For station capabilities, e.g. TWT, we need to use the correct
link station instead of deflink. Switch the code to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The argument is unused except for NULL checking, but we already
do that anyway, so it's not needed. Remove the argument.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This requires a few more changes.
While at it, also add a warning to ieee80211_get_sband()
to avoid it being used when there are multiple links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we decide to stop tracking QoS/WMM parameters, then
this should be a per-link decision. Move the flag to
the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do the first adjustments in the client-side code to pass
the link pointer (instead of sdata) to most places etc.
This is just preparation, so the real MLO patches become
smaller.
Note that this isn't complete, notably there are still
quite a few references to sta->deflink and sta->sta.deflink.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the IEEE80211_STA_RESET_SIGNAL_AVE flag and use
a bool instead, but invert the polarity (now calling it
tracking_signal_avg) so we don't have to initialize it,
and put that into the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To prepare a bit more for MLO in the client code,
track the AP's address (for now only the BSSID, but
will track the AP MLD's address later) separately
from the per-link BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, expect the driver fully handles powersave handling,
including tracking whether or not a beacon was received,
the DTIM period, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It might be useful to drivers to be able to pass only the
link_conf pointer, rather than both the pointer and the
link_id; add the link_id to the link_conf to facility that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In station/client mode, the link data needs a bit more
initialization and destruction than just zero-init and
kfree() respectively, implement that.
This required some shuffling of the link data handling
in general, as we should set it up in setup and do the
teardown in teardown, otherwise we're asymmetric in
case of interface type changes.
Also stop using kfree_rcu(), we cannot guarantee that
nothing is scheduling things that live within the link
(e.g. the u.mgd.request_smps_work) until we're sure it
cannot be referenced anymore, therefore synchronize
instead. This isn't very efficient, but we can always
optimize it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the split into keys[]/deflink.gtk[] arrays, WEP keys are
still installed into the keys[] array, but we didn't look them
up there. This meant they weren't deleted correctly.
Fix this by looking up the key there even if it's not pairwise
so we can be sure we don't have it.
Fixes: bfd8403add ("wifi: mac80211: reorg some iface data structs for MLD")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Separate out the connection downgrade flags from the ifmgd->flags
and put them into the link information instead. While at it, make
them a separate sparse type so we don't get confused about where
they belong and have static checking on correct handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the mac80211 implementation with P802.11be_D1.5.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places that check ps_sdata and/or the dynamic
PS timeout, but they're erroneous in case SUPPORTS_DYNAMIC_PS
is set by the driver.
Skip the entire recalculation in this case so we cannot get
into those paths elsewhere, and so we simplify this for the
purpose of implementing MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we don't really have multiple links, omit the link ID from
link debug prints, otherwise we change the format for all of
the existing drivers (most of which might never support MLO),
and also have extra noise in the logs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to ieee80211_get_sband but get the sband of the link_conf.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AP SMPS was removed and not needed anymore. Remove the leftovers.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check all the MLO links to decide whether offchannel TX is needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When checking whether or not to accept a frame in RX,
take into account the configured link addresses. Also
look up the link station correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211s_update_metric function uses sta_set_rate_info_tx
function to get struct rate_info data from ieee80211_tx_rate
struct, present in ieee80211_sta->deflink.tx_stats. However,
drivers can skip tx rate calculation by setting rate idx as
-1. Such drivers provides rate_info directly and hence
ieee80211s metric is updated incorrectly since ieee80211_tx_rate
has inconsistent data.
Add fix to use rate_info directly if present instead of
sta_set_rate_info_tx for updating ieee80211s metric.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://lore.kernel.org/r/20220701133611.544-1-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS needs 4addr packets to trigger AP for wlan0.sta creation.
However, the 4addr null frame is sent at a high rate so that
sometimes the AP can't receive it. Switch to using min rate.
Signed-off-by: Lian Chen <lian.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220714091636.59107-1-lian.chen@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, multicast traffic is handled very differently from normal traffic,
especially if at least one client is in powersave mode.
This means that multicast packets can be buffered a lot longer than normal
unicast packets, and can eat up the AQL budget very quickly because of the low
data rate.
Along with the recent change to maintain a global PHY AQL limit, this can lead
to significant latency spikes for unicast traffic.
Since queueing multicast to hardware is currently not constrained by AQL limits
anyway, let's just exclude it from the AQL pending airtime calculation entirely.
Fixes: 8e4bac0671 ("wifi: mac80211: add a per-PHY AQL limit to improve fairness")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220713083444.86129-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using iTXQ, the code assumes that there is only one vif queue for
broadcast packets, using the BE queue. Allowing non-BE queue marking
violates that assumption and txq->ac == skb_queue_mapping is no longer
guaranteed. This can cause issues with queue handling in the driver and
also causes issues with the recent ATF change, resulting in an AQL
underflow warning.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220702145227.39356-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 downgrades working bandwidth, the
center_freq and center_freq1 need to be recalculated.
There is a typo in the case of downgrading bandwidth from
320MHz to 160MHz which would cause a wrong frequency value.
Reviewed-by: Money Wang <Money.Wang@mediatek.com>
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Link: https://lore.kernel.org/r/20220708095823.12959-1-MeiChia.Chiu@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interface isn't (yet) added to the driver, skip the
link info update. This was previously done for the BSS info
changes, but I forgot to copy the same check here.
Fixes: 7b7090b4c6 ("wifi: mac80211: split bss_info_changed method")
Reported-by: syzbot+bce2ca140cc00578ed07@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a client does not generate any local tx activity, accumulating airtime
deficit for the round-robin scheduler can be harmful. If this goes on for too
long, the deficit could grow quite large, which might cause unreasonable
initial latency once the client becomes active
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-7-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that the global pending airtime is more relevant for airtime fairness,
it makes sense to make it accessible via debugfs for debugging
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-6-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to maintain fairness, the amount of queueing needs to be limited
beyond the simple per-station AQL budget, otherwise the driver can simply
repeatedly do scheduling rounds until all queues that have not used their
AQL budget become eligble.
To be conservative, use the high AQL limit for the first txq and add half
of the low AQL for each subsequent queue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows proper deficit accounting to ensure that they don't carry their
deficit until the next time they become active
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When queueing packets for a station, deficit only gets added once the packets
have been transmitted, which could be much later. During that time, a lot of
temporary unfairness could happen, which could lead to bursty behavior.
Fix this by subtracting the aql_tx_pending when checking the deficit in tx
scheduling.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
32 bit is more than enough range for the airtime deficit
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commits 6a789ba679 and
2433647bc8.
The virtual time scheduler code has a number of issues:
- queues slowed down by hardware/firmware powersave handling were not properly
handled.
- on ath10k in push-pull mode, tx queues that the driver tries to pull from
were starved, causing excessive latency
- delay between tx enqueue and reported airtime use were causing excessively
bursty tx behavior
The bursty behavior may also be present on the round-robin scheduler, but there
it is much easier to fix without introducing additional regressions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
struct link_sta_info has now a cur_max_bandwidth data:
net/mac80211/sta_info.h:569: warning: Function parameter or member 'cur_max_bandwidth' not described in 'link_sta_info'
Copy the meaning from struct sta_info, documenting it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/37d898634bb30776442a33833c48cbb21c90ecc6.1656409369.git.mchehab@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a vif is being removed and sdata->bss is cleared, __ieee80211_wake_txqs
can still be called on it, which crashes as soon as sdata->bss is being
dereferenced.
To fix this properly, check for SDATA_STATE_RUNNING before waking queues,
and take the fq lock when setting it (to ensure that __ieee80211_wake_txqs
observes the change when running on a different CPU)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@kernel.org>
Link: https://lore.kernel.org/r/20220531190824.60019-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the capability to specify gfp_t parameter to
ieeee80211_obss_color_collision_notify routine since it runs in
interrupt context in ieee80211_rx_check_bss_color_collision().
Fixes: 6d945a33f2 ("mac80211: introduce BSS color collision detection")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/02c990fb3fbd929c8548a656477d20d6c0427a13.1655419135.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should set the STA deflink addresses in case no
link is really added.
Fixes: 046d2e7c50 ("mac80211: prepare sta handling for MLO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Maintain a hash table of link-sta addresses so we can find
them for management frames etc. where addresses haven't
been replaced by the drivers to the MLD address yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to access these in a race-free way under
traffic while adding/removing them, so RCU-ify the pointers.
This requires passing a link_sta to a lot of functions so
we don't have to do the RCU handling everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hardcoding link[0] is more confusing than using deflink,
so use deflink for now, which requires making the macro
a bit safer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use link and link_conf according to the link_id
provided by cfg in start_ap/stop_ap and change_beacon.
Also use them in the functions called by them.
Note that for a non MLD device, the link_id is 0,
and link[0] and link_conf[0] equal to deflink and
bss_conf respectively (what was there before).
Also, call vif_info_change for BSS related changes (SSID), and
link_info_change for LINK related changes (instead of the
legacy bss_info_change).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a link is added or removed via nl80211, these are
called. Implement them so we don't have to check in all
the different per-link commands whether we've already
created the necessary datastructures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from a station. To do this,
refactor the link alloc/free a bit, splitting that so we
can do it without linking them, to handle failures better.
Note that a station entry must be created representing an
MLD or a non-MLD STA, it cannot change between the two.
When representing an MLD, the 'deflink' is used for the
first link, which might be removed later, in which case
the memory isn't reused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Take a few bits out of the control.flags to add the link ID
to TX frame metadata, so drivers don't need to look it up
by the address themselves. Implement that lookup where it's
needed, for internal frame TX, and set it to "unspecified"
for data transmissions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interface is an MLD, then we don't know which band
the frame will be transmitted on, and we don't know how to
look up the band. Set the band information to zero in that
case, the driver cannot rely on it anyway.
No longer inline ieee80211_tx_skb_tid() since it's even
bigger now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from an interface.
Also add the missing link address to bss_conf (which we
use as link_conf too), and fill it, in station mode for
now just randomly, in AP mode we get the address from
cfg80211 since the link must be created with an address
first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When channel contexts are used, IEEE80211_CONF_CHANGE_SMPS
doesn't make sense and doesn't apply (which is documented).
Mask it in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_build_hdr() we do the same thing for all
interface types except for AP_VLAN, but we can simplify
the code by pulling the common thing in front of the
switch and overriding it for AP_VLAN. This will also
simplify the code for MLD here later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLD, we might eventually not really know the band on status,
but some code assumes it's there. Move the sband lookup deep to
the code that actually needs it, to make it clear where exactly
it's needed and for what purposes.
For rate control, at least initially we won't support it in MLO,
so that won't be an issue.
For TX monitoring, we may have to elide the rate and/or rely on
ieee80211_tx_status_ext() for rate information.
This also simplifies the function prototypes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This used to be sorted by driver methods, APIs and internal
functions, but got added to in the wrong sections. Fix that
by ordering the file properly again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need to setup lists and work structs every time
we switch the interface type, factor that out into a new
ieee80211_link_init() function and use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If MLO is enabled by the driver then validate a set of
capabilities that mac80211 will initially not support
in MLO. This might change if features are implemented.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove MAX_STA_LINKS and use IEEE80211_MLD_MAX_NUM_LINKS
instead to unify between the station and other data structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the code a bit to initialize a link belonging
to a station, and (later) free all allocated links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is unused since commit 52b4810bed ("mac80211: Remove
support for changing AP SMPS mode") so we can just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a few cases we already have the link ID in the APIs,
pass it already even if it cannot be non-zero yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add pointers so we can start using link_id throughout the
code, even if for now only link ID 0 is valid, pointing
to the "built-in" bss_conf, which is used by drivers that
are not aware of MLD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start reorganizing interface related data structures toward
MLD. The most complex part here is for the keys, since we
have to split the various kinds of GTKs off to the link but
still need to use (for WEP) the other keys as a fallback
even for multicast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't really care too much right now since our data
structures are set up to not have a problem with this,
but clearly it's wrong to accept WEP and pairwise keys
with key ID > 3.
However, with MLD we need to split into per-link (GTK,
IGTK, BIGTK) and per interface/MLD (including WEP) keys
so make sure this is not a problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here's a first set of patches for v5.20. This is just a
queue flush, before we get things back from net-next that
are causing conflicts, and then can start merging a lot
of MLO (multi-link operation, part of 802.11be) code.
Lots of cleanups all over.
The only notable change is perhaps wilc1000 being the
first driver to disable WEP (while enabling WPA3).
-----BEGIN PGP SIGNATURE-----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=E0Dx
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for v5.20
Here's a first set of patches for v5.20. This is just a
queue flush, before we get things back from net-next that
are causing conflicts, and then can start merging a lot
of MLO (multi-link operation, part of 802.11be) code.
Lots of cleanups all over.
The only notable change is perhaps wilc1000 being the
first driver to disable WEP (while enabling WPA3).
* tag 'wireless-next-2022-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (29 commits)
wifi: mac80211_hwsim: Directly use ida_alloc()/free()
wifi: mac80211: refactor some key code
wifi: mac80211: remove cipher scheme support
wifi: nl80211: fix typo in comment
wifi: virt_wifi: fix typo in comment
rtw89: add new state to CFO state machine for UL-OFDMA
rtw89: 8852c: add trigger frame counter
ieee80211: add trigger frame definition
wifi: wfx: Remove redundant NULL check before release_firmware() call
wifi: rtw89: support MULTI_BSSID and correct BSSID mask of H2C
wifi: ray_cs: Drop useless status variable in parse_addr()
wifi: ray_cs: Utilize strnlen() in parse_addr()
wifi: rtw88: use %*ph to print small buffer
wifi: wilc1000: add IGTK support
wifi: wilc1000: add WPA3 SAE support
wifi: wilc1000: remove WEP security support
wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down
wifi: rtlwifi: fix error codes in rtl_debugfs_set_write_h2c()
wifi: rtw88: Fix Sparse warning for rtw8821c_hw_spec
wifi: rtw88: Fix Sparse warning for rtw8723d_hw_spec
...
====================
Link: https://lore.kernel.org/r/20220610142838.330862-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's some pretty close code here, with the exception
of RCU dereference vs. protected dereference. Refactor
this to just return a pointer and then do the deref in
the caller later.
Change-Id: Ide5315e2792da6ac66eaf852293306a3ac71ced9
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only driver using this was iwlwifi, where we just removed
the support because it was never really used. Remove the code
from mac80211 as well.
Change-Id: I1667417a5932315ee9d81f5c233c56a354923f09
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_vif_use_reserved_context(), when we have an
old context and the new context's replace_state is set to
IEEE80211_CHANCTX_REPLACE_NONE, we free the old context
in ieee80211_vif_use_reserved_reassign(). Therefore, we
cannot check the old_ctx anymore, so we should set it to
NULL after this point.
However, since the new_ctx replace state is clearly not
IEEE80211_CHANCTX_REPLACES_OTHER, we're not going to do
anything else in this function and can just return to
avoid accessing the freed old_ctx.
Cc: stable@vger.kernel.org
Fixes: 5bcae31d9c ("mac80211: implement multi-vif in-place reservations")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220601091926.df419d91b165.I17a9b3894ff0b8323ce2afdb153b101124c821e5@changeid
Second set of patches for v5.19 and most likely the last one. rtw89
got support for 8852ce devices and mt76 now supports Wireless Ethernet
Dispatch.
Major changes:
cfg80211/mac80211
* support disabling EHT mode
rtw89
* add support for Realtek 8852ce devices
mt76
* Wireless Ethernet Dispatch support for flow offload
* non-standard VHT MCS10-11 support
* mt7921 AP mode support
* mt7921 ipv6 NS offload support
ath11k
* enable keepalive during WoWLAN suspend
* implement remain-on-channel support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmKGYt4RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuK2gf/ZswLtwE2CIwrEhz/Q0MDtxUvw8ulRhKl
d+1PC+bCd/VArMESjpu7le+WNAZ1OPBWdh1pgkDm8QpCQZYe7/hRED82DB/Jw3Cl
KmOx2nr6Xb4uEN+yjqZrSXzA+Hrysy24bCQRG2CJKjdToe/fwTuRiz8WIcPKtxio
b/d/Kz0LpSoHTlU1PzqIsXulN8QUKJA4kRw70rJHAlMJVYiTBuAD+AmXfbhHD8uX
t2CJDH2fykDd1CAWFQwcmI++2tS+xclYL81vDg3aEinQJ9aNcDz06qSE5qr2H+K5
lUYy42yc+ONkIIh8LlxrLgZie7oSmkrb7aA0Zc+F0SWp/B6ZO/k8FA==
=aILH
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
Second set of patches for v5.19 and most likely the last one. rtw89
got support for 8852ce devices and mt76 now supports Wireless Ethernet
Dispatch.
Major changes:
cfg80211/mac80211
- support disabling EHT mode
rtw89
- add support for Realtek 8852ce devices
mt76
- Wireless Ethernet Dispatch support for flow offload
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 ipv6 NS offload support
ath11k
- enable keepalive during WoWLAN suspend
- implement remain-on-channel support
* tag 'wireless-next-2022-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (135 commits)
iwlwifi: mei: fix potential NULL-ptr deref
iwlwifi: mei: clear the sap data header before sending
iwlwifi: mvm: remove vif_count
iwlwifi: mvm: always tell the firmware to accept MCAST frames in BSS
iwlwifi: mvm: add OTP info in case of init failure
iwlwifi: mvm: fix assert 1F04 upon reconfig
iwlwifi: fw: init SAR GEO table only if data is present
iwlwifi: mvm: clean up authorized condition
iwlwifi: mvm: use NULL instead of ERR_PTR when parsing wowlan status
iwlwifi: pcie: simplify MSI-X cause mapping
rtw89: pci: only mask out INT indicator register for disable interrupt v1
rtw89: convert rtw89_band to nl80211_band precisely
rtw89: 8852c: update txpwr tables to HALRF_027_00_052
rtw89: cfo: check mac_id to avoid out-of-bounds
rtw89: 8852c: set TX antenna path
rtw89: add ieee80211::sta_rc_update ops
wireless: Fix Makefile to be in alphabetical order
mac80211: refactor freeing the next_beacon
cfg80211: fix kernel-doc for cfg80211_beacon_data
mac80211: minstrel_ht: support ieee80211_rate_status
...
====================
Link: https://lore.kernel.org/r/20220519153334.8D051C385AA@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for the new struct ieee80211_rate_status and its
annotation in struct ieee80211_tx_status in minstrel_ht.
In minstrel_ht_tx_status, a check for the presence of instances of the
new struct in ieee80211_tx_status is added. Based on this, minstrel_ht
then gets and updates internal rate stats with either struct
ieee80211_rate_status or ieee80211_tx_info->status.rates.
Adjusted variants of minstrel_ht_txstat_valid, minstrel_ht_get_stats,
minstrel_{ht/vht}_get_group_idx are added which use struct
ieee80211_rate_status and struct rate_info instead of the legacy structs.
struct rate_info from cfg80211.h does not provide whether short preamble
was used for the transmission. So we retrieve this information from VIF
and STA configuration and cache it in a new flag in struct minstrel_ht_sta
per rate control instance.
Compile-Tested: current wireless-next tree with all flags on
Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt
Linux 5.10.113
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://lore.kernel.org/r/20220509173958.1398201-3-jelonek.jonas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the new struct ieee80211_rate_status and replaces
'struct rate_info *rate' in ieee80211_tx_status with pointer and length
annotation.
The struct ieee80211_rate_status allows to:
(1) receive tx power status feedback for transmit power control (TPC)
per packet or packet retry
(2) dynamic mapping of wifi chip specific multi-rate retry (mrr)
chains with different lengths
(3) increase the limit of annotatable rate indices to support
IEEE802.11ac rate sets and beyond
ieee80211_tx_info, control and status buffer, and ieee80211_tx_rate
cannot be used to achieve these goals due to fixed size limitations.
Our new struct contains a struct rate_info to annotate the rate that was
used, retry count of the rate and tx power. It is intended for all
information related to RC and TPC that needs to be passed from driver to
mac80211 and its RC/TPC algorithms like Minstrel_HT. It corresponds to
one stage in an mrr. Multiple subsequent instances of this struct can be
included in struct ieee80211_tx_status via a pointer and a length variable.
Those instances can be allocated on-stack. The former reference to a single
instance of struct rate_info is replaced with our new annotation.
An extension is introduced to struct ieee80211_hw. There are two new
members called 'tx_power_levels' and 'max_txpwr_levels_idx' acting as a
tx power level table. When a wifi device is registered, the driver shall
supply all supported power levels in this list. This allows to support
several quirks like differing power steps in power level ranges or
alike. TPC can use this for algorithm and thus be designed more abstract
instead of handling all possible step widths individually.
Further mandatory changes in status.c, mt76 and ath11k drivers due to the
removal of 'struct rate_info *rate' are also included.
status.c already uses the information in ieee80211_tx_status->rate in
radiotap, this is now changed to use ieee80211_rate_status->rate_idx.
mt76 driver already uses struct rate_info to pass the tx rate to status
path. The new members of the ieee80211_tx_status are set to NULL and 0
because the previously passed rate is not relevant to rate control and
accurate information is passed via tx_info->status.rates.
For ath11k, the txrate can be passed via this struct because ath11k uses
firmware RC and thus the information does not interfere with software RC.
Compile-Tested: current wireless-next tree with all flags on
Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt
Linux 5.10.113
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://lore.kernel.org/r/20220509173958.1398201-2-jelonek.jonas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fill all requested rates (in case of ath9k 4 rate slots are
available, so fill all 4 instead of only 3), improves throughput in
noisy environment.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Link: https://lore.kernel.org/r/20220402153014.31332-2-ps.report@gmx.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AP may run out of BSS color after color collision
detection event from driver.
Disable BSS color collision detection if no free colors are
available based on bss color disabled bit sent as a part of
NL80211_ATTR_HE_BSS_COLOR attribute sent in
NL80211_CMD_SET_BEACON.
It can be reenabled once new color is available.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-3-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_HE_BSS_COLOR attribute can be included in both
NL80211_CMD_START_AP and NL80211_CMD_SET_BEACON commands.
Move he_bss_color from cfg80211_ap_settings to cfg80211_beacon_data
and parse NL80211_ATTR_HE_BSS_COLOR as a part of nl80211_parse_beacon()
to have bss color settings parsed for both start ap and set beacon
commands.
Add a new flag he_bss_color_valid to indicate whether
NL80211_ATTR_HE_BSS_COLOR attribute is included.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-2-git-send-email-quic_ramess@quicinc.com
[fix build ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently track whether we're associated and which the
BSS is in the same variable (ifmgd->associated), but for
MLD we'll need to move the BSS pointer to be per link,
while the question whether we're associated or not is for
the whole interface.
Add ifmgd->assoc_bss that stores the pointer and change
ifmgd->associated to be just a bool, so the question of
whether we're associated can continue working after MLD
rework, without requiring changes, while the BSS pointer
will have to be changed/used checked per link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need to copy this locally, we now only use the
variable to print before doing other things.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We never use the bssid argument to ieee80211_sta_connection_lost()
so we might as well just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to look it up from the ifmgd->associated
BSS configuration, we already maintain a local copy since
commit b0140fda62 ("mac80211: mlme: save ssid info to
ieee80211_bss_conf while assoc").
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we always track the BSSID there when we get associated,
these are equivalent, but ifmgd->bssid saves a dereference and
thus makes the code a bit smaller, and more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is tightly coupled to the sdata->u.mgd data
structure, so there's no reason for it to be in utils.
Move it to mlme.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ping-Ke's previous patch adjusted the CCMP AAD construction
to properly take the order bit into account, but failed to
update the (identical) GCMP AAD construction as well.
Unify the AAD construction between the two cases.
Reported-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20220506105150.51d66e2a6f3c.I65f12be82c112365169e8a9f48c7a71300e814b9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In client mode, we can't connect to hidden SSID APs or SSIDs not advertised
in beacons on DFS channels, since we're forced to passive scan. Fix this by
sending out a probe request immediately after the first beacon, if active
scan was requested by the user.
Cc: stable@vger.kernel.org
Reported-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220420104907.36275-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If statement is meaningless because the code will goto out regardless of
whether fast_tx is NULL or not.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220413091902.27438-1-hbh25y@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Follow IEEE 802.11-21 that HTC subfield masked to 0 for all data frames
containing a QoS Control field. It also defines the AAD length depends on
QC and A4 fields, so change logic to determine length accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220324004816.6202-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently MBSSID parameters in struct ieee80211_bss_conf
are not reset upon connection. This could be problematic
with some drivers in a scenario where the device first
connects to a non-transmit BSS and then connects to a
transmit BSS of a Multi BSS AP. The MBSSID parameters
which are set after connecting to a non-transmit BSS will
not be reset and the same parameters will be passed on to
the driver during the subsequent connection to a transmit
BSS of a Multi BSS AP.
For example, firmware running on the ath11k device uses the
Multi BSS data for tracking the beacon of a non-transmit BSS
and reports the driver when there is a beacon miss. If we do
not reset the MBSSID parameters during the subsequent
connection to a transmit BSS, then the driver would have
wrong MBSSID data and FW would be looking for an incorrect
BSSID in the MBSSID beacon of a Multi BSS AP and reports
beacon loss leading to an unstable connection.
Reset the MBSSID parameters upon every connection to solve this
problem.
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Link: https://lore.kernel.org/r/20220428052744.27040-1-quic_mpubbise@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the QoS ack policy was set to non explicit / psmp ack, frames are treated
as not being part of a BA session, which causes extra latency on reordering.
Fix this by only bypassing reordering for packets with no-ack policy
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220420105038.36443-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
* wfx: silicon labs devices
* plfxlc: pureLiFi X, XL, XC devices
mac80211
* host based BSS color collision detection
* prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
* support TP-Link T2E devices
rtw89
* support firmware crash simulation
* preparation for 8852ce hardware support
ath11k
* Wake-on-WLAN support for QCA6390 and WCN6855
* device recovery (firmware restart) support for QCA6390 and WCN6855
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
wcn36xx
* support for transmit rate reporting to user space
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmJxS2sRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuNgwf9H2oxMKLKrlFoX1qHtNBwZuHS6IERhOkM
NI9DjS4MCyiUSbA5r3sWlpqXQeKIbG/05gUZ6Y0ircGFwnAGjZ6isPwo8pKFgbh5
QljXQjUTHbkshrXW8K+VGJxw4F1oiPlOGUDVdXPy2FLx5ZvBlaUV2rWQUzsWX9I0
EnrM6ygHBVejVYDe+JSkb1gzb/07xuZN410IJPuZTPKJfYiE0oGU3zpTbExFitaz
ObjfFUWqHrVue525WFAJ9Dbk8kYEKyMThr7rkkWekYJjujJLJo0qhEiZVZu0eEsk
Vq4PdKmQAqlgbShQ/3Mv8BRsSH2wy62+zKjPWL+8t4Gmm9DbLu+++A==
=T7Ii
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
- wfx: silicon labs devices
- plfxlc: pureLiFi X, XL, XC devices
mac80211
- host based BSS color collision detection
- prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
- support TP-Link T2E devices
rtw89
- support firmware crash simulation
- preparation for 8852ce hardware support
ath11k
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support for QCA6390 and WCN6855
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- support for WCN6750
wcn36xx
- support for transmit rate reporting to user space
* tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits)
rtw89: 8852c: rfk: add DPK
rtw89: 8852c: rfk: add IQK
rtw89: 8852c: rfk: add RX DCK
rtw89: 8852c: rfk: add RCK
rtw89: 8852c: rfk: add TSSI
rtw89: 8852c: rfk: add LCK
rtw89: 8852c: rfk: add DACK
rtw89: 8852c: rfk: add RFK tables
plfxlc: fix le16_to_cpu warning for beacon_interval
rtw88: remove a copy of the NAPI_POLL_WEIGHT define
carl9170: tx: fix an incorrect use of list iterator
wil6210: use NAPI_POLL_WEIGHT for napi budget
ath10k: remove a copy of the NAPI_POLL_WEIGHT define
ath11k: Add support for WCN6750 device
ath11k: Datapath changes to support WCN6750
ath11k: HAL changes to support WCN6750
ath11k: Add QMI changes for WCN6750
ath11k: Fetch device information via QMI for WCN6750
ath11k: Add register access logic for WCN6750
ath11k: Add HW params for WCN6750
...
====================
Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if it is not a real issue since ieee80211_set_after_csa_beacon()
or ieee80211_set_after_color_change_beacon() are run only when csa or bcc
is active, move next_beacon check before running ieee80211_assign_beacon
routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/041764ed7e9781bcee66c33b41f1365aa4205932.1649327683.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't use sizeof(pointer) when calculating scnprintf offset.
Fixes: 01f84f0ed3 ("mac80211: reduce stack usage in debugfs")
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20220406175659.20611-1-greearb@candelatech.com
[correct the Fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Trigger ieee80211_csa_finish() on the non-transmitting interfaces
when channel switch concludes on the transmitting interface.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/6fde4d7f9fa387494f46a7aa4a584478dcda06f1.1645702516.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new fields in struct beacon_data to store all MBSSID elements.
Generate a beacon template which includes all MBSSID elements.
Move CSA offset to reflect the MBSSID element length.
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Money Wang <money.wang@mediatek.com>
Link: https://lore.kernel.org/r/5322db3c303f431adaf191ab31c45e151dde5465.1645702516.git.lorenzo@kernel.org
[small cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
-----BEGIN PGP SIGNATURE-----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=ccps
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While commit 6a01afcf84 ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:
ieee80211_leave_mesh()
-> kfree(sdata->u.mesh.ie);
...
ieee80211_join_mesh()
-> copy_mesh_setup()
-> old_ie = ifmsh->ie;
-> kfree(old_ie);
This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:
$ iw dev mesh0 mesh leave
$ iw dev mesh0 mesh join my-mesh
Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.
The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.
Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.
Cc: stable@vger.kernel.org
Fixes: 6a01afcf84 ("mac80211: mesh: Free ie data when leaving mesh")
Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no legacy rates on 60GHz or sub-1GHz band, so modify the check.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Link: https://lore.kernel.org/r/20220308021645.16272-1-MeiChia.Chiu@mediatek.com
[Ghz -> GHz]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous memory allocations in this function already use GFP_KERNEL, so
use __dev_alloc_skb() and an explicit GFP_KERNEL instead of an implicit
GFP_ATOMIC.
This gives more opportunities of successful allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/194a0e2ff00c3fae88cc9fba47431747360c8242.1645345378.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we get anti-clogging token required (added by the commit
mentioned below), or the other status codes added by the later
commit 4e56cde15f ("mac80211: Handle special status codes in
SAE commit") we currently just pretend (towards the internal
state machine of authentication) that we didn't receive anything.
This has the undesirable consequence of retransmitting the prior
frame, which is not expected, because the timer is still armed.
If we just disarm the timer at that point, it would result in
the undesirable side effect of being in this state indefinitely
if userspace crashes, or so.
So to fix this, reset the timer and set a new auth_data->waiting
in order to have no more retransmissions, but to have the data
destroyed when the timer actually fires, which will only happen
if userspace didn't continue (i.e. crashed or abandoned it.)
Fixes: a4055e74a2 ("mac80211: Don't destroy auth data in case of anti-clogging")
Reported-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20220224103932.75964e1d7932.Ia487f91556f29daae734bf61f8181404642e1eec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In EHT requesting aggregation with 1K needs the use of extended
the AddBA element for the buffer size, so add the logic to parse
it and make sure it's in limits of the EHT aggregation size.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.8209cae9d9e4.I434f5588602f83b4e658c660120040913b3a2e3d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We add the fields for parsing extended ADDBA request/respond,
and new max 1K aggregation for limit ADDBA request/respond.
Adjust drivers to use the proper macro, IEEE80211_MAX_AMPDU_BUF ->
IEEE80211_MAX_AMPDU_BUF_HE.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.b8b447ce95b7.I0ee2554c94e89abc7a752b0f7cc7fd79c273efea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two problems with the current code that have been highlighted
with the AQL feature that is now enbaled by default.
First problem is in ieee80211_rx_h_mesh_fwding(),
ieee80211_select_queue_80211() is used on received packets to choose
the sending AC queue of the forwarding packet although this function
should only be called on TX packet (it uses ieee80211_tx_info).
This ends with forwarded mesh packets been sent on unrelated random AC
queue. To fix that, AC queue can directly be infered from skb->priority
which has been extracted from QOS info (see ieee80211_parse_qos()).
Second problem is the value of queue_mapping set on forwarded mesh
frames via skb_set_queue_mapping() is not the AC of the packet but a
hardware queue index. This may or may not work depending on AC to HW
queue mapping which is driver specific.
Both of these issues lead to improper AC selection while forwarding
mesh packets but more importantly due to improper airtime accounting
(which is done on a per STA, per AC basis) caused traffic stall with
the introduction of AQL.
Fixes: cf44012810 ("mac80211: fix unnecessary frame drops in mesh fwding")
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Co-developed-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://lore.kernel.org/r/20220214173214.368862-1-nico.escande@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an MFP station isn't authorized, the receiver will (or
at least should) drop the action frame since it's a robust
management frame, but if we're not authorized we haven't
installed keys yet. Refuse attempts to start a session as
they'd just time out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20220203201528.ff4d5679dce9.I34bb1f2bc341e161af2d6faf74f91b332ba11285@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 set capability NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211
to upper layer by default. That means we should pass EAPoL packets through
nl80211 path only, and should not send the EAPoL skb to netdevice diretly.
At the meanwhile, wpa_supplicant would not register sock to listen EAPoL
skb on the netdevice.
However, there is no control_port_protocol handler in mac80211 for 802.3 RX
packets, mac80211 driver would pass up the EAPoL rekey frame to netdevice
and wpa_supplicant would be never interactive with this kind of packets,
if SUPPORTS_RX_DECAP_OFFLOAD is enabled. This causes STA always rekey fail
if EAPoL frame go through 802.3 path.
To avoid this problem, align the same process as 802.11 type to handle
this frame before put it into network stack.
This also addresses a potential security issue in 802.3 RX mode that was
previously fixed in commit a8c4d76a8d ("mac80211: do not accept/forward
invalid EAPOL frames").
Cc: stable@vger.kernel.org # 5.12+
Fixes: 80a915ec44 ("mac80211: add rx decapsulation offload support")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://lore.kernel.org/r/6889c9fced5859ebb088564035f84fd0fa792a49.1644680751.git.deren.wu@mediatek.com
[fix typos, update comment and add note about security issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following coccicheck warnings:
net/mac80211/util.c:3265:3: warning: Value stored to 'channel_type' is
never read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220113161557.129427-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We check ieee80211_vif_is_mesh() at the top if() block,
there's no need to check for it again.
Signed-off-by: Baligh Gasmi <gasmibal@gmail.com>
Link: https://lore.kernel.org/r/20220203153035.198697-1-gasmibal@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The size of the status_driver_data field was not adjusted when
the is_valid_ack_signal field was added.
Since the size of struct ieee80211_tx_info is limited, replace
the is_valid_ack_signal field with a flags field, and adjust the
struct size accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.0ff363d4fa56.I45792c0187034a6d0e1c99a7db741996ef7caba3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We validate that AP has mandatory rates set in HE capabilities.
Also we make sure AP is consistent with itself on rates set in HE basic
rates required joining the BSS and rates set in HE capabilities.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.7023450fdf16.I194df59252097ba25a0a543456d4350f1607a538@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE80211_VHT_MCS_NOT_SUPPORTED and IEEE80211_HE_MCS_NOT_SUPPORTED
have the same value so no real bug, but for code integrity use the
HE macros for parsing HE capabilities.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.e974b7b3b217.I732cc7f770c7fa06e4840adb5d45d7ee99ac8eb5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's currently only one driver that reports CHECKSUM_COMPLETE,
that is iwlwifi. The current hardware there calculates checksum
after the SNAP header, but only RFC 1042 (and some other cases,
but replicating the exact hardware logic for corner cases in the
driver seemed awkward.)
Newer generations of hardware will checksum _including_ the SNAP,
which makes things easier.
To handle that, simply always assume the checksum _includes_ the
SNAP header, which this patch does, requiring to first add it
for older iwlwifi hardware, and then remove it again later on
conversion.
Alternatively, we could have:
1) Always assumed the checksum starts _after_ the SNAP header;
the problem with this is that we'd have to replace the exact
"what is the SNAP" check in iwlwifi that cfg80211 has.
2) Made it configurable with some flag, but that seemed like too
much complexity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.230736e19e0e.I3e6745873585ad943c152fab9e23b5221f17a95f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In UHB connection we don't have any HT/VHT elemens so in order to
calculate the max RX-NSS we need also to look at HE capa element, this
causes to limit us to max rx nss in UHB to 1.
Also anyway we need to look at HE max rx NSS and not only at HT/VHT
capa to determine the max rx nss over the connection.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.3713e0dea5dd.I3b9a15b4c53465c3f86f35459e9dc15ae4ea2abd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we're limiting bandwidth for some reason such as regulatory
restrictions, then advertise that limitation just like we do
for VHT today, so the AP is aware we cannot use the higher BW
it might be using.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.70c8e3e7ee76.If317630de69ff1146bec7d47f5b83038695eb71d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the possible failure of the alloc, the ifmgd->assoc_req_ies might be
NULL pointer returned from kmemdup().
Therefore it might be better to free the skb and return error in order
to fail the association, like ieee80211_assoc_success().
Also, the caller, ieee80211_do_assoc(), needs to deal with the return
value from ieee80211_send_assoc().
Fixes: 4d9ec73d2b ("cfg80211: Report Association Request frame IEs in association events")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220105081559.2387083-1-jiasheng@iscas.ac.cn
[fix some paths to be errors, not success]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_iterate_active_interfaces() and
ieee80211_iterate_active_interfaces_atomic() already exist, where the
former allows the iterator function to sleep. Add
ieee80211_iterate_stations() which is similar to
ieee80211_iterate_stations_atomic() but allows the iterator to sleep.
This is needed for adding SDIO support to the rtw88 driver. Some
interators there are reading or writing registers. With the SDIO ops
(sdio_readb, sdio_writeb and friends) this means that the iterator
function may sleep.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211228211501.468981-2-martin.blumenstingl@googlemail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit c27aa56a72 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192891
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220103013623.17052-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Syzbot hit NULL deref in rhashtable_free_and_destroy(). The problem was
in mesh_paths and mpp_paths being NULL.
mesh_pathtbl_init() could fail in case of memory allocation failure, but
nobody cared, since ieee80211_mesh_init_sdata() returns void. It led to
leaving 2 pointers as NULL. Syzbot has found null deref on exit path,
but it could happen anywhere else, because code assumes these pointers are
valid.
Since all ieee80211_*_setup_sdata functions are void and do not fail,
let's embedd mesh_paths and mpp_paths into parent struct to avoid
adding error handling on higher levels and follow the pattern of others
setup_sdata functions
Fixes: 60854fd945 ("mac80211: mesh: convert path table to rhashtable")
Reported-and-tested-by: syzbot+860268315ba86ea6b96b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20211230195547.23977-1-paskripkin@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clang static analysis reports this warnings
mlme.c:5332:7: warning: Branch condition evaluates to a
garbage value
have_higher_than_11mbit)
^~~~~~~~~~~~~~~~~~~~~~~
have_higher_than_11mbit is only set to true some of the time in
ieee80211_get_rates() but is checked all of the time. So
have_higher_than_11mbit needs to be initialized to false.
Fixes: 5d6a1b069b ("mac80211: set basic rates earlier")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211223162848.3243702-1-trix@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ETSI standard defines "Offchannel CAC" as:
"Off-Channel CAC is performed by a number of non-continuous checks
spread over a period in time. This period, which is required to
determine the presence of radar signals, is defined as the Off-Channel
CAC Time..
Minimum Off-Channel CAC Time 6 minutes and Maximum Off-Channel CAC Time
4 hours..".
mac80211 implementation refers to a dedicated hw chain used for continuous
radar monitoring. Rename offchannel_* references to background_* in
order to avoid confusion with ETSI standard.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/4204cc1d648d76b44557981713231e030a3bd991.1638190762.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce a disconnect function that can be used when a
channel switch error occurs. The channel switch can request to
block the tx, and so, we need to make sure we do not send a deauth
frame in this case.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cd2a615a0702.I9edb14785586344af17644b610ab5be109dcef00@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In mac80211, while building radiotap header
IEEE80211_RADIOTAP_MCS_HAVE_FEC flag is missing when LDPC enabled
from driver, hence LDPC is not updated properly in radiotap header.
Fix that by adding HAVE_FEC flag while building radiotap header.
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://lore.kernel.org/r/1638294648-844-2-git-send-email-quic_ppranees@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time values used by the airtime fairness code only need to be accurate
enough to cover station activity detection.
Using ktime_get_coarse_boottime_ns instead of ktime_get_boottime_ns will
drop the accuracy down to jiffies intervals, but at the same time saves
a lot of CPU cycles in a hot path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20211217114258.14619-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we reconfigure, the driver might do some things to complete
the reconfiguration. It's strange and could be broken in some
cases because we restart other works (e.g. remain-on-channel and
TX) before this happens, yet only start queues later.
Change this to do the reconfig complete when reconfiguration is
actually complete, not when we've already started doing other
things again.
For iwlwifi, this should fix a race where the reconfig can race
with TX, for ath10k and ath11k that also use this it won't make
a difference because they just start queues there, and mac80211
also stopped the queues and will restart them later as before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cab99f22fe19.Iefe494687f15fd85f77c1b989d1149c8efdfdc36@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mark TXQs as having seen transmit while they were stopped if
we bail out of drv_wake_tx_queue() due to reconfig, so that
the queue wake after this will make them catch up. This is
particularly necessary for when TXQs are used for management
packets since those TXQs won't see a lot of traffic that'd
make them catch up later.
Cc: stable@vger.kernel.org
Fixes: 4856bfd230 ("mac80211: do not call driver wake_tx_queue op during reconfig")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.4573a221c0e1.I0d1d5daea3089be3fc0dccc92991b0f8c5677f0c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently channel context is updated only after station got an update about
new assoc state, this results in station using the old channel context.
Fix this by moving the update channel context before updating station,
enabling the driver to immediately use the updated channel context in
the new assoc state.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.1c80c17ffd8a.I94ae31378b363c1182cfdca46c4b7e7165cff984@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should be doing the HE capabilities lookup based on the full
interface type so if P2P doesn't have HE but client has it doesn't
get confused. Fix that.
Fixes: 2ab4587675 ("mac80211: add support for the ADDBA extension element")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.010fc1d61137.If3a468145f29d670cb00a693bed559d8290ba693@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we call ieee80211_agg_start_txq(), that will in turn call
schedule_and_wake_txq(). Called from ieee80211_stop_tx_ba_cb()
this is done under sta->lock, which leads to certain circular
lock dependencies, as reported by Chris Murphy:
https://lore.kernel.org/r/CAJCQCtSXJ5qA4bqSPY=oLRMbv-irihVvP7A2uGutEbXQVkoNaw@mail.gmail.com
In general, ieee80211_agg_start_txq() is usually not called
with sta->lock held, only in this one place. But it's always
called with sta->ampdu_mlme.mtx held, and that's therefore
clearly sufficient.
Change ieee80211_stop_tx_ba_cb() to also call it without the
sta->lock held, by factoring it out of ieee80211_remove_tid_tx()
(which is only called in this one place).
This breaks the locking chain and makes it less likely that
we'll have similar locking chain problems in the future.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211202152554.f519884c8784.I555fef8e67d93fff3d9a304886c4a9f8b322e591@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's easier to use and understand, and to extend for EHT later,
if we use the values here instead of the shifted values.
Unfortunately, we need to add _POS so that we can use it in
places like iwlwifi/mvm where constants are needed.
While at it, fix the typo ("NOMIMAL") which also helps catch any
conflicts.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/r/20211126104817.7c29a05b8eb5.I2ca9faf06e177e3035bec91e2ae53c2f91d41774@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When color change is triggered in multiple bssid case, allow
only for transmitting BSS, and when it changes its bss color,
notify the non transmitting BSSs also of the new bss color.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1637146647-16282-1-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to provide a destination device + info for flow offload
Only supported in combination with 802.3 encap offload
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20211112112223.1209-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The assignment of these three local variables in the file will not
be used in the corresponding functions, so they should be deleted.
The clang_analyzer complains as follows:
net/mac80211/wpa.c:689:2 warning:
net/mac80211/wpa.c:883:2 warning:
net/mac80211/wpa.c:452:2 warning:
Value stored to 'hdr' is never read
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Link: https://lore.kernel.org/r/20211104061411.1744-1-luo.penghao@zte.com.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following is from a system that went OOM due to a memory leak:
wlan0: Allocated STA 74:83:c2:64:0b:87
wlan0: Allocated STA 74:83:c2:64:0b:87
wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_add_sta)
wlan0: Adding new IBSS station 74:83:c2:64:0b:87
wlan0: moving STA 74:83:c2:64:0b:87 to state 2
wlan0: moving STA 74:83:c2:64:0b:87 to state 3
wlan0: Inserted STA 74:83:c2:64:0b:87
wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_work)
wlan0: Adding new IBSS station 74:83:c2:64:0b:87
wlan0: moving STA 74:83:c2:64:0b:87 to state 2
wlan0: moving STA 74:83:c2:64:0b:87 to state 3
.
.
wlan0: expiring inactive not authorized STA 74:83:c2:64:0b:87
wlan0: moving STA 74:83:c2:64:0b:87 to state 2
wlan0: moving STA 74:83:c2:64:0b:87 to state 1
wlan0: Removed STA 74:83:c2:64:0b:87
wlan0: Destroyed STA 74:83:c2:64:0b:87
The ieee80211_ibss_finish_sta() is called twice on the same STA from 2
different locations. On the second attempt, the allocated STA is not
destroyed creating a kernel memory leak.
This is happening because sta_info_insert_finish() does not call
sta_info_free() the second time when the STA already exists (returns
-EEXIST). Note that the caller sta_info_insert_rcu() assumes STA is
destroyed upon errors.
Same fix is applied to -ENOMEM.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20211002145329.3125293-1-anzaki@gmail.com
[change the error path label to use the existing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers that do their own sequence number allocation (e.g. ath9k) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Cc: stable@vger.kernel.org
Fixes: 31d8bb4e07 ("mac80211: agg-tx: refactor sending addba")
Reported-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211124094024.43222-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since retransmission clears info->control, rate control needs to be called
again, otherwise the driver might crash due to invalid rates.
Cc: stable@vger.kernel.org # 5.14+
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Robert W <rwbugreport@lost-in-the-void.net>
Fixes: 03c3911d2d ("mac80211: call ieee80211_tx_h_rate_ctrl() when dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20211122204323.9787-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to cfg80211, introduce set_radar_offchan callback in mac80211_ops
in order to configure a dedicated offchannel chain available on some hw
(e.g. mt7915) to perform offchannel CAC detection and avoid tx/rx downtime.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/201110606d4f3a7dfdf31440e351f2e2c375d4f0.1634979655.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The codepaths for rx with decap offload and tx with itxq were not updating
the counters for the throughput led trigger.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211113063415.55147-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit a05829a722 ("cfg80211: avoid holding the RTNL when
calling the driver") we've not only been protecting the pointer
to monitor_sdata with the RTNL, but also with the wiphy->mtx. This
is relevant in a number of lockdep assertions, e.g. the one we hit
in ieee80211_set_monitor_channel(). However, we're now protecting
all the assignments/dereferences, even the one in interface iter,
with the wiphy->mtx, so switch over the lockdep assertions to that
lock.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20211112135143.cb8e8ceffef3.Iaa210f16f6904c8a7a24954fb3396da0ef86ec08@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When __ieee80211_select_queue is called, skb->cb has not been cleared yet,
which means that info->control.flags can contain garbage.
In some cases this leads to IEEE80211_TX_CTRL_DONT_REORDER being set, causing
packets marked for other queues to randomly end up in BE instead.
This flag only needs to be checked in ieee80211_select_queue_80211, since
the radiotap parser is the only piece of code that sets it
Fixes: 66d06c8473 ("mac80211: adhere to Tx control flag that prevents frame reordering")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211110212201.35452-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 8c89f7b3d3 ("mac80211: Use flex-array for radiotap header
bitmap") we accidentally pointed the position to the wrong place, so
we overwrite a present bitmap, and thus cause all kinds of trouble.
To see the issue, note that the previous code read:
pos = (void *)(it_present + 1);
The requirement now is that we need to calculate pos via it_optional,
to not trigger the compiler hardening checks, as:
pos = (void *)&rthdr->it_optional[...];
Rewriting the original expression, we get (obviously, since that just
adds "+ x - x" terms):
pos = (void *)(it_present + 1 + rthdr->it_optional - rthdr->it_optional)
and moving the "+ rthdr->it_optional" outside to be used as an array:
pos = (void *)&rthdr->it_optional[it_present + 1 - rthdr->it_optional];
The original is off by one, fix it.
Cc: stable@vger.kernel.org
Fixes: 8c89f7b3d3 ("mac80211: Use flex-array for radiotap header bitmap")
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sid Hayn <sidhayn@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211109100203.c61007433ed6.I1dade57aba7de9c4f48d68249adbae62636fd98c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_get_keyid() will return false value if IV has been stripped,
such as return 0 for IP/ARP frames due to LLC header, and return -EINVAL
for disassociation frames due to its length... etc. Don't try to access
it if it's not present.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Link: https://lore.kernel.org/r/20211101024657.143026-1-xing.song@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
-----BEGIN PGP SIGNATURE-----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=ZXrI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Quite a few changes:
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
* tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
cfg80211: fix kernel-doc for MBSSID EMA
mac80211: Prevent AP probing during suspend
nl80211: Add LC placeholder band definition to nl80211_band
...
====================
Link: https://lore.kernel.org/r/20211021154953.134849-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Submitting AP probe/null during suspend can cause unexpected
disconnect on resume because of timeout waiting for ack status:
wlan0: Failed to send nullfunc to AP 11:22:33:44:55:66 after 500ms, disconnecting
This is especially the case when we enter suspend when a scan is
ongoing, indeed, scan is cancelled from __ieee80211_suspend, leading
to a corresponding (aborted) scan complete event, which in turn causes
the submission of an immediate monitor null frame (restart_sta_timer).
The corresponding packet or ack will not be processed before resuming,
causing a timeout & disconnect on resume.
Delay the AP probing when suspending/suspended.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1634805927-1113-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define LC band which is a draft under IEEE 802.11bb.
Current NL80211_BAND_LC is a placeholder band and
will be more defined IEEE 802.11bb progresses.
Signed-off-by: Srinivasan Raju <srini.raju@purelifi.com>
Link: https://lore.kernel.org/r/20211018100143.7565-2-srini.raju@purelifi.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split __ieee80211_beacon_get() into a separate function for AP mode
ieee80211_beacon_get_ap().
Also, move the code common to all modes (AP, adhoc and mesh) to
a separate function ieee80211_beacon_get_finish().
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20211006040938.9531-2-alokad@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
