Directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.
Directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes
Use personality() macro to compare only PER_MASK bytes and make sure that
we are setting only the bits that should be set, instead of overwriting
the whole value.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Checking for device mask to cover the whole IOMMU table is too strict.
IOMMU allocators should handle mask constraint properly for each
allocation.
The patch enables to use old AirPort Extreme cards on PowerMacs with
more than 1GB of memory; without the patch the driver init fails with:
b43-pci-bridge 0001:01:01.0: Warning: IOMMU window too big for device mask
b43-pci-bridge 0001:01:01.0: mask: 0x3fffffff, table end: 0x80000000
b43-phy0 ERROR: The machine/kernel does not support the required 30-bit DMA mask
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For powerpc BooKE and e200, singlestep is handled on the critical/dbg
exception stack. This causes current_thread_info() to fail for kgdb
internal, so previously We work around this issue by copying
the thread_info from the kernel stack before calling kgdb_handle_exception,
and copying it back afterwards.
But actually we don't do this properly. We should backup current_thread_info
then restore that when exit.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to skip a breakpoint exception when it occurs after
a breakpoint has already been removed.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kgdb_single_step flag has the possibility to indefinitely
hang the system on an SMP system.
The x86 arch have the same problem, and that problem was fixed by
commit 8097551d9ab9b9e3630(kgdb,x86: do not set kgdb_single_step
on x86). This patch does the same behaviors as x86's patch.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add several #includes that mpic_msgr relies on being pulled implicitly,
which only happens on certain configs.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Meador Inge <meador_inge@mentor.com>
Cc: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently if you are doing a global perf recording with hardware
breakpoints (ie perf record -e mem:0xdeadbeef -a), you can oops with:
Faulting instruction address: 0xc000000000738890
cpu 0xc: Vector: 300 (Data Access) at [c0000003f76af8d0]
pc: c000000000738890: .hw_breakpoint_handler+0xa0/0x1e0
lr: c000000000738830: .hw_breakpoint_handler+0x40/0x1e0
sp: c0000003f76afb50
msr: 8000000000001032
dar: 6f0
dsisr: 42000000
current = 0xc0000003f765ac00
paca = 0xc00000000f262a00 softe: 0 irq_happened: 0x01
pid = 6810, comm = loop-read
enter ? for help
[c0000003f76afbe0] c00000000073cd04 .notifier_call_chain.isra.0+0x84/0xe0
[c0000003f76afc80] c00000000073cdbc .notify_die+0x3c/0x60
[c0000003f76afd20] c0000000000139f0 .do_dabr+0x40/0xf0
[c0000003f76afe30] c000000000005a9c handle_dabr_fault+0x14/0x48
--- Exception: 300 (Data Access) at 0000000010000480
SP (ff8679e0) is in userspace
This is because we don't check to see if the break point is associated
with task before we deference the task_struct pointer.
This changes the update to use current.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a few whitespace goolies in xmon.c, some of them appear to
be my fault. Fix them all in one go.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the printk internals were reworked the xmon 'dl' command which
dumps the content of __log_buf has stopped working.
It is now a structured buffer, so just dumping it doesn't really work.
Use the helpers added for kgdb to print out the content.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Yocto (Built by Poky 7.0) 1.2 root filesystems fail to boot,
at least over nfs, with:
Failed to mount /dev: No such device
Configuring DEVTMPFS fixes it.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
run make savedefconfig on fsl defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Small platform specific bug fixes for problems found in randconfig builds.
* randconfig/mach:
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Using 'select' in Kconfig is hard, a platform cannot just
enable a driver without also making sure that its subsystem
is there. Also, there is no actual code dependency between
the platform and the gpio leds driver.
Without this patch, building without LEDS_CLASS esults in:
drivers/built-in.o: In function `create_gpio_led.part.2':
governor_userspace.c:(.devinit.text+0x5a58): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `gpio_led_remove':
governor_userspace.c:(.devexit.text+0x6b8): undefined reference to `led_classdev_unregister'
This reverts 8733f53c6 "ARM: ux500: Kconfig: Compile in leds-gpio
support for Snowball" that introduced the regression and did not
provide a helpful explanation.
In order to leave the GPIO LED code still present in normal
builds, this also enables the symbol in u8500_defconfig, in addition
to the other LED drivers that are already selected there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
The head-v7.S contains a call to the generic cpu_suspend function,
which is only available when selected by the i.MX6 code. As
pointed out by Shawn Guo, i.MX5 does not actually use any
functions defined in head-v7.S. It is also needed only for
the i.MX6 power management code and for the SMP code, so
we can restrict building this file to situations in which
at least one of those two is present.
Finally, other platforms with a similar file call it headsmp.S,
so we can rename it to the same for consistency.
Without this patch, building imx5 standalone results in:
arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
arch/arm/mach-imx/head-v7.S:104: undefined reference to `cpu_resume'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Miao <eric.miao@linaro.org>
Cc: stable@vger.kernel.org
The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.
Building IMX without CPU_FREQ_TABLE results in:
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org
The ksz9021rn_phy_fixup and mx6q_sabrelite functions try to
set up an ethernet phy if they can. They do check whether
phylib is enabled, but unfortunately the functions can only
be called from platform code if phylib is builtin, not
if it is a module
Without this patch, building with a modular phylib results in:
arch/arm/mach-imx/mach-imx6q.c: In function 'imx6q_sabrelite_init':
arch/arm/mach-imx/mach-imx6q.c:120:5: error: 'ksz9021rn_phy_fixup' undeclared (first use in this function)
arch/arm/mach-imx/mach-imx6q.c:120:5: note: each undeclared identifier is reported only once for each function it appears in
The bug was originally reported by Artem Bityutskiy but only
partially fixed in ef441806 "ARM: imx6q: register phy fixup only when
CONFIG_PHYLIB is enabled".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
This moves the imx5 pm code out of the list of unconditionally
compiled files for imx5, mirroring what we already do for imx6
and how it was done before the code was move from mach-mx5 to
mach-imx in v3.3.
Without this patch, building with CONFIG_PM disabled results in:
arch/arm/mach-imx/pm-imx5.c:202:116: error: redefinition of 'imx51_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:154:91: note: previous definition of 'imx51_pm_init' was here
arch/arm/mach-imx/pm-imx5.c:209:116: error: redefinition of 'imx53_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:155:91: note: previous definition of 'imx53_pm_init' was here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
The new omap4 cpuidle implementation currently requires
ARCH_NEEDS_CPU_IDLE_COUPLED, which only works on SMP.
This patch makes it possible to build a non-SMP kernel
for that platform. This is not normally desired for
end-users but can be useful for testing.
Without this patch, building rand-0y2jSKT results in:
drivers/cpuidle/coupled.c: In function 'cpuidle_coupled_poke':
drivers/cpuidle/coupled.c:317:3: error: implicit declaration of function '__smp_call_function_single' [-Werror=implicit-function-declaration]
It's not clear if this patch is the best solution for
the problem at hand. I have made sure that we can now
build the kernel in all configurations, but that does
not mean it will actually work on an OMAP44xx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/h+C
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij <linus.walleij@linaro.org>:
Here are two audio fixes for the ux500 found by Lee Jones.
* tag 'ux500-fixes-v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
For HDMI, already HDMI support for EXYNOS in mainline kernel is broken
because its configuration moved to platform data but regarding platform
data didn't support yet. And others are for fix warnings.
* 'v3.6-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set HDMI platform data in Origen board
ARM: EXYNOS: Set HDMI platform data in SMDKV310
ARM: SAMSUNG: Add API to set platform data for s5p-tv driver
ARM: SAMSUNG: Set HDMI platform data for Exynos4x12 SoCs
ARM: Samsung: Make uart_save static in pm.c file
ARM: S3C24XX: Fix s3c2410_dma_enqueue parameters
ARM: S3C24XX: Add missing DMACH_DT_PROP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When we are finished with return PFNs to the hypervisor, then
populate it back, and also mark the E820 MMIO and E820 gaps
as IDENTITY_FRAMEs, we then call P2M to set areas that can
be used for ballooning. We were off by one, and ended up
over-writting a P2M entry that most likely was an IDENTITY_FRAME.
For example:
1-1 mapping on 40000->40200
1-1 mapping on bc558->bc5ac
1-1 mapping on bc5b4->bc8c5
1-1 mapping on bc8c6->bcb7c
1-1 mapping on bcd00->100000
Released 614 pages of unused memory
Set 277889 page(s) to 1-1 mapping
Populating 40200-40466 pfn range: 614 pages added
=> here we set from 40466 up to bc559 P2M tree to be
INVALID_P2M_ENTRY. We should have done it up to bc558.
The end result is that if anybody is trying to construct
a PTE for PFN bc558 they end up with ~PAGE_PRESENT.
CC: stable@vger.kernel.org
Reported-by-and-Tested-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the controller has no PCIe module attached, accessing of the device
configuration space causes a data bus error. Avoid this by checking the
status of the PCIe link in advance, and indicate an error if the link
is down.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4293/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The binding doc and dts use properties "fsl,{cd,wp}-internal" while
esdhc driver uses "fsl,{cd,wp}-controller". Fix binding doc and dts
to get them match driver code.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Chris Ball <cjb@laptop.org>
Though commit 602bf40 (ARM: imx6: exit coherency when shutting down
a cpu) improves the stability of imx6q cpu hotplug a lot, there are
still hangs seen with a more stressful hotplug testing.
It's expected that once imx_enable_cpu(cpu, false) is called, the cpu
will be taken down by hardware immediately, and the code after that
will not get any chance to execute. However, this is not always the
case from the testing. The cpu could possibly be alive for a few
cycles before hardware actually takes it down. So rather than letting
cpu execute some code that could cause a hang in these cycles, let's
make the cpu spin there and wait for hardware to take it down.
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove the malformed "mem=" bootargs parameter in at91sam9g25ek.dts
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AT91_ID_SYS as virq is incorrect because of spare irq support which
introduces NR_IRQS_LEGACY offset. It modifies rtc-at91sam9 driver in
order to get irq from resources.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AT91_ID_SYS as virq is incorrect because of spare irq support which
introduces NR_IRQS_LEGACY offset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This issue was recently observed on an AMD C-50 CPU where a patch of
maximum size was applied.
Commit be62adb492 ("x86, microcode, AMD: Simplify ucode verification")
added current_size in get_matching_microcode(). This is calculated as
size of the ucode patch + 8 (ie. size of the header). Later this is
compared against the maximum possible ucode patch size for a CPU family.
And of course this fails if the patch has already maximum size.
Cc: <stable@vger.kernel.org> [3.3+]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-1-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The sub-register used to access the stack (sp, esp, or rsp) is not
determined by the address size attribute like other memory references,
but by the stack segment's B bit (if not in x86_64 mode).
Fix by using the existing stack_mask() to figure out the correct mask.
This long-existing bug was exposed by a combination of a27685c33a
(emulate invalid guest state by default), which causes many more
instructions to be emulated, and a seabios change (possibly a bug) which
causes the high 16 bits of esp to become polluted across calls to real
mode software interrupts.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Although the possible race described in
commit 85b7059169
KVM: MMU: fix shrinking page from the empty mmu
was correct, the real cause of that issue was a more trivial bug of
mmu_shrink() introduced by
commit 1952639665
KVM: MMU: do not iterate over all VMs in mmu_shrink()
Here is the bug:
if (kvm->arch.n_used_mmu_pages > 0) {
if (!nr_to_scan--)
break;
continue;
}
We skip VMs whose n_used_mmu_pages is not zero and try to shrink others:
in other words we try to shrink empty ones by mistake.
This patch reverses the logic so that mmu_shrink() can free pages from
the first VM whose n_used_mmu_pages is not zero. Note that we also add
comments explaining the role of nr_to_scan which is not practically
important now, hoping this will be improved in the future.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
sh73a0 :: intca_irq_pins_desc irq table had conflict
from irq 552 to irq 557 before.
But the second controller was simply trampling the
first one by way of the -EEXIST case from irq_alloc_desc_at().
But now, we have irqdomain support from
1d6a21b0a6
(sh: intc: initial irqdomain support)
The irqdomain code has simply tightened down the sanity checks and
error path. So, sh73a0 CPU board got some WARNING when booting now.
This patch fixup RELOC_BASE to solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Probably a leftover from the early days of self-patching, p6nops
are marked __initconst_or_module, which causes them to be
discarded in a non-modular kernel. If something later triggers
patching, it will overwrite kernel code with garbage.
Reported-by: Tomas Racek <tracek@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/5034AE84.90708@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When one CPU is going down and this CPU is the last one in irq
affinity, current code is setting cpu_all_mask as the new
affinity for that irq.
But for some systems (such as in Medfield Android mobile) the
firmware sends the interrupt to each CPU in the irq affinity
mask, averaged, and cpu_all_mask includes all potential CPUs,
i.e. offline ones as well.
So replace cpu_all_mask with cpu_online_mask.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/27240C0AC20F114CBF8149A2696CBE4A137286@SHSMSX101.ccr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This comment is no longer true. We support up to 2^16 CPUs
because __ticket_t is an u16 if NR_CPUS is larger than 256.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Each page mapped in a process's address space must be correctly
accounted for in _mapcount. Normally the rules for this are
straightforward but hugetlbfs page table sharing is different. The page
table pages at the PMD level are reference counted while the mapcount
remains the same.
If this accounting is wrong, it causes bugs like this one reported by
Larry Woodman:
kernel BUG at mm/filemap.c:135!
invalid opcode: 0000 [#1] SMP
CPU 22
Modules linked in: bridge stp llc sunrpc binfmt_misc dcdbas microcode pcspkr acpi_pad acpi]
Pid: 18001, comm: mpitest Tainted: G W 3.3.0+ #4 Dell Inc. PowerEdge R620/07NDJ2
RIP: 0010:[<ffffffff8112cfed>] [<ffffffff8112cfed>] __delete_from_page_cache+0x15d/0x170
Process mpitest (pid: 18001, threadinfo ffff880428972000, task ffff880428b5cc20)
Call Trace:
delete_from_page_cache+0x40/0x80
truncate_hugepages+0x115/0x1f0
hugetlbfs_evict_inode+0x18/0x30
evict+0x9f/0x1b0
iput_final+0xe3/0x1e0
iput+0x3e/0x50
d_kill+0xf8/0x110
dput+0xe2/0x1b0
__fput+0x162/0x240
During fork(), copy_hugetlb_page_range() detects if huge_pte_alloc()
shared page tables with the check dst_pte == src_pte. The logic is if
the PMD page is the same, they must be shared. This assumes that the
sharing is between the parent and child. However, if the sharing is
with a different process entirely then this check fails as in this
diagram:
parent
|
------------>pmd
src_pte----------> data page
^
other--------->pmd--------------------|
^
child-----------|
dst_pte
For this situation to occur, it must be possible for Parent and Other to
have faulted and failed to share page tables with each other. This is
possible due to the following style of race.
PROC A PROC B
copy_hugetlb_page_range copy_hugetlb_page_range
src_pte == huge_pte_offset src_pte == huge_pte_offset
!src_pte so no sharing !src_pte so no sharing
(time passes)
hugetlb_fault hugetlb_fault
huge_pte_alloc huge_pte_alloc
huge_pmd_share huge_pmd_share
LOCK(i_mmap_mutex)
find nothing, no sharing
UNLOCK(i_mmap_mutex)
LOCK(i_mmap_mutex)
find nothing, no sharing
UNLOCK(i_mmap_mutex)
pmd_alloc pmd_alloc
LOCK(instantiation_mutex)
fault
UNLOCK(instantiation_mutex)
LOCK(instantiation_mutex)
fault
UNLOCK(instantiation_mutex)
These two processes are not poing to the same data page but are not
sharing page tables because the opportunity was missed. When either
process later forks, the src_pte == dst pte is potentially insufficient.
As the check falls through, the wrong PTE information is copied in
(harmless but wrong) and the mapcount is bumped for a page mapped by a
shared page table leading to the BUG_ON.
This patch addresses the issue by moving pmd_alloc into huge_pmd_share
which guarantees that the shared pud is populated in the same critical
section as pmd. This also means that huge_pte_offset test in
huge_pmd_share is serialized correctly now which in turn means that the
success of the sharing will be higher as the racing tasks see the pud
and pmd populated together.
Race identified and changelog written mostly by Mel Gorman.
{akpm@linux-foundation.org: attempt to make the huge_pmd_share() comment comprehensible, clean up coding style]
Reported-by: Larry Woodman <lwoodman@redhat.com>
Tested-by: Larry Woodman <lwoodman@redhat.com>
Reviewed-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Ken Chen <kenchen@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68knommu arch fixes from Greg Ungerer:
"This contains 2 fixes. One fixes compilation of ColdFire clk code,
the other makes sure we use the generic atomic64 support on all m68k
targets."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: select CONFIG_GENERIC_ATOMIC64 for all m68k CPU types
m68knommu: select CONFIG_HAVE_CLK for ColdFire CPU types
On s390x-linux-gcc, __SIZE_TYPE__ expands to "long unsigned int" for both
32-bit s390 and 64-bit s390x, as
gcc-4.6.3-nolibc/s390x-linux/lib/gcc/s390x-linux/4.6.3/plugin/include/config/s390/linux.h
has
#define SIZE_TYPE (TARGET_64BIT ? "long unsigned int" : "long unsigned int")
To match this, __kernel_size_t is always set to "long unsigned int".
But while __kernel_ssize_t is "long" on 64-bit s390x, it is "int" on 32-bit
s390, causing compiler warnings like:
fs/quota/quota_tree.c:372:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'ssize_t' [-Wformat]
To fix this, __kernel_ssize_t should be "long", irrespective of word size.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 7c5763b845 (drivers:misc: Remove MISC_DEVICES config option) removed
CONFIG_MISC_DEVICES option, so remove the occurrences from the config files
as well.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull x86 fixes from Ingo Molnar.
A x32 socket ABI fix with a -stable backport tag among other fixes.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x32: Use compat shims for {g,s}etsockopt
Revert "x86-64/efi: Use EFI to deal with platform wall clock"
x86, apic: fix broken legacy interrupts in the logical apic mode
x86, build: Globally set -fno-pic
x86, avx: don't use avx instructions with "noxsave" boot param
Merge alpha architecture update from Michael Cree:
"The Alpha Maintainer, Matt Turner, is currently unavailable, so I have
collected up patches that have been posted to the linux-alpha mailing
list over the last couple of months, and are forwarding them to you in
the hope that you are prepared to accept them via me.
The patches by Al Viro and myself I have been running against kernels
for two months now so have had quite a bit of testing. All except one
patch were intended for the 3.5 kernel but because of Matt's
unavailability never got forwarded to you."
* emailed patches from Michael Cree <mcree@orcon.net.nz>: (9 commits)
alpha: Fix fall-out from disintegrating asm/system.h
Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
alpha: fix fpu.h usage in userspace
alpha/mm/fault.c: Port OOM changes to do_page_fault
alpha: take kernel_execve() out of entry.S
alpha: take a bunch of syscalls into osf_sys.c
alpha: Use new generic strncpy_from_user() and strnlen_user()
alpha: Wire up cross memory attach syscalls
alpha: Don't export SOCK_NONBLOCK to user space.
Commit ec2212088c ("Disintegrate asm/system.h for Alpha") removed
asm/system.h however arch/alpha/oprofile/common.c requires definitions
that were shifted from asm/system.h to asm/special_insns.h. Include
that.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following build error occurred during an alpha build:
net/core/sock.c:274:36: error: initializer element is not constant
Dave Anglin says:
> Here is the line in sock.i:
>
> struct static_key memalloc_socks = ((struct static_key) { .enabled =
> ((atomic_t) { (0) }) });
The above line contains two compound literals. It also uses a designated
initializer to initialize the field enabled. A compound literal is not a
constant expression.
The location of the above statement isn't fully clear, but if a compound
literal occurs outside the body of a function, the initializer list must
consist of constant expressions.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit ec2212088c ("Disintegrate asm/system.h for Alpha"), the
fpu.h header which we install for userland started depending on
special_insns.h which is not installed.
However, fpu.h only uses that for __KERNEL__ code, so protect the
inclusion the same way to avoid build breakage in glibc:
/usr/include/asm/fpu.h:4:31: fatal error: asm/special_insns.h: No such file or directory
Cc: stable@vger.kernel.org
Reported-by: Matt Turner <mattst88@gentoo.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d065bd810b ("mm: retry page fault when blocking on disk
transfer") and 37b23e0525 ("x86,mm: make pagefault killable")
introduced changes into the x86 pagefault handler for making the page
fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial during OOM
killer invocation.
Port these changes to ALPHA.
Signed-off-by: Mohd. Faris <mohdfarisq2010@gmail.com>
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New helper: current_thread_info(). Allows to do a bunch of odd syscalls
in C. While we are at it, there had never been a reason to do
osf_getpriority() in assembler. We also get "namespace"-aware (read:
consistent with getuid(2), etc.) behaviour from getx?id() syscalls now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Similar to x86/sparc/powerpc implementations except:
1) we implement an extremely efficient has_zero()/find_zero()
sequence with both prep_zero_mask() and create_zero_mask()
no-operations.
2) Our output from prep_zero_mask() differs in that only the
lowest eight bits are used to represent the zero bytes
nevertheless it can be safely ORed with other similar masks
from prep_zero_mask() and forms input to create_zero_mask(),
the two fundamental properties prep_zero_mask() must satisfy.
Tests on EV67 and EV68 CPUs revealed that the generic code is
essentially as fast (to within 0.5% of CPU cycles) of the old
Alpha specific code for large quadword-aligned strings, despite
the 30% extra CPU instructions executed. In contrast, the
generic code for unaligned strings is substantially slower (by
more than a factor of 3) than the old Alpha specific code.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add sys_process_vm_readv and sys_process_vm_writev to Alpha.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we export SOCK_NONBLOCK to user space but that conflicts with
the definition from glibc leading to compilation errors in user programs
(e.g. see Debian bug #658460).
The generic socket.h restricts the definition of SOCK_NONBLOCK to the
kernel, as does the MIPS specific socket.h, so let's do the same on
Alpha.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM fixes from Russell King:
"The largest thing in this set of changes is bringing back some of the
ARMv3 code to fix a compile problem noticed on RiscPC, which we still
support, even though we only support ARMv4 there.
(The reason is that the system bus doesn't support ARMv4 half-word
accesses, so we need the ARMv3 library code for this platform.)
The rest are all quite minor fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7490/1: Drop duplicate select for GENERIC_IRQ_PROBE
ARM: Bring back ARMv3 IO and user access code
ARM: 7489/1: errata: fix workaround for erratum #720789 on UP systems
ARM: 7488/1: mm: use 5 bits for swapfile type encoding
ARM: 7487/1: mm: avoid setting nG bit for user mappings that aren't present
ARM: 7486/1: sched_clock: update epoch_cyc on resume
ARM: 7484/1: Don't enable GENERIC_LOCKBREAK with ticket spinlocks
ARM: 7483/1: vfp: only advertise VFPv4 in hwcaps if CONFIG_VFPv3 is enabled
ARM: 7482/1: topology: fix section mismatch warning for init_cpu_topology
Some of the arguments to {g,s}etsockopt are passed in userland pointers.
If we try to use the 64bit entry point, we end up sometimes failing.
For example, dhcpcd doesn't run in x32:
# dhcpcd eth0
dhcpcd[1979]: version 5.5.6 starting
dhcpcd[1979]: eth0: broadcasting for a lease
dhcpcd[1979]: eth0: open_socket: Invalid argument
dhcpcd[1979]: eth0: send_raw_packet: Bad file descriptor
The code in particular is getting back EINVAL when doing:
struct sock_fprog pf;
setsockopt(s, SOL_SOCKET, SO_ATTACH_FILTER, &pf, sizeof(pf));
Diving into the kernel code, we can see:
include/linux/filter.h:
struct sock_fprog {
unsigned short len;
struct sock_filter __user *filter;
};
net/core/sock.c:
case SO_ATTACH_FILTER:
ret = -EINVAL;
if (optlen == sizeof(struct sock_fprog)) {
struct sock_fprog fprog;
ret = -EFAULT;
if (copy_from_user(&fprog, optval, sizeof(fprog)))
break;
ret = sk_attach_filter(&fprog, sk);
}
break;
arch/x86/syscalls/syscall_64.tbl:
54 common setsockopt sys_setsockopt
55 common getsockopt sys_getsockopt
So for x64, sizeof(sock_fprog) is 16 bytes. For x86/x32, it's 8 bytes.
This comes down to the pointer being 32bit for x32, which means we need
to do structure size translation. But since x32 comes in directly to
sys_setsockopt, it doesn't get translated like x86.
After changing the syscall table and rebuilding glibc with the new kernel
headers, dhcp runs fine in an x32 userland.
Oddly, it seems like Linus noted the same thing during the initial port,
but I guess that was missed/lost along the way:
https://lkml.org/lkml/2011/8/26/452
[ hpa: tagging for -stable since this is an ABI fix. ]
Bugzilla: https://bugs.gentoo.org/423649
Reported-by: Mads <mads@ab3.no>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Link: http://lkml.kernel.org/r/1345320697-15713-1-git-send-email-vapier@gentoo.org
Cc: H. J. Lu <hjl.tools@gmail.com>
Cc: <stable@vger.kernel.org> v3.4..v3.5
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If P2M leaf is completly packed with INVALID_P2M_ENTRY or with
1:1 PFNs (so IDENTITY_FRAME type PFNs), we can swap the P2M leaf
with either a p2m_missing or p2m_identity respectively. The old
page (which was created via extend_brk or was grafted on from the
mfn_list) can be re-used for setting new PFNs.
This also means we can remove git commit:
5bc6f9888d
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back
which tried to fix this.
and make the amount that is required to be reserved much smaller.
CC: stable@vger.kernel.org # for 3.5 only.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Previous attempts to add platform probing of the Audio related devices
only call from non-DT initialisation functions. This patch extends that
functionality to the Device Tree related ones too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The platform attempts to register platform device 'snd_soc_u8500'
which doesn't actually exist. Here we change the reference to the
correct one 'snd_soc_mop500'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2ec8663f9c03a96f2c328c7c483603c31d62ad37 (lmo) rsp.
497e5ff03f (kernel.org) [MIPS: Malta: Move
PIIX4 PCI fixup to where it belongs.] attempted to move this PCI fixup
but really only added it at it's new location without deleting the old
instance.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ath79 platform code allows to run a single kernel image on various
SoCs which are based on the 24Kc and 74Kc cores. The current code
explicitely disables the DSP ASE, but that is available in the 74Kc core.
Remove the override in order to let the kernel to detect the availability
of the DSP ASE at runtime.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current implementation of synchronise_count_{master,slave} blocks
slave CPUs in early boot until all of them come up. This no longer
works because blocking a CPU with interrupts off after notifying the
CPU to be online causes problems with the current kernel.
Specifically, after the workqueue changes
(commit a08489c569 "Pull workqueue changes from Tejun Heo")
the CPU_ONLINE notification callback workqueue_cpu_up_callback()
will hang on wait_for_completion(&idle_rebind.done), if the slave
CPUs are blocked for synchronize_count_slave().
The changes are to update synchronize_count_{master,slave}() to handle
one CPU at a time and to call synchronise_count_master() in __cpu_up()
so that the CPU_ONLINE notification goes out only after the COP0 COUNT
register is synchronized.
[ralf@linux-mips.org: This matter only to those few platforms which are
using the cp0 counter as their clocksource which are XLP, XLR and MIPS'
CMP solution.]
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In case a series of R_MIPS_HI16 relocations was not followed by an
R_MIPS_LO16 relocation we were leaking the hi16 relocation chain.
Handle that error and return an error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace. In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore. Fix race by moving it into
mod_arch_specific.
[ralf@linux-mips.org: folded in Tony's followup fix. Thanks Tony!]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/4189/
Commit 6f5d2e970452b5c86906adcb8e7ad246f535ba39 (lmo) /
477c4b0740 (kernel.org) [[MIPS: VPE: Free
relocation chain on error.] fixed the same issue in the vpe loader in 2009
but back then the same bug in module.c went unfixed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Akhilesh Kumar <akhilesh.lxr@gmail.com>
Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
We see only the CardBus device:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]
Later the device driver shows this error:
ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5
I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.
What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is needed in order to get rid of the following errors:
arch/mips/ath79/clock.c:353:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/ath79/clock.c:377:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/ath79/clock.c:383:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/ath79/clock.c:388:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/ath79/clock.c:394:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4170/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The currently assigned IRQ number to the OHCI controller is incorrect for
the AR7240 SoC, and that leads to the following error message from the
OHCI driver:
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ath79-ohci ath79-ohci: Atheros built-in OHCI controller
ath79-ohci ath79-ohci: new USB bus registered, assigned bus number 1
ath79-ohci ath79-ohci: irq 14, io mem 0x1b000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new full-speed USB device number 2 using ath79-ohci
ath79-ohci ath79-ohci: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Fix this by using the correct IRQ number.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 3.6.0-rc1, We are getting many messages like:
WARNING: at kernel/irq/irqdomain.c:444 irq_domain_associate_many+0x23c/0x260()
Modules linked in:
Call Trace:
[<ffffffff814cb698>] dump_stack+0x8/0x34
[<ffffffff81133d00>] warn_slowpath_common+0x78/0xa8
[<ffffffff81187e44>] irq_domain_associate_many+0x23c/0x260
[<ffffffff81187f38>] irq_create_mapping+0xd0/0x220
[<ffffffff81188104>] irq_create_of_mapping+0x7c/0x158
[<ffffffff813e5f08>] irq_of_parse_and_map+0x28/0x40
.
.
.
Both the CIU and GPIO interrupt domains were somewhat screwed up.
For the CIU domain, we need to call irq_domain_associate() for each of
the preassigned irq numbers. For the GPIO domain, we were applying
the register bit offset in octeon_irq_gpio_xlat, but it should be done
in octeon_irq_gpio_map instead.
Also: Reserve all 8 'core' irqs for the 'core' irq_chip so that they
don't get used by the other domains. Remove unused OCTEON_IRQ_*
symbols.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ldb_di[01]_podf is implemented as a clk-divider that
divides by 1 or 2. In reality, the ldb_di[01]_ipu_div
dividers divide by either 3.5 or 7. Adding a fixed factor
of 1/3.5 fixes their children's clock rates.
This should probably be converted to rate table based dividers,
once available.
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is no specific atomic64 support code for any m68k CPUs, so we should
select CONFIG_GENERIC_ATOMC64 for all. Remove the existing per CPU selection
of this and select it for all m68k.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQKlV9AAoJEFjIrFwIi8fJZh4H/0ZlRrgG+8mqwCM+pcyYY+2a
zqnOrfYUO/aO26oqiOQUrn4quLAElhBuJK19uSj8fckMMZ+sr5rTJTaXmT6b7F7N
pgTXsKQCYAJ2NNGHVSQ73KYjOUeEW3woDSQZo0y/GRzOjiQsxpoFc8PS94ZieUNT
G6a8ECZBRv3fz8nAuJlhGV/suqHGOLJ0pwum1gHGOzaH3ZoZVtaQv5LhGYctJspU
yF5bdeD0qjCbseVtJ72tyxzLxMwLpJtdy2MbSwIv5JGuszj0nRmL4oa7Vc4vYdyv
p+FrNmbDAZ1j61z1PhBZPmgzwba2LTXtIWhR2zsGJgqlJNzMUtlNkff1kT3NeE0=
=Gl6V
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
This reverts commit 00e37bdb01.
During shutdown of PVHVM guests with more than 2VCPUs on certain
machines we can hit the race where the replaced shared_info is not
replaced fast enough and the PV time clock retries reading the same
area over and over without any any success and is stuck in an
infinite loop.
Acked-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Put the parameters the right way around
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=44031
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When we map a page that wasn't icache cleared before, do so when first
mapping it in KVM using the same information bits as the Linux mapping
logic. That way we are 100% sure that any page we map does not have stale
entries in the icache.
Signed-off-by: Alexander Graf <agraf@suse.de>
In handling the H_CEDE hypercall, if this vcpu has already been
prodded (with the H_PROD hypercall, which Linux guests don't in fact
use), we branch to a numeric label '1f'. Unfortunately there is
another '1:' label before the one that we want to jump to. This fixes
the problem by using a textual label, 'kvm_cede_prodded'. It also
changes the label for another longish branch from '2:' to
'kvm_cede_exit' to avoid a possible future problem if code modifications
add another numeric '2:' label in between.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull two sparc fixes from David S. Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
The generic atomic64 support came in 2009 to support the perf subsystem
with the expectation that all architectures would implement atomic64
support. Since then, other optional parts of the generic kernel have
also come to expect atomic64 support. This patch enables generic atomic64
support for C6X architecture.
Signed-off-by: Mark Salter <msalter@redhat.com>
C6X currently lacks Lx_CACHE_SHIFT defines which are needed in a
few places in the generic kernel. This patch adds _SHIFT defines
for the various caches and bases the Lx_CACHE_BYTES defines on
them.
Signed-off-by: Mark Salter <msalter@redhat.com>
From Jason Cooper <jason@lakedaemon.net>:
Small fixes for the orion platforms including kirkwood.
* 'fixes-for-v3.6' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While building the dtbs target, one is getting:
make dtbs
make[1]: *** No rule to make target `arch/arm/boot/kirkwood-qnap-ts219.dtb', needed by `arch/arm/boot/dtbs'. Stop.
make: *** [dtbs] Error 2
The reason is that there's no kirkwood-qnap-ts219.dts file. Update Makefile.boot
to reflect the dts files present.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
While converting, a led has been missed leading to wrong power blue led
definition. Add it back and fix the gpio used on the power blue led.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The mv643xx ethernet controller limits the packet size for the TX
checksum offloading. This patch sets this limits for Kirkwood and
Dove which have smaller limits that the default.
As a side note, this patch is an updated version of a patch sent some years
ago: http://lists.infradead.org/pipermail/linux-arm-kernel/2010-June/017320.html
which seems to have been lost.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: <stable@vger.kernel.org>
PM related.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wnJX
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes for issues noted during the merge window, mostly
PM related.
* tag 'omap-fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
ARM: OMAP2+: cpu: Add am33xx device under cpu_class_is_omap2
omap: Fix multi.h when only ARCH_OMAP3 and SOC_AM33XX are selected
ARM: OMAP2+: Fix dmtimer set source clock failure
Revert "ARM: OMAP3: PM: call pre/post transition per powerdomain"
ARM: OMAP3: TWL4030: ensure sys_nirq1 is mux'd and wakeup enabled
omap2: mux: remove comment for nonexistent member
OMAP: remove unused parameter arch_id from uncompress.h
arm/dts: Mark vcxio, v2v1 and v1v8 regulators as always on
OMAP2+: Fix random config build break with !ARM_CPU_SUSPEND
arm/dts: Fix am33xx wdt node
ARM: OMAP3: igep0020: set GPIO mode for mux mcspi1_cs2 pin
Revert "ARM: OMAP3530evm: set pendown_state and debounce time for ads7846"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Seems that Thomas' and my patches collided during the last merge
window.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bacef661ac.
This commit has been found to cause serious regressions on a number of
ASUS machines at the least. We probably need to provide a 1:1 map in
addition to the EFI virtual memory map in order for this to work.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reported-and-bisected-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120805172903.5f8bb24c@zougloub.eu
Recent commit 332afa656e cleaned up
a workaround that updates irq_cfg domain for legacy irq's that
are handled by the IO-APIC. This was assuming that the recent
changes in assign_irq_vector() were sufficient to remove the workaround.
But this broke couple of AMD platforms. One of them seems to be
sending interrupts to the offline cpu's, resulting in spurious
"No irq handler for vector xx (irq -1)" messages when those cpu's come online.
And the other platform seems to always send the interrupt to the last logical
CPU (cpu-7). Recent changes had an unintended side effect of using only logical
cpu-0 in the IO-APIC RTE (during boot for the legacy interrupts) and this
broke the legacy interrupts not getting routed to the cpu-7 on the AMD
platform, resulting in a boot hang.
For now, reintroduce the removed workaround, (essentially not allowing the
vector to change for legacy irq's when io-apic starts to handle the irq. Which
also addressed the uninteded sife effect of just specifying cpu-0 in the
IO-APIC RTE for those irq's during boot).
Reported-and-tested-by: Robert Richter <robert.richter@amd.com>
Reported-and-tested-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1344453412.29170.5.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
Patch b6d1c33a31 "ARM: Orion: Consolidate the address map setup" tried
to merge the address map for the four orion platforms, but apparently
got it wrong for mv78xx0. Admittedly I don't understand what this
code actually does, but it's clear that the current version is
wrong.
Without this patch, building mv78xx0_defconfig results in:
arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: (near initialization for 'addr_map_cfg.win_cfg_base') [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Michael Walle <michael@walle.cc>
Cc: Nicolas Pitre <nico@linaro.org>
If PMU counter has PEBS enabled it is not enough to disable counter
on a guest entry since PEBS memory write can overshoot guest entry
and corrupt guest memory. Disabling PEBS during guest entry solves
the problem.
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120809085234.GI3341@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Westmere-EX uncore is similar to the Nehalem-EX uncore. The
differences are:
- Westmere-EX uncore has 10 instances of Cbox. The MSRs for Cbox8
and Cbox9 in the Westmere-EX aren't contiguous with Cbox 0~7.
- The fvid field in the ZDP_CTL_FVC register in the Mbox is
different. It's 5 bits in the Nehalem-EX, 6 bits in the
Westmere-EX.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1344229882-3907-3-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch includes following fixes and update:
- Only some events in the Sbox and Mbox can use the match/mask
registers, add code to check this.
- The format definitions for xbr_mm_cfg and xbr_match registers
in the Rbox are wrong, xbr_mm_cfg should use 32 bits, xbr_match
should use 64 bits.
- Cleanup the Rbox code. Compute the addresses extra registers in
the enable_event function instead of the hw_config function.
This simplifies the code in nhmex_rbox_alter_er().
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1344229882-3907-2-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the following section mismatch:
WARNING: arch/x86/kernel/cpu/built-in.o(.text+0x7ad9): Section mismatch in reference from the function uncore_types_exit() to the function .init.text:uncore_type_exit()
The function uncore_types_exit() references the function __init
uncore_type_exit(). This is often because uncore_types_exit lacks a
__init annotation or the annotation of uncore_type_exit is wrong.
caused by 14371cce03 ("perf: Add generic PCI uncore PMU device
support").
Cc: Zheng Yan <zheng.z.yan@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1339741902-8449-8-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Calling omap_dm_timer_prepare while the spinlock is held is not
allowed as sleeping functions are called later on during the
preparation (namely within clk_get()).
dm_timer_lock is only required for protecting the
omap_timer_list. After the timer is marked as reserved, the lock is no
longer needed and should be freed.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This partially reverts 357c9c1f07
(ARM: Remove support for ARMv3 ARM610 and ARM710 CPUs).
Although we only support StrongARM on the RiscPC, we need to keep the
ARMv3 user access code for this platform because the bus does not
understand half-word load/stores.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WsZj
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
* tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers/gpio/gpio-langwell.c: fix error return code
gpio: samsung: Fix off-by-one bug in gpio addresses
ARM: dts: imx: add alias for gpio
gpio/mxc: specify gpio base for device tree probe
gpio/mxc: remove redundant shadow variables initialization
GPIO: gpio-pxa: fix devicetree functions
gpio: msic: Fix calculating register address in msic_gpio_to_oreg()
gpio-sch: Fix leak of resource
These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file. The largest part of the fixes
are patches that address bugs found by building all the ARM defconfig
files. There are a lot more warnings that we have patches for, but
the others are either still under discussion or are harmless and
do not cause actual problems besides making the build slightly noisy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=TmsX
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Arnd Bergmann:
"These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file.
The largest part of the fixes are patches that address bugs found by
building all the ARM defconfig files. There are a lot more warnings
that we have patches for, but the others are either still under
discussion or are harmless and do not cause actual problems besides
making the build slightly noisy."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: davinci: remove broken ntosd2_init_i2c
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
ARM: imx: gpmi-nand depends on mxs-dma
ARM: integrator: include <linux/export.h>
ARM: s3c24xx: use new PWM driver
ARM: sa1100: include linux/io.h in hackkit leds code
Input: eeti_ts: pass gpio value instead of IRQ
ARM: pxa: remove irq_to_gpio from ezx-pcap driver
ARM: tegra: more regulator fixes for Harmony
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
ARM: kirkwood: fix typo in Makefile.boot
i.MX27: Fix emma-prp and csi clocks.
ARM: integrator: use clk_prepare_enable() for timer
MAINTAINERS: update entry for Linus Walleij
...
Pull three dma-mapping fixes from Marek Szyprowski.
* 'fixes-for-linus-for-3.6-rc2' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: fix incorrect freeing of atomic allocations
ARM: dma-mapping: fix atomic allocation alignment
ARM: mm: fix MMU mapping of CMA regions
Commit 5a783cbc48 ("ARM: 7478/1: errata: extend workaround for erratum
#720789") added workarounds for erratum #720789 to the range TLB
invalidation functions with the observation that the erratum only
affects SMP platforms. However, when running an SMP_ON_UP kernel on a
uniprocessor platform we must take care to preserve the ASID as the
workaround is not required.
This patch ensures that we don't set the ASID to 0 when flushing the TLB
on such a system, preserving the original behaviour with the workaround
disabled.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Page migration encodes the pfn in the offset field of a swp_entry_t.
For LPAE, we support physical addresses of up to 36 bits (due to
sparsemem limitations with the size of page flags), requiring 24 bits
to represent a pfn. A further 3 bits are used to encode a swp_entry into
a pte, leaving 5 bits for the type field. Furthermore, the core code
defines MAX_SWAPFILES_SHIFT as 5, so the additional type bit does not
get used.
This patch reduces the width of the type field to 5 bits, allowing us
to create up to 31 swapfiles of 64GB each.
Cc: <stable@vger.kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Swap entries are encoding in ptes such that !pte_present(pte) and
pte_file(pte). The remaining bits of the descriptor are used to identify
the swapfile and offset within it to the swap entry.
When writing such a pte for a user virtual address, set_pte_at
unconditionally sets the nG bit, which (in the case of LPAE) will
corrupt the swapfile offset and lead to a BUG:
[ 140.494067] swap_free: Unused swap offset entry 000763b4
[ 140.509989] BUG: Bad page map in process rs:main Q:Reg pte:0ec76800 pmd:8f92e003
This patch fixes the problem by only setting the nG bit for user
mappings that are actually present.
Cc: <stable@vger.kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many clocks that are used to provide sched_clock will reset during
suspend. If read_sched_clock returns 0 after suspend, sched_clock will
appear to jump forward. This patch resets cd.epoch_cyc to the current
value of read_sched_clock during resume, which causes sched_clock() just
after suspend to return the same value as sched_clock() just before
suspend.
In addition, during the window where epoch_ns has been updated before
suspend, but epoch_cyc has not been updated after suspend, it is unknown
whether the clock has reset or not, and sched_clock() could return a
bogus value. Add a suspended flag, and return the pre-suspend epoch_ns
value during this period.
The new behavior is triggered by calling setup_sched_clock_needs_suspend
instead of setup_sched_clock.
Signed-off-by: Colin Cross <ccross@android.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that ARM has implemented its spinlocks with tickets we don't
need to use the generic lockbreak algorithm. Remove the Kconfig
from ARM so that we use the arch_spin_is_contended() definition
from the asm header. This also saves a word in each lock because
we don't need the break_lock member anymore.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VFPv4 support depends on the VFPv3 context save/restore code, so only
advertise support in the hwcaps if the kernel can actually handle it.
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of this warning..
arch/arm/kernel/built-in.o(.text+0xac78): Section mismatch in reference
from the function init_cpu_topology() to the function
.init.text:parse_dt_topology()
The function init_cpu_topology() references
the function __init parse_dt_topology().
This is often because init_cpu_topology lacks a __init
annotation or the annotation of parse_dt_topology is wrong.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GCC built with nonstandard options can enable -fpic by default.
We never want this for 32-bit kernels and it will break the build.
[ hpa: Notably the Android toolchain apparently does this. ]
Change-Id: Iaab7d66e598b1c65ac4a4f0229eca2cd3d0d2898
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Link: http://lkml.kernel.org/r/1344624546-29691-1-git-send-email-andrew.p.boie@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix the wrong logic: we should use || instead of &&
Cc: Leo Yan <leoy@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Yuanhan Liu <yliu.null@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Add the missing usb controller version info and port0, which is
required during setup usb phy.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ntosd2_init_i2c walks the ntosd2_i2c_info array, which it expects to
be populated with at least one member. gcc correctly warns about
the out-of-bounds access here.
Since this can not possibly work, it's better to disable i2c
support entirely on this board.
Without this patch, building davinci_all_defconfig results in:
arch/arm/mach-davinci/board-neuros-osd2.c: In function 'davinci_ntosd2_init':
arch/arm/mach-davinci/board-neuros-osd2.c:187:20: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Andrey Porodko <panda@chelcom.ru>
Disabling CONFIG_BUG creates an insane amount of build warnings, which
makes it useless to check for building defconfigs to see if new
warnings show up.
Without this patch, building tct_hammer_defconfig results in:
net/packet/af_packet.c: In function 'tpacket_rcv':
net/packet/af_packet.c:1889:30: warning: 'hdrlen' may be used uninitialized in this function [-Wuninitialized]
net/core/ethtool.c: In function 'ethtool_get_feature_mask':
net/core/ethtool.c:213:1: warning: control reaches end of non-void function [-Wreturn-type]
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:2914:1: warning: control reaches end of non-void function [-Wreturn-type]
mm/bootmem.c: In function 'mark_bootmem':
mm/bootmem.c:352:1: warning: control reaches end of non-void function [-Wreturn-type]
net/core/dev.c: In function 'skb_warn_bad_offload':
net/core/dev.c:1904:33: warning: unused variable 'null_features' [-Wunused-variable]
drivers/mtd/chips/cfi_probe.c: In function 'cfi_chip_setup':
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
include/linux/mtd/map.h:394:11: note: 'r.x[0]' was declared here
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
(and many more)
The size of vmlinux increases by 1.78% because of this:
size obj-arm/vmlinux.nobug
text data bss dec hex filename
2108474 116916 55352 2280742 22cd26 obj-arm/vmlinux
size obj-arm/vmlinux.bug
text data bss dec hex filename
2150804 116916 53696 2321416 236c08 obj-arm/vmlinux
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.
* testing/new-warnings:
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
exynos_pm_add_dev_to_genpd is used if one or more out of a large
number of Kconfig symbols are enabled. However the new
exynos_defconfig selects none of those, so the function becomes
unused. Marking it so lets the compiler automatically discard
it.
Without this patch, building exynos_defconfig results in:
arch/arm/mach-exynos/pm_domains.c:118:123: warning: 'exynos_pm_add_dev_to_genpd' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
The 4430 OPP table was being registered for all other OMAP4 variants
too, like 4460 and 4470 causing issues with cpufreq driver
enabled. 4460 and 4470 devices have different OPPs as compared to
4430, and they should be populated seperately. As long as that
happens, let the OPP table registeration happen only on 4430 device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 sleep entry code even though itself don't use many CPU registers
makes call to the v7_flush_dcache_all() which uses them. Since
v7_flush_dcache_all() doesn't make use of stack, the caller must take
care of the stack frame. Otherwise it will lead to corrupted stack frame.
Fix it by saving used registers.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not currently possible to build the gpmi-nand driver without
also building the mxs-dma driver. Clarify this Kconfig and enable
both in the defconfig file so we can build it again with both enabled.
drivers/built-in.o: In function `gpmi_dma_filter':
clk-fixed-factor.c:(.text+0xafc18): undefined reference to `mxs_dma_is_apbh'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Without this patch, building integrator_defconfig results in:
arch/arm/mach-integrator/core.c:150:1: warning: data definition has no type or storage class [enabled by default]
arch/arm/mach-integrator/core.c:150:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/arm/mach-integrator/core.c:150:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
The samsung PWM driver has moved to the new PWM subsystem, which
changed the Kconfig symbol for that driver, but the rx1950 and
gta02 boards still uses the old one.
Without this patch, building s3c2410_defconfig results in:
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_lcd_power':
arch/arm/mach-s3c24xx/mach-rx1950.c:430: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:431: undefined reference to `pwm_disable'
arch/arm/mach-s3c24xx/mach-rx1950.c:437: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:438: undefined reference to `pwm_enable'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_exit':
arch/arm/mach-s3c24xx/mach-rx1950.c:504: undefined reference to `pwm_free'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_init':
arch/arm/mach-s3c24xx/mach-rx1950.c:487: undefined reference to `pwm_request'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
The sa1100 definition of the io_p2v macro has changed in v3.6, and this one
file stopped working because of that.
Without this patch, building hackkit_defconfig results in:
arch/arm/mach-sa1100/leds-hackkit.c: In function 'hackkit_leds_event':
arch/arm/mach-sa1100/leds-hackkit.c:39:4: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The EETI touchscreen asserts its IRQ line as soon as it has data in its
internal buffers. The line is automatically deasserted once all data has
been read via I2C. Hence, the driver has to monitor the GPIO line and
cannot simply rely on the interrupt handler reception.
In the current implementation of the driver, irq_to_gpio() is used to
determine the GPIO number from the i2c_client's IRQ value.
As irq_to_gpio() is not available on all platforms, this patch changes
this and makes the driver ignore the passed in IRQ. Instead, a GPIO is
added to the platform_data struct and gpio_to_irq is used to derive the
IRQ from that GPIO. If this fails, bail out. The driver is only able to
work in environments where the touchscreen GPIO can be mapped to an
IRQ.
Without this patch, building raumfeld_defconfig results in:
drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active':
drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-input@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Commit 3d55c29 "ARM: tegra: harmony: add regulator supply name and its
input supply" was supposed to fix all the problems with regulators on
Harmony. However, it appears that I only tested it when booting using
board files, not when booting using device tree. This change fixes two
problems with regulators when booting using device tree:
1) That patch only created the vdd_sys regulator when booting using a
board file. Since this is the root of the whole regulator tree, this
caused no regulators to successfully initialize when booting using
device tree. The registration of vdd_sys is moved to fix this.
2) When booting use DT, the regulator core sets has_full_constraints,
which in turn causes the core to turn off any regulators not marked
as always on. Some of the affected regulators are required for basic
system operation. To solve this, add always on constraints to all
relevant regulators. This doesn't affect booting using a board file
since nothing sets has_full_constraints in that case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The alignment mask is calculated incorrectly. Fixing the calculation
makes strange hangs/lockups disappear during the boot with Amstrad E3
and 3.6-rc1 kernel.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fix dma_contiguous_remap() so that it continues through all the
regions, even after encountering one that is outside lowmem.
Without this change, if you have two CMA regions, the first outside
lowmem and the seocnd inside lowmem, only the second one will get
set up in the MMU. Data written to that region then doesn't get
automatically flushed from the cache into memory.
Signed-off-by: Chris Brand <cbrand@broadcom.com>
[extended patch subject with 'fix' word]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
There are two ports that can output the LCD data, therefore
they have to use separate pimux identifiers so we can select
the one we want to use.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When calling request_irq with IRQF_SHARED, the dev cookie must be set
(i.e. non-NULL), otherwise the code rejects it immediately with -EINVAL.
So restore the logic here where we'd pass a pointer to the name as a
dummy unique val.
Otherwise, booting up on my LANDISK system would fail with:
DMAC Address Error0 request_irq fail
This was introduced in commit 7f47c7189b.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clear AVX, AVX2 features along with clearing XSAVE feature bits,
as part of the parsing "noxsave" parameter.
Fixes the kernel boot panic with "noxsave" boot parameter.
We could have checked cpu_has_osxsave along with cpu_has_avx etc, but Peter
mentioned clearing the feature bits will be better for uses like
static_cpu_has() etc.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1343755754.2041.2.camel@sbsiddha-desk.sc.intel.com
Cc: <stable@vger.kernel.org> # v3.5
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The native 31 bit and the compat behaviour for the mmap system calls differ:
In native 31 bit mode the passed in address for the mmap system call will be
unmodified passed to sys_mmap_pgoff().
In compat mode however the passed in address will be modified with
compat_ptr() which masks out the most significant bit.
The result is that in native 31 bit mode each mmap request (with MAP_FIXED)
will fail where the most significat bit is set, while in compat mode it
may succeed.
This odd behaviour was introduced with d3815898 "[S390] mmap: add missing
compat_ptr conversion to both mmap compat syscalls".
To restore a consistent behaviour accross native and compat mode this
patch functionally reverts the above mentioned commit.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The compat wrappers incorrectly called the non compat versions of
the system process_vm system calls.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are multiple errors in how sys_32_personality() handles personality
flags stored in top three bytes.
- directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.
- directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes
Fix the first one by properly using personality() macro to compare only
PER_MASK bytes.
Fix the second one by setting only the bits that should be set, instead of
overwriting the whole value.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
AM33XX device falls under omap2 class, so make cpu_class_is_omap2()
macro true by adding soc_is_am33xx() to existing list of cpu/soc
check.
This is required to unblock the basic boot support on AM335x platform.
Having done that, we still need to sort out properly from
common zImage point of view without having to maintain this
cpu/soc_is_xxx list.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When only ARCH_OMAP3 (or -2,-4,...) and SOC_AM33XX are selected, multi.h
doesn't set MULTI_OMAP2. In this case, cpu.h will simply define
cpu_is_omap24xx() as 1.
This causes problems for example for omap_hwmod.c:omap_hwmod_init which
checks for cpu_is_omap24xx() first, using the wrong soc_ops for AM33xx.
Fix this by defining MULTI_OMAP2 when using SOC_AM33XX together with
something else.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 350f2f4dad ("[media] v4l: s5p-tv: hdmi: add support for
platform data") makes the presence of platform data mandatory for
s5p-tv driver. Adding an API to plat-samsung for this purpose.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds support for setting HDMI platform data for Exynos4X12 SoCs.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Calling the dmtimer function omap_dm_timer_set_source() fails if following a
call to pm_runtime_put() to disable the timer. For example the following
sequence would fail to set the parent clock ...
omap_dm_timer_stop(gptimer);
omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_32_KHZ);
The following error message would be seen ...
omap_dm_timer_set_source: failed to set timer_32k_ck as parent
The problem is that, by design, pm_runtime_put() simply decrements the usage
count and returns before the timer has actually been disabled. Therefore,
setting the parent clock failed because the timer was still active when the
trying to set the parent clock. Setting a parent clock will fail if the clock
you are setting the parent of has a non-zero usage count. To ensure that this
does not fail use pm_runtime_put_sync() when disabling the timer.
Note that this will not be seen on OMAP1 devices, because these devices do
not use the clock framework for dmtimers.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following sparse warning:
arch/arm/plat-samsung/pm.c:77:21:
warning: symbol 'uart_save' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit d670ac019f (ARM: SAMSUNG: DMA Cleanup as per sparse) changed the
prototype of the s3c2410_dma_* functions to use the enum dma_ch instead
of an generic unsigned int.
In the s3c24xx dma.c s3c2410_dma_enqueue seems to have been forgotten,
the other functions there were changed correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
