This patch fixes two different problems.
1) The port VLAN configuration was not persistent across VF driver
loads and unloads.
2) The port VLAN configuration was only correct the first time it was
set. Switching the port VLAN on and off would cause subsequent VLAN
configurations to be corrupted in the VSI. Ensure that the correct
bits are being set for the VSI port VLAN configuration.
Change-Id: I7ebf5329f77eb8d73ccd3324eb346b3abeea737d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save information that we can use while cleaning the tx ring. Also record
the time_stamp since we will need it to check tx hangs.
Change-Id: Ia3f1c17f6fec9bcb7fef2542d77eac7f6c4f115c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to clean PBA only when interrupts are turned off and we
are polling instead.
Change-Id: Ic0c1da761bd3abe7f73b1cc8bcddf8e3a232fd0f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions don't need a prototype as they are defined
in the file before they are called.
Change-Id: Ie17ffad4a29a9c0df434c4ebc4681128a6095c65
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove references to I40E_FLAG_MQ_ENABLED from the code
as it doesn't seem to be used anywhere.
Change-Id: I4c89fb65b2cdd26fbb0c58fccbbb4b03f0e5f1b3
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The allocation and clearing of rings for a VSI should be
using the alloc_queue_pairs and not num_queue_pairs.
The alloc_queue_pairs per VSI is a pre-allocated number
of queues assigned to a VSI; based on number of TCs enabled
only certain number of queues may be used from that. This
is mainly valid only for the LAN VSI case as that is the
only VSI that may be enabled with multiple traffic classes.
In the future the number of TCs may change based on DCBX
configuration.
The actual number of queues that are enabled/configured is
based on the number of TCs enabled for a given VSI and that
is stored in num_queue_pairs.
With this change num_[tr]x_queues is unused so remove them.
Change-Id: I9c2f84778bb25f7313c630e9b002a0caa883ce29
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't try to free a q_vector that hasn't been set up as it can
panic the kernel.
Change-Id: I0650cc6c441d0779788c522c790293c276d14fbc
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save both a pointer to memory and the length in order to store all
info about allocated kernel memory. This patch changes some adminq
allocations to preserve the full i40e_dma_mem/i40e_virt_mem structs
for every allocation.
Change-Id: Ibcf96159aba4ba61f839d16d87d19478df28e630
Signed-off-by: David Cassard <david.g.cassard@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Swap a couple lines around in the error handling if the kzalloc() for
the pf->vsi array fails. This was causing a kernel BUG because the
call to i40e_clear_interrupt_scheme() was assuming the pf->vsi[] array
existed. In this fix it is possible that i40e_reset_interrupt_capability()
will get called twice, but this is a safe action.
Change-Id: I939163ccaa89baac7511556d36bc873864c35ae1
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning the ARQ, we must reinitialize the buffer size each time we
go through the loop, because i40e_clean_arq_element returns the message
length in the same field. Without this change, subsequent messages can
be truncated to the length of the previous message.
Change-Id: Ic9c32ff843faf0fc3196d21351a1c3a60c6158eb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce i40e_irq_dynamic_disable_icr0 and use it and its previously-
extant counterpart when appropriate.
Change-Id: Ieb4037874fba2e96fc2354b34a97a3cb8f6490f3
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an include header guard to guard against multiple includes
Change-Id: I73efa03efc912d2047edab903c7caed05b444da2
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When disabling and enabling VFs on a live system with the VF driver
loaded, it's possible to receive an admin queue message from the VF
driver at an inconvenient time, e.g. when the associated data structures
aren't present or configured. This causes a rather inconvenient panic.
To guard against this, we change the order of when we set num_alloc_vfs
when turning off SR-IOV, and then gate processing of any VF messages
based upon that value. Likewise, when enabling VFs, we shut off the
relevant interrupt until configuration is complete.
Change-Id: I0c172c056616c2bebd78bbc807ab446eb484deea
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Earlier we were reading Shadow RAM (copy of the NVM) which can differ
from the actual NVM. Use AQ instead to read the actual NVM.
Change-Id: Ia0f2773b722db77d093f738c068af872be69bbd4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove custom i40e functions around ethernet addresses that are
duplicating already existing kernel functionality.
Also ends up fixing a bug with multicast addresses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Debugfs was reading exactly half the number of words, fix it.
Change-Id: Ieb217f3c6dca455d44e50a0dc61a6664c0cb2265
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the user does not assign a VF MAC address, then just report it as
zero. Attempting to guess the correct primary MAC address of the VF is a
futile and heartbreaking endeavour.
Change-Id: I2673577a160afb6fc55094c890467b44e60c7584
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an argument to led function and refactor code to flash LED lights
correctly.
Change-Id: I00b21607ced53aaa057159503875708871946259
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make a define used in the header file by both VF and PF drivers.
Change-Id: Ie9e35adcc021cd6a8f7513934984eb4ed55774f5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF sends a bad message, be more informative about what it
actually is.
Change-Id: I89e06d2db416a1d05aeea016dd6e8b7870cae99a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF asks to add an invalid MAC address, tell it that instead of
just using a generic return code.
Change-Id: I366aff5449fa5874ad51e2734cac2a71783ab14b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't complain when we disable queues that are already disable, or
enable them when they're already enabled. This removes a bunch of bogus
log messages that we see at every VF reset.
Change-Id: Ia127be572abdccc48a53d8c43f8a07b8bb920de1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't keep separate functions to enable and disable queues for the VFs.
Just call the existing function that everybody else uses. Remove the
unused functions.
Change-Id: I15db9aad64a59e502bfe1e0fdab9b347ab85c12c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the VF reset flow so that it works on real hardware. After
discussions with the HW team, the reset flow has been changed
somewhat.
- Change the i40e_reset_vf function to a void type, and fix
up the callers to reflect this.
- Move the MSI-X disable code to i40e_free_vf_res since it must
be done every time the VF is freed, regardless of whether or
not it is reset.
- Ensure that the PCIe bus is quiet before polling the reset bit.
- Don't clear the VFGEN_RSTAT1 register at the beginning as it is
cleared by the reset.
- Poll longer for the reset to be done.
- Disable the queues using an existing function rather than
rolling our own.
- Free and reallocate the VSI after reset to avoid rx hang.
Change-Id: I11e2590431cb73e8663714d1cc5b23d59b809033
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF reset code will be refactored in future patches. Part of that
refactor required it to call i40e_alloc_vf_res and i40e_free_vf_res, so
the function must be moved. In order to make the future patches more
readable, we perform the function move here, with no other changes.
Change-Id: If6567c9c0bada6caafb2ee0227e0d9d50d05f27f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements receive offload for VXLAN for i40e. The hardware
supports checksum offload/verification of the inner/outer header.
Change-Id: I450db300af6713f2044fef1191a0d1d294c13369
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the implementation for the VXLAN ndo's. This allows the
hardware to do RX checksum offload for inner packets on the UDP ports
that VXLAN notifies us about.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add curly-braces on a multi-line function. While we're here we
also change to return void in i40e_vsi_clear_rings() since no
caller cares.
Change-Id: I261fcef20e2a39e18d83ec08fdd14456131dee91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wake on LAN is disabled by default and will remain that way for most
platforms, but there is an NVM setting that allows vendors to enable it
for a port if they think they've provided the right power environment
for the device. This patch adds code to check the NVM setting and enable
Magic Packet use if WoL is enabled for the port.
Since only Magic Packet is supported, there's not a lot of HW configuration
needed.
Change-Id: I44e904a7b15695e34683009f487064cd86ea59b0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call i40e_set_pci_config_data from probe, then check that
we are in a 8GT/s x8 PCIe slot and send a warning if we are not.
Change-Id: I62815c574cee50d2787c50bbe956dde7a7a75a11
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HMC error interrupt would generate an un-necessary message
"unhandled interrupt", causing extra log spam, in addition to causing
a reset that was not necessary. Prevent this issue by handling the
HMC error case explicitly, and only reset if the interrupt was from
some of the other causes.
Change-Id: Iabd203ba1dfc26a136b638597f3e9991acfa29f3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using for_each_set_bit() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions static in the file they are used.
Remove functions i40e_aq_add_vlan and i40e_aq_remove_vlan since
they are not used anywhere by current code.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We assume that the resulting buffer is zero terminated when we then
re-use it. The sscanf is limited to 512 bytes but needs to be 511
to allow for a terminator.
One of a set of problems noted by Jackie Chang
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Shannon Nelson <Shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No functional change, but the wrong defines were being used.
Change-Id: Ica2afd2dfe18154ca0f1260a508f31e372319ba7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take advantage of print_hex_dump() in another couple places to
clean up the code.
Change-Id: Ib618e75f928308c0afd0d8d74105da0c6577a024
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up a couple of scanfs to accept various base numbers instead of silently
requiring hex.
Change-Id: I1cc4dffbb1d011bf603cbf34a8db093da57fad7a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
debugfs fixes: We don't really need to give usage messages for data errors,
only for invalid command errors.
Change-Id: If3f74ac49e43c3ced7fd388323fa738ac145e055
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check that rings were allocated before trying to reference them.
Change-Id: I33151e55ab7a7a305fecdb88ccb2709ac246b7c7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The debugfs commands that dump hex information are not doing these as
expected viz. "lldp get local", "nvm read", "dump debug fwdata", etc.
Use print_hex_dump() instead to hex dump and remove the print buffer
stuff from the code.
Change-Id: I507bd8b2187aae8bad5055b7872978c309cf143e
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove FCoE code from the VF interface, as the feature will
not be supported on VF interfaces.
Change-Id: Ie9db04fa2e37fa14ac3e73a9c20980348d931357
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Any user-initiated path which eventually calls reset needs
to hold the rtnl_lock, so add functionality to do that.
Be careful not to use the safe reset when cleaning up
from the diagnostic tests, which avoids rtnl_lock
recursion from ethtool.
Protect the reset_task with rtnl_lock, since it runs from a work item.
Change-Id: Ib6e7a3fb2966809db2daf35fd5a123ccdf6f6f0f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the number of receive/transmit queue pair being
changed on the fly by ethtool.
Change-Id: I70df2363f1ca40b63610baa561c5b6b92b81bca7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the second of 3 patches that allows for changing
the number of queues in the driver on the fly.
This patch adds a function that calls the reinit flow for the
main VSI after making changes to the RSS queue count as requested
by the user.
Change-Id: I82dee91e9fe90eeb4e84a7369f4b8b342155dd85
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is the first in a 3 series patchset to implement
dynamically changing the queue count for the main VSI.
This patch starts by adding a reinit flow. This flow is designed
to be able to change just the queue count and not the number of
interrupt vectors that the device originally came up with.
Change-Id: I0634aaebf7dc4dd6c66af8f9dbbef89d7beac438
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current driver default sets the number of transmit/receive
queue pairs based on the current node's CPU count.
A better method is to use the total number of CPUs in the system
to suggest the number of queue pairs, which aligns better with
the behavior of ixgbe, and also with the expectations of the
kernel XPS and other subsystems in the stack.
Change-Id: If3e20c7f100f13e51d69762594d948f247ffe0c8
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent some compiler warnings and implement some other
trivial fixes.
Change-Id: I7f49d79b91b94df1ad4a8306a0410ed72238845f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor flow control set up and disable L2 flow
control by default.
Change-Id: I2fe257b80df6d9a1e37deb4df118da8f8467040d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call the netif_set_real* functions in order to make sure
the stack knows about how many queues we have, in order
for RFS/RPS/XFS to work correctly.
Change-Id: Ib7a7b2792f80c5eef210dedf42cc6607d63953d2
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the ethtool testing starts it sets the I40E_TESTING state
bit, which blocks new netdev opens so that things don't get
confused, while the testing might be messing with register and
other things. Unfortunately, that was keeping the PF resets
after the register test from working correctly because the netdev
would not get reopened. This patch reorders the tests to put the
register test last as it is the only one that needs a reset, and
we wait to trigger the reset until after we clear the
I40E_TESTING bit.
Change-Id: Ieaa18d74264250ac336b0656b490125ee8a22d2a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Get some more reasonable information reported back out to ethtool
for the different types of connections supported.
Change-Id: I57b153f86b9cdd04ad7cb5bf7d1c45873c196a7a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the vsi->tx_rings structure is NULL we don't want to panic.
Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I40E_ITR_NONE was being used as an ITRN register index by
accident because it was easily associated with the I40E_RX_ITR
and friends defines.
Change the name slightly in order to make it clear that
I40E_ITR_NONE is really associated with the DYN_CTL register
sets.
Change-Id: I04702c027c7495b90a8bf2db85d3e085a2c7d02a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of silently clamping the descriptor change request into
the proper range, fail the request and complain in the log file.
Change-Id: Id55ef59255d93c04bedffa8e25fe7ea796c90f32
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add information about current loopback mode to data returned from
get_link_info function. Minor fix in set_loopback function and
update in loopback types enum.
Change-Id: I9d1c540a84ab18eef5ea6429be6331f33fc06aca
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the netif_info() macro to restrict messaging to when the HW
bit is enabled in the msglvl netdev message mask.
Change-Id: I83030d4402991cfb7da100da00f05ce502ada4ae
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Track the number of physical functions (PFs) found, this is a global counter
on purpose so that each pf loaded has a unique ID.
Change-Id: I74d618520afbce4a774d0235449e3b5f97ff6d4a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print a message to notify the user of how many VFs are initialized on each
port.
Change-Id: I29ac2acc478ee4e588fd6ffcc35133d4c6607ca9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Put the print and reset statements in the actual test functions to make
them more self-contained, and only run the reset for tests that need it.
Change-Id: Ic70f49b11bf8bae82e59d8fd25b46215c90c4510
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where the TESTING state was still set when
exiting the ethtool diagnostics.
Change-Id: Ic47950d2e86a67167d1d282256d477cecd86d820
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VSI may be allocated more queues (alloc_queue_pairs) than actually
are to be used (num_queue_pairs), so only allocate rings for the queues
to be used. The numbers will likely be the same for most VSIs, but can
be different based on how TCs are assigned and enabled.
Change-Id: Ie40f7ad0affbc4b45d6f049bcf02ee2fa24edc74
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS can steer packets based on recognition of all
sorts of different headers. Enable some more of them.
Change-Id: I2264dedae66fb0bceca6fb6e772e050e3ca8efc8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to re-size queues and vectors while the interface is
still up, we need to be able to call functions to free and
re-allocate without bringing down the VSI.
We also need to reset the existing setup, update the
configuration and then rebuild again. This requires us to have
the reset flow broken down into two parts.
Change-Id: I374dd25aabf769decda69b676491c7b7730a4635
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable a couple of workarounds based on revision ID that allow the
driver to work more fully on early hardware.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new flag to the add VEB command which allows the
driver to request the hardware to filter on L2 parameters.
This is an implementation of the driver access to a new firmware
feature.
Change-Id: Id61d3cad4125bdc68b8fd9d555c448a10c344b6b
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the media type in the hardware structure, based
on the external connection type.
Add Direct Attach to the type of media reported by ethtool.
Change-Id: I4ad2f5bf882766d6e737fac4477abf049491b3b3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hash is reported correctly in the rss field if and only if
the filter status is 3. Other values of filter status mean
different things and we shouldn't depend on a bitwise result.
The issue was that
a & b --> returns true for b={1,2,3}
the fix is
a & b == b
Also refactor this function to use constant operations because we
are in fast path.
Change-Id: I4e29be87439c1cf8b60bc31bea29dff89596c013
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to get 1588 to work correctly the defines need a bit
of a tweak.
Change-Id: Ie50ce2a18e1593441f1560411e5a4f51c6d48aaa
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The diagnostics test needs some slightly different limits
in order to succeed.
Change-Id: Ia1c49148af92fa4be20778a819f69350381bf865
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a quick ethtool test for interrupts using the SW interrupt.
Also, change the loopback test (for now) to not report failure.
Change-Id: Id8ef154b82475e3163087a8d1df01dfec4d529fc
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the debug mask by default.
Change-Id: I10346ccb1a47f79747eb2108a83af059e947f1e2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up some messages that had arguments reversed.
Change-Id: I0f38a4f01132a2918d61dbaf23de1e1eaed5e56d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code that added new MAC addresses from the VFs did not, in
fact, work. Due to inverse logic, the only addresses that could
be added were addresses that already had been added.
Change-Id: Idce9169bd2f36e2c5ee10b130587a65705465d31
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the admin queue times out, retry some more to make driver load and
reset more robust.
Change-Id: I45c977b3d10a62c770d6072659ec27834849ca33
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The indication for telling which reset happened is a value, not a
bit pattern, so select by ==, not &.
Change-Id: Ie04097388ff16b85015d6ab1236d7511ef653e8c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of vectors per VF as reported by the hardware does not
include vector 0, so we need to account for this when checking to
see if the VF is configuring a valid vector.
Change-Id: I051d8bebae8f4722239f5a3fa5e1de4cf0f4e817
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The version bits reported by the hardware changed, so fix
up the offsets to print the version correctly.
Change-Id: I8a8207b401ea88f6da024aebafe7d3826ee6512c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware definitions changed slightly so sync up the defines
file with the updated state of the hardware.
Change-Id: I8349d91630a3208df306bd1dc88f028c87be2248
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
pf_id needs to be encoded for cards with ARI enabled, which
allows for larger function numbers than 8.
Commit-Id: I23fa7df9dabf3878cc08c9b2151729c8539f5f17
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix to return -ENOMEM in the memory alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simplify code by using an already existing variable.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure there really are rings and queues before trying to dump
information in them.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a cleanup of the local variables declared at the beginning
of each function.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the overactive irq issue seen in testing and allow use of
the legacy interrupt.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function did a lot of unnecessary cpu_to_xxx(foo) and making it
worse, each of these calls caused a lot of line wrapping.
Fix look and feel via a refactor of this function. No functional
changes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a fix for an issue reported by coverity, reported
by Hannes Frederic Sowa.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a fix for an issue reported by coverity, reported by
Hannes Frederic Sowa.
I'm unable to test if this patch actually fixes the coverity
reported issue, feedback is welcome.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This issue was identified by the coverity checker where we were
not checking the upper limit on reads, reported by Hannes
Frederic Sowa.
Implement more specific limits on reads (min 1k, max 4k)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
debugfs fixes for issues found by coverity.
This issue was identified by the coverity checker, reported by Hannes Frederic
Sowa.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were a number of little bugs in the error handling of irq setup, most of
which ended up panicing the kernel, and are addressed by this patch, along with
a couple formatting issues.
Legacy interrupts (including MSI) are used only in the case of failure to
allocate MSI-X interrupts.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct math error when assigning MSI-X vectors to VFs. The vectors-per-vf
value reported by the hardware already conveniently reports one less than the
actual value.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Not all VSIs have rings! Check to see if rings were actually allocated before
freeing them.
This prevents a panic when tx_rings[0] is not allocated.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hot path doesn't need read-flush after interrupt enable, and this
flush really causes a lot of extra cpu utilization.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the version number of the driver.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change brings support for 64 bit netstats to the driver. Previously
the stats were 64 bit but highly racy due to the fact that 64 bit
transactions are not atomic on 32 bit systems. This change makes is so
that the 64 bit byte and packet stats are reliable on all architectures.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate the queue pairs individually instead of as a group. This
allows for much easier queue management as it is possible to dynamically
resize the queues without having to free and allocate the entire block.
Ease statistic collection by treating Tx/Rx queue pairs as a single
unit. Each pair is allocated together and starts with a Tx queue and
ends with an Rx queue. By ordering them this way it is possible to know
the Rx offset based on a pointer to the Tx queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This replaces the ring container array with a linked list. The idea is
to make the logic much easier to deal with since this will allow us to
call a simple helper function from the q_vectors to go through the
entire list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate the q_vectors individually. The advantage to this is that it
allows for easier freeing and allocation. In addition it makes it so
that we could do node specific allocations at some point in the future.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This makes it so that the Tx and Rx byte and packet counts are
separated from the rest of the statistics. This allows for better
isolation of these stats when we move them into the 64 bit statistics.
Simplify things by re-ordering how the stats display in ethtool.
Instead of displaying all of the Tx queues as a block, followed by all
the Rx queues, the new order is Tx[0], Rx[0], Tx[1], Rx[1], ..., Tx[n],
Rx[n]. This reduces the loops and cleans up the display for testing
purposes since it is very easy to verify if flow director is doing the
right thing as the Tx and Rx queue pair are shown in pairs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop Tx flag and TXSW which is tested but never set.
As a result of this change we can drop a complicated check that always
resulted in the final result of i40e_tx_csum being equal to the
CHECKSUM_PARTIAL value. As such we can replace the entire function call
with just a check for skb->summed == CHECKSUM_PARTIAL.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sync the fast path for i40e_tx_map and i40e_clean_tx_irq so that they
are similar to igb and ixgbe.
- Only update the Tx descriptor ring in tx_map
- Make skb mapping always on the first buffer in the chain
- Drop the use of MAPPED_AS_PAGE Tx flag
- Only store flags on the first buffer_info structure
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid directly incrementing next_to_use for multiple reasons. The main
reason being that if we directly increment it then it can attain a state
where it is equal to the ring count. Technically this is a state it
should not be able to reach but the way this is written it now can.
This patch pulls the value off into a register and then increments it
and writes back either the value or 0 depending on if the value is equal
to the ring count.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- drop the mapped_as_page u8 from the Tx buffer info as it was unused
- use the DMA unmap accessors for Tx DMA
- replace checks of DMA with checks of the unmap length to verify if an
unmap is needed
- update the Tx buffer layout to make it consistent with igb, ixgbe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx "completed" stat was part of the original rewrite for detecting
Tx hangs. However some time ago in ixgbe I determined that we could
just use the packets stat instead. Since then this stat was
removed from ixgbe and it serves no purpose in i40e so it can be
dropped.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link events should not print to the log until the device is
administratively up.
Signed-off-by: Anjali Singhai <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
coccicheck shows:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment
Fix each of them with a *a = *b;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.
A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.
v2: fix post increment bug in return
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.
This allows for clean up of the return types that were previously
converted to int.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches clean up a loop flow.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, we should be using
foo = alloc(...)
if (!foo)
return -ENOMEM;
return 0;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the changes for Kconfig, i40e.txt, MAINTAINERS, Kbuild
and new i40e/Makefile to build i40e with the kernel.
New driver build option is CONFIG_I40E
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver includes a debugfs interface for developers to get more hardware
information in real-time.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While not part of this patch series, an i40evf driver is on its
way, and uses these files to communicate to the PF driver.
This patch contains the header and implementation files for the
PF to VF interface.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the main driver header files, containing
structures and data types specific to the linux driver.
i40e_osdep.h contains some code that helps us adapt our OS agnostic code to
Linux.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the ethtool interface and implementation.
The goal in this patch series is minimal functionality while not
including much in the way of "set support."
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the transmit, receive, and NAPI routines, as well
as ancillary routines.
This file is code that is (will be) used by both the VF and PF
drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the driver for the Intel(R) Ethernet Controller XL710 Family.
This driver is targeted at basic ethernet functionality only, and will be
improved upon further as time goes on.
This patch contains the driver entry points but does not include transmit
and receive (see the next patch in the series) routines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
