When using firmware assisted TSO, we use a single DMA mapping for
the linear area of a TSO skb.
We still have to segment the super-packet and insert a descriptor
containing the original headers before each segment of payload, so we
can unmap the linear area only after the last segment is completed.
The unmapping information for the linear area is therefore associated
with the last header descriptor.
We calculate the DMA address to unmap from using the map length and
the invariant that the end of the DMA mapping matches the end of
the data referenced by the last descriptor. But this invariant is
broken when there is TCP payload in the linear area.
Fix this by adding and using an explicit dma_offset field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we do not yet enable multiple PFs per port, it is possible
that a board will be reconfigured to enable them while the driver has
not yet been updated to fully support this.
The most obvious problem is that multiple functions may try to set
conflicting link settings. But we will also run into trouble if the
firmware doesn't consider us fully trusted. So, abort probing unless
both the LinkCtrl and Trusted flags are set for this function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Recognise the new Packet Memory and RX Data Path counters.
The following counters are added:
rx_pm_{trunc,discard}_bb_overflow - burst buffer overflowed. This should not
occur if BB correctly configured.
rx_pm_{trunc,discard}_vfifo_full - not enough space in packet memory. May
indicate RX performance problems.
rx_pm_{trunc,discard}_qbb - dropped by 802.1Qbb early discard mechanism.
Since Qbb is not supported at present, this should not occur.
rx_pm_discard_mapping - 802.1p priority configured to be dropped. This should
not occur in normal operation.
rx_dp_q_disabled_packets - packet was to be delivered to a queue but queue is
disabled. May indicate misconfiguration by the driver.
rx_dp_di_dropped_packets - parser-dispatcher indicated that a packet should be
dropped.
rx_dp_streaming_packets - packet was sent to the RXDP streaming bus, ie. a
filter directed the packet to the MCPU.
rx_dp_emerg_{fetch,wait} - RX datapath had to wait for descriptors to be
loaded. Indicates performance problems but not drops.
These are only provided if the MC firmware has the
PM_AND_RXDP_COUNTERS capability. Otherwise, mask them out.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Previously, efx_ef10_stat_mask returned a static const unsigned long[], which
meant that each possible mask had to be declared statically with
STAT_MASK_BITMAP. Since adding a condition would double the size of the
decision tree, we now create the bitmask dynamically.
To do this, we have two functions efx_ef10_raw_stat_mask, which returns a u64,
and efx_ef10_get_stat_mask, which fills in an unsigned long * argument.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The indices in nic_data->stats need to match the EF10_STAT_whatever
enum values. In efx_nic_update_stats, only mask; gaps are removed in
efx_ef10_update_stats.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Extend efx_filter_rfs() to map TCP/IPv6 and UDP/IPv6 flows into
efx_filter_spec. These are only supported on EF10; on Falcon and
Siena they will be rejected by efx_farch_filter_from_gen_spec().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Sufficiently small linear packets can be copied into the PIO buffer
with a single call to memcpy_toio(). Non-linear packets require an
intermediate cache-line-sized buffer.
[bwh: I wrote the first version of this, but Jon did the hard work to
handle non-linear packets.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Try to allocate a segment of PIO buffer to each TX channel. If
allocation fails, log an error but continue.
PIO buffers must be mapped separately from the NIC registers, with
write-combining enabled. Where the host page size is 4K, we could
potentially map each VI's registers and PIO buffer separately.
However, this would add significant complexity, and we also need to
support architectures such as POWER which have a greater page size.
So make a single contiguous write-combining mapping after the
uncacheable mapping, aligned to the host page size, and link PIO
buffers there. Where necessary, allocate additional VIs within
the write-combining mapping purely for access to PIO buffers.
Link all TX buffers to TX queues and the additional VIs in
efx_ef10_dimension_resources() and in efx_ef10_init_nic() after
an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Segmentation remains in the driver, but we generate option descriptors
describing the required packet editing rather than making our own
copies.
Reduce tso_state::ipv4_id to 16 bits, so it doesn't overflow into the
TCP_FLAGS field of the option descriptor.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Scheduling a reset following an MC reboot event before waiting for
reboot to complete results in a race that can lead to a state where
must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have
been destroyed during the MC reboot.
To avoid MC errors when trying to remove VIs that do not exist, wait
for the MC reboot to complete before scheduling the reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings says:
====================
Some bug fixes and future-proofing for the recently added SFC9120
support:
1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After an MC reboot, the datapath may be running a different firmware
variant and have different capabilities. It is critical that we know
the current capabilities so that we can pass valid flags to
MC_CMD_INIT_EVQ.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Rename efx_ef10_init_capabilities() to the more specific
efx_ef10_init_datapath_caps().
Stop accepting short responses to MC_CMD_GET_CAPABILITIES; we
don't need to support pre-production firmware.
Move the check for RX prefix support from efx_ef10_probe() into
efx_ef10_init_datapath_caps() and use consistent error messages
for missing TSO support and missing RX prefix support.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
If the MC reboots then the stats it reports to us will have been
reset. We need to reset ours to get efx_update_diff_stat() working
properly.
(This is a re-run of commit 876be083b6 'sfc: Reset driver's
MAC stats after MC reboot seen'.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Unlike Siena where timestamping is provided by a peripheral, EF10
delivers RX timestamps in the packet prefix. However the driver
doesn't yet support this.
We are also creating a PHC device for each EF10 function, even though
the clock is really shared between all of them.
Disable hardware PTP/timestamping support until it's complete.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Accept and handle 40G link events.
Accept ethtool link settings of speed == 40000 && duplex, and set the
appropriate MCDI PHY capability.
This does not include reporting of 40G media types, as those have not
yet been assigned numbers in the MCDI protocol.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
It upsets static analyzers when we don't check for allocation failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. A little more refactoring.
2. Remove the unnecessary use of atomic_t that you pointed out.
3. Add support for starting or queueing firmware requests from atomic
context.
4. Add hwmon support for additional sensors found on some new boards.
5. Add support for the EF10 controller architecture, the SFC9100 family
and specifically the SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dates for files that have been added to in 2012-2013.
Drop the 'Solarstorm' brand name that's still lingering here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This adds support for the EF10 network controller architecture and the
SFC9100 family, starting with SFC9120 'Farmingdale', and bumps the
driver version to 4.0.
New features in the SFC9100 family include:
- Flexible allocation of internal resources to PCIe physical and virtual
functions under firmware control
- RX event merging to reduce DMA writes at high packet rates
- Integrated RX timestamping
- PIO buffers for lower TX latency
- Firmware-driven data path that supports additional offload features
and filter types
- Delivery of packets between functions and to multiple recipients,
allowing firmware to implement a vswitch
- Multiple RX flow hash (RSS) contexts with their own hash keys and
indirection tables
- 40G MAC (single port only)
...not all of which are enabled in this initial driver or the initial
firmware release.
Much of the new code is by Jon Cooper.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Also update comments and assertions in io.h:
- EF10 does not have a general BIU collector and does not have the
bug affecting TIMER_COMMAND_REG[0] on Falcon/Siena
- The WPTR field moved within RX_DESC_UPD_REG and TX_DESC_UPD_REG.
Adjust efx_writed_page() accordingly
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The TX path firmware for EF10 supports 'option descriptors' to control
offloads and various other features. Add a flag and field for these
in struct efx_tx_buffer, and don't treat them as DMA descriptors on
completion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On EF10, the firmware will initiate a queue flush in certain
error cases. We need to accept that flush events might appear
at any time after a queue has been initialised, not just when
we try to flush them.
We can handle Falcon-architecture in just the same way.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
RX DMA scatter is always enabled on EF10. Adjust the common RX
completion handling to allow for this.
RX completion events on EF10 include the length used from a single
descriptor, not the cumulative length used. Add a field to struct
efx_rx_queue to hold the cumulative length.
[bwh: Also fix a related comment]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add the efx_filter_is_mc_recip() function to decide whether a filter
is for a multicast recipient and can coexist with other filters with
the same match values. Update efx_filter_insert_filter() kernel-doc
to explain the conditions for this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We can set, get and compare-and-exchange without using atomic_t.
Change efx_mcdi_iface::state to the enum type we really wanted it to
be.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add support for power and current sensors, which need to be named
differently in sysfs. Power sensors also require values to be scaled
between MCDI and sysfs, and have no minimum value.
Add definitions of the power, current, fan, and additional temperature
and voltage sensors found on SFA6902F, SFN7022F and SFN7122F.
(Includes a bug fix from Andrew Jackson.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Define a flag for struct efx_rx_buffer and efx_rx_packet() that
indicates packet length must be read from the prefix. If this
is set, read the length in __efx_rx_packet() (when the prefix
should have arrived in cache).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
