The TUSB320 can detect the following types of accessory:
- Audio Accessory
- Audio Accessory with charge-thru
- Debug Accessory (DFP)
- Debug Accessory (UFP)
Moreover, the typec subsystem can be informed of this through the
typec_set_mode() function. The information will be propagated to any
linked typec muxes. Add the necessary support to the driver.
Note that for the Debug Accessory modes, an educated guess was made that
for the USB data role, DFP implies HOST and UFP implies DEVICE. But this
might want to be made configurable at a later date.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The alloc groups is functionalized from extcon_dev_register.
Signed-off-by: Bumwoo Lee <bw365.lee@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The mutual exclusive part is functionalized from extcon_dev_register.
Signed-off-by: Bumwoo Lee <bw365.lee@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The cable allocation part is functionalized from extcon_dev_register.
Signed-off-by: Bumwoo Lee <bw365.lee@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
of_gpio.h provides a single function, which is not used in this driver.
Remove unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Valid configurations for the extcon interrupt declarations are
- usb_id
- usb_vbus
- (usb_id | usb_vbus)
In the case of a standalone usb_id or usb_vbus failure to find one of the
interrupts shouldn't generate a warning message. A warning is already in
place if both IRQs are missing.
Switch to using platform_get_irq_byname_optional() in order to facilitate
this behaviour.
Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver can register a typec port if suitable firmware properties are
present. But if the driver is removed through sysfs unbind, rmmod or
similar, then it does not clean up after itself and the typec port
device remains registered. This can be seen in sysfs, where stale typec
ports get left over in /sys/class/typec.
In order to fix this we have to add an i2c_driver remove function and
call typec_unregister_port(), which is a no-op in the case where no
typec port is created and the pointer remains NULL.
In the process we should also put the fwnode_handle when the typec port
isn't registered anymore, including if an error occurs during probe. The
typec subsystem does not increase or decrease the reference counter for
us, so we track it in the driver's private data.
Note that the conditional check on TYPEC_PWR_MODE_PD was removed in the
probe path because a call to tusb320_set_adv_pwr_mode() will perform an
even more robust validation immediately after, hence there is no
functional change here.
Fixes: bf7571c00d ("extcon: usbc-tusb320: Add USB TYPE-C support")
Cc: stable@vger.kernel.org
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lenovo Yoga Tab 3 Pro YT3-X90F needs the same handling as
the Lenovo Yogabook models. That is it needs the extcon code to:
1. Control the Vbus regulator and USB-role-switch for the micro-USB
port's host/device mode switching.
2. Register a power_supply device so that the charger-chip driver can
see what sort of charger (SDP/CDP/DCP) is connected.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230126153823.22146-4-hdegoede@redhat.com
Here is the large set of char/misc and other driver subsystem changes
for 6.2-rc1. Nothing earth-shattering in here at all, just a lot of new
driver development and minor fixes. Highlights include:
- fastrpc driver updates
- iio new drivers and updates
- habanalabs driver updates for new hardware and features
- slimbus driver updates
- speakup module parameters added to aid in boot time configuration
- i2c probe_new conversions for lots of different drivers
- other small driver fixes and additions
One semi-interesting change in here is the increase of the number of
misc dynamic minors available to 1048448 to handle new huge-cpu systems.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wrdw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykSDgCdHjUHS62/UnKdB9rLtyAOFxS/6DgAn2X4Unf8
RN8Mn2mUIiBzyu5p+Zc7
=tK3S
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc and other driver subsystem changes
for 6.2-rc1. Nothing earth-shattering in here at all, just a lot of
new driver development and minor fixes.
Highlights include:
- fastrpc driver updates
- iio new drivers and updates
- habanalabs driver updates for new hardware and features
- slimbus driver updates
- speakup module parameters added to aid in boot time configuration
- i2c probe_new conversions for lots of different drivers
- other small driver fixes and additions
One semi-interesting change in here is the increase of the number of
misc dynamic minors available to 1048448 to handle new huge-cpu
systems.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (521 commits)
extcon: usbc-tusb320: Convert to i2c's .probe_new()
extcon: rt8973: Convert to i2c's .probe_new()
extcon: fsa9480: Convert to i2c's .probe_new()
extcon: max77843: Replace irqchip mask_invert with unmask_base
chardev: fix error handling in cdev_device_add()
mcb: mcb-parse: fix error handing in chameleon_parse_gdd()
drivers: mcb: fix resource leak in mcb_probe()
coresight: etm4x: fix repeated words in comments
coresight: cti: Fix null pointer error on CTI init before ETM
coresight: trbe: remove cpuhp instance node before remove cpuhp state
counter: stm32-lptimer-cnt: fix the check on arr and cmp registers update
misc: fastrpc: Add dma_mask to fastrpc_channel_ctx
misc: fastrpc: Add mmap request assigning for static PD pool
misc: fastrpc: Safekeep mmaps on interrupted invoke
misc: fastrpc: Add support for audiopd
misc: fastrpc: Rework fastrpc_req_munmap
misc: fastrpc: Use fastrpc_map_put in fastrpc_map_create on fail
misc: fastrpc: Add fastrpc_remote_heap_alloc
misc: fastrpc: Add reserved mem support
misc: fastrpc: Rename audio protection domain to root
...
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Remove use of the deprecated mask_invert flag. Inverted mask
registers (where a '1' bit enables an IRQ) can be described more
directly as an unmask register.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently this driver triggers extcon and typec state update in its
probe function, to read out current state reported by the chip and
report the correct state to upper layers. This synchronization is
performed correctly, but only in case the chip indicates a pending
interrupt in reg09 register.
This fails to cover the situation where all interrupts reported by
the chip were already handled by Linux before reboot, then the system
rebooted, and then Linux starts again. In this case, the TUSB320 no
longer reports any interrupts in reg09, and the state update does not
perform any update as it depends on that interrupt indication.
Fix this by turning tusb320_irq_handler() into a thin wrapper around
tusb320_state_update_handler(), where the later now contains the bulk
of the code of tusb320_irq_handler(), but adds new function parameter
"force_update". The "force_update" parameter can be used by the probe
function to assure that the state synchronization is always performed,
independent of the interrupt indicated in reg09. The interrupt handler
tusb320_irq_handler() callback uses force_update=false to avoid state
updates on potential spurious interrupts and retain current behavior.
Fixes: 06bc4ca115 ("extcon: Add driver for TI TUSB320")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221120141509.81012-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bf7571c00d ("extcon: usbc-tusb320: Add USB TYPE-C support")
added an optional Type-C interface to the driver but missed to check
if it is in use when calling the IRQ handler. This causes an oops on
devices currently using the old extcon interface. Check if a Type-C
port is registered before calling the Type-C IRQ handler.
Fixes: bf7571c00d ("extcon: usbc-tusb320: Add USB TYPE-C support")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221107153317.657803-1-y.oudjana@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
Fix the warning:
drivers/extcon/extcon-usbc-tusb320.c:19: warning: expecting prototype
for drivers/extcon/extcon-tusb320.c(). Prototype was for TUSB320_REG8()
instead
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rong Chen <rong.a.chen@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The TI TUSB320 seems like a better fit for USB TYPE-C subsystem,
which can expose details collected by the TUSB320 in a far more
precise way than extcon. Since there are existing users in the
kernel and in DT which depend on the extcon interface, keep it
for now.
Add TYPE-C interface and expose the supported supply current,
direction and connector polarity via the TYPE-C interface.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Move extcon code into separate functions in preparation for addition of
USB TYPE-C support. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There's no need to set the flag explicitly to false, since that
is the default value from zero initialization.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There's no need to set the flag explicitly to false, since that
is the default value from zero initialization.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
there is an unexpected word "the" in the comments that need to be dropped
file: ./drivers/extcon/extcon.c
line: 250
/* Find the the index of extcon cable in edev->supported_cable */
changed to
/* Find the index of extcon cable in edev->supported_cable */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is an extreneous space before a dev_dbg message, remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
A remove callback that just returns 0 is equivalent to no callback at all
as can be seen in i2c_device_remove(). So simplify accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently, someone can invoke the sysfs such as state_show()
intermittently before dev_set_drvdata() is done.
And it can be a cause of kernel Oops because of edev is Null at that time.
So modified the driver registration to after setting drviver data.
- Oops's backtrace.
Backtrace:
[<c067865c>] (state_show) from [<c05222e8>] (dev_attr_show)
[<c05222c0>] (dev_attr_show) from [<c02c66e0>] (sysfs_kf_seq_show)
[<c02c6648>] (sysfs_kf_seq_show) from [<c02c496c>] (kernfs_seq_show)
[<c02c4938>] (kernfs_seq_show) from [<c025e2a0>] (seq_read)
[<c025e11c>] (seq_read) from [<c02c50a0>] (kernfs_fop_read)
[<c02c5064>] (kernfs_fop_read) from [<c0231cac>] (__vfs_read)
[<c0231c5c>] (__vfs_read) from [<c0231ee0>] (vfs_read)
[<c0231e34>] (vfs_read) from [<c0232464>] (ksys_read)
[<c02323f0>] (ksys_read) from [<c02324fc>] (sys_read)
[<c02324e4>] (sys_read) from [<c00091d0>] (__sys_trace_return)
Signed-off-by: bumwoo lee <bw365.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
While SM5502 and SM5504 are purely micro USB switching
circuits, SM5703 is a multi-function device which has multiple
modules in it. Change the i2c_device_id of it to avoid conflict
with MFD driver.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some usb controller drivers may not support extcon but use
usb role class as it's the preferred approach, so to support
usb dual role switch with usb role class, add usb role class
consumer support.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add device managed action to sync pending queue work, otherwise
the queued work may run after the work is destroyed.
Fixes: 4ed754de2d ("extcon: Add support for ptn5150 extcon driver")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
SM5703 is another MFD from Silicon Mitus which has a very similar MUIC
unit to the one in SM5502. The only difference I've noticed is slightly different
configuration only enables the interrupts which are exactly the same as on SM5502.
If we make use of different interrupts in the future, this can be improved by having
a separate struct for SM5703, but the main functionality (detecting cable or OTG adapter)
is working properly.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If disable vbus/id irq, it will lead to wakeup system fail
in unisoc platform. In unisoc platform, Irq enable and irq
wakeup are the same interrupt line. So remove disable vbus/id
irq operation is a way to solve the issue.
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add the description of @id in extcon_sync() kernel-doc comment
and @edev, @id, @prop in extcon_set_property_sync() kernel-doc
comment to remove warnings found by running scripts/kernel-doc,
which is caused by using 'make W=1'.
drivers/extcon/extcon.c:409: warning: Function parameter or
member 'id' not described in 'extcon_sync'
drivers/extcon/extcon.c:750: warning: Function parameter or
member 'edev' not described in 'extcon_set_property_sync'
drivers/extcon/extcon.c:750: warning: Function parameter or
member 'id' not described in 'extcon_set_property_sync'
drivers/extcon/extcon.c:750: warning: Function parameter or
member 'prop' not described in 'extcon_set_property_sync'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On some boards the 5V vboost-regulator for powering devices connected to
the micro USB connector is not controlled through a GPIO. This happens
for example when the 5V vboost-regulator is integrated into the charger IC
and controlled over I2C.
Add support for controlling the 5V vboost-regulator through the regulator
framework for such boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On some X86 Android tablets the DSTD lack the INT3496 ACPI device,
while also not handling micro USB port ID pin events inside the DSDT
(instead the forked factory image kernel has things hardcoded).
The new drivers/platform/x86/x86-android-tablets.c module manually
instantiates an intel-int3496 device for these tablets.
Add support to the extcon-intel-int3496 driver to bind to devices
without an ACPI companion and export a normal platform_device
modalias for automatic module loading.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Some DSDTs are buggy and do a read from the ID pin during the ACPI
initialization, causing the pin to be marked as owned by:
"ACPI:OpRegion" and causing gpiod_get() to fail with -EBUSY.
Pass the GPIOD_FLAGS_BIT_NONEXCLUSIVE flag to the gpiod_get() call
to work around this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On all devices which I have with an INT3496 ACPI device,
there is only an ID pin defined.
Change the log-messages about not being able to get GPIOs for
"VBUS EN" and "USB MUX" to use dev_dbg().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Make cht_wc_extcon_get_id() report RID_A for ACA adapters, instead of
reporting ID_FLOAT.
According to the spec. we should read the USB-ID pin ADC value
to determine the resistance of the used pull-down resister and
then return RID_A / RID_B / RID_C based on this. But all "Accessory
Charger Adapter"s (ACAs) which users can actually buy always use
a combination of a charging port with one or more USB-A ports, so
they should always use a resistor indicating RID_A. But the spec
is hard to read / badly-worded so some of them actually indicate
they are a RID_B ACA even though they clearly are a RID_A ACA.
To workaround this simply always return INTEL_USB_RID_A, which
matches all the ACAs which users can actually buy.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25890 used on the Yogabook YB1-X90 / -X91 models relies on
the extcon-driver's BC-1.2 charger detection, and the bq25890 driver
expect this info to be available through a parent power_supply
class-device which models the detected charger (idem to how the Type-C
TCPM code registers a power_supply classdev for the connected charger).
Add support for registering the power_supply class-device expected
by this setup.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This is a preparation patch for adding support for registering
a power_supply class device.
Setting usbsrc to "CHT_WC_USBSRC_TYPE_SDP << CHT_WC_USBSRC_TYPE_SHIFT"
will make the following switch-case return EXTCON_CHG_USB_SDP
just as before, so there is no functional change.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
So far the extcon-intel-cht-wc code has only been tested on devices with
a Type-C connector with USB-PD, USB3 (superspeed) and DP-altmode support
through a FUSB302 Type-C controller.
Some devices with the intel-cht-wc PMIC however come with an USB-micro-B
connector, or an USB-2 only Type-C connector without USB-PD.
Which device-model we are running on can be identified with the new
cht_wc_model intel_soc_pmic field. On models without a Type-C controller
the extcon code must control the Vbus 5V boost converter and the USB role
switch depending on the detected cable-type.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The CHT_WC_VBUS_GPIO_CTLO GPIO actually driving an external 5V Vboost
converter for Vbus depends on the board on which the Cherry Trail -
Whiskey Cove PMIC is actually used.
Since the information about the exact PMIC setup is necessary in other
places too, struct intel_soc_pmic now has a new cht_wc_model field
indicating the board model.
Only poke the CHT_WC_VBUS_GPIO_CTLO GPIO if this new field is set to
INTEL_CHT_WC_GPD_WIN_POCKET, which indicates the Type-C (with PD and
DP-altmode) setup used on the GPD pocket and GPD win; and on which
this GPIO actually controls an external 5V Vboost converter.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Finding the cable index and checking for changed status is also done
in extcon_set_state(). So calling extcon_set_state_sync() will do these
checks twice. Remove them and use these checks from extcon_set_state().
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Do not use "/**" to begin a non-kernel-doc comment.
Fixes this build warning:
drivers/extcon/extcon-usb-gpio.c:23:
warning: expecting prototype for drivers/extcon/extcon-usb-gpio.c().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
TUSB320L is a newer chip with additional features, and it has additional steps
in its mode changing sequence:
- Disable CC state machine,
- Write to mode register,
- Wait for 5 ms,
- Re-enable CC state machine.
It also has an additional register that a revision number can be read from.
Add support for the mode changing sequence, and read the revision number during
probe and print it as info.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
