable function from noinstr code.
* Base support for running SEV-SNP guests. API-wise, this includes
a new KVM_X86_SNP_VM type, encrypting/measure the initial image into
guest memory, and finalizing it before launching it. Internally,
there are some gmem/mmu hooks needed to prepare gmem-allocated pages
before mapping them into guest private memory ranges.
This includes basic support for attestation guest requests, enough to
say that KVM supports the GHCB 2.0 specification.
There is no support yet for loading into the firmware those signing
keys to be used for attestation requests, and therefore no need yet
for the host to provide certificate data for those keys. To support
fetching certificate data from userspace, a new KVM exit type will be
needed to handle fetching the certificate from userspace. An attempt to
define a new KVM_EXIT_COCO/KVM_EXIT_COCO_REQ_CERTS exit type to handle
this was introduced in v1 of this patchset, but is still being discussed
by community, so for now this patchset only implements a stub version
of SNP Extended Guest Requests that does not provide certificate data.
x86 - Intel:
* Remove an unnecessary EPT TLB flush when enabling hardware.
* Fix a series of bugs that cause KVM to fail to detect nested pending posted
interrupts as valid wake eents for a vCPU executing HLT in L2 (with
HLT-exiting disable by L1).
* KVM: x86: Suppress MMIO that is triggered during task switch emulation
Explicitly suppress userspace emulated MMIO exits that are triggered when
emulating a task switch as KVM doesn't support userspace MMIO during
complex (multi-step) emulation. Silently ignoring the exit request can
result in the WARN_ON_ONCE(vcpu->mmio_needed) firing if KVM exits to
userspace for some other reason prior to purging mmio_needed.
See commit 0dc902267c ("KVM: x86: Suppress pending MMIO write exits if
emulator detects exception") for more details on KVM's limitations with
respect to emulated MMIO during complex emulator flows.
Generic:
* Rename the AS_UNMOVABLE flag that was introduced for KVM to AS_INACCESSIBLE,
because the special casing needed by these pages is not due to just
unmovability (and in fact they are only unmovable because the CPU cannot
access them).
* New ioctl to populate the KVM page tables in advance, which is useful to
mitigate KVM page faults during guest boot or after live migration.
The code will also be used by TDX, but (probably) not through the ioctl.
* Enable halt poll shrinking by default, as Intel found it to be a clear win.
* Setup empty IRQ routing when creating a VM to avoid having to synchronize
SRCU when creating a split IRQCHIP on x86.
* Rework the sched_in/out() paths to replace kvm_arch_sched_in() with a flag
that arch code can use for hooking both sched_in() and sched_out().
* Take the vCPU @id as an "unsigned long" instead of "u32" to avoid
truncating a bogus value from userspace, e.g. to help userspace detect bugs.
* Mark a vCPU as preempted if and only if it's scheduled out while in the
KVM_RUN loop, e.g. to avoid marking it preempted and thus writing guest
memory when retrieving guest state during live migration blackout.
Selftests:
* Remove dead code in the memslot modification stress test.
* Treat "branch instructions retired" as supported on all AMD Family 17h+ CPUs.
* Print the guest pseudo-RNG seed only when it changes, to avoid spamming the
log for tests that create lots of VMs.
* Make the PMU counters test less flaky when counting LLC cache misses by
doing CLFLUSH{OPT} in every loop iteration.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmaZQB0UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNkZwf/bv2jiENaLFNGPe/VqTKMQ6PHQLMG
+sNHx6fJPP35gTM8Jqf0/7/ummZXcSuC1mWrzYbecZm7Oeg3vwNXHZ4LquwwX6Dv
8dKcUzLbWDAC4WA3SKhi8C8RV2v6E7ohy69NtAJmFWTc7H95dtIQm6cduV2osTC3
OEuHe1i8d9umk6couL9Qhm8hk3i9v2KgCsrfyNrQgLtS3hu7q6yOTR8nT0iH6sJR
KE5A8prBQgLmF34CuvYDw4Hu6E4j+0QmIqodovg2884W1gZQ9LmcVqYPaRZGsG8S
iDdbkualLKwiR1TpRr3HJGKWSFdc7RblbsnHRvHIZgFsMQiimh4HrBSCyQ==
=zepX
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- Initial infrastructure for shadow stage-2 MMUs, as part of nested
virtualization enablement
- Support for userspace changes to the guest CTR_EL0 value, enabling
(in part) migration of VMs between heterogenous hardware
- Fixes + improvements to pKVM's FF-A proxy, adding support for v1.1
of the protocol
- FPSIMD/SVE support for nested, including merged trap configuration
and exception routing
- New command-line parameter to control the WFx trap behavior under
KVM
- Introduce kCFI hardening in the EL2 hypervisor
- Fixes + cleanups for handling presence/absence of FEAT_TCRX
- Miscellaneous fixes + documentation updates
LoongArch:
- Add paravirt steal time support
- Add support for KVM_DIRTY_LOG_INITIALLY_SET
- Add perf kvm-stat support for loongarch
RISC-V:
- Redirect AMO load/store access fault traps to guest
- perf kvm stat support
- Use guest files for IMSIC virtualization, when available
s390:
- Assortment of tiny fixes which are not time critical
x86:
- Fixes for Xen emulation
- Add a global struct to consolidate tracking of host values, e.g.
EFER
- Add KVM_CAP_X86_APIC_BUS_CYCLES_NS to allow configuring the
effective APIC bus frequency, because TDX
- Print the name of the APICv/AVIC inhibits in the relevant
tracepoint
- Clean up KVM's handling of vendor specific emulation to
consistently act on "compatible with Intel/AMD", versus checking
for a specific vendor
- Drop MTRR virtualization, and instead always honor guest PAT on
CPUs that support self-snoop
- Update to the newfangled Intel CPU FMS infrastructure
- Don't advertise IA32_PERF_GLOBAL_OVF_CTRL as an MSR-to-be-saved, as
it reads '0' and writes from userspace are ignored
- Misc cleanups
x86 - MMU:
- Small cleanups, renames and refactoring extracted from the upcoming
Intel TDX support
- Don't allocate kvm_mmu_page.shadowed_translation for shadow pages
that can't hold leafs SPTEs
- Unconditionally drop mmu_lock when allocating TDP MMU page tables
for eager page splitting, to avoid stalling vCPUs when splitting
huge pages
- Bug the VM instead of simply warning if KVM tries to split a SPTE
that is non-present or not-huge. KVM is guaranteed to end up in a
broken state because the callers fully expect a valid SPTE, it's
all but dangerous to let more MMU changes happen afterwards
x86 - AMD:
- Make per-CPU save_area allocations NUMA-aware
- Force sev_es_host_save_area() to be inlined to avoid calling into
an instrumentable function from noinstr code
- Base support for running SEV-SNP guests. API-wise, this includes a
new KVM_X86_SNP_VM type, encrypting/measure the initial image into
guest memory, and finalizing it before launching it. Internally,
there are some gmem/mmu hooks needed to prepare gmem-allocated
pages before mapping them into guest private memory ranges
This includes basic support for attestation guest requests, enough
to say that KVM supports the GHCB 2.0 specification
There is no support yet for loading into the firmware those signing
keys to be used for attestation requests, and therefore no need yet
for the host to provide certificate data for those keys.
To support fetching certificate data from userspace, a new KVM exit
type will be needed to handle fetching the certificate from
userspace.
An attempt to define a new KVM_EXIT_COCO / KVM_EXIT_COCO_REQ_CERTS
exit type to handle this was introduced in v1 of this patchset, but
is still being discussed by community, so for now this patchset
only implements a stub version of SNP Extended Guest Requests that
does not provide certificate data
x86 - Intel:
- Remove an unnecessary EPT TLB flush when enabling hardware
- Fix a series of bugs that cause KVM to fail to detect nested
pending posted interrupts as valid wake eents for a vCPU executing
HLT in L2 (with HLT-exiting disable by L1)
- KVM: x86: Suppress MMIO that is triggered during task switch
emulation
Explicitly suppress userspace emulated MMIO exits that are
triggered when emulating a task switch as KVM doesn't support
userspace MMIO during complex (multi-step) emulation
Silently ignoring the exit request can result in the
WARN_ON_ONCE(vcpu->mmio_needed) firing if KVM exits to userspace
for some other reason prior to purging mmio_needed
See commit 0dc902267c ("KVM: x86: Suppress pending MMIO write
exits if emulator detects exception") for more details on KVM's
limitations with respect to emulated MMIO during complex emulator
flows
Generic:
- Rename the AS_UNMOVABLE flag that was introduced for KVM to
AS_INACCESSIBLE, because the special casing needed by these pages
is not due to just unmovability (and in fact they are only
unmovable because the CPU cannot access them)
- New ioctl to populate the KVM page tables in advance, which is
useful to mitigate KVM page faults during guest boot or after live
migration. The code will also be used by TDX, but (probably) not
through the ioctl
- Enable halt poll shrinking by default, as Intel found it to be a
clear win
- Setup empty IRQ routing when creating a VM to avoid having to
synchronize SRCU when creating a split IRQCHIP on x86
- Rework the sched_in/out() paths to replace kvm_arch_sched_in() with
a flag that arch code can use for hooking both sched_in() and
sched_out()
- Take the vCPU @id as an "unsigned long" instead of "u32" to avoid
truncating a bogus value from userspace, e.g. to help userspace
detect bugs
- Mark a vCPU as preempted if and only if it's scheduled out while in
the KVM_RUN loop, e.g. to avoid marking it preempted and thus
writing guest memory when retrieving guest state during live
migration blackout
Selftests:
- Remove dead code in the memslot modification stress test
- Treat "branch instructions retired" as supported on all AMD Family
17h+ CPUs
- Print the guest pseudo-RNG seed only when it changes, to avoid
spamming the log for tests that create lots of VMs
- Make the PMU counters test less flaky when counting LLC cache
misses by doing CLFLUSH{OPT} in every loop iteration"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
crypto: ccp: Add the SNP_VLEK_LOAD command
KVM: x86/pmu: Add kvm_pmu_call() to simplify static calls of kvm_pmu_ops
KVM: x86: Introduce kvm_x86_call() to simplify static calls of kvm_x86_ops
KVM: x86: Replace static_call_cond() with static_call()
KVM: SEV: Provide support for SNP_EXTENDED_GUEST_REQUEST NAE event
x86/sev: Move sev_guest.h into common SEV header
KVM: SEV: Provide support for SNP_GUEST_REQUEST NAE event
KVM: x86: Suppress MMIO that is triggered during task switch emulation
KVM: x86/mmu: Clean up make_huge_page_split_spte() definition and intro
KVM: x86/mmu: Bug the VM if KVM tries to split a !hugepage SPTE
KVM: selftests: x86: Add test for KVM_PRE_FAULT_MEMORY
KVM: x86: Implement kvm_arch_vcpu_pre_fault_memory()
KVM: x86/mmu: Make kvm_mmu_do_page_fault() return mapped level
KVM: x86/mmu: Account pf_{fixed,emulate,spurious} in callers of "do page fault"
KVM: x86/mmu: Bump pf_taken stat only in the "real" page fault handler
KVM: Add KVM_PRE_FAULT_MEMORY vcpu ioctl to pre-populate guest memory
KVM: Document KVM_PRE_FAULT_MEMORY ioctl
mm, virt: merge AS_UNMOVABLE and AS_INACCESSIBLE
perf kvm: Add kvm-stat for loongarch64
LoongArch: KVM: Add PV steal time support in guest side
...
Setting '-e' flag tells shells to exit with error exit code immediately
after any of commands fails, and causes make(1) to regard recipes as
failed.
Before this, make will still continue to succeed even after the
installation failed, for example, for insufficient permission or
directory does not exist.
Signed-off-by: Zhang Bingwu <xtexchooser@duck.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities for
thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppaNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXZwCgrEtIAQw0x6EF7w/iTWVS5UJj9AEAoLCj5UwO
WX978uThyUctuYYKbw+8
=Cm7j
-----END PGP SIGNATURE-----
Merge tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities
for thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (112 commits)
kselftest: devices: Add test to detect device error logs
kselftest: Move ksft helper module to common directory
kselftest: devices: Move discoverable devices test to subdirectory
usb: gadget: f_uac2: fix non-newline-terminated function name
USB: uas: Implement the new shutdown callback
USB: core: add 'shutdown' callback to usb_driver
usb: typec: Drop explicit initialization of struct i2c_device_id::driver_data to 0
usb: dwc3: enable CCI support for AMD-xilinx DWC3 controller
usb: dwc2: add support for other Lantiq SoCs
usb: gadget: Use u16 types for 16-bit fields
usb: gadget: midi2: Fix incorrect default MIDI2 protocol setup
usb: dwc3: core: Check all ports when set phy suspend
usb: typec: tcpci: add support to set connector orientation
dt-bindings: usb: Convert fsl-usb to yaml
usb: typec: ucsi: reorder operations in ucsi_run_command()
usb: typec: ucsi: extract common code for command handling
usb: typec: ucsi: inline ucsi_read_message_in
usb: typec: ucsi: rework command execution functions
usb: typec: ucsi: split read operation
usb: typec: ucsi: simplify command sending API
...
- fix an invalid pointer dereference in error path in pwrseq core
- reduce the Kconfig noise from PCI pwrctl choices
-----BEGIN PGP SIGNATURE-----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=I1ot
-----END PGP SIGNATURE-----
Merge tag 'pwrseq-fixes-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing fixes from Bartosz Golaszewski:
"There's one fix for an invalid pointer dereference in error path
reported by smatch and two patches that address the noisy config
choices you reported earlier this week.
Summary:
- fix an invalid pointer dereference in error path in pwrseq core
- reduce the Kconfig noise from PCI pwrctl choices"
* tag 'pwrseq-fixes-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
arm64: qcom: don't select HAVE_PWRCTL when PCI=n
Kconfig: reduce the amount of power sequencing noise
power: sequencing: fix an invalid pointer dereference in error path
Lots of changes in this cycle, but mostly for cleanups and
refactoring. Significant amount of changes are about DT schema
conversions for ASoC at this time while we see other usual
suspects, too. Some highlights below:
Core:
- Re-introduction of PCM sync ID support API
- MIDI2 time-base extension in ALSA sequencer API
ASoC:
- Syncing of features between simple-audio-card and the two
audio-graph cards
- Support for specifying the order of operations for components
within cards to allow quirking for unusual systems
- Lots of DT schema conversions
- Continued SOF/Intel updates for topology, SoundWire, IPC3/4
- New support for Asahi Kasei AK4619, Cirrus Logic CS530x, Everest
Semiconductors ES8311, NXP i.MX95 and LPC32xx, Qualcomm LPASS
v2.5 and WCD937x, Realtek RT1318 and RT1320 and Texas
Instruments PCM5242
HD-audio:
- More quirks, Intel PantherLake support, senarytech codec support
- Refactoring of Cirrus codec component-binding
Others:
- ALSA control kselftest improvements, and fixes for input value
checks in various drivers
-----BEGIN PGP SIGNATURE-----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=hn0h
-----END PGP SIGNATURE-----
Merge tag 'sound-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Lots of changes in this cycle, but mostly for cleanups and
refactoring.
Significant amount of changes are about DT schema conversions for ASoC
at this time while we see other usual suspects, too.
Some highlights below:
Core:
- Re-introduction of PCM sync ID support API
- MIDI2 time-base extension in ALSA sequencer API
ASoC:
- Syncing of features between simple-audio-card and the two
audio-graph cards
- Support for specifying the order of operations for components
within cards to allow quirking for unusual systems
- Lots of DT schema conversions
- Continued SOF/Intel updates for topology, SoundWire, IPC3/4
- New support for Asahi Kasei AK4619, Cirrus Logic CS530x, Everest
Semiconductors ES8311, NXP i.MX95 and LPC32xx, Qualcomm LPASS v2.5
and WCD937x, Realtek RT1318 and RT1320 and Texas Instruments
PCM5242
HD-audio:
- More quirks, Intel PantherLake support, senarytech codec support
- Refactoring of Cirrus codec component-binding
Others:
- ALSA control kselftest improvements, and fixes for input value
checks in various drivers"
* tag 'sound-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (349 commits)
kselftest/alsa: Log the PCM ID in pcm-test
kselftest/alsa: Use card name rather than number in test names
ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
ALSA: hda/tas2781: Add new quirk for Lenovo Hera2 Laptop
ALSA: seq: ump: Skip useless ports for static blocks
ALSA: pcm_dmaengine: Don't synchronize DMA channel when DMA is paused
ALSA: usb: Use BIT() for bit values
ALSA: usb: Fix UBSAN warning in parse_audio_unit()
ALSA: hda/realtek: Enable headset mic on Positivo SU C1400
ASoC: tas2781: Add new Kontrol to set tas2563 digital Volume
ASoC: codecs: wcd937x: Remove separate handling for vdd-buck supply
ASoC: codecs: wcd937x: Remove the string compare in MIC BIAS widget settings
ASoC: codecs: wcd937x-sdw: Fix Unbalanced pm_runtime_enable
ASoC: dt-bindings: cirrus,cs42xx8: Convert to dtschema
ASoC: cs530x: Remove bclk from private structure
ASoC: cs530x: Calculate proper bclk rate using TDM
ASoC: dt-bindings: cirrus,cs4270: Convert to dtschema
firmware: cs_dsp: Rename fw_ver to wmfw_ver
firmware: cs_dsp: Clarify wmfw format version log message
firmware: cs_dsp: Make wmfw and bin filename arguments const char *
...
- Core:
* Support for the "ats-supported" device-tree property.
* Removal of the 'ops' field from 'struct iommu_fwspec'.
* Introduction of iommu_paging_domain_alloc() and partial conversion
of existing users.
* Introduce 'struct iommu_attach_handle' and provide corresponding
IOMMU interfaces which will be used by the IOMMUFD subsystem.
* Remove stale documentation.
* Add missing MODULE_DESCRIPTION() macro.
* Misc cleanups.
- Allwinner Sun50i:
* Ensure bypass mode is disabled on H616 SoCs.
* Ensure page-tables are allocated below 4GiB for the 32-bit
page-table walker.
* Add new device-tree compatible strings.
- AMD Vi:
* Use try_cmpxchg64() instead of cmpxchg64() when updating pte.
- Arm SMMUv2:
* Print much more useful information on context faults.
* Fix Qualcomm TBU probing when CONFIG_ARM_SMMU_QCOM_DEBUG=n.
* Add new Qualcomm device-tree bindings.
- Arm SMMUv3:
* Support for hardware update of access/dirty bits and reporting via
IOMMUFD.
* More driver rework from Jason, this time updating the PASID/SVA support
to prepare for full IOMMUFD support.
* Add missing MODULE_DESCRIPTION() macro.
* Minor fixes and cleanups.
- NVIDIA Tegra:
* Fix for benign fwspec initialisation issue exposed by rework on the
core branch.
- Intel VT-d:
* Use try_cmpxchg64() instead of cmpxchg64() when updating pte.
* Use READ_ONCE() to read volatile descriptor status.
* Remove support for handling Execute-Requested requests.
* Avoid calling iommu_domain_alloc().
* Minor fixes and refactoring.
- Qualcomm MSM:
* Updates to the device-tree bindings.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmaZTqMQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNApdB/wL2gW7ANJN3KDrOiWdq06P9fuzxbuiAegI
aKGH+aT05kJjLBXpAE5K9Bas0RbgN8iIB4TITDR9jyLnMOlTP3poy0fvB8y27q00
/WkQ7yVPkZc58ySdEOGH/EbuQkiXcD1YTjTGWP9071xzbWTDbsYN0smfbvvB9LgI
56KhdcUtB0QsqhqBzyyznHJLFdpVvDpbkiAFDXJfor7SNOOtV9a4Ect6IYteaYKz
S6+DWDEfUs+fHTEKEZ9sZVA745f2zPkT/YHY8vjLOEukWN07+3/2AKTra19DIgqF
HCGitRyZjOut1fg8sLn0SUliCKe/G/bHlwSbHnxJQ73b91YDvpzD
=xvLD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Will Deacon:
"Core:
- Support for the "ats-supported" device-tree property
- Removal of the 'ops' field from 'struct iommu_fwspec'
- Introduction of iommu_paging_domain_alloc() and partial conversion
of existing users
- Introduce 'struct iommu_attach_handle' and provide corresponding
IOMMU interfaces which will be used by the IOMMUFD subsystem
- Remove stale documentation
- Add missing MODULE_DESCRIPTION() macro
- Misc cleanups
Allwinner Sun50i:
- Ensure bypass mode is disabled on H616 SoCs
- Ensure page-tables are allocated below 4GiB for the 32-bit
page-table walker
- Add new device-tree compatible strings
AMD Vi:
- Use try_cmpxchg64() instead of cmpxchg64() when updating pte
Arm SMMUv2:
- Print much more useful information on context faults
- Fix Qualcomm TBU probing when CONFIG_ARM_SMMU_QCOM_DEBUG=n
- Add new Qualcomm device-tree bindings
Arm SMMUv3:
- Support for hardware update of access/dirty bits and reporting via
IOMMUFD
- More driver rework from Jason, this time updating the PASID/SVA
support to prepare for full IOMMUFD support
- Add missing MODULE_DESCRIPTION() macro
- Minor fixes and cleanups
NVIDIA Tegra:
- Fix for benign fwspec initialisation issue exposed by rework on the
core branch
Intel VT-d:
- Use try_cmpxchg64() instead of cmpxchg64() when updating pte
- Use READ_ONCE() to read volatile descriptor status
- Remove support for handling Execute-Requested requests
- Avoid calling iommu_domain_alloc()
- Minor fixes and refactoring
Qualcomm MSM:
- Updates to the device-tree bindings"
* tag 'iommu-updates-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (72 commits)
iommu/tegra-smmu: Pass correct fwnode to iommu_fwspec_init()
iommu/vt-d: Fix identity map bounds in si_domain_init()
iommu: Move IOMMU_DIRTY_NO_CLEAR define
dt-bindings: iommu: Convert msm,iommu-v0 to yaml
iommu/vt-d: Fix aligned pages in calculate_psi_aligned_address()
iommu/vt-d: Limit max address mask to MAX_AGAW_PFN_WIDTH
docs: iommu: Remove outdated Documentation/userspace-api/iommu.rst
arm64: dts: fvp: Enable PCIe ATS for Base RevC FVP
iommu/of: Support ats-supported device-tree property
dt-bindings: PCI: generic: Add ats-supported property
iommu: Remove iommu_fwspec ops
OF: Simplify of_iommu_configure()
ACPI: Retire acpi_iommu_fwspec_ops()
iommu: Resolve fwspec ops automatically
iommu/mediatek-v1: Clean up redundant fwspec checks
RDMA/usnic: Use iommu_paging_domain_alloc()
wifi: ath11k: Use iommu_paging_domain_alloc()
wifi: ath10k: Use iommu_paging_domain_alloc()
drm/msm: Use iommu_paging_domain_alloc()
vhost-vdpa: Use iommu_paging_domain_alloc()
...
API:
- Test setkey in no-SIMD context.
- Add skcipher speed test for user-specified algorithm.
Algorithms:
- Add x25519 support on ppc64le.
- Add VAES and AVX512 / AVX10 optimized AES-GCM on x86.
- Remove sm2 algorithm.
Drivers:
- Add Allwinner H616 support to sun8i-ce.
- Use DMA in stm32.
- Add Exynos850 hwrng support to exynos.
-----BEGIN PGP SIGNATURE-----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=x80X
-----END PGP SIGNATURE-----
Merge tag 'v6.11-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Test setkey in no-SIMD context
- Add skcipher speed test for user-specified algorithm
Algorithms:
- Add x25519 support on ppc64le
- Add VAES and AVX512 / AVX10 optimized AES-GCM on x86
- Remove sm2 algorithm
Drivers:
- Add Allwinner H616 support to sun8i-ce
- Use DMA in stm32
- Add Exynos850 hwrng support to exynos"
* tag 'v6.11-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (81 commits)
hwrng: core - remove (un)register_miscdev()
crypto: lib/mpi - delete unnecessary condition
crypto: testmgr - generate power-of-2 lengths more often
crypto: mxs-dcp - Ensure payload is zero when using key slot
hwrng: Kconfig - Do not enable by default CN10K driver
crypto: starfive - Fix nent assignment in rsa dec
crypto: starfive - Align rsa input data to 32-bit
crypto: qat - fix unintentional re-enabling of error interrupts
crypto: qat - extend scope of lock in adf_cfg_add_key_value_param()
Documentation: qat: fix auto_reset attribute details
crypto: sun8i-ce - add Allwinner H616 support
crypto: sun8i-ce - wrap accesses to descriptor address fields
dt-bindings: crypto: sun8i-ce: Add compatible for H616
hwrng: core - Fix wrong quality calculation at hw rng registration
hwrng: exynos - Enable Exynos850 support
hwrng: exynos - Add SMC based TRNG operation
hwrng: exynos - Implement bus clock control
hwrng: exynos - Use devm_clk_get_enabled() to get the clock
hwrng: exynos - Improve coding style
dt-bindings: rng: Add Exynos850 support to exynos-trng
...
The new HAVE_PWRCTL option is defined in the PCI subsystem, so
selecting it unconditionally when PCI is disabled causes a harmless
warning:
WARNING: unmet direct dependencies detected for HAVE_PWRCTL
Depends on [n]: PCI [=n]
Selected by [y]:
- ARCH_QCOM [=y]
Add 'if PCI' in the qualcomm platform to hide the warning.
Fixes: ed70aaac7c ("Kconfig: reduce the amount of power sequencing noise")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Up until now, the function graph tracer could only have a single user
attached to it. If another user tried to attach to the function graph
tracer while one was already attached, it would fail. Allowing function
graph tracer to have more than one user has been asked for since 2009, but
it required a rewrite to the logic to pull it off so it never happened.
Until now!
There's three systems that trace the return of a function. That is
kretprobes, function graph tracer, and BPF. kretprobes and function graph
tracing both do it similarly. The difference is that kretprobes uses a
shadow stack per callback and function graph tracer creates a shadow stack
for all tasks. The function graph tracer method makes it possible to trace
the return of all functions. As kretprobes now needs that feature too,
allowing it to use function graph tracer was needed. BPF also wants to
trace the return of many probes and its method doesn't scale either.
Having it use function graph tracer would improve that.
By allowing function graph tracer to have multiple users allows both
kretprobes and BPF to use function graph tracer in these cases. This will
allow kretprobes code to be removed in the future as it's version will no
longer be needed. Note, function graph tracer is only limited to 16
simultaneous users, due to shadow stack size and allocated slots.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZpbWlxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qgtvAP9jxmgEiEhz4Bpe1vRKVSMYK6ozXHTT
7MFKRMeQqQ8zeAEA2sD5Zrt9l7zKzg0DFpaDLgc3/yh14afIDxzTlIvkmQ8=
=umuf
-----END PGP SIGNATURE-----
Merge tag 'ftrace-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull ftrace updates from Steven Rostedt:
"Rewrite of function graph tracer to allow multiple users
Up until now, the function graph tracer could only have a single user
attached to it. If another user tried to attach to the function graph
tracer while one was already attached, it would fail. Allowing
function graph tracer to have more than one user has been asked for
since 2009, but it required a rewrite to the logic to pull it off so
it never happened. Until now!
There's three systems that trace the return of a function. That is
kretprobes, function graph tracer, and BPF. kretprobes and function
graph tracing both do it similarly. The difference is that kretprobes
uses a shadow stack per callback and function graph tracer creates a
shadow stack for all tasks. The function graph tracer method makes it
possible to trace the return of all functions. As kretprobes now needs
that feature too, allowing it to use function graph tracer was needed.
BPF also wants to trace the return of many probes and its method
doesn't scale either. Having it use function graph tracer would
improve that.
By allowing function graph tracer to have multiple users allows both
kretprobes and BPF to use function graph tracer in these cases. This
will allow kretprobes code to be removed in the future as it's version
will no longer be needed.
Note, function graph tracer is only limited to 16 simultaneous users,
due to shadow stack size and allocated slots"
* tag 'ftrace-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (49 commits)
fgraph: Use str_plural() in test_graph_storage_single()
function_graph: Add READ_ONCE() when accessing fgraph_array[]
ftrace: Add missing kerneldoc parameters to unregister_ftrace_direct()
function_graph: Everyone uses HAVE_FUNCTION_GRAPH_RET_ADDR_PTR, remove it
function_graph: Fix up ftrace_graph_ret_addr()
function_graph: Make fgraph_update_pid_func() a stub for !DYNAMIC_FTRACE
function_graph: Rename BYTE_NUMBER to CHAR_NUMBER in selftests
fgraph: Remove some unused functions
ftrace: Hide one more entry in stack trace when ftrace_pid is enabled
function_graph: Do not update pid func if CONFIG_DYNAMIC_FTRACE not enabled
function_graph: Make fgraph_do_direct static key static
ftrace: Fix prototypes for ftrace_startup/shutdown_subops()
ftrace: Assign RCU list variable with rcu_assign_ptr()
ftrace: Assign ftrace_list_end to ftrace_ops_list type cast to RCU
ftrace: Declare function_trace_op in header to quiet sparse warning
ftrace: Add comments to ftrace_hash_move() and friends
ftrace: Convert "inc" parameter to bool in ftrace_hash_rec_update_modify()
ftrace: Add comments to ftrace_hash_rec_disable/enable()
ftrace: Remove "filter_hash" parameter from __ftrace_hash_rec_update()
ftrace: Rename dup_hash() and comment it
...
Kconfig will ask the user twice about power sequencing: once for the QCom
WCN power sequencing driver and then again for the PCI power control
driver using it.
Let's automate the selection of PCI_PWRCTL by introducing a new hidden
symbol: HAVE_PWRCTL which should be selected by all platforms that have
the need to include PCI power control code (right now: only ARCH_QCOM).
The pwrseq-based PCI pwrctl driver itself will then be selected by the
drivers binding to devices that may require external handling of the
power-up sequence (currently: ath11k and ath12k) based on the value
of HAVE_PWRCTL.
Make all PCI pwrctl Kconfig symbols hidden so that no questions are
asked during configuration.
Fixes: 4565d2652a ("PCI/pwrctl: Add PCI power control core code")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Closes: https://lore.kernel.org/lkml/CAHk-=wjWc5dzcj2O1tEgNHY1rnQW63JwtuZi_vAZPqy6wqpoUQ@mail.gmail.com/
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> # drivers/net/wireless/ath
Link: https://lore.kernel.org/r/20240717142803.53248-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
patchsets (devmem among them) did not make it in time.
Core & protocols
----------------
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT.
- Use flex array for netdevice priv area, ensure its cache alignment.
- Add a sysctl knob to allow user to specify a default rto_min at socket
init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful.
- Support scheduling transmission of packets based on CLOCK_TAI.
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned off
using cpusets.
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address.
- Allow configuration of multipath hash seed, to both allow synchronizing
hashing of two routers, and preventing partial accidental sync.
- Improve TCP compliance with RFC 9293 for simultaneous connect().
- Support sending NAT keepalives in IPsec ESP in UDP states. Userspace
IKE daemon had to do this before, but the kernel can better keep
track of it.
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled.
- Introduce IPPROTO_SMC for selecting SMC when socket is created.
- Allow UDP GSO transmit from devices with no checksum offload.
- openvswitch: add packet sampling via psample, separating the sampled
traffic from "upcall" packets sent to user space for forwarding.
- nf_tables: shrink memory consumption for transaction objects.
Things we sprinkled into general kernel code
--------------------------------------------
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver
for QCA6390).
- Add IRQ information in sysfs for auxiliary bus.
- Introduce guard definition for local_lock.
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures.
BPF
---
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered.
- Add new kfuncs for a generic, open-coded bits iterator.
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head.
- Support resilient split BTF which cuts down on duplication and makes
BTF as compact as possible WRT BTF from modules.
- Add support for dumping kfunc prototypes from BTF which enables both
detecting as well as dumping compilable prototypes for kfuncs.
- riscv64 BPF JIT improvements in particular to add 12-argument support
for BPF trampolines and to utilize bpf_prog_pack for the latter.
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs.
Driver API
----------
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose.
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits.
- Track additional RSS contexts in the core, make sure configuration
changes don't break them.
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated ESP
data paths.
- Support updating firmware on SFP modules.
Tests and tooling
-----------------
- mptcp: use net/lib.sh to manage netns.
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints.
- openvswitch: make test self-contained (don't depend on OvS CLI tools).
Drivers
-------
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead
and skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps
to catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead of
in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=opz8
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Not much excitement - a handful of large patchsets (devmem among them)
did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at
socket init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow
synchronizing hashing of two routers, and preventing partial
accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states.
Userspace IKE daemon had to do this before, but the kernel can
better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the
sampled traffic from "upcall" packets sent to user space for
forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head
- Support resilient split BTF which cuts down on duplication and
makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables
both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument
support for BPF trampolines and to utilize bpf_prog_pack for the
latter
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration
changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI
tools)
Drivers:
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead and
skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps to
catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead
of in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
tcp: Replace strncpy() with strscpy()
wifi: ath12k: fix build vs old compiler
tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
eth: fbnic: Add L2 address programming
eth: fbnic: Add basic Rx handling
eth: fbnic: Add basic Tx handling
eth: fbnic: Add link detection
eth: fbnic: Add initial messaging to notify FW of our presence
eth: fbnic: Implement Rx queue alloc/start/stop/free
eth: fbnic: Implement Tx queue alloc/start/stop/free
eth: fbnic: Allocate a netdevice and napi vectors with queues
eth: fbnic: Add FW communication mechanism
eth: fbnic: Add message parsing for FW messages
eth: fbnic: Add register init to set PCIe/Ethernet device config
eth: fbnic: Allocate core device specific structures and devlink interface
eth: fbnic: Add scaffolding for Meta's NIC driver
PCI: Add Meta Platforms vendor ID
net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
...
Most of this is part of my ongoing work to clean up the system call
tables. In this bit, all of the newer architectures are converted to
use the machine readable syscall.tbl format instead in place of complex
macros in include/uapi/asm-generic/unistd.h.
This follows an earlier series that fixed various API mismatches
and in turn is used as the base for planned simplifications.
The other two patches are dead code removal and a warning fix.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmaVB1cACgkQYKtH/8kJ
UicMqxAAnYKOxfjoMIhYYK6bl126wg/vIcDcjIR9cNWH21Nhn3qxn11ZXau3S7xv
3l/HreEhyEQr4gC2a70IlXyHUadYOlrk+83OURrunWk1oKPmZlMKcfPVbtp8GL7x
PUNXQfwM1XZLveKwufY24hoZdwKC+Y/5WLc1t0ReznJuAqgeO2rM9W5dnV5bAfCp
he3F5hFcr196Dz3/GJjJIWrY+cbwfmZWsNtj1vFTL5/r/LuCu8HTkqhsGj8tE5BJ
NGVEEXbp5eaVTCIGqJWhnuZcsnKN9kM51M7CtdwWf8OTckUVuJap5OsDVKQkWkGl
bLPbd2jhDltph0sah51hAIvv4WdkThW76u9FRW7KR3fo7ra67eF7l5j7wc1lE2JB
GwLJ1X56Bxe1GhvvNTlDmb7DrnlP/DMPuRv3Z6xyH6l8iZ2pMGlnAxuw6Bs1s6Y5
WSs36ZpnS0ctgjfx37ZITsZSvbKFPpQFJP4siwS8aRNv/NFALNNdFyOCY5lNzspZ
0dxwjn6/7UpHE4MKh6/hvCg2QwupXXBTRytibw+75/rOsR+EYlmtuONtyq2sLUHe
ktJ5pg+8XuZm27+wLffuluzmY7sv2F8OU4cTYeM60Ynmc6pRzwUY6/VhG52S1/mU
Ua4VgYIpzOtlLrYmz5QTWIZpdSFSVbIc/3pLriD6hn4Mvg+BwdA=
=XOhL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"Most of this is part of my ongoing work to clean up the system call
tables. In this bit, all of the newer architectures are converted to
use the machine readable syscall.tbl format instead in place of
complex macros in include/uapi/asm-generic/unistd.h.
This follows an earlier series that fixed various API mismatches and
in turn is used as the base for planned simplifications.
The other two patches are dead code removal and a warning fix"
* tag 'asm-generic-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
vmlinux.lds.h: catch .bss..L* sections into BSS")
fixmap: Remove unused set_fixmap_offset_io()
riscv: convert to generic syscall table
openrisc: convert to generic syscall table
nios2: convert to generic syscall table
loongarch: convert to generic syscall table
hexagon: use new system call table
csky: convert to generic syscall table
arm64: rework compat syscall macros
arm64: generate 64-bit syscall.tbl
arm64: convert unistd_32.h to syscall.tbl format
arc: convert to generic syscall table
clone3: drop __ARCH_WANT_SYS_CLONE3 macro
kbuild: add syscall table generation to scripts/Makefile.asm-headers
kbuild: verify asm-generic header list
loongarch: avoid generating extra header files
um: don't generate asm/bpf_perf_event.h
csky: drop asm/gpio.h wrapper
syscalls: add generic scripts/syscall.tbl
The majority of the updates here are Dmitry Torokhov's cleanups
for platform code in the pxa and tegra platforms, changing custom
platform_data structures into DT-compatible software node declarations.
The other updates are for the MAINTAINERS file, correcting some
stale or missing entries.
-----BEGIN PGP SIGNATURE-----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=/EgX
-----END PGP SIGNATURE-----
Merge tag 'soc-arm-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull arm SoC platform updates from Arnd Bergmann:
"The majority of the updates here are Dmitry Torokhov's cleanups for
platform code in the pxa and tegra platforms, changing custom
platform_data structures into DT-compatible software node
declarations.
The other updates are for the MAINTAINERS file, correcting some stale
or missing entries"
* tag 'soc-arm-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: pxa: fix build breakage on PXA3xx
ti: omap: MAINTAINERS: move Benoît Cousson to CREDITS
amazon: MAINTAINERS: change to odd fixes and Tsahee Zidenberg to CREDITS
MAINTAINERS: thead: add git tree
ARM: spitz: Use software nodes for the ADS7846 touchscreen
ARM: spitz: Use software nodes to describe LED GPIOs
ARM: spitz: Use software nodes to describe MMC GPIOs
ARM: spitz: Use software nodes to describe LCD GPIOs
ARM: spitz: Use software nodes to describe audio GPIOs
ARM: spitz: Use software nodes to describe SPI CS lines
ARM: spitz: Simplify instantiating SPI controller
ARM: pxa/gumstix: convert vbus gpio to use software nodes
ARM: pxa: consolidate GPIO chip platform data
ARM: spitz: fix GPIO assignment for backlight
ARM: tegra: paz00: Use software nodes to describe GPIOs for WiFi rfkill
MAINTAINERS: ARM: airoha: add entry to cover Airoha SoC
bus: vexpress-config: Add missing MODULE_DESCRIPTION() macro
arm64: layerscape: remove redundant EDAC_SUPPORT selection
dt-bindings: arm: Remove obsolete RTSM DCSCB binding
arm: vexpress: Remove obsolete RTSM DCSCB support
The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to
the MT7981 Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv
boards and eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops
based on the Qualcomm x1e80100 (Snapdragon X1 Elite) chip,
the Asus Vivobook S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices
from Samsung, Motorola and LG, as well as a wireless router
and some reference designs
- Six NXP i.MX based machines, mostly industrial boards along
with some reference designs
- Mediatek sees some interesting Filogic based routers
including the "OpenWRT One", a few new Chromebooks as
well as single-board computers.
- Four machines from Solidrun based on Marvell cn913x,
replacing the older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board
computers including some interesting ones based on the
rk3588 chip like the ROCK 5 ITX board and the CM3588
with its four NVMe slots
- The RISC-V boards are all single-board computers based on
Starfive JH7110, Microchip MPFS and Allwinner D1, which all
had similar boards already
There are also a lot of updates to already supported machines,
notably for the TI K3, Rockchips, Freescale and of course
Qualcomm platforms.
-----BEGIN PGP SIGNATURE-----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=xGqj
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are farily small maintenance
changes, either addressing minor mistakes or enabling additional hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and a
"shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a platform
driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some
code refactoring and new features.
-----BEGIN PGP SIGNATURE-----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=ChcR
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are fairly small maintenance
changes, either addressing minor mistakes or enabling additional
hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and
a "shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a
platform driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some code
refactoring and new features"
* tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (122 commits)
firmware: turris-mox-rwtm: Initialize completion before mailbox
firmware: turris-mox-rwtm: Fix checking return value of wait_for_completion_timeout()
firmware: turris-mox-rwtm: Do not complete if there are no waiters
MAINTAINERS: drop riscv list from cache controllers
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
bus: sunxi-rsb: Constify struct regmap_bus
soc: sunxi: sram: Constify struct regmap_config
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: Depend on OF
soc: samsung: exynos-pmu: add support for PMU_ALIVE non atomic registers
arm64: stm32: enable scmi regulator for stm32
firmware: qcom: tzmem: blacklist more platforms for SHM Bridge
soc: qcom: wcnss: simplify with cleanup.h
soc: qcom: pdr: simplify with cleanup.h
soc: qcom: ocmem: simplify with cleanup.h
soc: qcom: mdt_loader: simplify with cleanup.h
soc: qcom: llcc: simplify with cleanup.h
firmware: qcom: tzmem: simplify returning pointer without cleanup
soc: qcom: socinfo: Add PM6350 PMIC
arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
...
- Enable halt poll shrinking by default, as Intel found it to be a clear win.
- Setup empty IRQ routing when creating a VM to avoid having to synchronize
SRCU when creating a split IRQCHIP on x86.
- Rework the sched_in/out() paths to replace kvm_arch_sched_in() with a flag
that arch code can use for hooking both sched_in() and sched_out().
- Take the vCPU @id as an "unsigned long" instead of "u32" to avoid
truncating a bogus value from userspace, e.g. to help userspace detect bugs.
- Mark a vCPU as preempted if and only if it's scheduled out while in the
KVM_RUN loop, e.g. to avoid marking it preempted and thus writing guest
memory when retrieving guest state during live migration blackout.
- A few minor cleanups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEKTobbabEP7vbhhN9OlYIJqCjN/0FAmaRuOYACgkQOlYIJqCj
N/1UnQ/8CI5Qfr+/0gzYgtWmtEMczGG+rMNpzD3XVqPjJjXcMcBiQnplnzUVLhha
vlPdYVK7vgmEt003XGzV55mik46LHL+DX/v4hI3HEdblfyCeNLW3fKEWVRB44qJe
o+YUQwSK42SORUp9oXuQINxhA//U9EnI7CQxlJ8w8wenv5IJKfIGr01DefmfGPAV
PKm9t6WLcNqvhZMEyy/zmzM3KVPCJL0NcwI97x6sHxFpQYIDtL0E/VexA4AFqMoT
QK7cSDC/2US41Zvem/r/GzM/ucdF6vb9suzZYBohwhxtVhwJe2CDeYQZvtNKJ1U7
GOHPaKL6nBWdZCm/yyWbbX2nstY1lHqxhN3JD0X8wqU5rNcwm2b8Vfyav0Ehc7H+
jVbDTshOx4YJmIgajoKjgM050rdBK59TdfVL+l+AAV5q/TlHocalYtvkEBdGmIDg
2td9UHSime6sp20vQfczUEz4bgrQsh4l2Fa/qU2jFwLievnBw0AvEaMximkSGMJe
b8XfjmdTjlOesWAejANKtQolfrq14+1wYw0zZZ8PA+uNVpKdoovmcqSOcaDC9bT8
GO/NFUvoG+lkcvJcIlo1SSl81SmGLosijwxWfGvFAqsgpR3/3l3dYp0QtztoCNJO
d3+HnjgYn5o5FwufuTD3eUOXH4AFjG108DH0o25XrIkb2Kymy0o=
=BalU
-----END PGP SIGNATURE-----
Merge tag 'kvm-x86-generic-6.11' of https://github.com/kvm-x86/linux into HEAD
KVM generic changes for 6.11
- Enable halt poll shrinking by default, as Intel found it to be a clear win.
- Setup empty IRQ routing when creating a VM to avoid having to synchronize
SRCU when creating a split IRQCHIP on x86.
- Rework the sched_in/out() paths to replace kvm_arch_sched_in() with a flag
that arch code can use for hooking both sched_in() and sched_out().
- Take the vCPU @id as an "unsigned long" instead of "u32" to avoid
truncating a bogus value from userspace, e.g. to help userspace detect bugs.
- Mark a vCPU as preempted if and only if it's scheduled out while in the
KVM_RUN loop, e.g. to avoid marking it preempted and thus writing guest
memory when retrieving guest state during live migration blackout.
- A few minor cleanups
