The TiWi WL1251 WiFi chip needs special setup of the sdio
interface before it can be probed.
So far, this is done in omap_hsmmc_init_card() in omap_hsmmc.c
which makes it useable only if connected to omap devices
which use the omap_hsmmc. The OpenPandora is the most promient
example.
There are plans to switch to a newer sdhci-omap driver and
retire omap_hsmmc. Hence this quirk must be reworked or moved
somewhere else. Ideally to some location that is not dependent
on the specific SoC mmc host driver.
This is achieved by the new mmc_fixup_device() option introduced
by ("mmc: allow to match the device tree to apply quirks") to match
through device tree compatible string.
This quirk will be called early right after where host->ops->init_card()
and thus omap_hsmmc_init_card() was previously called.
Note that we do not need to transplant
card->ocr = 0x80;
because we rely on ("mmc: core: Fixup storing of OCR for MMC_QUIRK_NONSTD_SDIO").
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/774565df7f02124c003aaf8b879706352548f832.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This (initially empty) table allows to match quirks early based
on .compatible of the child node of some mmc/sdio interface.
This allows to add quirks based on device tree instead of having
card specific code in the host ops.
A new macro SDIO_FIXUP_COMPATIBLE makes the definition readable.
And we call mmc_fixup_device(sdio_card_init_methods) just after
where host->ops->init_card() can be optionally called.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/b13fd8b3eebc3c23b6816b254a518c224cbdcfd4.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC subsystem provides a way to apply quirks when a device match some
properties (VID, PID, etc...) Unfortunately, some SDIO devices do not
comply with the SDIO specification and does not provide reliable VID/PID
(eg. Silabs WF200).
So, the drivers for these devices rely on device tree to identify the
device.
This patch allows the MMC to also rely on the device tree to apply a
quirk.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/9e68e3d23e62a78527aabc1281f89e15200c7d09.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, mmc_fixup_device() is a bit difficult to read because of
particularly long condition.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/6515c1e8b3aa69ad273726f6e877d85c20f286ad.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor the code so that card detect irqs are always reenabled after a
reset. This avoids doing it manually all over the code or forgetting to
do this in the future.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
[wsa: added a comment when 'native_hotplug' has to be set]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211103122646.64422-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'cmd_error' is not necessarily initialized on some error paths in
mmc_send_tuning(). Initialize it.
Fixes: 2c9017d0b5 ("mmc: renesas_sdhi: abort tuning when timeout detected")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211130132309.18246-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_id is
missing for the MMC SPI driver and the following warning is now seen.
WARNING KERN SPI driver mmc_spi has no spi_device_id for mmc-spi-slot
Fix this by adding the necessary spi_device_id.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20211115113813.238044-1-jonathanh@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block layer forces a minimum segment size of PAGE_SIZE, so a segment
can be too big for the ADMA table, if PAGE_SIZE >= 64KiB. Fix by writing
multiple descriptors, noting that the ADMA table is sized for 4KiB chunks
anyway, so it will be big enough.
Reported-and-tested-by: Bough Chen <haibo.chen@nxp.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211115082345.802238-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge misc updates from Andrew Morton:
"257 patches.
Subsystems affected by this patch series: scripts, ocfs2, vfs, and
mm (slab-generic, slab, slub, kconfig, dax, kasan, debug, pagecache,
gup, swap, memcg, pagemap, mprotect, mremap, iomap, tracing, vmalloc,
pagealloc, memory-failure, hugetlb, userfaultfd, vmscan, tools,
memblock, oom-kill, hugetlbfs, migration, thp, readahead, nommu, ksm,
vmstat, madvise, memory-hotplug, rmap, zsmalloc, highmem, zram,
cleanups, kfence, and damon)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (257 commits)
mm/damon: remove return value from before_terminate callback
mm/damon: fix a few spelling mistakes in comments and a pr_debug message
mm/damon: simplify stop mechanism
Docs/admin-guide/mm/pagemap: wordsmith page flags descriptions
Docs/admin-guide/mm/damon/start: simplify the content
Docs/admin-guide/mm/damon/start: fix a wrong link
Docs/admin-guide/mm/damon/start: fix wrong example commands
mm/damon/dbgfs: add adaptive_targets list check before enable monitor_on
mm/damon: remove unnecessary variable initialization
Documentation/admin-guide/mm/damon: add a document for DAMON_RECLAIM
mm/damon: introduce DAMON-based Reclamation (DAMON_RECLAIM)
selftests/damon: support watermarks
mm/damon/dbgfs: support watermarks
mm/damon/schemes: activate schemes based on a watermarks mechanism
tools/selftests/damon: update for regions prioritization of schemes
mm/damon/dbgfs: support prioritization weights
mm/damon/vaddr,paddr: support pageout prioritization
mm/damon/schemes: prioritize regions within the quotas
mm/damon/selftests: support schemes quotas
mm/damon/dbgfs: support quotas of schemes
...
nr_free_buffer_pages could be exposed through mm.h instead of swap.h.
The advantage of this change is that it can reduce the obsolete
includes. For example, net/ipv4/tcp.c wouldn't need swap.h any more
since it has already included mm.h. Similarly, after checking all the
other files, it comes that tcp.c, udp.c meter.c ,... follow the same
rule, so these files can have swap.h removed too.
Moreover, after preprocessing all the files that use
nr_free_buffer_pages, it turns out that those files have already
included mm.h.Thus, we can move nr_free_buffer_pages from swap.h to mm.h
safely. This change will not affect the compilation of other files.
Link: https://lkml.kernel.org/r/20210912133640.1624-1-liumh1@shanghaitech.edu.cn
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Cc: Jakub Kicinski <kuba@kernel.org>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Simon Horman <horms@verge.net.au>
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Update maintainer and URL for the mmc-utils
- Set default label for slot-gpio in case of no con-id
- Convert MMC card DT bindings to a schema
- Add optional host specific tuning support for eMMC HS400
- Add error handling of add_disk()
MMC host:
- mtk-sd: Add host specific tuning support for eMMC HS400
- mtk-sd: Make DMA handling more robust
- dw_mmc: Prevent hangs for some data writes
- dw_mmc: Move away from using the ->init_card() callback
- mxs-mmc: Manage the regulator in the error path and in ->remove()
- sdhci-cadence: Add support for the Microchip MPFS variant
- sdhci-esdhc-imx: Add support for the NXP S32G2 variant
- sdhci-of-arasan: Add support for the Intel Thunder Bay variant
- sdhci-omap: Prepare to support more SoCs
- sdhci-omap: Add support for omap3 and omap4 variants
- sdhci-omap: Add support for power management
- sdhci-omap: Add support for system wakeups
- sdhci-msm: Add support for the msm8226 variant
- sdhci-sprd: Verify that the DLL locks according to spec
MEMSTICK:
- Add error handling of add_disk()
- A couple of small fixes and improvements
-----BEGIN PGP SIGNATURE-----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=W+gH
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Update maintainer and URL for the mmc-utils
- Set default label for slot-gpio in case of no con-id
- Convert MMC card DT bindings to a schema
- Add optional host specific tuning support for eMMC HS400
- Add error handling of add_disk()
MMC host:
- mtk-sd: Add host specific tuning support for eMMC HS400
- mtk-sd: Make DMA handling more robust
- dw_mmc: Prevent hangs for some data writes
- dw_mmc: Move away from using the ->init_card() callback
- mxs-mmc: Manage the regulator in the error path and in ->remove()
- sdhci-cadence: Add support for the Microchip MPFS variant
- sdhci-esdhc-imx: Add support for the NXP S32G2 variant
- sdhci-of-arasan: Add support for the Intel Thunder Bay variant
- sdhci-omap: Prepare to support more SoCs
- sdhci-omap: Add support for omap3 and omap4 variants
- sdhci-omap: Add support for power management
- sdhci-omap: Add support for system wakeups
- sdhci-msm: Add support for the msm8226 variant
- sdhci-sprd: Verify that the DLL locks according to spec
MEMSTICK:
- Add error handling of add_disk()
- A couple of small fixes and improvements"
* tag 'mmc-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (60 commits)
docs: mmc: update maintainer name and URL
mmc: dw_mmc: exynos: Fix spelling mistake "candiates" -> candidates
MAINTAINERS: drop obsolete file pattern in SDHCI DRIVER section
mmc: sdhci-esdhc-imx: add NXP S32G2 support
dt-bindings: mmc: fsl-imx-esdhc: add NXP S32G2 support
mmc: dw_mmc: Drop use of ->init_card() callback
mmc: sdhci-omap: Fix build if CONFIG_PM_SLEEP is not set
mmc: sdhci-omap: Remove forward declaration of sdhci_omap_context_save()
memstick: r592: Fix a UAF bug when removing the driver
mmc: mxs-mmc: disable regulator on error and in the remove function
mmc: sdhci-omap: Configure optional wakeirq
mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM
mmc: sdhci-omap: Implement PM runtime functions
mmc: sdhci-omap: Add omap_offset to support omap3 and earlier
mmc: sdhci-omap: Handle voltages to add support omap4
dt-bindings: sdhci-omap: Update binding for legacy SoCs
mmc: sdhci-pci: Remove dead code (rst_n_gpio et al)
mmc: sdhci-pci: Remove dead code (cd_gpio, cd_irq et al)
mmc: sdhci-pci: Remove dead code (struct sdhci_pci_data et al)
mmc: sdhci: Remove unused prototype declaration in the header
...
-----BEGIN PGP SIGNATURE-----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=dLYJ
-----END PGP SIGNATURE-----
Merge tag 'for-5.16/passthrough-flag-2021-10-29' of git://git.kernel.dk/linux-block
Pull QUEUE_FLAG_SCSI_PASSTHROUGH removal from Jens Axboe:
"This contains a series leading to the removal of the
QUEUE_FLAG_SCSI_PASSTHROUGH queue flag"
* tag 'for-5.16/passthrough-flag-2021-10-29' of git://git.kernel.dk/linux-block:
block: remove blk_{get,put}_request
block: remove QUEUE_FLAG_SCSI_PASSTHROUGH
block: remove the initialize_rq_fn blk_mq_ops method
scsi: add a scsi_alloc_request helper
bsg-lib: initialize the bsg_job in bsg_transport_sg_io_fn
nfsd/blocklayout: use ->get_unique_id instead of sending SCSI commands
sd: implement ->get_unique_id
block: add a ->get_unique_id method
-----BEGIN PGP SIGNATURE-----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=QWC+
-----END PGP SIGNATURE-----
Merge tag 'for-5.16/block-2021-10-29' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- mq-deadline accounting improvements (Bart)
- blk-wbt timer fix (Andrea)
- Untangle the block layer includes (Christoph)
- Rework the poll support to be bio based, which will enable adding
support for polling for bio based drivers (Christoph)
- Block layer core support for multi-actuator drives (Damien)
- blk-crypto improvements (Eric)
- Batched tag allocation support (me)
- Request completion batching support (me)
- Plugging improvements (me)
- Shared tag set improvements (John)
- Concurrent queue quiesce support (Ming)
- Cache bdev in ->private_data for block devices (Pavel)
- bdev dio improvements (Pavel)
- Block device invalidation and block size improvements (Xie)
- Various cleanups, fixes, and improvements (Christoph, Jackie,
Masahira, Tejun, Yu, Pavel, Zheng, me)
* tag 'for-5.16/block-2021-10-29' of git://git.kernel.dk/linux-block: (174 commits)
blk-mq-debugfs: Show active requests per queue for shared tags
block: improve readability of blk_mq_end_request_batch()
virtio-blk: Use blk_validate_block_size() to validate block size
loop: Use blk_validate_block_size() to validate block size
nbd: Use blk_validate_block_size() to validate block size
block: Add a helper to validate the block size
block: re-flow blk_mq_rq_ctx_init()
block: prefetch request to be initialized
block: pass in blk_mq_tags to blk_mq_rq_ctx_init()
block: add rq_flags to struct blk_mq_alloc_data
block: add async version of bio_set_polled
block: kill DIO_MULTI_BIO
block: kill unused polling bits in __blkdev_direct_IO()
block: avoid extra iter advance with async iocb
block: Add independent access ranges support
blk-mq: don't issue request directly in case that current is to be blocked
sbitmap: silence data race warning
blk-cgroup: synchronize blkg creation against policy deactivation
block: refactor bio_iov_bvec_set()
block: add single bio async direct IO helper
...
These are now pointless wrappers around blk_mq_{alloc,free}_request,
so remove them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20211025070517.1548584-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The reset callback may clear the internal card detect interrupts, so
make sure to reenable them if needed.
Fixes: b4d86f37ea ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211028195149.8003-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We must enable clock before cqhci init, because crypto needs read
information from CQHCI registers, otherwise, it will hang in MediaTek mmc
host controller.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Acked-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20211028022049.22129-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support the SDHCI controller found on NXP S32G2 platform. The new flag
ESDHC_FLAG_SKIP_ERR004536 is used because the hardware erratum bit is not
applicable for S32G2.
Signed-off-by: Chester Lin <clin@suse.com>
Link: https://lore.kernel.org/r/20211021071333.32485-3-clin@suse.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While mmc0 enter suspend state, we need halt CQE to send legacy cmd(flush
cache) and disable cqe, for resume back, we enable CQE and not clear HALT
state.
In this case MediaTek mmc host controller will keep the value for HALT
state after CQE disable/enable flow, so the next CQE transfer after resume
will be timeout due to CQE is in HALT state, the log as below:
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: timeout for tag 2
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Caps: 0x100020b6 | Version: 0x00000510
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Config: 0x00001103 | Control: 0x00000001
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: TDL base: 0xfd05f000 | TDL up32: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Doorbell: 0x8000203c | TCN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Task clr: 0x00000000 | SSC1: 0x00001000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQP: 0x00000000 | CRNQDUN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQIS: 0x00000000 | CRNQIE: 0x00000000
This change check HALT state after CQE enable, if CQE is in HALT state, we
will clear it.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Link: https://lore.kernel.org/r/20211026070812.9359-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though there are candiates value if can't find best value, it's
returned -EIO. It's not proper behavior.
If there is not best value, use a first candiate value to work eMMC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Cc: stable@vger.kernel.org
Fixes: c537a1c5ff ("mmc: dw_mmc: exynos: add variable delay tuning sequence")
Link: https://lore.kernel.org/r/20211022082106.1557-1-jh80.chung@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For dw_mmc, the ->init_card() callback is being used to turn on/off
automatic internal clock gating for powersave, which is needed to properly
support SDIO irqs on DAT1.
However, using the ->init_card() comes with a drawback in this case, as it
means that the powersave feature becomes disabled, no matter whether the
SDIO irqs becomes turned on or not. To improve the behaviour, let's change
into using the ->enable_sdio_irq() callback instead. This works fine,
because dw_mmc uses sdio_signal_irq() to signal the irqs, thus the
->enable_sdio_irq() is never executed from within atomic context.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211020102907.70195-1-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
combined the use of runtime PM and system suspend functions but left the
ifdef CONFIG_PM_SLEEP in place causing undeclared identifier error for
sdhci_omap_runtime_suspend if CONFIG_PM_SLEEP is not enabled.
Let's fix the error by removing ifdef CONFIG_PM_SLEEP and tagging the
reset of the PM related functions with __maybe_unused.
Let's also remove the forward declaration for sdhci_omap_context_save(),
that was accidentally left from an earlier version and is no longer used.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Ulf: Rebased and fixed build error]
Link: https://lore.kernel.org/r/20211021134352.10135-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If CONFIG_PM_SLEEP=n:
drivers/mmc/host/sdhci-omap.c:1213:13: error: ‘sdhci_omap_context_save’ declared ‘static’ but never defined [-Werror=unused-function]
1213 | static void sdhci_omap_context_save(struct sdhci_omap_host *omap_host);
| ^~~~~~~~~~~~~~~~~~~~~~~
The referenced commit added an unrelated forward declaration of
sdhci_omap_context_save(), which is unneeded in general, and unused when
CONFIG_PM_SLEEP=n.
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Reported-by: noreply@ellerman.id.au
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211020083902.3669769-1-geert@linux-m68k.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
blk_keyslot_manager is misnamed because it doesn't necessarily manage
keyslots. It actually does several different things:
- Contains the crypto capabilities of the device.
- Provides functions to control the inline encryption hardware.
Originally these were just for programming/evicting keyslots;
however, new functionality (hardware-wrapped keys) will require new
functions here which are unrelated to keyslots. Moreover,
device-mapper devices already (ab)use "keyslot_evict" to pass key
eviction requests to their underlying devices even though
device-mapper devices don't have any keyslots themselves (so it
really should be "evict_key", not "keyslot_evict").
- Sometimes (but not always!) it manages keyslots. Originally it
always did, but device-mapper devices don't have keyslots
themselves, so they use a "passthrough keyslot manager" which
doesn't actually manage keyslots. This hack works, but the
terminology is unnatural. Also, some hardware doesn't have keyslots
and thus also uses a "passthrough keyslot manager" (support for such
hardware is yet to be upstreamed, but it will happen eventually).
Let's stop having keyslot managers which don't actually manage keyslots.
Instead, rename blk_keyslot_manager to blk_crypto_profile.
This is a fairly big change, since for consistency it also has to update
keyslot manager-related function names, variable names, and comments --
not just the actual struct name. However it's still a fairly
straightforward change, as it doesn't change any actual functionality.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20211018180453.40441-4-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for renaming struct blk_keyslot_manager to struct
blk_crypto_profile, rename the keyslot-manager.h and keyslot-manager.c
source files. Renaming these files separately before making a lot of
changes to their contents makes it easier for git to understand that
they were renamed.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20211018180453.40441-3-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The 'reg_vmmc' regulator is enabled in the probe. It is never disabled.
Neither in the error handling path of the probe nor in the remove
function.
Register a devm_action to disable it when needed.
Fixes: 4dc5a79f13 ("mmc: mxs-mmc: enable regulator for mmc slot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4aadb3c97835f7b80f00819c3d549e6130384e67.1634365151.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Configure optional wakeirq. This may be optionally configured for SDIO
dat1 pin for wake-up events for SoCs that support deeper idle states.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-7-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow powering off SDIO cards and enable runtime PM for eMMC/SD card
devices. Without this, SDIO WLAN devices will not idle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-6-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement PM runtime functions and enable autosuspend.
Note that we save context in probe to avoid restoring invalid context
on the first resume. For system suspend, we have the new PM runtime
functions do most of the work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-5-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The omap specific registers are at offset 0x100 from base for omap4 and
later, and for omap3 and earlier they are at offset 0. Let's handle also
the earlier SoCs by adding omap_offset.
Note that eventually we should just move to using standard sdhci register
access for the sdhci range with new offsets starting at 0x100.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-4-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to start deprecating the custom omap_hsmmc.c in favor of the
generic sdhci-omap driver, we need to add support for voltages for earlier
SoCs.
The PBIAS regulator on omap4 and earlier only supports nominal values of
1.8V and 3.0V, while omap5 and later support nominal values of 1.8V and
3.3V IO voltage.
This gets omap4/5 working with sdhci-omap driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20211015104720.52240-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.
Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.
Fixes: d9370424c9 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no user of this member. Remove the dead code for good.
The removal is dependent on the previous removal of the
struct sdhci_pci_data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last user of this struct gone couple of releases ago.
Remove the dead code for good and encourage people to use
MMC core functionality for that.
The removal is dependent on the previous removal of the
struct sdhci_pci_data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last user of this struct gone a couple of releases ago.
Besides that there were not so many users of this API for
more than 10 years:
1/ The one is Intel Merrifield, that had been added 2016-08-31
by the commit 3976b0380b ("x86/platform/intel-mid: Enable
SD card detection on Merrifield") and removed 2021-02-11 by
the commit 4590d98f5a ("sfi: Remove framework for deprecated
firmware").
2/ The other is Intel Sunrisepoint related, that had been added
2015-02-06 by the commit e1bfad6d93 ("mmc: sdhci-pci: Add
support for drive strength selection for SPT") and removed
2017-03-20 by the commit 51ced59cc0 ("mmc: sdhci-pci: Use
ACPI DSM to get driver strength for some Intel devices").
Effectively this is a revert of the commit 52c506f0bc ("mmc:
sdhci-pci: add platform data").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The analogue of the sdhci_get_cd_nogpio() is used in the sdhci-pci-core
and sdhci-acpi modules. Deduplicate it by moving to sdhci and exporting.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211014132613.27861-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct request is only used by blk-mq drivers, so move it and all
related declarations to blk-mq.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-18-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are several error return paths that dereference the null pointer
host because the pointer has not yet been set to a valid value.
Fix this by adding a new out_mmc label and exiting via this label
to avoid the host clean up and hence the null pointer dereference.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 8105c2abbf ("mmc: moxart: Fix reference count leaks in moxart_probe")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211013100052.125461-1-colin.king@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Merrifield platform had been converted to use ACPI enumeration.
However, the driver missed an update to retrieve card detect GPIO.
Fix it here.
Unfortunately we can't rely on CD GPIO state because there are two
different PCB designs in the wild that are using the opposite card
detection sense and there is no way to distinguish those platforms,
that's why ignore CD GPIO completely and use it only as an event.
Fixes: 4590d98f5a ("sfi: Remove framework for deprecated firmware")
BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211013201723.52212-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
