The edp-phy control is a part of the General Register Files and
with a recent patch in 4.6 the phy driver can now also handle this
correctly, so move the dts node under the GRF as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Similar to the pmu, the general register files contain a lot of different
setting bits grouped into general registers, but also some somewhat special
entities like the controls for some phy-blocks or the io-voltage control.
To be able to move these blocks under the grf node where they actually
belong, make it a simple-mfd.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The edp hotplug pin is fixed on the soc side, anybody wanting to use it
will need the same definition anyway, so move it to a common location.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Add the rk3288 edp node and its hooks into the display-subsystem.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Add the core device node of the edp-phy on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
The mipi controller node does contain an unused reg property as well as
unnecessary #address-cells and #size-cells properties for subnodes
not using addresses, so remove those to also make dtc happy.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
The usbphy subnodes do have a reg property but no unitname, add them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
The power-domain sub-nodes do have reg properties, but so far are
missing the expected unit names. So add the missing ones.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
The MIPI controllers are part of the VIO power domain so add the
necessary property to indicate this for the controller we support.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These must be translated from the values in the TRM by subtracting 32,
which has not been done. The SPDIF interrupt is also off-by-one.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This isn't currently used by the driver but the correct value is 19
since DSIHOST0 is 51 in the TRM and the GIC offset requires 32 to be
subtracted.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The compatible string "simple-bus" is well defined in ePAPR, while
I see no documentation for the "arm,amba-bus" arnywhere in ePAPR or
Documentation/devicetree/.
DT is also used by other projects than Linux kernel. It is not a
good idea to rely on such an unofficial binding.
This commit
- replaces "arm,amba-bus" with "simple-bus"
- drops "arm,amba-bus" where it is used along with "simple-bus"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pl330 integrated in rk3288 platform doesn't support
DMAFLUSHP function. So we add arm,pl330-broken-no-flushp quirk
for it.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the #clock-cells properties for the usbphy nodes as they
provide the pll-clocks now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The EDP 24M clock can be fed either by an SoC internal fixed clock or
from an external IC. Change the default parent to the internal clock in
the main rk3288 dtsi, to ensure (by default) it gets setup with a
non-orphaned clock (hardware defaults to the externa clock).
This prevents potential issues when the clock framework get support for
deferring on orphaned clocks, while specific boards can always change
the parent clock if an external input is preferred.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a mipi_dsi node, and also add mipi_dsi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
support for the efuses on Rockchip socs and some improvements for
rk3288 regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWd0xyAAoJEPOmecmc0R2B71UIAJu6jDdfk5kmYzyXjBloBNwd
PVRojGzVjCwCiVKX7GWINSf3D7dTKeYUwVs9uouVW4Q/iIk/l4Iq46+yg20ZODNM
3haS2hwztRPEKeU+0qhYdoJf2cWOKzk0RP90umTMMVt2xnqbQCBFAW4NuE4DBLHe
5o7R99ORKHi+IjBaI6Wtk1JoRNNkyYIDW6eLC9mxAJs32mr1ee45uidhPBD+VX+n
1nf/yUPs6bc1yPyNhFN49AywYvjg02y96/4ER6bBtOcEw91uDc0ld0M10H/mvujT
B+w8U6xBUWulUU53MS8aVKDZ+bp4o6YZZbIq/FJtaz3c+bhj8Rjl4UnlZh+gaiA=
=Zp6y
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Another new soc - the rk3228 quad-core cortex-a7, a new rk3036 board,
support for the efuses on Rockchip socs and some improvements for
rk3288 regulators.
* tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the kylin board for rk3036
ARM: dts: rockchip: add the sdio/sdmmc node for rk3036
ARM: dts: rockchip: fix the pinctrl bias settings for rk3036
ARM: dts: rockchip: add eFuse node for rk3188 SoCs
ARM: dts: rockchip: add eFuse node for rk3066a SoCs
ARM: dts: rockchip: add eFuse config of rk3288 SoC
ARM: dts: rockchip: add rk3228-evb board
ARM: dts: rockchip: add core rk3228 dtsi
clk: rockchip: Add the clock ids of rk3288 eFuses
ARM: dts: rockchip: Fix typo in rk3288 sdmmc card detect pin name
ARM: dts: rockchip: fix voltage ranges for rk3288-evb-act8846 board
ARM: dts: rockchip: move the public part to rk3288-evb common
ARM: dts: rockchip: add 2 regulators for rk3288-evb-act8846
ARM: dts: rockchip: correct the name of REG8 for rk3288-evb-act8846
clk: rockchip: add dt-binding header for rk3228
clk: rockchip: add id for mipidsi sclk on rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Among the bigger changes are two new Veyron boards, support for
the dual-core cortex-a7 rk3036 soc and addition of support for
the crypto engine of the rk3288. Smaller changes include some
IR receivers, updates of thermal settings more reflecting real-
life and testing-results.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWYetUAAoJEPOmecmc0R2B4goIAIiVjdbuetKLxeEqDWmEdCnI
AKlV+IM1CWt8ib2k5bCoaYmWwtujY6m/2oHhbJklHgv3+K32lltwgZMJPeJu7xi3
C02HCdq6DydsCb2154giKOXj+SMsNZ/c38Gk1sDFFPQCcwfgT9Hg+7HOXCim2Ac8
C/Ewi7z6bZKzkvwy28KrQVPDub2DB/JQAGp8DP9hfK9k23PtaQRoLhTExj68O6JK
rRjB67hb1+xdKgf8ujXevIYvoacO1odW4fLnB7KC4ei/O2XycKK/4ohzrENe/zJ6
Y2wYnb1YGiLtjgx0DlpbPvaCE6/UyX+ZhVC4kUiB937/x1ZpCZX9ttLMT91gKx8=
=F0Xt
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "rockchip dts32 changes for 4.5" from Heiko Stuebner:
First round of arm devicetree changes.
Among the bigger changes are two new Veyron boards, support for
the dual-core cortex-a7 rk3036 soc and addition of support for
the crypto engine of the rk3288. Smaller changes include some
IR receivers, updates of thermal settings more reflecting real-
life and testing-results.
* tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add gpio-ir-receiver to the R89 board
ARM: dts: rockchip: add touchscreen node to veyron minnie
ARM: dts: rockchip: add veyron-mickey board
ARM: dts: rockchip: add veyron-brain board
ARM: dts: rockchip: make sure edp_24m is associated to xin24m on veyron
ARM: dts: rockchip: override thermal settings on veyron-speedy
ARM: dts: rockchip: update the thermal management on rk3288
ARM: dts: rockchip: Add Crypto node for rk3288
ARM: dts: rockchip: add rk3036-evb board
ARM: dts: rockchip: add core rk3036 dtsi
clk: rockchip: add dt-binding header for rk3036
clk: rockchip: add an id for rk3288 crypto clk
ARM: dts: rockchip: Add IR receiver to RK3288 Radxa Rock 2 Square
ARM: dts: rockchip: add channels properties for i2s
ARM: dts: rockchip: set system-power-controller property on rk3288-rock2
ARM: dts: rockchip: Setup rk3066/rk3188 ethernet0 alias for u-boot
ARM: dts: rockchip: Setup rk3288 ethernet0 alias for u-boot
The card detect pin is currently called sdmcc-cd.
This patch fixes the typo and renames the pin to sdmmc-cd.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an ethernet0 alias for the RK3288 mac interface so
that u-boot can find the device-node and fill in the mac address on
boards that support a wired network interface.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the "init" anf "sleep" pinctrl as the OTP gpio state.
We need the OTP pin is gpio state before resetting the TSADC controller,
since the tshut polarity will generate a high signal.
"init" pinctrl property is defined by Doug's Patch[0].
Patch[0]:
https://patchwork.kernel.org/patch/7454311/
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
The drive/sample clocks can be phase shifted. The drive clock
could be used in a future patch to adjust hold times. The sample
clock is used for tuning.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We can add more domains node in the future.
This patch add the needed clocks into power-controller.
As the discuess about all the device clocks being listed in
the power-domains itself.
There are several reasons as follows:
Firstly, the clocks need be turned off to save power when
the system enter the suspend state. So we need to enumerate
the clocks in the dts. In order to power domain can turn on and off.
Secondly, the reset-circuit should reset be synchronous on RK3288,
then sync revoked. So we need to enable clocks of all devices.
In other words, we have to enable the clocks before you operate them
if all the device clocks are included in someone domians.
Thirdly, as the chip designs for PM hardhare. we need turn on the noc
clocks, if we are operating the "pd_vio" domain to enter the idle status.
The device's clock be included in domains that needed turn on if do that.
The clocks in the dts are needed to enable before you want to happy work.
At the moment, This patch is very good work for PM hardware.
Also, we can add these clocks in the future if we have some hidden clocks.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
[add necessary power-domain properties to keep drm subsys working]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pins for i2c5 can either be configured as "I2C5" which means that
they're controlled by the normal RK3288 I2C controller or as "EDP / HDMI
I2C". It's unclear why EDP is referenced here since apparently setting
the mux to this position enables I2C communication using the dw_hdmi
block with a patch like <https://patchwork.kernel.org/patch/7098101/>.
There appear to be some reasons why using the builtin I2C controller in
dw_hdmi is better than using the normal RK3288 I2C controller, so boards
based on rk3288 might eventually want to use this pinmux if it's known
to work.
Once driver support in dw_hdmi lands, boards would use this by selecting
this pinctrl for the HDMI block and then _not_ specifying a ddc-i2c-bus
and _not_ setting the status to "okay" for i2c5 (which uses the same
pins).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The flow control lines from a user accessible UART are optional,
the user might not have anything connected to those pins.
In order to prevent random interrupts happening and noise affecting
the cts pin should be pulled up.
Note that the default state for that pin on the rk3288 is pulled up,
so this patch merely restores them.
This is similar to what we're already doing with the RX pin,
so it should be safe. At worst it might be a slightly higher power usage
(through ~50 kohms) when the cts is low.
Suggested-by: Neil Hendin <nhendin@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The all current Rockchip SoCs supporting 4GB of ram have problems accessing
the memory region 0xfe000000~0xff000000. This also seems to includes the
rk3368 arm64 soc.
All current code handling dma memory oddities I could find, seem to involve
soc-specific code (zone-dma or so) while this issue is shared between arm32
and arm64 socs from Rockchip, which would need to have this described in
the soc devicetree on both socs.
Limiting the dma-zone alone also does not solve the issue and as the
dma-masks need to be a power-of-two in the kernel, the next lower dma-mask
brings memory usable for dma down to 2GB.
So as a stop-gap block off the affected region to prevent its use by
devices with 4GB of memory, like some recent Chromebooks.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
The rk3288 uses spi irqs for the arm-pmu on individual cpu cores, so needs
the affinity to them defined.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
The watchdog irq is actually SPI 79, which translates to the original
111 in the manual where the SPI irqs start at 32.
The current dw_wdt driver does not use the irq at all, so this issue
never surfaced. Nevertheless fix this for a time we want to use the irq.
Fixes: 2ab557b72d ("ARM: dts: rockchip: add core rk3288 dtsi")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Which fixes warning "no reset control found" by the same time
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3288.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Caesar Wang <caesar.wang@rock-chips.com>
Acked-by: Lin Huang <hl@rock-chips.com>
Acked-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Jianqun Xu<jay.xu@rock-chips.com>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Roger Chen <roger.chen@rock-chips.com>
Acked-by: Yunzhi Li <lyz@rock-chips.com>
on behalf of Rockchip
Acked-by: Eddie Cai <eddie.cai@rock-chips.com>
Add properties for dwc2 usb device controller according to
Documentation/devicetree/bindings/usb/dwc2.txt
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the dts node for the PMU with the correct PMUIRQ interrupts
for each core.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
This block should not be enabled by default or else if the kconfig is set,
it will try to load/probe even if there's no phy connected.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds a device_node for RK3288 SoC usb phy. It also
defines the phy to be used by three usb controllers: usb_host0/1
and usb_otg.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
Currently the hdmi driver is using one of the soc i2c busses for ddc probing
and while documentation always specifies i2c5 as hdmi-i2c it could very well
be any other bus as well.
Therefore this is a property of the board and should be specified there.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock property for the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
The rk3288 board uses the architected timers and these ones are shutdown when
the cpu is powered down. There is a need of a broadcast timer in this case to
ensure proper wakeup when the cpus are in sleep mode and a timer expires.
Add the timer node for the broadcast timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree nodes for rk3288 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, LVDS, etc) that attach to the
VOPs' output ports.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Stephane Marchesin <marcheu@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add gmac info in rk3288.dtsi for GMAC driver
changes since v2:
1. add drive-strength in the pinctrl settings
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add pmu sram node for suspend, add global_pwroff pinctrl.
The pmu sram is used to store the resume code.
global_pwroff is held low level at work, it would be pull to high
when entering suspend. reference this in the board DTS file since
some boards need it.
Signed-off-by: Tony Xie <xxx@rock-chips.com>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All of mmc controllers include SDMMC, SDIO0, SDIO1, and EMMC on RK3288
are limited to 150Mhz. It was mainly caused by two reasons:
- RK3288's IO pad(except DDR IO pad) is generic, which can only support
the max of 150Mhz.
- Mmc controller was designed at 150Mhz, and the pressure test by IC team
was based on this freequency point.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This will enable use of physical arch timers on rk3288, where each
core comes out of reset with a different virtual offset. Using
physical timers will help with SMP booting on coreboot and older
u-boot and should also allow suspend-resume and cpu-hotplug to work on
all firmwares.
Firmware which does initialize the cpu registers properly at boot and
cpu-hotplug can remove this property from the device tree.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
