Fix the warning: [-Werror=-Wframe-larger-than=]
drivers/usb/misc/usbtest.c: In function 'test_queue':
drivers/usb/misc/usbtest.c:2148:1:
warning: the frame size of 1232 bytes is larger than 1024 bytes
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/ffa85702-86ab-48d7-4da2-2efcc94b05d3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of packet number within microframe is different between
high-speed and super-speed endpoint, we add support for super-speed
in this patch.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel would like to have all stack VLA usage removed[1]. We
already have a pre-processor constant defined MAX_SGLEN. We can use
this instead of the variable param-sglen.
[1]: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear Feature Endpoint Halt should reset the data toggle even if the
endpoint isn't halted. Host should manage to clear the host side data
toggle to keep in sync with the device.
Test by sending a "3 data packet URB" before and after clearing the halt.
this should create a toggle sequence with two consecutive DATA0 packets.
A successful test sequence looks like this
ClearFeature(ENDPOINT_HALT) - initial toggle clear
DATA0 (max packet sized)
DATA1 (max packet sized)
DATA0 (zero length packet)
ClearFeature(ENDPOINT_HALT) - resets toggle
DATA0 (max packet sized), if clear halt fails then toggle is DATA1
DATA1 (max packet sized)
DATA0 (zero length packet)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
This new helper is a simple wrapper around usb_get_status(). This
patch is in preparation to adding support for fetching PTM_STATUS
types. No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Also adds missing call to
destroy_timer_on_stack();
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the usbtest driver encounters a device with an IN bulk endpoint but
no OUT bulk endpoint, it will try to dereference a NULL pointer
(out->desc.bEndpointAddress). The problem can be solved by adding a
missing test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There used to be a test against "if (param->sglen > MAX_SGLEN)" but it
was removed during a refactor. It leads to an integer overflow and a
stack overflow in test_queue() if we try to create a too large urbs[]
array on the stack.
There is a second integer overflow in test_queue() as well if
"param->iterations" is too high. I don't immediately see that it's
harmful but I've added a check to prevent it and silence the static
checker warning.
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Code refactoring to make the flow easier to follow.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for retval being less than zero is always true since
retval equal to -EPIPE at that point. Replace the existing
conditional with just return retval.
Detected with CoverityScan, CID#114349 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: stable@vger.kernel.org # 3.15+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern
Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 8b52490193 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing")
Cc: <stable@vger.kernel.org> # v2.6.18+
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb allocation will fail when usbtest_alloc_urb() tries to
allocate zero length buffer, but it doesn't need it in fact,
so just skips buffer allocation in the case.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timeval is deprecated and not y2038 safe. Its size also changes according
to 32 bit/ 64 bit compilation. Replace it with 32 and 64 bit versions of
its individual fields, giving two ioctls with different code values.
The two ioctls are necessary to maintain the 32 bit and 64 bit userspace
compatibility with a 64/32 bit kernel.
Change unsigned to __u32 types for a definitive userspace interface.
This is in accordance with the psABI that the unsigned type is always
32 bits.
Also use motonic timer instead of real time to ensure positive delta
values.
Refactor usbtest_ioctl for readability to isolate the handling of the
testing timing measurement.
The official testusb userspace tool can be changed in a separate patch
to reflect the __u32 changes as well. It can use the usbtest_param_32
struct, since 32 bit seconds is long enough for test durations.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the function of complicated_callback is not only used for iso
transfer, improve the error message to reflect it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bulk queue tests are used to show 'best performance' for bulk
transfer, we are often asked this question by users. The implementation
is the same with iso test, that is queue request at interrupt completion,
so we reuse the iso structures, and rename them as common one.
It's result should be very close to IC simulation, in order
to get that, the device side should also need to prepare enough
queue.
We have got the 'best performance' (IN: 41MB, OUT: 39MB) at i.mx platform
(USB2, ARM Cortex A9, stream mode need to enable) with below command:
Host side:
modprobe usbtest
./testusb -a -t 27 -g 64 -s 16384
./testusb -a -t 28 -g 64 -s 16384
Gadget side:
modprobe g_zero loopdefault=1 qlen=64 buflen=16384
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With this change, the host and gadget doesn't need to agree with transfer
length for comparing the data, since they doesn't know each other's
transfer size, but know max packet size.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
(Fixed the 'line over 80 characters warning' by Peter Chen)
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using the same data format "buf[j] = (u8)(i + j)" among
write, compare buf, and console output stage.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The element of urbs array will be initialized at below code
at once.
for (i = 0; i < param->sglen; i++) {
urbs[i] = iso_alloc_urb(udev, pipe, desc,
param->length, offset);
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate the size of urb pointer array according to testusb's
parameter sglen, and limits the length of sglen as MAX_SGLEN
(128 currently).
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The current code prints all wMaxPacketSize content at endpoint
descriptor, if there is a high speed, high bandwidth endpoint,
it may confuse the users, eg, if there are 3 transactions during
microframe, it will print "wMaxPacket 1400" for packet content.
This commit splits wMaxpacketSize and transaction numbers for
output messages.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.
This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:
Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two simple test cases for interrupt endpoints are added to the usbtest.c file.
These are simple non-queued interrupt IN and interrupt OUT transfers. Currently,
only gadget zero is capable of executing the interrupt EP test cases. However,
extending the same to other gadgets is extremely simple and can be done
on-demand.
The two new tests added are
- Test 25: To verify Interrupt OUT transfer
- Test 26: To verify Interrupt IN transfer
Since the default value of wMaxPacketSize is set as 1024, so interrupt
IN transfers must be specified with the size parameter = multiple of
1024. Otherwise the default value (512) in the usbtest application fails
the transfer. See [RUN 4] for sample logs
The application logs (usbtest) and corresponding kernel logs are as
following:
[Run 1]
./testusb -a -c 10 -s 2048 -t 26 -v 511
usbtest 7-1:3.0: TEST 26: read 2048 bytes 10 times
[Run 2]
./testusb -a -c 10 -s 1024 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1024 bytes 10 times
[Run 3]
./testusb -a -c 10 -s 1098 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1098 bytes 10 times
[Run 4 - Failure case scenario]
./testusb -a -t 26
unknown speed /dev/bus/usb/007/004 0
/dev/bus/usb/007/004 test 26 --> 75 (Value too large for defined data type)
usbtest 7-1:3.0: TEST 26: read 512 bytes 1000 times
usb 7-1: test26 failed, iterations left 999, status -75 (not 0)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In usbtest, tests 5 - 8 use the scatter-gather library in usbcore
without any sort of timeout. If there's a problem in the gadget or
host controller being tested, the test can hang.
This patch adds a 10-second timeout to the tests, so that they will
fail gracefully with an ETIMEDOUT error instead of hanging.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Huang Rui <ray.huang@amd.com>
Tested-by: Huang Rui <ray.huang@amd.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TEST 11 unlinks the URB read request for N times. When host and gadget
both initialize pattern 1 (mod 63) data series to do IN transfer, the
host side function should check the data buffer if it is as mod 63
series, because the data packet which host receivced will follow
pattern 1. So this patch adds this checking action.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected. Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.
[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Happy Holidays, Greg!
Here's four patches to be queued to usb-next for 3.14.
One adds a module parameter to the xHCI driver to allow users to enable
xHCI quirks without recompiling their kernel, which you've already said
is fine. The second patch is a bug fix for new usbtest code that's only
in usb-next. The third patch is simple cleanup.
The last patch is a non-urgent bug fix for xHCI platform devices. The
bug has been in the code since 3.9. You've been asking me to hold off
on non-urgent bug fixes after -rc4/-rc5, so it can go into usb-next, and
be backported to stable once 3.14 is out.
These have all been tested over the past week. I did run across one
oops, but it turned out to be a bug in 3.12, and therefore not related
to any of these patches.
Please queue these for usb-next and 3.14.
Thanks,
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJStMtLAAoJEBMGWMLi1Gc5uxMQAIXOL38n53yfNETU+DJMLaWB
+DY/RJjJ0zAZuRL9emOvR+BYEsQpd2q6aT3F2MryjJT/dhEKwJgHLTLOv0EQEWS7
dfLXX/NKNI+iRNyJkSATriytWMmMwv13kTXkreu99ZAw2PWWt7mM4BPHaWJ6sz5G
MjWS3v6LE59zjZatdzZyg4wlgUeNmO8cc4CV8YSqv0rFiVrKBL8IJsxwgQkWXI+2
J19hZcEpgeVMPo7aPlkMGoS1Ze9SxTviALBVLBWwwR028UfWCELFWsSFGVfJ6RgJ
/3DsE+jhQBn/1Y1o6hrlU/arDj7N/iJ3Gz5Ru5l+BtJw56fdaI/ToaHzzIDarONE
DGLiziDIknlSPsuX6X81kqXqROz1Zt624aqLipvqGCk0FMrLZz5BMaPEslkmW4Wb
/TQRX6KnTVzK4uMjv5yNVaGtnyoTStJeRE7dIF4/9e2YDLo4SCmm2Y9necr4C3Ls
7FzT8t6m9F74ZHAkmPpKFlEkYTYOy3yv/KBlhHF/OVFo9FAxAwUEY69QVrvhaHVX
GhLANc4NOuJb1eIwQarVkub2+lLI3N9zwEWliepKKUTQ8OTFDkDFM/+bwDHd4RzD
PO23wuFHVLj9N2BZbIAV2OkDyJLU2FOl+ZiEG6NUDXssihiZj4AVfIRiOU1c3EMc
g27X+N4FI2fnpqvAYq/a
=PRbx
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Cleanups, non-urgent fixes for 3.14.
Happy Holidays, Greg!
Here's four patches to be queued to usb-next for 3.14.
One adds a module parameter to the xHCI driver to allow users to enable
xHCI quirks without recompiling their kernel, which you've already said
is fine. The second patch is a bug fix for new usbtest code that's only
in usb-next. The third patch is simple cleanup.
The last patch is a non-urgent bug fix for xHCI platform devices. The
bug has been in the code since 3.9. You've been asking me to hold off
on non-urgent bug fixes after -rc4/-rc5, so it can go into usb-next, and
be backported to stable once 3.14 is out.
These have all been tested over the past week. I did run across one
oops, but it turned out to be a bug in 3.12, and therefore not related
to any of these patches.
Please queue these for usb-next and 3.14.
Thanks,
Sarah Sharp
In test_halt() we set an endpoint halt condition and return on halt verification
failure, then the enpoint will remain halted and all further tests related
to that enpoint will fail. This is because we don't tackle endpoint halt error condition
in any of the tests. To avoid that situation, make sure to clear the
halt condition before exiting test_halt().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without a timetout some tests e.g. test_halt() can remain stuck forever.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c952a8ba71 "usb: usbtest: add a
test case to support bos for queue control" will cause USB 2.01 and USB
2.10 devices with a BOS descriptor to fail case 15 of the control test.
The Link PM errata (released in 2007, updated in 2011) says:
"The value of the bcdUSB field in the standard USB 2.0 Device Descriptor
is used to indicate that the device supports the request to read the BOS
Descriptor (i.e. GetDescriptor(BOS)). Devices that support the BOS
descriptor must have a bcdUSB value of 0201H or larger."
The current code says that non-SuperSpeed devices *must* return -EPIPE,
as this comment shows:
/* sign of this variable means:
* -: tested code must return this (negative) error code
* +: tested code may return this (negative too) error code
*/
int expected = 0;
This means the test will fail with USB 2.01 and USB 2.10 devices that
provide a BOS descriptor. Change it to only require a stall response if
the USB device bcdUSB is less than 2.01.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Huang Rui <ray.huang@amd.com>
The commit "usb: usbtest: support bos descriptor test for usb 3.0"
introduced a test for bos descriptor. And USB 2.1 device also can be
checked. So this patch extends the test coverage to support USB 2.1 device.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.1 Link PM adds to use bits[1:15] according to USB 2.0 ECN Errata for
Link Power Management spec.
Bit Encoding
0 Reserved
1 LPM
2 BESL & Altemate HIRD definitions supported
3 Recommended Baseline BESL valid
4 Recommended Deep BESL valid
11:8 Recommended Baseline BESL value
15:12 Recommended Deep BESL value
31:16 Reserved
So fix the bit mask from 0x1e to 0xfffe.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 10 of usbtest module, it queues multiple control messages and
thereby tests control message queuing, protocol stalls, short reads, and
fault handling. And this patch add a test case to support queue BOS control
request for USB 3.0 SPEC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times.
Container ID descriptor is one of the generic device-level capbility
descriptors which added in section 9.6.2.3 of USB 3.0 spec.
This patch adds to support getting Container ID descriptor test scenario
for USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times.
SuperSpeed USB Device Capability descriptor is one of the generic
device-level capbility descriptors which added in section 9.6.2.2 of USB
3.0 spec.
This patch adds to support getting SuperSpeed USB Device Capability
descriptor test scenario for USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times.
USB2.0 Extension descriptor is one of the generic device-level capbility
descriptors which added in section 9.6.2.1 of USB 3.0 spec.
This patch adds to support getting usb2.0 extension descriptor test
scenario for USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times. This patch adds to support getting bos descriptor test scenario for
USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transfer type is isochronous, the other bits (bits 5..2) of
bmAttributes in endpoint descriptor might not be set zero. So it's better
to use usb_endpoint_type routine to mask bmAttributes with
USB_ENDPOINT_XFERTYPE_MASK to judge the transfter type later.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
