It turned out that SIGP set-multi-threading can only be done once.
Therefore switching to a different MT level after switching to
sclp.mtid_prev in the dump case fails.
As a symptom specifying the "nosmt" parameter currently fails for
the kdump kernel and the kernel starts with multi-threading enabled.
So fix this and issue diag 308 subcode 1 call after collecting the
CPU states for the dump. Also enhance the diag308_reset() function to
be usable also with enabled lowcore protection and prefix register != 0.
After the reset it is possible to switch the MT level again. We have
to do the reset very early in order not to kill the already initialized
console. Therefore instead of kmalloc() the corresponding memblock
functions have to be used. To avoid copying the sclp cpu code into
sclp_early, we now use the simple sigp loop method for CPU detection.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SCLP interface to query, configure and deconfigure CPUs actually
operates on cores. For a machine without the multi-threading faciltiy
a CPU and a core are equivalent but starting with System z13 a core
can have multiple hardware threads, also referred to as logical CPUs.
To avoid confusion replace the word 'cpu' with 'core' in the SCLP
interface. Also replace MAX_CPU_ADDRESS with SCLP_MAX_CORES.
The core-id is an 8-bit field, the maximum thread id is in the range
0-31. The theoretical limit for the CPU address is therefore 8191.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On a (theoretical) system where the read-cpu-info SCLP command does
not work but SMT is enabled, the sigp detection loop may not find
all configured cores. The maximum CPU address needs to be shifted
with smp_cpu_mt_shift.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The REGSET_VX_LOW ELF notes should contain the lower 64 bit halfes of the
first sixteen 128 bit vector registers. Unfortunately currently we copy
the upper halfes.
Fix this and correctly copy the lower halfes.
Fixes: a62bc07392 ("s390/kdump: add support for vector extension")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some high end Intel Xeon systems report uncorrectable memory errors as a
recoverable machine check. Linux has included code for some time to
process these and just signal the affected processes (or even recover
completely if the error was in a read only page that can be replaced by
reading from disk).
But we have no recovery path for errors encountered during kernel code
execution. Except for some very specific cases were are unlikely to ever
be able to recover.
Enter memory mirroring. Actually 3rd generation of memory mirroing.
Gen1: All memory is mirrored
Pro: No s/w enabling - h/w just gets good data from other side of the
mirror
Con: Halves effective memory capacity available to OS/applications
Gen2: Partial memory mirror - just mirror memory begind some memory controllers
Pro: Keep more of the capacity
Con: Nightmare to enable. Have to choose between allocating from
mirrored memory for safety vs. NUMA local memory for performance
Gen3: Address range partial memory mirror - some mirror on each memory
controller
Pro: Can tune the amount of mirror and keep NUMA performance
Con: I have to write memory management code to implement
The current plan is just to use mirrored memory for kernel allocations.
This has been broken into two phases:
1) This patch series - find the mirrored memory, use it for boot time
allocations
2) Wade into mm/page_alloc.c and define a ZONE_MIRROR to pick up the
unused mirrored memory from mm/memblock.c and only give it out to
select kernel allocations (this is still being scoped because
page_alloc.c is scary).
This patch (of 3):
Add extra "flags" to memblock to allow selection of memory based on
attribute. No functional changes
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Xiexiuqi <xiexiuqi@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for silicon that no one owns: these are really new features for
everyone.
* ARM: several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the VFIO
integration.
* s390: Some fixes/refactorings/optimizations, plus support for
2GB pages.
* x86: 1) host and guest support for marking kvmclock as a stable
scheduler clock. 2) support for write combining. 3) support for
system management mode, needed for secure boot in guests. 4) a bunch
of cleanups required for 2+3. 5) support for virtualized performance
counters on AMD; 6) legacy PCI device assignment is deprecated and
defaults to "n" in Kconfig; VFIO replaces it. On top of this there are
also bug fixes and eager FPU context loading for FPU-heavy guests.
* Common code: Support for multiple address spaces; for now it is
used only for x86 SMM but the s390 folks also have plans.
There are some x86 conflicts, one with the rc8 pull request and
the rest with Ingo's FPU rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJViYzhAAoJEL/70l94x66Dda0H/1IepMbfEy+o849d5G71fNTs
F8Y8qUP2GZuL7T53FyFUGSBw+AX7kimu9ia4gR/PmDK+QYsdosYeEjwlsolZfTBf
sHuzNtPoJhi5o1o/ur4NGameo0WjGK8f1xyzr+U8z74QDQyQv/QYCdK/4isp4BJL
ugHNHkuROX6Zng4i7jc9rfaSRg29I3GBxQUYpMkEnD3eMYMUBWGm6Rs8pHgGAMvL
vqzntgW00WNxehTqcAkmD/Wv+txxhkvIadZnjgaxH49e9JeXeBKTIR5vtb7Hns3s
SuapZUyw+c95DIipXq4EznxxaOrjbebOeFgLCJo8+XMXZum8RZf/ob24KroYad0=
=YsAR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull first batch of KVM updates from Paolo Bonzini:
"The bulk of the changes here is for x86. And for once it's not for
silicon that no one owns: these are really new features for everyone.
Details:
- ARM:
several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the
VFIO integration.
- s390:
Some fixes/refactorings/optimizations, plus support for 2GB
pages.
- x86:
* host and guest support for marking kvmclock as a stable
scheduler clock.
* support for write combining.
* support for system management mode, needed for secure boot in
guests.
* a bunch of cleanups required for the above
* support for virtualized performance counters on AMD
* legacy PCI device assignment is deprecated and defaults to "n"
in Kconfig; VFIO replaces it
On top of this there are also bug fixes and eager FPU context
loading for FPU-heavy guests.
- Common code:
Support for multiple address spaces; for now it is used only for
x86 SMM but the s390 folks also have plans"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
KVM: s390: clear floating interrupt bitmap and parameters
KVM: x86/vPMU: Enable PMU handling for AMD PERFCTRn and EVNTSELn MSRs
KVM: x86/vPMU: Implement AMD vPMU code for KVM
KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch
KVM: x86/vPMU: introduce kvm_pmu_msr_idx_to_pmc
KVM: x86/vPMU: reorder PMU functions
KVM: x86/vPMU: whitespace and stylistic adjustments in PMU code
KVM: x86/vPMU: use the new macros to go between PMC, PMU and VCPU
KVM: x86/vPMU: introduce pmu.h header
KVM: x86/vPMU: rename a few PMU functions
KVM: MTRR: do not map huge page for non-consistent range
KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
KVM: MTRR: introduce mtrr_for_each_mem_type
KVM: MTRR: introduce fixed_mtrr_addr_* functions
KVM: MTRR: sort variable MTRRs
KVM: MTRR: introduce var_mtrr_range
KVM: MTRR: introduce fixed_mtrr_segment table
KVM: MTRR: improve kvm_mtrr_get_guest_memory_type
KVM: MTRR: do not split 64 bits MSR content
KVM: MTRR: clean up mtrr default type
...
Pull s390 updates from Martin Schwidefsky:
"Pretty boring for a merge window pull.
One change in behaviour is the patch for dasd driver, the module which
provides the diagnose discipline is now loaded automatically.
The SCLP code got a nice cleanup, a new global structure replaces a
bunch of accessor functions.
And a couple of random, small improvements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: improve handling of hotplug event 0x301
s390/setup: fix DMA_API_DEBUG warnings
s390/zcrypt: remove obsolete __constant
s390/keyboard: avoid off-by-one when using strnlen_user()
s390/sclp: pass timeout as HZ independent value
s390/mm: s/specifiation/specification/, s/an specification/a specification/
s390/sclp: Use DECLARE_BITMAP
s390/dasd: Enable automatic loading of dasd_diag_mod
s390/sclp: move sclp_facilities into "struct sclp"
s390/sclp: get rid of sclp_get_mtid() and sclp_get_mtid_max()
s390/sclp: unify basic sclp access by exposing "struct sclp"
s390/sclp: prepare smp_fill_possible_mask for global "struct sclp"
Addresses from the usable space in [_ehead, _stext] lead to false
positives in DMA_API_DEBUG code (which will complain when an address
is in [_text, _etext]).
Avoid these warnings by not using that memory in case of
CONFIG_DMA_API_DEBUG=y.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As part of addressing the "y2038 problem" for in-kernel uses,
this patch converts read_boot_clock() to read_boot_clock64()
and read_persistent_clock() to read_persistent_clock64() using
timespec64.
Rename some instances of 'timespec' to 'timespec64' in time.c and
related references
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
[jstultz: Fixed minor style and grammer tweaks
pointed out by Ingo]
Signed-off-by: John Stultz <john.stultz@linaro.org>
As all relevant sclp data is now directly accessible, let's move the
logic of these two functions to the single caller.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let's unify basic access to sclp fields by storing the data in an external
struct in asm/sclp.h.
The values can now directly be accessed by other components, so there is
no need for most accessor functions and external variables anymore.
The mtid, mtid_max and facility part will be cleaned up separately.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We need to rename sclp -> sclp_max to prepare for using the global variable
"sclp" for sclp access later in this function.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
exit_sie_sync is used to kick CPUs out of SIE and prevent reentering at
any point in time. This is used to reload the prefix pages and to
set the IBS stuff in a way that guarantees that after this function
returns we are no longer in SIE. All current users trigger KVM requests.
The request must be set before we block the CPUs to avoid races. Let's
make this implicit by adding the request into a new function
kvm_s390_sync_requests that replaces exit_sie_sync and split out
s390_vcpu_block and s390_vcpu_unblock, that can be used to keep
CPUs out of SIE independent of requests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Pull s390 updates from Martin Schwidefsky:
"The major change in this merge is the removal of the support for
31-bit kernels. Naturally 31-bit user space will continue to work via
the compat layer.
And then some cleanup, some improvements and bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
s390/smp: wait until secondaries are active & online
s390/hibernate: fix save and restore of kernel text section
s390/cacheinfo: add missing facility check
s390/syscalls: simplify syscall_get_arch()
s390/irq: enforce correct irqclass_sub_desc array size
s390: remove "64" suffix from mem64.S and swsusp_asm64.S
s390/ipl: cleanup macro usage
s390/ipl: cleanup shutdown_action attributes
s390/ipl: cleanup bin attr usage
s390/uprobes: fix address space annotation
s390: add missing arch_release_task_struct() declaration
s390: make couple of functions and variables static
s390/maccess: improve s390_kernel_write()
s390/maccess: remove potentially broken probe_kernel_write()
s390/watchdog: support for KVM hypervisors and delete pr_info messages
s390/watchdog: enable KEEPALIVE for /dev/watchdog
s390/dasd: remove setting of scheduler from driver
s390/traps: panic() instead of die() on translation exception
s390: remove test_facility(2) (== z/Architecture mode active) checks
s390/cmpxchg: simplify cmpxchg_double
...
Pull timer updates from Ingo Molnar:
"The main changes in this cycle were:
- clockevents state machine cleanups and enhancements (Viresh Kumar)
- clockevents broadcast notifier horror to state machine conversion
and related cleanups (Thomas Gleixner, Rafael J Wysocki)
- clocksource and timekeeping core updates (John Stultz)
- clocksource driver updates and fixes (Ben Dooks, Dmitry Osipenko,
Hans de Goede, Laurent Pinchart, Maxime Ripard, Xunlei Pang)
- y2038 fixes (Xunlei Pang, John Stultz)
- NMI-safe ktime_get_raw_fast() and general refactoring of the clock
code, in preparation to perf's per event clock ID support (Peter
Zijlstra)
- generic sched/clock fixes, optimizations and cleanups (Daniel
Thompson)
- clockevents cpu_down() race fix (Preeti U Murthy)"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
timers/PM: Drop unnecessary braces from tick_freeze()
timers/PM: Fix up tick_unfreeze()
timekeeping: Get rid of stale comment
clockevents: Cleanup dead cpu explicitely
clockevents: Make tick handover explicit
clockevents: Remove broadcast oneshot control leftovers
sched/idle: Use explicit broadcast oneshot control function
ARM: Tegra: Use explicit broadcast oneshot control function
ARM: OMAP: Use explicit broadcast oneshot control function
intel_idle: Use explicit broadcast oneshot control function
ACPI/idle: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast oneshot control function
x86/amd/idle, clockevents: Use explicit broadcast oneshot control functions
clockevents: Provide explicit broadcast oneshot control functions
clockevents: Remove the broadcast control leftovers
ARM: OMAP: Use explicit broadcast control function
intel_idle: Use explicit broadcast control function
cpuidle: Use explicit broadcast control function
ACPI/processor: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast control function
...
ARM/ARM64: fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390: interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS: FPU and MIPS SIMD Architecture (MSA) support. Includes some patches
from Ralf Baechle's MIPS tree.
x86: bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVJ9vmAAoJEL/70l94x66DoMEH/R3rh8IMf4jTiWRkcqohOMPX
k1+NaSY/lCKayaSgggJ2hcQenMbQoXEOdslvaA/H0oC+VfJGK+lmU6E63eMyyhjQ
Y+Px6L85NENIzDzaVu/TIWWuhil5PvIRr3VO8cvntExRoCjuekTUmNdOgCvN2ObW
wswN2qRdPIeEj2kkulbnye+9IV4G0Ne9bvsmUdOdfSSdi6ZcV43JcvrpOZT++mKj
RrKB+3gTMZYGJXMMLBwMkdl8mK1ozriD+q0mbomT04LUyGlPwYLl4pVRDBqyksD7
KsSSybaK2E4i5R80WEljgDMkNqrCgNfg6VZe4n9Y+CfAAOToNnkMJaFEi+yuqbs=
=yu2b
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First batch of KVM changes for 4.1
The most interesting bit here is irqfd/ioeventfd support for ARM and
ARM64.
Summary:
ARM/ARM64:
fixes for live migration, irqfd and ioeventfd support (enabling
vhost, too), page aging
s390:
interrupt handling rework, allowing to inject all local interrupts
via new ioctl and to get/set the full local irq state for migration
and introspection. New ioctls to access memory by virtual address,
and to get/set the guest storage keys. SIMD support.
MIPS:
FPU and MIPS SIMD Architecture (MSA) support. Includes some
patches from Ralf Baechle's MIPS tree.
x86:
bugfixes (notably for pvclock, the others are small) and cleanups.
Another small latency improvement for the TSC deadline timer"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
KVM: use slowpath for cross page cached accesses
kvm: mmu: lazy collapse small sptes into large sptes
KVM: x86: Clear CR2 on VCPU reset
KVM: x86: DR0-DR3 are not clear on reset
KVM: x86: BSP in MSR_IA32_APICBASE is writable
KVM: x86: simplify kvm_apic_map
KVM: x86: avoid logical_map when it is invalid
KVM: x86: fix mixed APIC mode broadcast
KVM: x86: use MDA for interrupt matching
kvm/ppc/mpic: drop unused IRQ_testbit
KVM: nVMX: remove unnecessary double caching of MAXPHYADDR
KVM: nVMX: checks for address bits beyond MAXPHYADDR on VM-entry
KVM: x86: cache maxphyaddr CPUID leaf in struct kvm_vcpu
KVM: vmx: pass error code with internal error #2
x86: vdso: fix pvclock races with task migration
KVM: remove kvm_read_hva and kvm_read_hva_atomic
KVM: x86: optimize delivery of TSC deadline timer interrupt
KVM: x86: extract blocking logic from __vcpu_run
kvm: x86: fix x86 eflags fixed bit
KVM: s390: migrate vcpu interrupt state
...
This is the s390 version of 875ebe940d ("powerpc/smp: Wait until secondaries
are active & online").
The race described in length within the commit message is also possible on s390
and every other architecture. So fix this race on s390 as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sebastian reported a crash caused by a jump label mismatch after resume.
This happens because we do not save the kernel text section during suspend
and therefore also do not restore it during resume, but use the kernel image
that restores the old system.
This means that after a suspend/resume cycle we lost all modifications done
to the kernel text section.
The reason for this is the pfn_is_nosave() function, which incorrectly
returns that read-only pages don't need to be saved. This is incorrect since
we mark the kernel text section read-only.
We still need to make sure to not save and restore pages contained within
NSS and DCSS segment.
To fix this add an extra case for the kernel text section and only save
those pages if they are not contained within an NSS segment.
Fixes the following crash (and the above bugs as well):
Jump label code mismatch at netif_receive_skb_internal+0x28/0xd0
Found: c0 04 00 00 00 00
Expected: c0 f4 00 00 00 11
New: c0 04 00 00 00 00
Kernel panic - not syncing: Corrupted kernel text
CPU: 0 PID: 9 Comm: migration/0 Not tainted 3.19.0-01975-gb1b096e70f23 #4
Call Trace:
[<0000000000113972>] show_stack+0x72/0xf0
[<000000000081f15e>] dump_stack+0x6e/0x90
[<000000000081c4e8>] panic+0x108/0x2b0
[<000000000081be64>] jump_label_bug.isra.2+0x104/0x108
[<0000000000112176>] __jump_label_transform+0x9e/0xd0
[<00000000001121e6>] __sm_arch_jump_label_transform+0x3e/0x50
[<00000000001d1136>] multi_cpu_stop+0x12e/0x170
[<00000000001d1472>] cpu_stopper_thread+0xb2/0x168
[<000000000015d2ac>] smpboot_thread_fn+0x134/0x1b0
[<0000000000158baa>] kthread+0x10a/0x110
[<0000000000824a86>] kernel_thread_starter+0x6/0xc
Reported-and-tested-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Git commit d97d929f06 ("s390: move cacheinfo sysfs to generic cacheinfo
infrastructure") removed the general-instructions-extension availability
check before the ecag instruction is executed.
Without this check this may lead to crashes on machines without this facility.
Therefore add the check again where needed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As execution domain support is gone we can remove
signal translation from the signal code and remove
exec_domain from thread_info.
Signed-off-by: Richard Weinberger <richard@nod.at>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of adding another tkr field, rename this one to
tkr_mono. Also rename tk_read_base::base_mono to tk_read_base::base,
since the structure is not specific to CLOCK_MONOTONIC and the mono
name got added to the tk_read_base instance.
Lots of trivial churn.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150319093400.344679419@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a BUILD_BUG_ON() to enforce that irqclass_sub_desc contains the required
number of defined interrupt descriptions and won't be filled up with zeros.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename two more files which I forgot. Also remove the "asm" from the
swsusp_asm64.S file, since the ".S" suffix already makes it obvious
that this file contains assembler code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ipl.c uses 3 different macros to create a sysfs show function for ipl
attributes. Define IPL_ATTR_SHOW_FN which is used by all macros.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use macros wherever applicable and create a shutdown_action attribute
group to simplify the code.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use macros wherever applicable and put bin_attributes inside attribute_groups
to simplify/remove some code.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove __user address space annotation for sim_stor_event() calls since it
generates false positive warnings from sparse.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As reported by sparse these can and should be static.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the s390 architecture implementation of probe_kernel_write() and
instead use a new function s390_kernel_write() to modify kernel text and
data everywhere.
The s390 implementation of probe_kernel_write() was potentially broken
since it modified memory in a read-modify-write fashion, which read four
bytes, modified the requested bytes within those four bytes and wrote
the result back.
If two cpus would modify the same four byte area at different locations
within that area, this could lead to corruption.
Right now the only places which called probe_kernel_write() did run within
stop_machine_run. Therefore the scenario can't happen right now, however
that might change at any time.
To fix this rename probe_kernel_write() to s390_kernel_write() which can
have special semantics, like only call it while running within stop_machine().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of a translation exception the page tables are corrupted. If the
exception handler then calls die() which again calls show_regs()
-> show_code() -> copy_from_user(), the kernel may access the same memory
location again and generates yet another translation exception. Which in turn
will lead to a deadlock on the die_lock spinlock, which the kernel tries to
grab recursively.
Given that the page tables are corrupted anyway, if we see such an exception,
let's simply panic.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the 31 bit syscalls from the syscall table. This is a separate patch
just in case I screwed something up so it can be easily reverted.
However the conversion was done with a script, so everything should be ok.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename a couple of files to get rid of the "64" suffix.
"git blame" will still work.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.
The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e58 ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.
Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After a suspend/resume cycle we missed to enable smt again, which leads
to all sorts of bugs, since the kernel assumes smt is enabled, while the
hardware thinks it is not.
Reported-and-tested-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SF_CYCLES_BASIC_DIAG is always registered even if it is turned of in the
current hardware configuration. Because diagnostic-sampling is typically not
turned on in the hardware configuration, do not register this perf event by
default. Enable it only if the diagnostic-sampling function is authorized.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A long running project has been to clean up remaining uses
of clocksource_register(), replacing it with the simpler
clocksource_register_khz/hz() functions.
However, there are a few cases where we need to self-define
our mult/shift values, so switch the function to a more
obviously internal __clocksource_register() name, and
consolidate much of the internal logic so we don't have
duplication.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1426133800-29329-10-git-send-email-john.stultz@linaro.org
[ Minor cleanups. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
1. Several Fixes and enhancements
---------------------------------
- These 3 patches have cc stable:
b75f4c9 KVM: s390: Zero out current VMDB of STSI before including level3 data.
261520d KVM: s390: fix handling of write errors in the tpi handler
15462e3 KVM: s390: reinjection of irqs can fail in the tpi handler
2. SIMD support the kernel part (introduced with z13)
-----------------------------------------------------
- two KVM-generic changes in kvm.h:
1. New capability that can be enabled: KVM_CAP_S390_VECTOR_REGISTERS
2. increased padding size for sync regs in struct kvm_run to clarify that
sync regs can be larger than 1k. This is fine as this is the last
element in the structure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=bzDF
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-20150306' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into queue
KVM: s390: Features and Fixes for 4.1 (kvm/next)
1. Several Fixes and enhancements
---------------------------------
- These 3 patches have cc stable:
b75f4c9 KVM: s390: Zero out current VMDB of STSI before including level3 data.
261520d KVM: s390: fix handling of write errors in the tpi handler
15462e3 KVM: s390: reinjection of irqs can fail in the tpi handler
2. SIMD support the kernel part (introduced with z13)
-----------------------------------------------------
- two KVM-generic changes in kvm.h:
1. New capability that can be enabled: KVM_CAP_S390_VECTOR_REGISTERS
2. increased padding size for sync regs in struct kvm_run to clarify that
sync regs can be larger than 1k. This is fine as this is the last
element in the structure.
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Store additional status in the machine check handler, in order to
collect status (such as vector registers) that is not defined by
store status.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With git commit 4d92f50249 ("s390: reintroduce diag 44 calls for
cpu_relax()") I reintroduced a non-trivial cpu_relax() variant on s390.
The difference to the previous variant however is that the new version is
an out-of-line function, which will be traced if function tracing is enabled.
Switching to different tracers includes instruction patching. Therefore this
is done within stop_machine() "context" to prevent that any function tracing
is going on while instructions are being patched.
With the new out-of-line variant of cpu_relax() this is not true anymore,
since cpu_relax() gets called in a busy loop by all waiting cpus within
stop_machine() until function patching is finished.
Therefore cpu_relax() must be marked notrace.
This fixes kernel crashes when frequently switching between "function" and
"function_graph" tracers.
Moving cpu_relax() to a header file again, doesn't work because of header
include order dependencies.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
claw devices are outdated and no longer supported.
This patch removes the claw driver.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the output of the jump label sanity check and also print the
code pattern that is supposed to be written to the jump label.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
