mthca_make_profile() returns the size in bytes of the HCA context
layout it creates, or a negative value if an error occurs. However,
the return value is declared as u64 and the memfree initialization
path casts this value to int to test if it is negative. This makes it
think incorrectly than an error has occurred if the context size
happens to be bigger than 2GB, since this turns into a negative int.
Fix this by having mthca_make_profile() return an s64 and testing
for an error by checking whether this 64-bit value itself is negative.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Pavel Emelyanov <xemul@openvz.org> mentioned in <http://lkml.org/lkml/2008/3/17/131>
that the task_struct->tgid field is about to become deprecated, so the
uses in the ehca driver need to be fixed up.
However, all the uses in ehca are for some object ownership checking
that is not really needed, and anyway is implementing a policy that
should be in common code rather than a low-level driver. So just
remove all the checks.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable use of 4KB MTU. Since the driver uses more pinned memory for
receive buffers when the 4KB MTU is enabled, whether or not the fabric
supports that MTU, add a "mtu4096" module parameter that can be used to
limit the MTU to 2KB when it is known that 4KB MTUs can't be used
anyway.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code was checking if units are present, but not that present units
were usable (link up, etc.)
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modern I/O buses like PCIe and HT can be configured for multiple speeds
and widths. When an ipath HCA seems to have lower than expected
performance, it is very useful to be able to display what the driver
thinks the bus speed is.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes some constants chip-specific, and makes some related
changes to prepare for supporting another HCA.
Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recent sparse versions and kernel cleanups knock down the false positive
rate of the ipath driver code to a point where having it be sparse clean
is worthwhile. Here we fixup the sparse warnings. Some of these warnings
(and the impetus to run sparse again) are due to work by Roland Dreier.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Arbel and Sinai devices support checksum generation and verification
of TCP and UDP packets for UD IPoIB messages. This patch checks if
the HCA supports this and sets the IB_DEVICE_UD_IP_CSUM capability
flag if it does. It implements support for handling the IB_SEND_IP_CSUM
send flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages. This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does. It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Ali Ayub <ali@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
__FUNCTION__ is gcc-specific, use __func__ instead.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow the compiler to optimize better and generate smaller code:
add/remove: 0/6 grow/shrink: 2/0 up/down: 1528/-1864 (-336)
function old new delta
.ehca_set_pagebuf 1344 2172 +828
.ehca_probe 2312 3012 +700
ehca_set_pagebuf_phys 24 - -24
ehca_set_pagebuf_fmr 24 - -24
ehca_init_device 24 - -24
.ehca_set_pagebuf_fmr 480 - -480
.ehca_set_pagebuf_phys 512 - -512
.ehca_init_device 800 - -800
Also this fixes warnings like:
drivers/infiniband/hw/ehca/ehca_mrmw.c:2015:5: warning: symbol 'ehca_set_pagebuf_fmr' was not declared. Should it be static?
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On some platforms, eg sparc64, dma_addr_t is not the same size as a
pointer, so printing dma_addr_t values by casting to void * and using
a %p format generates warnings. Fix this by casting to unsigned long
and using %lx instead. This fixes the warnings:
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_setup_virt_qp':
drivers/infiniband/hw/nes/nes_verbs.c:1047: warning: cast to pointer from integer of different size
drivers/infiniband/hw/nes/nes_verbs.c:1078: warning: cast to pointer from integer of different size
drivers/infiniband/hw/nes/nes_verbs.c:1078: warning: cast to pointer from integer of different size
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_reg_user_mr':
drivers/infiniband/hw/nes/nes_verbs.c:2657: warning: cast to pointer from integer of different size
Reported by Andrew Morton <akpm@linux-foundation.org>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
nes_unregister_ofa_device() dereferences the nesibdev pointer before
testing if it's NULL. Also, the test is doubly redundant because the
only caller of nes_unregister_ofa_device() is nes_destroy_ofa_device(),
which already tests if nesibdev is NULL. Remove the unnecessary test.
This was spotted by the Coverity checker (CID 2190).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct mlx4_interface.event() method was supposed to get an enum
mlx4_dev_event, but the driver code was actually passing in the
hardware enum mlx4_event values. Fix up the callers of
mlx4_dispatch_event() so that they pass in the right type of value,
and fix up the event method in mlx4_ib so that it can handle the enum
mlx4_dev_event values.
This eliminates the need for the subtype parameter to the event
method, so remove it.
This also fixes the sparse warning
drivers/net/mlx4/intf.c:127:48: warning: mixing different enum types
drivers/net/mlx4/intf.c:127:48: int enum mlx4_event versus
drivers/net/mlx4/intf.c:127:48: int enum mlx4_dev_event
Signed-off-by: Roland Dreier <rolandd@cisco.com>
None of the cqp_reqs_XXX counters were ever used anywhere, and neither
was the nics_per_function variable.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix
drivers/infiniband/hw/ipath/ipath_init_chip.c:526:10: warning: symbol 'val' shadows an earlier one
drivers/infiniband/hw/ipath/ipath_init_chip.c:473:6: originally declared here
by giving the second val a different name.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Arthur Jones <arthur.jones@qlogic.com>
There's no reason for the third parameter of ipath_count_units() to be
a u32 *, so change it to be an int * instead. This fixes the sparse
warning:
drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: warning: incorrect type in argument 3 (different signedness)
drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: expected unsigned int [usertype] *maxportsp
drivers/infiniband/hw/ipath/ipath_file_ops.c:1654:47: got int *<noident>
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix sparse warnings about pointer signedness by using a signed int when
calling idr_get_new_above().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Write tests for NULL pointers as
if (!ptr)
instead of
if (ptr == 0UL)
to fix sparse warnings.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Because of a typo in iwch_accept_cr(), the cxgb3 connection handling
code programs the hardware IRD (incoming RDMA read queue depth) with
the value that is passed in for the ORD (outgoing RDMA read queue
depth). In particular this means that if an application passes in IRD
> 0 and ORD = 0 (which is a completely sane and valid thing to do for
an app that expects only incoming RDMA read requests), then the
hardware will end up programmed with IRD = 0 and the app will fail in
a mysterious way.
Fix this by using "ep->ird" instead of "ep->ord" in the intended place.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the calculation of the MSS for RDMA connections: we need to
allow space in frames for a VLAN tag too.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reset the retry counter when we get a good RDMA_READ_RESPONSE_MIDDLE
packet. This fix will prevent the requester from reporting a retry
exceeded error too early.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
A work completion entry could be placed on the wrong completion
queue when an RC QP is placed in the error state.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the initialization of RC QPs, since we would rely on
the queue pair type (ibqp->qp_type) being set, but this field is only
initialized when we return from ipath_create_qp (it is initialized by
the user-level verbs library).
The fix is to not depend on this field to initialize the send and
the receive state of the RC QP.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There can be a case where the requester's rnr retry counter
(s_rnr_retry) is less than the number of rnr retries allowed per QP
(s_rnr_retry_cnt). This can happen if the s_rnr_retry counter is being
decremented and an ipath_query_qp call is issued during that time frame.
The fix is to always return the number of rnr retries allowed per QP
instead of the requester's rnr counter.
Found by code review.
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Subnet manager SetPortinfo messages distingush between changing the link
state (DOWN, ARM, ACTIVE) and the link physical state (POLL, SLEEP,
DISABLED). These are somewhat independent commands and affect when link
width and speed changes take effect. Without this patch, a link DOWN
physical state NOP command was causing the link width and speed settings
to take effect which should only happen when the link physical state is
goes down (either by a SMP or some link physical error like link errors
exceeding the threshold).
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cxbg3 driver is unnecessarily decreasing the number of CQ entries by
one when creating a CQ. This will cause the CQ not to have as many
entries as requested by the user if the user requests a power of 2 size.
Signed-off-by: Jon Mason <jon@opengridcomputing.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set cap.max_inline_data to the actual max inline data that the adapter
support, so that userspace apps see the right value returned.
Signed-off-by: Jon Mason <jon@opengridcomputing.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Interrupt moderation low threshold value was incorrectly triggering,
indicating that the threshold should be lowered.
The impact was the timer was likely to become 40usecs and get stuck
there. The biggest side effect was too many interrupts and nonoptimal
performance.
Signed-off-by: John Lacombe <jlacombe@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With commit ef19454b ("[LIB] crc32c: Keep intermediate crc state in
cpu order"), the behavior of crc32c changes on big-endian platforms.
Our algorithm expects the previous behavior; otherwise we have RDMA
connection establishment failure on big-endian platforms like powerpc.
Apply cpu_to_le32() to value returned by crc32c() to get the previous
behavior.
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Just delete the debugging statement so we don't use cqp_request after
freeing it. Adrian Bunk flagged this use-after-free issue spotted by
the Coverity checker.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix an off-by-one spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Adrian Bunk pointed out that a Coverity scan found some apparently
dead code in nes_verbs.c that really shouldn't have been dead.
The function nes_create_cq() was missing the assignment
err = 1;
just prior to an iteration that conditionally set err = 0 if a PBL was
found for a given virtual CQ. I also noticed we should have been
returning -EFAULT on a couple related error paths.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A single entry (addr 0x10001000, size 0x2000) will get converted to
page address 0x10000000 with a page size of 0x4000. The code as it
stands doesn't address the single buffer case, but in fact it allows
the subsequent single-buffer special case to be eliminated entirely.
Because the mask now includes the (page adjusted) starting and ending
addresses, the general case works for the single buffer case as well.
Signed-off-by: Bryan Rosenburg <rosnbrg@us.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When mthca_fmr_alloc() returns an error, it should free the MPT at the
index key, not mr->ibmr.lkey, since the lkey has been mangled by
hw_index_to_key() and no longer is the real index. This bug causes
corruption of the MPT table free bitmap when mthca_fmr_alloc() fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In nes_create_qp(), the test
if (nesqp->mmap_sq_db_index > NES_MAX_USER_WQ_REGIONS) {
is used to error out if the db_index is too large; however, if the
test doesn't trigger, then the index is used as
nes_ucontext->mmap_nesqp[nesqp->mmap_sq_db_index] = nesqp;
and mmap_nesqp is declared as
struct nes_qp *mmap_nesqp[NES_MAX_USER_WQ_REGIONS];
which leads to an array overrun if the index is exactly equal to
NES_MAX_USER_WQ_REGIONS. Fix this by bailing out if the index is
greater than or equal to NES_MAX_USER_WQ_REGIONS.
This was spotted by the Coverity checker (CID 2162).
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to account for the VLAN header size in nes_netdev_change_mtu()
and nes_netdev_init(). Also, add spin lock/unlock during VLAN RX
registration so only one process can assign VLAN group for a given
interface at a time.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only mask out MAC interrupt if necessary and re-enable on ifup. There
could be multiple netdevs going through the same MAC. MAC interrupts
should not be masked off until the last netdev is downed.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently mlx4_ib_fmr_alloc() calls mlx4_mr_enable() instead of
mlx4_fmr_enable(). The two functions are equivalent at the moment, but
this is not really correct (and the change is needed to fix a bug).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
