The Variscite VAR-SOM-MX8MM System-on-Module cannot be used alone
without motherboard, so drop the top-level compatible field to avoid any
false impression that such usage is possible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add RTC PCF2131 node for new ls1088ardb board..
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unnecessary comments. The Colibri-iMX8X doesn't support FlexCAN,
and the GPU is already enabled in the SOC dtsi.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change enet0_lpcg to get the clock value needed in Colibri-iMX8X for
100mbps ethernet.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add adma_pwm node for Colibri-iMX8X carrier boards.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable VPU on Colibri-iMX8X.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB3803 HUB, this is required for Bluetooth and USB
functionalities.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add audio support for Colibri-iMX8X sound card.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add fxl6408 gpio expander, this is required for Wi-Fi, Bluetooth and USB
functionalities.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add adc nodes for analog inputs support for all Colibri-iMX8X carrier
boards.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB HOST and OTG support to Colibri-iMX8X carrier boards.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add i2c node in mipi[0,1] subystem for imx8qm-mek.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pwm[0,1] and i2c[0,1] in lvds subsystem.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add two cm4 remote-proc and related memory regions.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW7905 was renamed to GW7500 before production release.
While we typically do not change compatibles, the GW7905 was never
released before its product name was changed to a GW7500.
The use the the 'xx' wildcard is to denote the fact that this
device-tree can support range of board models from GW7500 to GW7599 as
has been done historically with the Gateworks baseboards to support
various build customizatoins based on the same PCB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
J702 on i.MX93 11x11 EVK base board is a 40-pin connector labelled
"LVDS". This connector supports PWM backlight with default 12V power
supply and ADP5585 PWM controller. Add support for the backlight.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Mini PCIe slot.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
J17 on i.MX8mp EVK base board is a HDMI type A connector.
It connects with i.MX8mp HDMI PHY. Add support for it.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The merge of imx-spdif driver into fsl-asoc-card brought
new DT properties that can be used with the "fsl,imx-audio-spdif"
compatible:
* The "spdif-controller" property from imx-spdif is named "audio-cpu"
in fsl-asoc-card.
* fsl-asoc-card uses codecs explicitly declared in DT
with "audio-codec".
With an S/PDIF, codec drivers spdif_transmitter and
spdif_receiver should be used.
Driver imx-spdif used instead the dummy codec and a pair of
boolean properties, "spdif-in" and "spdif-out".
While backward compatibility is kept to support properties
"spdif-controller", "spdif-in" and "spdif-out", using new properties has
several benefits:
* "audio-cpu" and "audio-codec" are more generic names reflecting
that the fsl-asoc-card driver supports multiple hardware.
They are properties already used by devices using the
fsl-asoc-card driver.
They are also similar to properties of simple-card: "cpu" and "codec".
* "spdif-in" and "spdif-out" imply the use of the dummy codec in the
driver. However, there are already two codec drivers for the S/PDIF,
spdif_transmitter and spdif_receiver.
It is better to declare S/PDIF Tx and Rx devices in a DT, and then
reference them with "audio-codec" than using the dummy codec.
For those reasons, this commit updates in-tree DTs to use the new
properties:
* Rename "spdif-controller" property to "audio-cpu".
* Declare S/PDIF transmitter and/or receiver devices, and use them with
the "audio-codec" property instead of "spdif-out" and/or "spdif-in".
These modifications were tested only on an imx8mn-evk board.
Note that out-of-tree and old DTs are still supported.
Signed-off-by: Elinor Montmasson <elinor.montmasson@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a second HDMI connector on the baseboard which is routed
to the DW HDMI bridge through the PVI to the LCDIF3 and requires the
HDMI PHY to be enabled too.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc, DVDD-supply and DOVDD-supply is required
properties. Add these to fix below warning:
arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dtb: camera@10: 'DVDD-supply' is a required proper
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove fallback comaptible string arm,cortex-a9-gic to fix below warning:
/home/lizhi/source/linux-upstream-dts/arch/arm64/boot/dts/freescale/s32v234-evb.dtb: interrupt-controller@7d001000: compatible: 'oneOf' conditional failed, one must be fixed:
['arm,cortex-a15-gic', 'arm,cortex-a9-gic'] is too long
/home/lizhi/source/linux-upstream-dts/arch/arm64/boot/dts/freescale/s32v234-evb.dtb: interrupt-controller@7d001000: compatible: 'oneOf' conditional failed, one must be fixed:
['arm,cortex-a15-gic', 'arm,cortex-a9-gic'] is too long
'nvidia,tegra210-agic' was expected
'arm,cortex-a15-gic' is not one of ['nvidia,tegra186-agic', 'nvidia,tegra194-agic', 'nvidia,tegra234-agic']
'arm,gic-400' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change to low case for hex value to fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dtb: flash@0:
partitions: Unevaluated properties are not allowed ('partition@5C0000' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add vddl and vana for sensor@10 to fix below warning:
arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-imx219.dtb:
sensor@10: 'VANA-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binging doc usb/ti,usb8041.yaml and in
drivers/usb/misc/onboard_usb_dev.h
ti_tusb8041_data = { .supply_names = { "vdd" },};
It should vdd-supply instead vcc-supply.
Fixes: 04b77e0124 ("arm64: dts: freescale: add fsl-lx2160a-mblx2160a board")
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add #address-cells and #size-cells for gsc@20 node to fix below warning:
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dtb:
gsc@20: '#address-cells' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add A(CP, DB, DC, MIC)VDD-supply for wm8904 to fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dtb:
audio-codec@1a: 'AVDD-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename node name mdio-mux-emi<n>@<addr> to mdio-mux@<addr>.
Fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dtb: board-control@2,0: 'mdio-mux-emi1@54' does not match any of the regexes: '^mdio-mux@[a-f0-9,]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/board/fsl,fpga-qixis.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move fixed clock "clock-sc16is7x" from dspi to root node to fix below
warning:
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb:
serial@0: Unevaluated properties are not allowed ('clock-sc16is7xx' was unexpected)
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move fsl,ls1043a-qdma ahead fallback string fsl,ls1021a-qdma.
Fix warning:
dma-controller@8380000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,ls1021a-qdma', 'fsl,ls1043a-qdma'] is too long
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove undocument 'slot' property. It is default 0 at driver. We can remove
it safely.
Fix below warning:
arch/arm64/boot/dts/freescale/imx8dx-colibri-iris.dtb: jpegdec@58400000:
'slot' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx93 pad integrate has one issue, refer to ERR052021:
ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low
drive mode and nominal mode
Description:
uSDHC PADs have one integration issue.
When CMD/DATA lines direction change from output to input, uSDHC
controller begin sampling, the integration issue will make input
enable signal from uSDHC propagated to the PAD with a long delay,
thus the new input value on the pad comes to uSDHC lately. The
uSDHC sampled the old input value and the sampling result is wrong.
Workaround:
Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will
propagate input to uSDHC with no delay, so correct value is sampled.
This issue will wrongly trigger the start bit when sample the USDHC
command response, cause the USDHC trigger command CRC/index/endbit
error, which will finally impact the tuning pass window, espically
will impact the standard tuning logic, and can't find a correct delay
cell to get the best timing.
This follows changes made for i.MX93 EVK with commit bb89601282 ("arm64:
dts: imx93-11x11-evk: set SION for cmd and data pad of USDHC")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Provide GPIO line names for userspace usage, e.g. libgpiod.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They are used by systemd to rename network interfaces to predictable
interface names, e.g. end0 & end1.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- add missing (and currently unused) pad groups
- assign muxed GPIO pads for X1 to gpio2 node
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- disable PU/PD if already done with external resistors
- do not configure Schmitt Trigger for outputs
- do not configure DSE / FSEL for inputs
Pad config changes suggested by hardware team.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IRQ lines from devices on SoM are connected to CPU GPIO on
this mainboard.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Provide GPIO line names for userspace usage, e.g. libgpiod.
While at it, correct the line-name property for ENET[1,2]_INT# gpio hog
and LCD_BLT_EN.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They are used by systemd to rename network interfaces to predictable
interface names, e.g. end0 & end1.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- add missing (and currently unused) pad groups
- assign muxed GPIO pads for X1 to gpio2 node
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds muxing and configuration of the irq output of the temp
sensor on TQMa93xx that is connected to a GPIO line on MBa93xxLA
While at it, add comment for RTC_EVENT for pcf85063 since the IRQ line
of both devices on SoM are routed to CPU GPIO on MBa93xxLA.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LPSPI6 features a NAFE13388 analog frontend.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- disable PU/PD if already done with external resistors
- do not configure Schmitt Trigger for outputs
- do not configure DSE / FSEL for inputs
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
