<asm/systemcfg.h> is gone now, and the PCI error recovery constants
in include/linux/pci.h changed their names in the process of getting
accepted.
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 5a2516156c591fc3d2059fbd93f97e15eb6010d6 commit)
242-eeh-no-percpu-counters.patch
Remove per-cpu counters from the EEH code. These statistics counters
are incremented at a very low frequency, and the performance gains of
per-cpu variables are negligable. By contrast, the counters weren't
safe against cpu off/online operations, and its not worth the effort
to make them so (other than to turn them into plain globals).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from be3b5d1be053ccb41e91fa5a6f43ef5db301357d commit)
241-eeh-save-bars-earlier.patch
Save the PCI device bars *before* any PCI probing is done.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 76c902b919098860f3d4e125f847abcc4cb1782a commit)
239-eeh-multifunction-consolidate.patch
New-style firmware will often place multiple different functions
under a non-EEH-aware parent. However, these devices might share
a common PE "partition endpoint" and config address, ad thus any
EEH events will affect all of the devices in common. This patch
makes the effort to find all of these common devices and handle
them together.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 216810296bb97d39da8e176822e9de78d2f00187 commit)
238-eeh-stop-if-reset_failed.patch
If the firmware is unable to reset the PCI slot for some reason, then
don't attempt any further recovery steps after that point. Instead,
mark the device as permanently failed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e06b942521eb2cdaf232726f45a820d5837acb12 commit)
237-eeh-bridge-token.patch
Minor: the rtas-bridge token should be set up the same way that all
the other rtas tokens are set up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 78379b6c5fc17b6666c40b05988e6708e98479c0 commit)
236-eeh-config-addr.patch
The PE configuration address wasn't being cnsistently used in all locations
where a config address is called for. This patch adds it to the places it
should have appeared in.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from c2bc904a28095aca0b04a37854b63b78622a032e commit)
235-eeh-set-pcidev-bugfix.patch
The pci device field of the pci_dn struct should be initialized to a
valid value.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from beb45c93d494a11c36e5b24f638e610db8428b54 commit)
234-eeh-find-pe.patch
The find_device_pe() routine is duplicated in two files. Remove one of
the two copies, declare the other extern.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 48408e708282d4d0269136ff27ea5acbd9410b5a commit)
26-eeh-partition-endpoint.patch
New versions of firmware introduce a new method by which the
"partitionable endpoint" (the point at which the pci bus is cut)
should be located. This code adds the support for this (mandatory)
new feature.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 9fcfb5d35b5294659f9299aa9cae6fd16325c07e commit)
25-pci-address-cache.patch
The core EEH file is rather large. This patch splits out a self-contained
chunk of it into its own file. This is the chunk that performes the
caching and lookup of pci devices based on the i/o addresses of thier
resoures. This code is almos architecture-independent and could be
used by any system that wanted to find a pci device based only on
the i/o address used by the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from b0b291d59906d4a9a89ed9e34d9fd684c7188924 commit)
Various PCI bus errors can be signaled by newer PCI controllers. The
core error recovery routines are architecture dependent. This patch adds
a recovery infrastructure for the PPC64 pSeries systems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e8ca11b460c4c9c7fa6b529be221529ebd770e38 commit)
This patch enables support for pause(0) power management state
for the Cell Broadband Processor, which is import for power efficient
operation. The pervasive infrastructure will in the future enable
us to introduce more functionality specific to the Cell's
pervasive unit.
From: Maximino Aguilar <maguilar@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, we are not looking at all interrupt controller nodes in the
device tree even though the proper node was not found. This is causing
the system panic. The attached patch will scan all nodes until it finds
the proper interrupt controller type.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is code in the RPAPHP directory that is identical to this routine;
I'll be removing that code in an upcoming patch, but this patch is needed
to expose the function to make it callable.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implementing the machine_crash_shutdown which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Disable the
interrupts, shootdown cpus using debugger IPI and collect regs
for all CPUs.
elfcorehdr= specifies the location of elf core header stored by
the crashed kernel. This command line option will be passed by
the kexec-tools to capture kernel.
savemaxmem= specifies the actual memory size that the first kernel
has and this value will be used for dumping in the capture kernel.
This command line option will be passed by the kexec-tools to
capture kernel.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fwnmi vectors can be anywhere < 32 MB, so we need to use a trampoline
for them. The kdump kernel will register the trampoline addresses, which will
then jump up to the real code above 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Minor: use macro to perform void pointer deref; this may someday help
avoid pointer typecasting errors.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The udbg low level io layer has an issue with udbg_getc() returning a
char (unsigned on ppc) instead of an int, thus the -1 if you had no
available input device could end up turned into 0xff, filling your
display with bogus characters. This fixes it, along with adding a little
blob to xmon to do a delay before exiting when getting an EOF and fixing
the detection of ADB keyboards in udbg_adb.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
23-rpaphp-migrate.patch (parts)
This patch moves some pci device add & remove code from the PCI
hotplug directory to the arch/powerpc/kernel directory, and cleans
it up a tad. The primary reason for this is that the code performs
some fairly generic operations that are shared with the PCI error
recovery code (living in the arch/powerpc/kernel directory).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
20-rpaphp-eeh-cleanup.patch
This patch move some code from the rpaphp directory, to the powerpc
directory, where it should have been all along (Among other things, I
need it in the powerpc directory for the PCI error recovery.)
Please note that patch affects TWO maintainers: Paul, after applying
the powerpc part, please ask that GregKH appli the PCI part. It is safe
to have the powerpc part go in first. It would be bad to have the
PCI part go in first.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.
Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.
It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It turns out that commit f9bd170a87
broke the cascade from XICS to i8259 on pSeries machines; specifically
we ended up not ever doing the EOI on the XICS for the cascade. The
result was that interrupts from the serial ports (and presumably any
other devices using ISA interrupts) didn't get through. This fixes
it and also simplifies the code, by doing the EOI on the XICS in the
xics_get_irq routine after reading and acking the interrupt on the
i8259.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous commit will use the page-at-a-time hypervisor call for
setting up IOMMU entries when we are using 64k pages and setting up
one 64k page, even though that means 16 calls to the hypervisor, since
the hypervisor still works on 4k pages. This optimizes this case by
using the multi-page IOMMU setup hypervisor call instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Must adjust tcenum and npages by TCE_PAGE_FACTOR to convert between
64KB pages and TCE (4K) pages. (This is done in other places, except
for this one location.)
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Email address update, changing old work address to personal (permanent)
one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_dedicated_idle() was using __get_tb which used to be defined
in asm/delay.h. Change it to use get_tb from asm/time.h, which is
in fact exactly the same thing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the kernel supports both G5 and pSeries, and CONFIG_EEH is enabled,
eeh_init() is (quite reasonably) never called when we boot on a G5. Yet
eeh_check_failure() still gets called. We should avoid doing that if
!eeh_subsystem_enabled.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also deletes files in arch/ppc64 that are no longer used now that
we don't compile with ARCH=ppc64 any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a ppc_md member called cpu_irq_down, which disables IRQs
for the cpu in question. The only caller of cpu_irq_down is the kexec code.
On pSeries we need to do more than just teardown IRQs at kexec time, so rename
the ppc_md member to kexec_cpu_down and expand it. The pSeries code needs to
know, and other platforms might too, whether we're doing a crash shutdown (ie.
panicking) or a regular kexec, so add a flag for that.
The pSeries implementation of kexec_cpu_down does an unregister VPA call, which
tells the Hypervisor to stop writing stuff into our pacas. Without this we can
get weird memory corruption bugs when we kexec, caused by the Hypervisor
writing into the first kernel's pacas which happens to be somewhere interesting
in the second kernel's memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We needed the VDSO symbols in the arch/ppc asm-offsets.c, and there
were a few usages of _systemcfg still left lying around.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have been printing the raw ppc64_firmware_features during boot. Since
we can work it out from the device tree, lets remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
17-eeh-slot-marking-bug.patch
A device that experiences a PCI outage may be just one deivce out
of many that was affected. In order to avoid repeated reports of
a failure, the entire tree of affected devices should be marked
as failed. This patch marks up the entire tree.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
phbs_remap_io(), which maps the PCI IO space into the kernel virtual space,
is called too early on powermac, and thus doesn't work.
This fixes it by removing the call from all platforms and putting it back
into the ppc64 common code where it belongs, after the actual probing of
the bus.
That means that before that call, only the ISA IO space (if any) is mapped,
any PIO access (from quirks for example) will fail. This happens not to be
a problem for now, but we'll have to rework that code if it becomes one in
the future.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
scanlog.c is only compiled on pSeries. Thus, this patch moves it to
platforms/pseries.
Built and booted on pSeries LPAR (ARCH=powerpc and ARCH=ppc64). Built
for iSeries (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
14-eeh-device-bar-save.patch
After a PCI device has been resest, the device BAR's and other config
space info must be restored to the same state as they were in when
the firmware first handed us this device. This will allow the
PCI device driver, when restarted, to correctly recognize and set up
the device.
Tis patch saves the device config space as early as reasonable after
the firmware has handed over the device. Te state resore funcion
is inteded for use by the EEH recovery routines.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
13-eeh-recovery-support-routines.patch
EEH Recovery support routines
This patch adds routines required to help drive the recovery of
EEH-frozen slots. The main function is to drive the PCI #RST
signal line high for a qurter of a second, and then allow for
a second & a half of settle time.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
12-eeh-event-dispatcher.patch
ppc64: EEH Recovery dispatcher thread
This patch adds a mechanism to create recovery threads when an
EEH event is received. Since an EEH freeze state may be detected
within an interrupt context, we need to get out of the interrupt
context before starting recovery. This dispatcher does this in
two steps: first, it uses a workqueue to get out, and then
lanuches a kernel thread, so that the recovery routine can
sleep for exteded periods without upseting the keventd.
A kernel thread is created with each EEH event, rather than
having one long-running daemon started at boot time. This is
because it is anticipated that EEH events will be very rare
(very very rare, ideally) and so its pointless to cluter the
process tables with a daemon that will almost never run.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
11-eeh-move-to-powerpc.patch
Move arch/ppc64/kernel/eeh.c to arch//powerpc/platforms/pseries/eeh.c
No other changes (except for Makefile to build it)
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __do_IRQ instead. The only difference is that every controller
is now assumed to have an end() routine (only xics_8259 did not).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
