While mmc0 enter suspend state, we need halt CQE to send legacy cmd(flush
cache) and disable cqe, for resume back, we enable CQE and not clear HALT
state.
In this case MediaTek mmc host controller will keep the value for HALT
state after CQE disable/enable flow, so the next CQE transfer after resume
will be timeout due to CQE is in HALT state, the log as below:
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: timeout for tag 2
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Caps: 0x100020b6 | Version: 0x00000510
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Config: 0x00001103 | Control: 0x00000001
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: TDL base: 0xfd05f000 | TDL up32: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Doorbell: 0x8000203c | TCN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Task clr: 0x00000000 | SSC1: 0x00001000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQP: 0x00000000 | CRNQDUN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQIS: 0x00000000 | CRNQIE: 0x00000000
This change check HALT state after CQE enable, if CQE is in HALT state, we
will clear it.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Link: https://lore.kernel.org/r/20211026070812.9359-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same calculation to get transfer descriptor offset is already used
at 3 different locations. Let's create a new helper to simplify code.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210521034432.2321-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for eMMC inline encryption using the blk-crypto framework
(Documentation/block/inline-encryption.rst).
eMMC inline encryption support is specified by the upcoming JEDEC eMMC
v5.2 specification. It is only specified for the CQ interface, not the
non-CQ interface. Although the eMMC v5.2 specification hasn't been
officially released yet, the crypto support was already agreed on
several years ago, and it was already implemented by at least two major
hardware vendors. Lots of hardware in the field already supports and
uses it, e.g. Snapdragon 630 to give one example.
eMMC inline encryption support is very similar to the UFS inline
encryption support which was standardized in the UFS v2.1 specification
and was already upstreamed. The only major difference is that eMMC
limits data unit numbers to 32 bits, unlike UFS's 64 bits.
Like we did with UFS, make the crypto support opt-in by individual
drivers; don't enable it automatically whenever the hardware declares
crypto support. This is necessary because in every case we've seen,
some extra vendor-specific logic is needed to use the crypto support.
Co-developed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210125183810.198008-5-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the task descriptor initialization into cqhci_prep_task_desc().
In addition, make it explicitly initialize all 128 bits of the task
descriptor if the host controller is using 128-bit task descriptors,
rather than relying on the implicit zeroing from dmam_alloc_coherent().
This is needed to prepare for CQHCI inline encryption support, which
requires 128-bit task descriptors and uses the upper 64 bits.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-4-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename cqhci.c to cqhci-core.c so that another source file can be added
to the cqhci module without having to rename the module.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-3-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
