Use the same pm_ops for all system suspend and resume paths. This isn't
ideal for suspend to disk with older CODECs as we'll suspend and then
resume the CODEC before powering off all of which takes a long time due
to VMID ramps but it's very simple to implement and for modern CODECs the
overhead should be minimal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The runtime PM core no longer requires any callbacks so don't provide
empty ones for it any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Mute Switch should be called Playback Switch to match the volume
and the regmap core has been updated so we don't need to mark all the
registers as non-volatile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix silent output on Haier W18 laptop
ALSA: hda: set mute led polarity for laptops with buggy BIOS based on SSID
ALSA: hda - Fix silent output on ASUS A6Rp
ALSA: Fix memory leak on error in snd_compr_set_params()
ALSA: ymfpci - Don't create invalid PCM & mixers when AC97 doesn't support
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator has no power control itself and so shouldn't cause a
power up of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't really care if any action is taken immediately so let the PM
core defer things if it wants to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modern devices allow systems to enable and disable individual supplies on
the device, allowing additional power saving by switching off regulators
which power portions of the device which are not currently in use. Add a
new SND_SOC_DAPM_REGULATOR_SUPPLY widget type factoring out the code for
managing such widgets from individual drivers.
The widget name will be used as the supply name when requesting the
regulator from the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The very same problem is seen on Haier W18 laptop with ALC861 as seen
on ASUS A6Rp, which was fixed by the commit 3b25eb69.
Now we just need to add a new SSID entry pointing to the same fixup.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42656
Cc: <stable@kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm2000: Fix use-after-free - don't release_firmware() twice on error
ASoC: wm8958: Use correct format string in dev_err() call
ASoC: wm8996: Call _POST_PMU callback for CPVDD
ASoC: mxs: Fix mxs-saif timeout
ASoC: Disable register synchronisation for low frequency WM8996 SYSCLK
ASoC: Don't go through cache when applying WM5100 rev A updates
ASoC: Mark WM5100 register map cache only when going into BIAS_OFF
ASoC: tlv320aic32x4: always enable analouge block
ASoC: tlv320aic32x4: always enable dividers
ASoC: sgtl5000: Fix wrong register name in restore
As per discussion we can safely ignore the 8 and 16 bit sample
sizes when applying the msbits constraint.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
HP laptop models with buggy BIOS are apparently frequent, including
machines with different codecs. Set the polarity of the mute led based
on the SSID and include an entry for the HP Mini 110-3100.
Signed-off-by: Gustavo Maciel Dias Vieira <gustavo@sagui.org>
Tested-by: Predrag Ivanovic <predivan@open.telekom.rs>
Cc: <stable@kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The refactoring of Realtek codec driver in 3.2 kernel caused a
regression for ASUS A6Rp laptop; it doesn't give any output.
The reason was that this machine has a secret master mute (or EAPD)
control via NID 0x0f VREF. Setting VREF50 on this node makes the
sound working again.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42588
Cc: <stable@kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If copy_from_user() does not return 0 we'll leak the memory we
allocated for 'params' when that variable goes out of scope.
Also a small CodingStyle cleanup: Use braces on both branches of
if/else when one branch needs it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- check SDAC bit of AC97 primary codec when create "rear" device 3,
"4ch" device 2 and "4ch Duplication" switch as the card need a four channels
AC97 codec to support surround40.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In wm2000_i2c_probe(), if we take the true branch in
"
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000,
NULL, 0);
if (ret != 0)
goto err_fw;
"
then we'll release_firmware(fw) at the 'err_fw' label. But we've already
done that just a few lines above. That's a use-after-free bug.
This patch restructures the code so that we always call
release_firmware(fw) before leaving the function, but only ever call
it once.
This means that we have to initialize 'fw' to NULL since some paths
may now end up calling it without having called request_firmware(),
but since request_firmware() deals gracefully with NULL pointers, we
are fine if we just NULL initialize it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To print a value of type size_t one should use %zd, not %d.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The recent change of the power-widget handling for IDT codecs caused
the silent output from the docking-station line-out jack. This was
partially fixed by the commit f2cbba7602
"ALSA: hda - Fix the lost power-setup of seconary pins after PM resume".
But the line-out on the docking-station is still silent when booted
with the jack plugged even by this fix.
The remainig bug is that the power-widget is set off in stac92xx_init()
because the pins in cfg->line_out_pins[] aren't checked there properly
but only hp_pins[] are checked in is_nid_hp_pin().
This patch fixes the problem by checking both HP and line-out pins
and leaving the power-map correctly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42637
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The user reports that model=auto works fine for him. Using
model=auto bring in new features such as jack detection notification
to userspace.
Alsa info is available at http://paste.ubuntu.com/805351/
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 2ae66c2655
ALSA: hda: option to enable arbitrary buffer/period sizes
introduced a regression on machines with Intel controller and Nvidia
HDMI. The reason is that the driver modifies the global variable
align_buffer_size when an Intel controller is found, and the Nvidia
HDMI controller is probed after Intel although Nvidia chips require
the aligned buffers.
This patch fixes the problem by moving the flag into the local struct
so that it's not affected by other controllers.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42567
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix below build warning when CONFIG_HOTPLUG is not set.
CC sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
CC sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to table based DAPM and control init.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be allowing a 5ms delay after the charge pump is started in
order to ensure it has finished ramping.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Visstrim_M10 has an external class D amplifier.
This patch provides support for controlling the 4
possible gain levels and per channel muting.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On a mx28evk board the following errors happens on mxs-sgtl5000 probe:
[ 0.660000] saif0_clk_set_rate: divider writing timeout
[ 0.670000] mxs-sgtl5000: probe of mxs-sgtl5000.0 failed with error -110
[ 0.670000] ALSA device list:
[ 0.680000] No soundcards found.
This timeout happens because clk_set_rate will result in writing to the DIV bits
of register HW_CLKCTRL_SAIF0 with the saif clock gated (CLKGATE bit set to one).
MX28 Reference states the following about CLKGATE:
"The DIV field can change ONLY when this clock gate bit field is low."
So call clk_prepare_enable prior to clk_set_rate to fix this problem.
After this change the mxs-saif driver can be correctly probed and audio is functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more what the device model wants us to do and will allow use by
non-audio functions before the audio part of the device has come up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow us to move the interrupt allocation out of the ASoC part
of the driver and simplifies the locking by removing any reliance in the
bulk of the interrupt path on the big CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McPDM internal FIFO is 24 bit wide. From the 32 bit sample
8 bit is discarded. Let application know about this
via msbits constraint.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Throughout the sgtl5000 driver source code and also in the sgtl5000 datasheet
the revision code is shown in hexadecimal.
Print it hex format, for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If an interrupt is supplied then use it for thermal warning and FLL lock
notifications. When using the interrupt raise the timeout for the FLL lock
substantially to reduce the chances of spurious warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most devices accept data in formats that don't correspond directly to
their internal format. ALSA allows us to set a msbits constraint which
tells userspace about this in case it finds it useful (for example, in
order to avoid wasting effort dithering bits that will be ignored when
raising the sample size of data) so provide a mechanism for drivers to
specify the number of bits that are actually significant on a DAI and
add the appropriate constraints along with all the others.
This is done slightly awkwardly as the constraint is specified per sample
size - we loop over every possible sample size, including ones that the
device doesn't support and including ones that have fewer bits than are
actually used, but this is harmless as the upper layers do the right thing
in these cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This must be a leftover from a previous driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Much more compact, both in terms of source and especially in terms of
RAM used at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Visstrim_M10 board uses an external microphone
that can be enabled/disabled by the user
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both the Snapper CL15 and EDB93xx audio drivers set the same audio
configuration in ep93xx_i2s_acquire. Remove the arguments to
ep93xx_i2s_acquire so that the audio drivers no longer need the
EP93XX_SYSCON defines exported.
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
remove unnecessary inclusion of machine specific header
file mach/dm365.h from cq93vc.c voice codec driver
which comes in the way of platform code consolidation.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is useful to create dummy codec devices where we need to have some
DAI links without a real Codec. e.g. could be used to represent dumb FM,
MODEM, etc
This is also used by dynamic PCM for DAI links that have no codec.
Signed-off-by: Liam Girdwood <lrg@ti.com>
[Fixed the indentation -- broonie]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a method for mach drivers to query the HS DC offset step size in mV.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Print out the offending DAI link entry when a naming error occurs. Makes
thing easier to debug for machines with a large number of DAI links.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The register map for this device is actually fairly sparse so the rbtree
should be beneficial.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
