The driver was accessing its struct usb_device in its release()
callback without holding a reference. This would lead to a
use-after-free whenever the device was disconnected while the character
device was still open.
Fixes: fef526cae7 ("USB: legousbtower: remove custom debug macro")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch restores the correct DMA mask after switching back to device
mode.
The issue occurred because Device part of controller use 32 bits DMA and
Host side use 64 bits DMA. During loading XHCI driver the DMA mask
used by driver is overwritten by XHCI driver so it must be restored
to 32 bits.
Reported-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/1570449803-15299-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At startup we should trigger the HW state machine
only if it is OTG mode. Otherwise we should just
start the respective role.
Initialize idle role by default. If we don't do this then
cdns3_idle_role_stop() is not called when switching to
host/device role and so lane switch mechanism
doesn't work. This results to super-speed device not working
in one orientation if it was plugged before driver probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20191007121601.25996-2-rogerq@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to disable USB3 PHY for full-speed mode else
gadget mode is broken.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191007121601.25996-3-rogerq@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver bails out at probe if we can't find a bulk-in endpoint or
if we fail to allocate the URB, so drop the check in read().
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver failed to stop its read URB on disconnect, something which
could lead to a use-after-free in the completion handler after driver
unbind in case the character device has been closed.
Fixes: e7389cc9a7 ("USB: skel_read really sucks royally")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was using its struct usb_interface pointer as an inverted
disconnected flag and was setting it to NULL before making sure all
completion handlers had run. This could lead to NULL-pointer
dereferences in the dev_err() statements in the completion handlers
which relies on said pointer.
Fix this by using a dedicated disconnected flag.
Note that this is also addresses a NULL-pointer dereference at release()
and a struct usb_interface reference leak introduced by a recent runtime
PM fix, which depends on and should have been submitted together with
this patch.
Fixes: 4212cd74ca ("USB: usb-skeleton.c: remove err() usage")
Fixes: 5c290a5e42 ("USB: usb-skeleton: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
-----BEGIN PGP SIGNATURE-----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=s9EA
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
max_tu_symbol was programmed to TU_SIZE_RECOMMENDED - 1, which is not
what the spec says. The spec says:
roundup ((input active video bandwidth in bytes/output active video
bandwidth in bytes) * tu_size)
It is not quite clear what the above means, but calculating
max_tu_symbol = (input Bps / output Bps) * tu_size seems to work and
fixes the issues seen.
This fixes artifacts in some videomodes (e.g. 1024x768@60 on 2-lanes &
1.62Gbps was pretty bad for me).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924131702.9988-1-tomi.valkeinen@ti.com
Commit 37db8985b2 ("s390/cio: add basic protected virtualization
support") breaks virtio-ccw devices with VIRTIO_F_IOMMU_PLATFORM for non
Protected Virtualization (PV) guests. The problem is that the dma_mask
of the ccw device, which is used by virtio core, gets changed from 64 to
31 bit, because some of the DMA allocations do require 31 bit
addressable memory. For PV the only drawback is that some of the virtio
structures must end up in ZONE_DMA because we have the bounce the
buffers mapped via DMA API anyway.
But for non PV guests we have a problem: because of the 31 bit mask
guests bigger than 2G are likely to try bouncing buffers. The swiotlb
however is only initialized for PV guests, because we don't want to
bounce anything for non PV guests. The first such map kills the guest.
Since the DMA API won't allow us to specify for each allocation whether
we need memory from ZONE_DMA (31 bit addressable) or any DMA capable
memory will do, let us use coherent_dma_mask (which is used for
allocations) to force allocating form ZONE_DMA while changing dma_mask
to DMA_BIT_MASK(64) so that at least the streaming API will regard
the whole memory DMA capable.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Fixes: 37db8985b2 ("s390/cio: add basic protected virtualization support")
Link: https://lore.kernel.org/lkml/20190930153803.7958-1-pasic@linux.ibm.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The return code from null_handle_zoned() sets the cmd->error value.
Returning OK status when an error occured overwrites the intended
cmd->error. Return the appropriate error code instead of setting the
error in the cmd.
Fixes: fceb5d1b19 ("null_blk: create a helper for zoned devices")
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
The active/pending execlists is no longer protected by the
engine->active.lock, but is serialised by the tasklet instead. Update
the locking around the debug and stats to follow suit.
v2: local_bh_disable() to prevent recursing into the tasklet in case we
trigger a softirq (Tvrtko)
Fixes: df40306902 ("drm/i915/execlists: Lift process_csb() out of the irq-off spinlock")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009160906.16195-1-chris@chris-wilson.co.uk
(cherry picked from commit c36eebd9ba)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Now that we dropped the engine->active.lock serialisation from around
process_csb(), direct submission can run concurrently to the interrupt
handler. As such execlists->active may be advanced as we dequeue,
dropping the reference to the request. We need to employ our RCU request
protection to ensure that the request is not freed too early.
Fixes: df40306902 ("drm/i915/execlists: Lift process_csb() out of the irq-off spinlock")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009100955.21477-1-chris@chris-wilson.co.uk
(cherry picked from commit c949ae4314)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Due to the nature of preempt-to-busy the execlists active tracking and
the schedule queue may become temporarily desync'ed (between resubmission
to HW and its ack from HW). This means that we may have unwound a
request and passed it back to the virtual engine, but it is still
inflight on the HW and may even result in a GPU hang. If we detect that
GPU hang and try to reset, the hanging request->engine will no longer
match the current engine, which means that the request is not on the
execlists active list and we should not try to find an older incomplete
request. Given that we have deduced this must be a request on a virtual
engine, it is the single active request in the context and so must be
guilty (as the context is still inflight, it is prevented from being
executed on another engine as we process the reset).
Fixes: 22b7a426bb ("drm/i915/execlists: Preempt-to-busy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923152844.8914-2-chris@chris-wilson.co.uk
(cherry picked from commit cb2377a919)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We should not remove the workqueue, we just need to ensure that the
workqueues are synced. The workqueues are torn down on ctx removal.
Cc: stable@vger.kernel.org
Fixes: 6b06314c47 ("io_uring: add file set registration")
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we are asked to submit a completed request, just move it onto the
active-list without modifying it's payload. If we try to emit the
modified payload of a completed request, we risk racing with the
ring->head update during retirement which may advance the head past our
breadcrumb and so we generate a warning for the emission being behind
the RING_HEAD.
v2: Commentary for the sneaky, shared responsibility between functions.
v3: Spelling mistakes and bonus assertion
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923110056.15176-3-chris@chris-wilson.co.uk
(cherry picked from commit c0bb487dc1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since amalgamating the queued and active lists in commit 422d7df4f0
("drm/i915: Replace engine->timeline with a plain list"), performing a
i915_request_submit() will remove the request from the execlists
priority queue.
References: 422d7df4f0 ("drm/i915: Replace engine->timeline with a plain list")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923110056.15176-2-chris@chris-wilson.co.uk
(cherry picked from commit 3231f8c011)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The CMP PCH ID we have in the driver is correct for the CML-U machines we have
in our CI system, but the CML-S and CML-H CI machines appear to use a
different PCH ID, leading our driver to detect no PCH for them.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
References: 729ae330a0 ("drm/i915/cml: Introduce Comet Lake PCH")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111461
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190916233251.387-1-matthew.d.roper@intel.com
Fixes: 729ae330a0 ("drm/i915/cml: Introduce Comet Lake PCH")
(cherry picked from commit 8698ba53cd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Use ARRAY_SIZE to caluculate the top of the o32 stack.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Commit ac7c3e4ff4 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of __xchg this would cause to reference function
__xchg_called_with_bad_pointer, which is an error case
for catching bugs and will not happen for correct code, if
__xchg is inlined.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
I hit the following error when compile the kernel.
drivers/iio/light/noa1305.o: In function `noa1305_probe':
noa1305.c:(.text+0x65): undefined reference to `__devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.
Fixes: ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Various minor bug fixes posted in the last couple of weeks:
- Various missed memory frees and error unwind bugs
- Fix regressions in a few iwarp drivers from 5.4 patches
- A few regressions added in past kernels
- Squash a number of races in mlx5 ODP code
-----BEGIN PGP SIGNATURE-----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=sgve
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"The usual collection of driver bug fixes, and a few regressions from
the merge window. Nothing particularly worrisome.
- Various missed memory frees and error unwind bugs
- Fix regressions in a few iwarp drivers from 5.4 patches
- A few regressions added in past kernels
- Squash a number of races in mlx5 ODP code"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Add missing synchronize_srcu() for MW cases
RDMA/mlx5: Put live in the correct place for ODP MRs
RDMA/mlx5: Order num_pending_prefetch properly with synchronize_srcu
RDMA/odp: Lift umem_mutex out of ib_umem_odp_unmap_dma_pages()
RDMA/mlx5: Fix a race with mlx5_ib_update_xlt on an implicit MR
RDMA/mlx5: Do not allow rereg of a ODP MR
IB/core: Fix wrong iterating on ports
RDMA/nldev: Reshuffle the code to avoid need to rebind QP in error path
RDMA/cxgb4: Do not dma memory off of the stack
RDMA/cm: Fix memory leak in cm_add/remove_one
RDMA/core: Fix an error handling path in 'res_get_common_doit()'
RDMA/i40iw: Associate ibdev to netdev before IB device registration
RDMA/iwcm: Fix a lock inversion issue
RDMA/iw_cxgb4: fix SRQ access from dump_qp()
RDMA/hfi1: Prevent memory leak in sdma_init
RDMA/core: Fix use after free and refcnt leak on ndev in_device in iwarp_query_port
RDMA/siw: Fix serialization issue in write_space()
RDMA/vmw_pvrdma: Free SRQ only once
cleanup error handling code and make sure temporary info array
with the handles are freed by amdgpu_bo_list_put() on
idr_replace()'s failure.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Numerous fixes to the compat vDSO build system, especially when
combining gcc and clang
- Fix parsing of PAR_EL1 in spurious kernel fault detection
- Partial workaround for Neoverse-N1 erratum #1542419
- Fix IRQ priority masking on entry from compat syscalls
- Fix advertisment of FRINT HWCAP to userspace
- Attempt to workaround inlining breakage with '__always_inline'
- Fix accidental freeing of parent SVE state on fork() error path
- Add some missing NULL pointer checks in instruction emulation init
- Some formatting and comment fixes
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl2dv4cQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNO6UB/4yY3lYR6C++7EdVwYxQRXf8VX9ukeO76gp
P/AS6Kt8+AiOuhFJJXDj3D7K/KqgZnJEhzeWHTZluYpIBuzFerW+RxzmExL+wFWf
ISZgdh7roFCQx3Nt+iBs/bAMPvk5Da1KHvSw/yZ6P8mj6fK8sVUh/O8+KK4kSzfT
muDoSO6WHSonAEOYm9ryn1q1pM5DsCjr+9fm7d9L+dJAUP2xX44ymlIY+v6yD3Or
IWJMYaWKb4TbdTJSy2VbUSM0fzByGBJCx1wOTd4gV6uDbB4GA6h+E/DMB1qnvv9W
nH5c4qwVgYhp7prpescMxYZoV/I9damvfnaIjqh9jc3H3milEqcn
=GwLJ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A larger-than-usual batch of arm64 fixes for -rc3.
The bulk of the fixes are dealing with a bunch of issues with the
build system from the compat vDSO, which unfortunately led to some
significant Makefile rework to manage the horrible combinations of
toolchains that we can end up needing to drive simultaneously.
We came close to disabling the thing entirely, but Vincenzo was quick
to spin up some patches and I ended up picking up most of the bits
that were left [*]. Future work will look at disentangling the header
files properly.
Other than that, we have some important fixes all over, including one
papering over the miscompilation fallout from forcing
CONFIG_OPTIMIZE_INLINING=y, which I'm still unhappy about. Harumph.
We've still got a couple of open issues, so I'm expecting to have some
more fixes later this cycle.
Summary:
- Numerous fixes to the compat vDSO build system, especially when
combining gcc and clang
- Fix parsing of PAR_EL1 in spurious kernel fault detection
- Partial workaround for Neoverse-N1 erratum #1542419
- Fix IRQ priority masking on entry from compat syscalls
- Fix advertisment of FRINT HWCAP to userspace
- Attempt to workaround inlining breakage with '__always_inline'
- Fix accidental freeing of parent SVE state on fork() error path
- Add some missing NULL pointer checks in instruction emulation init
- Some formatting and comment fixes"
[*] Will's final fixes were
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
but they were already in linux-next by then and he didn't rebase
just to add those.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (21 commits)
arm64: armv8_deprecated: Checking return value for memory allocation
arm64: Kconfig: Make CONFIG_COMPAT_VDSO a proper Kconfig option
arm64: vdso32: Rename COMPATCC to CC_COMPAT
arm64: vdso32: Pass '--target' option to clang via VDSO_CAFLAGS
arm64: vdso32: Don't use KBUILD_CPPFLAGS unconditionally
arm64: vdso32: Move definition of COMPATCC into vdso32/Makefile
arm64: Default to building compat vDSO with clang when CONFIG_CC_IS_CLANG
lib: vdso: Remove CROSS_COMPILE_COMPAT_VDSO
arm64: vdso32: Remove jump label config option in Makefile
arm64: vdso32: Detect binutils support for dmb ishld
arm64: vdso: Remove stale files from old assembly implementation
arm64: vdso32: Fix broken compat vDSO build warnings
arm64: mm: fix spurious fault detection
arm64: ftrace: Ensure synchronisation in PLT setup for Neoverse-N1 #1542419
arm64: Fix incorrect irqflag restore for priority masking for compat
arm64: mm: avoid virt_to_phys(init_mm.pgd)
arm64: cpufeature: Effectively expose FRINT capability to userspace
arm64: Mark functions using explicit register variables as '__always_inline'
docs: arm64: Fix indentation and doc formatting
arm64/sve: Fix wrong free for task->thread.sve_state
...
The callers of xfs_bmap_local_to_extents_empty() log the inode
external to the function, yet this function is where the on-disk
format value is updated. Push the inode logging down into the
function itself to help prevent future mistakes.
Note that internal bmap callers track the inode logging flags
independently and thus may log the inode core twice due to this
change. This is harmless, so leave this code around for consistency
with the other attr fork conversion functions.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_attr_shortform_to_leaf() attempts to put the shortform fork back
together after a failed attempt to convert from shortform to leaf
format. While this code reallocates and copies back the shortform
attr fork data, it never resets the inode format field back to local
format. Further, now that the inode is properly logged after the
initial switch from local format, any error that triggers the
recovery code will eventually abort the transaction and shutdown the
fs. Therefore, remove the broken and unnecessary error handling
code.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
When a directory changes from shortform (sf) to block format, the sf
format is copied to a temporary buffer, the inode format is modified
and the updated format filled with the dentries from the temporary
buffer. If the inode format is modified and attempt to grow the
inode fails (due to I/O error, for example), it is possible to
return an error while leaving the directory in an inconsistent state
and with an otherwise clean transaction. This results in corruption
of the associated directory and leads to xfs_dabuf_map() errors as
subsequent lookups cannot accurately determine the format of the
directory. This problem is reproduced occasionally by generic/475.
The fundamental problem is that xfs_dir2_sf_to_block() changes the
on-disk inode format without logging the inode. The inode is
eventually logged by the bmapi layer in the common case, but error
checking introduces the possibility of failing the high level
request before this happens.
Update both of the dir2 and attr callers of
xfs_bmap_local_to_extents_empty() to log the inode core as
consistent with the bmap local to extent format change codepath.
This ensures that any subsequent errors after the format has changed
cause the transaction to abort.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We no longer need the extra mirror length tracking in the O_DIRECT code,
as we are able to track the maximum contiguous length in dreq->max_count.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When a series of O_DIRECT reads or writes are truncated, either due to
eof or due to an error, then we should return the number of contiguous
bytes that were received/sent starting at the offset specified by the
application.
Currently, we are failing to correctly check contiguity, and so we're
failing the generic/465 in xfstests when the race between the read
and write RPCs causes the file to get extended while the 2 reads are
outstanding. If the first read RPC call wins the race and returns with
eof set, we should treat the second read RPC as being truncated.
Reported-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Fixes: 1ccbad9f9f ("nfs: fix DIO good bytes calculation")
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
It turns out that the NMI latency workaround from commit:
6d3edaae16 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")
ends up being too conservative and results in the perf NMI handler claiming
NMIs too easily on AMD hardware when the NMI watchdog is active.
This has an impact, for example, on the hpwdt (HPE watchdog timer) module.
This module can produce an NMI that is used to reset the system. It
registers an NMI handler for the NMI_UNKNOWN type and relies on the fact
that nothing has claimed an NMI so that its handler will be invoked when
the watchdog device produces an NMI. After the referenced commit, the
hpwdt module is unable to process its generated NMI if the NMI watchdog is
active, because the current NMI latency mitigation results in the NMI
being claimed by the perf NMI handler.
Update the AMD perf NMI latency mitigation workaround to, instead, use a
window of time. Whenever a PMC is handled in the perf NMI handler, set a
timestamp which will act as a perf NMI window. Any NMIs arriving within
that window will be claimed by perf. Anything outside that window will
not be claimed by perf. The value for the NMI window is set to 100 msecs.
This is a conservative value that easily covers any NMI latency in the
hardware. While this still results in a window in which the hpwdt module
will not receive its NMI, the window is now much, much smaller.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 6d3edaae16 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In perf_rotate_context(), when the first cpu flexible event fail to
schedule, cpu_rotate is 1, while cpu_event is NULL. Since cpu_event is
NULL, perf_rotate_context will _NOT_ call cpu_ctx_sched_out(), thus
cpuctx->ctx.is_active will have EVENT_FLEXIBLE set. Then, the next
perf_event_sched_in() will skip all cpu flexible events because of the
EVENT_FLEXIBLE bit.
In the next call of perf_rotate_context(), cpu_rotate stays 1, and
cpu_event stays NULL, so this process repeats. The end result is, flexible
events on this cpu will not be scheduled (until another event being added
to the cpuctx).
Here is an easy repro of this issue. On Intel CPUs, where ref-cycles
could only use one counter, run one pinned event for ref-cycles, one
flexible event for ref-cycles, and one flexible event for cycles. The
flexible ref-cycles is never scheduled, which is expected. However,
because of this issue, the cycles event is never scheduled either.
$ perf stat -e ref-cycles:D,ref-cycles,cycles -C 5 -I 1000
time counts unit events
1.000152973 15,412,480 ref-cycles:D
1.000152973 <not counted> ref-cycles (0.00%)
1.000152973 <not counted> cycles (0.00%)
2.000486957 18,263,120 ref-cycles:D
2.000486957 <not counted> ref-cycles (0.00%)
2.000486957 <not counted> cycles (0.00%)
To fix this, when the flexible_active list is empty, try rotate the
first event in the flexible_groups. Also, rename ctx_first_active() to
ctx_event_to_rotate(), which is more accurate.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <kernel-team@fb.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 8d5bce0c37 ("perf/core: Optimize perf_rotate_context() event scheduling")
Link: https://lkml.kernel.org/r/20191008165949.920548-1-songliubraving@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
