The ADV748X_PAGE_WAIT is a fake page to insert arbitrary delays in the
register tables.
Its only usage was removed, so we can remove the handling and simplify
the code.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x is currently reset by writting a small table of registers to
the device.
The table lacks documentation and contains magic values to perform the
actions, including using a fake register address to introduce a delay
loop.
Remove the table, and convert to code, documenting the purpose of the
specific writes along the way.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the adv748x driver is informed about a link being created from HDMI or
AFE to a CSI-2 TX output, the 'link_setup()' callback is invoked. Make
sure to implement proper routing management at link setup time, to route
the selected video stream to the desired TX output.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The power_up_tx() procedure needs to set a few registers conditionally to
the selected video source, but it currently checks for the provided tx to
be either TXA or TXB.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, checking which TX the function is operating on is not meaningful anymore.
To fix this, store the subdevice of the source providing video data to the
CSI-2 TX in the 'struct adv748x_csi2' representing the TX and check on it.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch to devm_kzalloc() when allocating the adv748x device struct.
The sizeof() is updated to determine the correct allocation size from
the dereferenced pointer type rather than hardcoding the struct type.
[Kieran: Change sizeof() to dereference the pointer type]
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver fixed the TXA CSI-2 transmitter in 4-lane mode while it could
operate using 1-, 2- and 4-lanes. Update the driver to support all
available modes.
The driver makes use of large tables of static register/value writes
when powering up/down the TXA and TXB transmitters which include the
write to the NUM_LANES register. By converting the tables into functions
and using parameters the power up/down functions for TXA and TXB power
up/down can be merged and used for both transmitters.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The adv748x CSI-2 transmitters TXA and TXB can use different number of
lanes to transmit data. In order to be able to configure the device
correctly this information need to be parsed from device tree and stored
in each TX private data structure.
TXA supports 1, 2 and 4 lanes while TXB supports 1 lane.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend the MIPI CSI-2 power up sequence to match the power up sequence
in the hardware manual chapter "9.5.1 Power Up Sequence". This change
allows the power up functions to be reused when initializing the
hardware reducing code duplicating as well aligning with the
documentation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x has two CSI-2 output port and one TTL input/output port for
digital video reception/transmission. The TTL digital pad is unconditionally
enabled during the device reset even if not used. Same goes for the TXA
and TXB CSI-2 outputs, which are enabled by the initial settings blob
programmed into the chip.
In order to improve power saving, do not enable unused output interfaces:
keep TTL output disabled, as it is not used, and drop CSI-2 output enabling
from the initial settings list, as they get conditionally enabled later.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the driver is now allowed to probe with a single output endpoint,
power management routines shall now take into account the case a CSI-2 TX
is not enabled.
Unify the adv748x_tx_power() routine to handle transparently TXA and TXB,
and enable the CSI-2 outputs conditionally.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the adv748x driver will fail to probe unless both of its
output endpoints (TXA and TXB) are connected.
Make the driver support probing provided that there is at least one
input, and one output connected and protect the clean-up function from
accessing un-initialized fields.
Following patches will fix other uses of un-initialized TXs in the driver,
such as power management functions.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As original license mentioned, it is GPL-2.0+ in SPDX.
Then, MODULE_LICENSE() should be "GPL" instead of "GPL v2".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has identical map configurations for each register map. The
duplication of each map can be simplified using a helper macro such that
each map is represented on a single line.
Define ADV748X_REGMAP_CONF for this purpose use it to create the tables.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error handling for the adv748x_identify_chip() call erroneously
jumps to the err_cleanup_clients label before the clients have been
established.
Correct this by jumping to the next (and correct) label in the cleanup
code: err_cleanup_dt.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of_node_full_name() now returns only the basename, the endpoint
information printed became useless:
adv748x 4-0070: Endpoint endpoint on port 7
adv748x 4-0070: Endpoint endpoint on port 8
adv748x 4-0070: Endpoint endpoint on port 10
adv748x 4-0070: Endpoint endpoint on port 11
Restore the old behavior by using "%pOF" instead:
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11
Fixes: a7e4cfb0a7 ("of/fdt: only store the device node basename in full_name")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, and the driver is only exporting the OF ID
table entries as module aliases.
So if the driver is built as module, autoload won't work since udev/kmod
won't be able to match the registered OF device with its driver module.
Before this patch:
$ modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
After this patch:
modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
alias: i2c:adv7482
alias: i2c:adv7481
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide support for the ADV7481 and ADV7482.
The driver is modelled with 4 subdevices to allow simultaneous streaming
from the AFE (Analog front end) and HDMI inputs though two CSI TX
entities.
The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked
to the TXB CSI bus.
The driver is based on a prototype by Koji Matsuoka in the Renesas BSP,
and an earlier rework by Niklas Söderlund.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
