LightNVM used to be managed and configured through sysfs. Since the
introduction of management ioctls this interface is redundant and
outdated. Get rid of it.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
rrpc cannot handle bios of size > 256kb due to NVMe using a 64 bit
bitmap to signal I/O completion. If a larger bio comes, split it
explicitly.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Bad blocks should be managed by block owners. This would be either
targets for data blocks or sysblk for system blocks.
In order to support this, export two functions: One to mark a block as
an specific type (e.g., bad block) and another to update the bad block
table on the device.
Move bad block management to rrpc.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Device blocks should be marked by the device and considered as bad
blocks by the media manager. Thus, do not make assumptions on which
blocks are going to be used by the device. In doing so we might lose
valid blocks from the free list.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Erases might be subject to host hints. An example is multi-plane
programming to erase blocks in parallel. Enable targets to specify this
hint.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Previously, LBA read and write were not supported in the lightnvm
specification. Now that it supports it, lets use the traditional
NVMe gendisk, and attach the lightnvm sysfs geometry export.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block layer updates from Jens Axboe:
"This is the main pull request for block layer changes in 4.9.
As mentioned at the last merge window, I've changed things up and now
do just one branch for core block layer changes, and driver changes.
This avoids dependencies between the two branches. Outside of this
main pull request, there are two topical branches coming as well.
This pull request contains:
- A set of fixes, and a conversion to blk-mq, of nbd. From Josef.
- Set of fixes and updates for lightnvm from Matias, Simon, and Arnd.
Followup dependency fix from Geert.
- General fixes from Bart, Baoyou, Guoqing, and Linus W.
- CFQ async write starvation fix from Glauber.
- Add supprot for delayed kick of the requeue list, from Mike.
- Pull out the scalable bitmap code from blk-mq-tag.c and make it
generally available under the name of sbitmap. Only blk-mq-tag uses
it for now, but the blk-mq scheduling bits will use it as well.
From Omar.
- bdev thaw error progagation from Pierre.
- Improve the blk polling statistics, and allow the user to clear
them. From Stephen.
- Set of minor cleanups from Christoph in block/blk-mq.
- Set of cleanups and optimizations from me for block/blk-mq.
- Various nvme/nvmet/nvmeof fixes from the various folks"
* 'for-4.9/block' of git://git.kernel.dk/linux-block: (54 commits)
fs/block_dev.c: return the right error in thaw_bdev()
nvme: Pass pointers, not dma addresses, to nvme_get/set_features()
nvme/scsi: Remove power management support
nvmet: Make dsm number of ranges zero based
nvmet: Use direct IO for writes
admin-cmd: Added smart-log command support.
nvme-fabrics: Add host_traddr options field to host infrastructure
nvme-fabrics: revise host transport option descriptions
nvme-fabrics: rework nvmf_get_address() for variable options
nbd: use BLK_MQ_F_BLOCKING
blkcg: Annotate blkg_hint correctly
cfq: fix starvation of asynchronous writes
blk-mq: add flag for drivers wanting blocking ->queue_rq()
blk-mq: remove non-blocking pass in blk_mq_map_request
blk-mq: get rid of manual run of queue with __blk_mq_run_hw_queue()
block: export bio_free_pages to other modules
lightnvm: propagate device_add() error code
lightnvm: expose device geometry through sysfs
lightnvm: control life of nvm_dev in driver
blk-mq: register device instead of disk
...
device_add() may fail, and all callers are supposed to check the
return value, but one new user in lightnvm doesn't:
drivers/lightnvm/sysfs.c: In function 'nvm_sysfs_register_dev':
drivers/lightnvm/sysfs.c:184:2: error: ignoring return value of 'device_add',
declared with attribute warn_unused_result [-Werror=unused-result]
This changes the caller to propagate any error codes, which avoids
the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 38c9e260b9f9 ("lightnvm: expose device geometry through sysfs")
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
For a host to access an Open-Channel SSD, it has to know its geometry,
so that it writes and reads at the appropriate device bounds.
Currently, the geometry information is kept within the kernel, and not
exported to user-space for consumption. This patch exposes the
configuration through sysfs and enables user-space libraries, such as
liblightnvm, to use the sysfs implementation to get the geometry of an
Open-Channel SSD.
The sysfs entries are stored within the device hierarchy, and can be
found using the "lightnvm" device type.
An example configuration looks like this:
/sys/class/nvme/
└── nvme0n1
├── capabilities: 3
├── device_mode: 1
├── erase_max: 1000000
├── erase_typ: 1000000
├── flash_media_type: 0
├── media_capabilities: 0x00000001
├── media_type: 0
├── multiplane: 0x00010101
├── num_blocks: 1022
├── num_channels: 1
├── num_luns: 4
├── num_pages: 64
├── num_planes: 1
├── page_size: 4096
├── prog_max: 100000
├── prog_typ: 100000
├── read_max: 10000
├── read_typ: 10000
├── sector_oob_size: 0
├── sector_size: 4096
├── media_manager: gennvm
├── ppa_format: 0x380830082808001010102008
├── vendor_opcode: 0
├── max_phys_secs: 64
└── version: 1
Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
LightNVM compatible device drivers does not have a method to expose
LightNVM specific sysfs entries.
To enable LightNVM sysfs entries to be exposed, lightnvm device
drivers require a struct device to attach it to. To allow both the
actual device driver and lightnvm sysfs entries to coexist, the device
driver tracks the lifetime of the nvm_dev structure.
This patch refactors NVMe and null_blk to handle the lifetime of struct
nvm_dev, which eliminates the need for struct gendisk when a lightnvm
compatible device is provided.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
With LightNVM enabled namespaces, the gendisk structure is not exposed
to the user. This prevents LightNVM users from accessing the NVMe device
driver specific sysfs entries, and LightNVM namespace geometry.
Refactor the revalidation process, so that a namespace, instead of a
gendisk, is revalidated. This later allows patches to wire up the
sysfs entries up to a non-gendisk namespace.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If NO_DMA=y:
drivers/built-in.o: In function `nvme_nvm_dev_dma_free':
lightnvm.c:(.text+0x23df1a): undefined reference to `dma_pool_free'
drivers/built-in.o: In function `nvme_nvm_dev_dma_alloc':
lightnvm.c:(.text+0x23df38): undefined reference to `dma_pool_alloc'
drivers/built-in.o: In function `nvme_nvm_destroy_dma_pool':
lightnvm.c:(.text+0x23df4c): undefined reference to `dma_pool_destroy'
drivers/built-in.o: In function `nvme_nvm_create_dma_pool':
lightnvm.c:(.text+0x23df7e): undefined reference to `dma_pool_create'
and
ERROR: "dma_pool_destroy" [drivers/nvme/host/nvme-core.ko] undefined!
ERROR: "dma_pool_free" [drivers/nvme/host/nvme-core.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/nvme/host/nvme-core.ko] undefined!
ERROR: "dma_pool_create" [drivers/nvme/host/nvme-core.ko] undefined!
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch removes module_init()/module_exit() from driver code by using
module_misc_device() macro. All modules in this patch has a print
statement which is removed when module_misc_device() macro is used.
If undesirable this patch can be dropped entirely, this is the only
purpose of making this as a separate patch.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two are confusing leftover of the old world order, combining
values of the REQ_OP_ and REQ_ namespaces. For callers that don't
special case we mostly just replace bi_rw with bio_data_dir or
op_is_write, except for the few cases where a switch over the REQ_OP_
values makes more sense. Any check for READA is replaced with an
explicit check for REQ_RAHEAD. Also remove the READA alias for
REQ_RAHEAD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __nvm_submit_ppa() function is not used outside lightnvm core.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The passed by reference ppa list in nvm_set_rqd_list() is updated when
multiple planes are available. In that case, each PPA plane is
incremented when the device side PPA list is created. This prevents the
caller to rely on the PPA list to be unmodified after a call.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The gen_mark_blk_bad function marks the wrong block when a block is on
a different channel. Fix the index calculation, so that it updates the
correct block.
Reported-by: Javier Gonzalez <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvm_get_blk() function is called with rlun->lock held. This is ok
when the media manager implementation doesn't go out of its atomic
context. However, if a media manager persists its metadata, and
guarantees that the block is given to the target, this is no longer
a viable approach. Therefore, clean up the flow of rrpc_map_page,
and make sure that nvm_get_blk() is called without any locks acquired.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The [get/put]_blk API enables targets to get ownership of blocks at
runtime. This information is currently not recorded on disk, and the
information is therefore lost on power failure. To restore the
metadata, the [get/put]_blk must persist its metadata. In that case,
we need to control the outer lock, so that we can disable them while
updating the on-disk metadata. Fortunately, the _unlocked versions can
be removed, which allows us to move the lock into the [get/put]_blk
functions.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The ->list, ->open_list, and ->closed_list lists were previously used
for statistics. However, their usage have been removed, and thus these
can safely be removed.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a media manager tries to initialize it targets upon media manager
initialization, the media manager will need to know which target types
are available in LightNVM. The lists of which managers and target types
are available shares the same lock.
Therefore, on initialization, the nvm_lock is taken by LightNVM core,
which later leads to a deadlock when target types are enumerated by the
media manager.
Add an exclusive lock for target types to resolve this conflict.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
To enable persistent block management to easily control creation and
removal of targets, we move target management into the media
manager. The LightNVM core continues to maintain which target types are
registered, while the media manager now keeps track of its initialized
targets.
Two new callbacks for the media manager are introduced. create_tgt and
remove_tgt. Note that remove_tgt returns 0 on successfully removing a
target, and returns 1 if the target was not found.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The generic manager should be called the general media manager, and
instead of using the rather long name of "gennvm" in front of each data
structures, use "gen" instead to shorten it. Update the description of
the media manager as well to make the media manager purpose clearer.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The responsibility of the media manager is not to keep track of
open/closed blocks. This is better maintained within a target,
that already manages this information on writes.
Remove the statistics and merge the states NVM_BLK_ST_OPEN and
NVM_BLK_ST_CLOSED.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A couple of small checkpatch fixups to stop it from complaining.
./drivers/lightnvm/core.c:360: WARNING: line over 80 characters
./drivers/lightnvm/core.c:360: ERROR: trailing statements should be on
next line
./drivers/lightnvm/core.c:503: WARNING: Block comments use a trailing */
on a separate line
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Checkpatch found two incidents where the type was preferred to be
written out in full.
./drivers/lightnvm/rrpc.h:184: WARNING: Prefer 'unsigned int' to bare
use of 'unsigned'
./drivers/lightnvm/rrpc.h:209: WARNING: Prefer 'unsigned int' to bare
use of 'unsigned'
./drivers/lightnvm/rrpc.c:51: WARNING: Prefer 'unsigned int' to bare use
of 'unsigned'
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Mark functions not used by ouside of thier implementing file as static.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Expose media manager mark_blk() to targets, as done for the rest of the
media manager callback functions.
Signed-off-by: Javier González <javier@cnexlabs.com>
Updated description
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Break the loop when rqd is not null to reduce
an unnecessary schedule.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The nvm_dev->max_pages_per_blk variable was removed in favor of the new
nvm->sec_per_blk variable. The ->max_pages_per_blk variable was still
used in rrpc_capacity, reporting the reserved capacity to zero. Replace
with ->sec_per_blk to calculate the reserved area again.
Signed-off-by: Javier González <javier@cnexlabs.com>
Updated patch description. Was "lightnvm: eliminate redundant variable"
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The number of ppas contained on a request is not necessarily the number
of pages that it maps to neither on the target nor on the device side.
In order to avoid confusion, rename nr_pages to nr_ppas since it is what
the variable actually contains.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Targets can update a block state when having a reference to an
in-memory virtual block. In the case that a target does not keep the
block metadata in memory, it does not have a way to update this
structure.
Therefore, expose gennvm_mark_blk() through the media managers
->mark_blk() callback and let targets update the state structure through
this callback.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Targets associated with a device manager are not freed on device
removal. They have to be manually removed before shutdown. Make sure
any outstanding targets are freed upon shutdown.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
When doing GC, rrpc calculates the physical LUN to which the rrpc block
belongs too. This calculation is based on the assumption that LUNs are
assigned sequentially to the LUN list. Use the reference to the LUN
instead. This saves us the calculation and allows us to align LUNs in a
different manner to, for example, take advantage of devide parallelism.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Until now, the dma pool have been exclusively used to allocate the ppa
list being sent to the device. In pblk (upcoming), we use these pools to
allocate metadata too. Thus, we generalize the names of some variables
on the dma helper functions to make the code more readable.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
rrpc does not save any metadata on a given request. Thus, do not attempt
to free the metadata dma region.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The ppa configured for retrieving the bad block table uses the internal
lun id to setup the get bad block ppa. This increases monotonically
with the number luns available. When configuring a ppa, the channel and
lun must be specified separately, leading to an out of bound memory
access in gennvm_block_bb when lun id goes beyond the luns available
within a channel.
Additional, remove out of bound check in gennvm_block_bb(), as it was a
buggy to begin with.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The set_bb_tbl takes struct nvm_rq and only uses its ppa_list and
nr_pages internally. Instead, make these two variables explicit.
This allows a user to call it without initializing a struct nvm_rq
first.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
We move the responsibility of managing the persistent bad block table to
the target. The target may choose to mark a block bad or retry writing
to it. Never the less, it should be the target that makes the decision
and not the media manager.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A virtual block enables a block to identify multiple physical blocks.
This is useful for metadata where a device media supports multiple
planes. In that case, a block, with multiple planes can be managed
as a single vblk. Reducing the metadata required by one forth.
nvm_set_rqd_ppalist() takes care of expanding a ppa_list with vblks
automatically. However, for some use-cases, where only a single physical
block is required, the ppa_list should not be expanded.
Therefore, add a vblk parameter to nvm_set_rqd_ppalist(), and only
expand the ppa_list if vblk is set.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that device ops->get_bb_table no longer uses a callback, the
struct factory_blks can be removed.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The device ops->get_bb_tbl() takes a callback, that allows the caller
to use its own callback function to update its data structures in the
returning function.
This makes it difficult to send parameters to the callback, and usually
is circumvented by small private structures, that both carry the callers
state and any flags needed to fulfill the update.
Refactor ops->get_bb_tbl() to fill a data buffer with the status of the
blocks returned, and let the user call the callback function manually.
That will provide the necessary flags and data structures and simplify
the logic around ops->get_bb_tbl().
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Users that wish to iterate all luns on a device. Must create a
struct ppa_addr and separate iterators for channels and luns. To set the
iterators, two loops are required, one to iterate channels, and another
to iterate luns. This leads to decrease in readability.
Introduce nvm_for_each_lun_ppa, which implements the nested loop and
sets ppa, channel, and lun variable for each loop body, eliminating
the boilerplate code.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A target name must be unique. However, a per-device registration of
targets is maintained on a dev->online_targets list, with a per-device
search for targets upon registration.
This results in a name collision when two targets, with the same name,
are created on two different targets, where the per-device list is not
shared.
Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The functions nvm_register_target(), nvm_unregister_target() and
associated list refers to a target type that is being registered by a
target type module. Rename nvm_*_targets() to nvm_*_tgt_type(), so that
the intension is clear.
This enables target instances to use the _nvm_*_targets() naming.
Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since we mainly use soffset in device sector size, we therefore store
this value in rrpc->soffset, instead of the offset in 512byte sector
size. This eliminates the "(ilog2(dev->sec_size) - 9)" calculation on
each I/O.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Updated patch description.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Calculate rrpc total blocks and sectors up front, make sense
to use them. For example, we use rrpc->nr_sects to calculate rrpc
area size, but it makes no sense if we don't initialize it up front,
since it would be zero until we finish rrpc luns init.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A memory leak occurs if the lower page table is initialized and the
following dev->lun_map fails on allocation.
Rearrange the initialization of lower page table to allow dev->lun_map
to fail gracefully without memory leak.
Reviewed by: Johannes Thumshirn <jthumshirn@suse.de>
Move kfree of dev->lun_map to nvm_free()
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The get block table command returns a list of blocks and planes
with their associated state. Users, such as gennvm and sysblk,
manages all planes as a single virtual block.
It was therefore natural to fold the bad block list before it is
returned. However, to allow users, which manages on a per-plane
block level, to also use the interface, the get_bb_tbl interface is
changed to not fold by default and instead let the caller fold if
necessary.
Reviewed by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
