Reproduce environment:
network with 3 VM linuxs is connected as below:
VM1<---->VM2(latest kernel 6.5.0-rc7)<---->VM3
VM1: eth0 ip: 192.168.122.207 MTU 1800
VM2: eth0 ip: 192.168.122.208, eth1 ip: 192.168.123.224 MTU 1500
VM3: eth0 ip: 192.168.123.240 MTU 1800
Reproduce:
VM1 send 1600 bytes UDP data to VM3 using tools scapy with flags='DF'.
scapy command:
send(IP(dst="192.168.123.240",flags='DF')/UDP()/str('0'*1600),count=1,
inter=1.000000)
Result:
Before IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqdss
Ip: 1 64 6 0 2 2 0 0 2 4 0 0 0 0 0 0 0 0 0
......
root@qemux86-64:~#
----------------------------------------------------------------------
After IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqdss
Ip: 1 64 7 0 2 2 0 0 2 5 0 0 0 0 0 0 0 1 0
......
root@qemux86-64:~#
----------------------------------------------------------------------
ForwDatagrams is always keeping 2 without increment.
Issue description and patch:
ip_exceeds_mtu() in ip_forward() drops this IP datagram because skb len
(1600 sending by scapy) is over MTU(1500 in VM2) if "DF" is set.
According to RFC 4293 "3.2.3. IP Statistics Tables",
+-------+------>------+----->-----+----->-----+
| InForwDatagrams (6) | OutForwDatagrams (6) |
| V +->-+ OutFragReqds
| InNoRoutes | | (packets)
/ (local packet (3) | |
| IF is that of the address | +--> OutFragFails
| and may not be the receiving IF) | | (packets)
the IPSTATS_MIB_OUTFORWDATAGRAMS should be counted before fragment
check.
The existing implementation, instead, would incease the counter after
fragment check: ip_exceeds_mtu() in ipv4 and ip6_pkt_too_big() in ipv6.
So do patch to move IPSTATS_MIB_OUTFORWDATAGRAMS counter to ip_forward()
for ipv4 and ip6_forward() for ipv6.
Test result with patch:
Before IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqdss
Ip: 1 64 6 0 2 2 0 0 2 4 0 0 0 0 0 0 0 0 0
......
root@qemux86-64:~#
----------------------------------------------------------------------
After IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqdss
Ip: 1 64 7 0 2 3 0 0 2 5 0 0 0 0 0 0 0 1 0
......
root@qemux86-64:~#
----------------------------------------------------------------------
ForwDatagrams is updated from 2 to 3.
Reviewed-by: Filip Pudak <filip.pudak@windriver.com>
Signed-off-by: Heng Guo <heng.guo@windriver.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20231011015137.27262-1-heng.guo@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit edf391ff17 ("snmp: add missing counters for RFC 4293") had
already added OutOctets for RFC 4293. In commit 2d8dbb04c6 ("snmp: fix
OutOctets counter to include forwarded datagrams"), OutOctets was
counted again, but not removed from ip_output().
According to RFC 4293 "3.2.3. IP Statistics Tables",
ipipIfStatsOutTransmits is not equal to ipIfStatsOutForwDatagrams. So
"IPSTATS_MIB_OUTOCTETS must be incremented when incrementing" is not
accurate. And IPSTATS_MIB_OUTOCTETS should be counted after fragment.
This patch reverts commit 2d8dbb04c6 ("snmp: fix OutOctets counter to
include forwarded datagrams") and move IPSTATS_MIB_OUTOCTETS to
ip_finish_output2 for ipv4.
Reviewed-by: Filip Pudak <filip.pudak@windriver.com>
Signed-off-by: Heng Guo <heng.guo@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_fwd_update_priority, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 432e05d328 ("net: ipv4: Control SKB reprioritization after forwarding")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() which is used in ip6_forward() and ip_forward()
with kfree_skb_reason().
The new drop reason 'SKB_DROP_REASON_PKT_TOO_BIG' is introduced for
the case that the length of the packet exceeds MTU and can't
fragment.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Jiang Biao <benbjiang@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, skb->tstamp is reset to 0 whenever the skb is forwarded.
If skb->tstamp has the mono delivery_time, clearing it can hurt
the performance when it finally transmits out to fq@phy-dev.
The earlier patch added a skb->mono_delivery_time bit to
flag the skb->tstamp carrying the mono delivery_time.
This patch adds skb_clear_tstamp() helper which keeps
the mono delivery_time and clears everything else.
The delivery_time clearing will be postponed until the stack knows the
skb will be delivered locally. It will be done in a latter patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian noted that rt_uses_gateway has a more subtle use than 'is gateway
set':
https://lore.kernel.org/netdev/alpine.LFD.2.21.1909151104060.2546@ja.home.ssi.bg/
Revert that part of the commit referenced in the Fixes tag.
Currently, there are no u8 holes in 'struct rtable'. There is a 4-byte hole
in the second cacheline which contains the gateway declaration. So move
rt_gw_family down to the gateway declarations since they are always used
together, and then re-use that u8 for rt_uses_gateway. End result is that
rtable size is unchanged.
Fixes: 1550c17193 ("ipv4: Prepare rtable for IPv6 gateway")
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
To allow the gateway to be either an IPv4 or IPv6 address, remove
rt_uses_gateway from rtable and replace with rt_gw_family. If
rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway
to rt_gw4 to represent the IPv4 version.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergey reported that forwarding was no longer working
if fq packet scheduler was used.
This is caused by the recent switch to EDT model, since incoming
packets might have been timestamped by __net_timestamp()
__net_timestamp() uses ktime_get_real(), while fq expects packets
using CLOCK_MONOTONIC base.
The fix is to clear skb->tstamp in forwarding paths.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets marked with 'offload_l3_fwd_mark' were already forwarded by a
capable device and should not be forwarded again by the kernel.
Therefore, have the kernel consume them.
The check is performed in ip{,6}_forward_finish() in order to allow the
kernel to process such packets in ip{,6}_forward() and generate required
exceptions. For example, ICMP redirects.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After IPv4 packets are forwarded, the priority of the corresponding SKB
is updated according to the TOS field of IPv4 header. This overrides any
prioritization done earlier by e.g. an skbedit action or ingress-qos-map
defined at a vlan device.
Such overriding may not always be desirable. Even if the packet ends up
being routed, which implies this is an L3 network node, an administrator
may wish to preserve whatever prioritization was done earlier on in the
pipeline.
Therefore introduce a sysctl that controls this behavior. Keep the
default value at 1 to maintain backward-compatible behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you take a GSO skb, and split it into packets, will the network
length (L3 headers + L4 headers + payload) of those packets be small
enough to fit within a given MTU?
skb_gso_validate_mtu gives you the answer to that question. However,
we recently added to add a way to validate the MAC length of a split GSO
skb (L2+L3+L4+payload), and the names get confusing, so rename
skb_gso_validate_mtu to skb_gso_validate_network_len
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b6 ("net: ip: push gso skb forwarding handling down the stack")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag indicates whether fragmentation of segments is allowed.
Formerly this policy was hardcoded according to IPSKB_FORWARDED (set by
either ip_forward or ipmr_forward).
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_network_seglen is not enough for checking fragment sizes if
skb is using GSO_BY_FRAGS as we have to check frag per frag.
This patch introduces skb_gso_validate_mtu, based on the former, which
will wrap the use case inside it as all calls to skb_gso_network_seglen
were to validate if it fits on a given TMU, and improve the check.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP_INC_STATS_BH() to __IP_INC_STATS(), to
better express this is used in non preemptible context.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 52bd2d62ce ("net: better skb->sender_cpu and skb->napi_id cohabitation")
skb_sender_cpu_clear() becomes empty and can be removed.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dst_output_okfn with dst_output
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is immediately motivated by the bridge code that chains functions that
call into netfilter. Without passing net into the okfns the bridge code would
need to guess about the best expression for the network namespace to process
packets in.
As net is frequently one of the first things computed in continuation functions
after netfilter has done it's job passing in the desired network namespace is in
many cases a code simplification.
To support this change the function dst_output_okfn is introduced to
simplify passing dst_output as an okfn. For the moment dst_output_okfn
just silently drops the struct net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a network namespace parameter into the netfilter hooks. At the
call site of the netfilter hooks the path a packet is taking through
the network stack is well known which allows the network namespace to
be easily and reliabily.
This allows the replacement of magic code like
"dev_net(state->in?:state->out)" that appears at the start of most
netfilter hooks with "state->net".
In almost all cases the network namespace passed in is derived
from the first network device passed in, guaranteeing those
paths will not see any changes in practice.
The exceptions are:
xfrm/xfrm_output.c:xfrm_output_resume() xs_net(skb_dst(skb)->xfrm)
ipvs/ip_vs_xmit.c:ip_vs_nat_send_or_cont() ip_vs_conn_net(cp)
ipvs/ip_vs_xmit.c:ip_vs_send_or_cont() ip_vs_conn_net(cp)
ipv4/raw.c:raw_send_hdrinc() sock_net(sk)
ipv6/ip6_output.c:ip6_xmit() sock_net(sk)
ipv6/ndisc.c:ndisc_send_skb() dev_net(skb->dev) not dev_net(dst->dev)
ipv6/raw.c:raw6_send_hdrinc() sock_net(sk)
br_netfilter_hooks.c:br_nf_pre_routing_finish() dev_net(skb->dev) before skb->dev is set to nf_bridge->physindev
In all cases these exceptions seem to be a better expression for the
network namespace the packet is being processed in then the historic
"dev_net(in?in:out)". I am documenting them in case something odd
pops up and someone starts trying to track down what happened.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compute struct net from the input device in ip_forward before it is
used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sock paramter to dst_output making dst_output_sk superfluous.
Add a skb->sk parameter to all of the callers of dst_output
Have the callers of dst_output_sk call dst_output.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send icmp pmtu error if we find that the largest fragment of df-skb
exceeded the output path mtu.
The ip output path will still catch this later on but we can avoid the
forward/postrouting hook traversal by rejecting right away.
This is what ipv6 already does.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets
Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.
This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.
v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
John reported that my previous commit added a regression
on his router.
This is because sender_cpu & napi_id share a common location,
so get_xps_queue() can see garbage and perform an out of bound access.
We need to make sure sender_cpu is cleared before doing the transmit,
otherwise any NIC busy poll enabled (skb_mark_napi_id()) can trigger
this bug.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: John <jw@nuclearfallout.net>
Bisected-by: John <jw@nuclearfallout.net>
Fixes: 2bd82484bb ("xps: fix xps for stacked devices")
Signed-off-by: David S. Miller <davem@davemloft.net>
Not caching dst_entries which cause redirects could be exploited by hosts
on the same subnet, causing a severe DoS attack. This effect aggravated
since commit f886497212 ("ipv4: fix dst race in sk_dst_get()").
Lookups causing redirects will be allocated with DST_NOCACHE set which
will force dst_release to free them via RCU. Unfortunately waiting for
RCU grace period just takes too long, we can end up with >1M dst_entries
waiting to be released and the system will run OOM. rcuos threads cannot
catch up under high softirq load.
Attaching the flag to emit a redirect later on to the specific skb allows
us to cache those dst_entries thus reducing the pressure on allocation
and deallocation.
This issue was discovered by Marcelo Leitner.
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by several people, rename local_df to ignore_df,
since it means "ignore df bit if it is set".
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing the segmentation in the forward path has one major drawback:
When using virtio, we may process gso udp packets coming
from host network stack. In that case, netfilter POSTROUTING
will see one packet with udp header followed by multiple ip
fragments.
Delay the segmentation and do it after POSTROUTING invocation
to avoid this.
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
local_df means 'ignore DF bit if set', so if its set we're
allowed to perform ip fragmentation.
This wasn't noticed earlier because the output path also drops such skbs
(and emits needed icmp error) and because netfilter ip defrag did not
set local_df until couple of days ago.
Only difference is that DF-packets-larger-than MTU now discarded
earlier (f.e. we avoid pointless netfilter postrouting trip).
While at it, drop the repeated test ip_exceeds_mtu, checking it once
is enough...
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets which have L2 address different from ours should be
already filtered before entering into ip_forward().
Perform that check at the beginning to avoid processing such packets.
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner reported problems when the forwarding link path
has a lower mtu than the incoming one if the inbound interface supports GRO.
Given:
Host <mtu1500> R1 <mtu1200> R2
Host sends tcp stream which is routed via R1 and R2. R1 performs GRO.
In this case, the kernel will fail to send ICMP fragmentation needed
messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu
checks in forward path. Instead, Linux tries to send out packets exceeding
the mtu.
When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does
not fragment the packets when forwarding, and again tries to send out
packets exceeding R1-R2 link mtu.
This alters the forwarding dstmtu checks to take the individual gso
segment lengths into account.
For ipv6, we send out pkt too big error for gso if the individual
segments are too big.
For ipv4, we either send icmp fragmentation needed, or, if the DF bit
is not set, perform software segmentation and let the output path
create fragments when the packet is leaving the machine.
It is not 100% correct as the error message will contain the headers of
the GRO skb instead of the original/segmented one, but it seems to
work fine in my (limited) tests.
Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid
sofware segmentation.
However it turns out that skb_segment() assumes skb nr_frags is related
to mss size so we would BUG there. I don't want to mess with it considering
Herbert and Eric disagree on what the correct behavior should be.
Hannes Frederic Sowa notes that when we would shrink gso_size
skb_segment would then also need to deal with the case where
SKB_MAX_FRAGS would be exceeded.
This uses sofware segmentation in the forward path when we hit ipv4
non-DF packets and the outgoing link mtu is too small. Its not perfect,
but given the lack of bug reports wrt. GRO fwd being broken this is a
rare case anyway. Also its not like this could not be improved later
once the dust settles.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
While forwarding we should not use the protocol path mtu to calculate
the mtu for a forwarded packet but instead use the interface mtu.
We mark forwarded skbs in ip_forward with IPSKB_FORWARDED, which was
introduced for multicast forwarding. But as it does not conflict with
our usage in unicast code path it is perfect for reuse.
I moved the functions ip_sk_accept_pmtu, ip_sk_use_pmtu and ip_skb_dst_mtu
along with the new ip_dst_mtu_maybe_forward to net/ip.h to fix circular
dependencies because of IPSKB_FORWARDED.
Because someone might have written a software which does probe
destinations manually and expects the kernel to honour those path mtus
I introduced a new per-namespace "ip_forward_use_pmtu" knob so someone
can disable this new behaviour. We also still use mtus which are locked on a
route for forwarding.
The reason for this change is, that path mtus information can be injected
into the kernel via e.g. icmp_err protocol handler without verification
of local sockets. As such, this could cause the IPv4 forwarding path to
wrongfully emit fragmentation needed notifications or start to fragment
packets along a path.
Tunnel and ipsec output paths clear IPCB again, thus IPSKB_FORWARDED
won't be set and further fragmentation logic will use the path mtu to
determine the fragmentation size. They also recheck packet size with
help of path mtu discovery and report appropriate errors.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new flag to remember when route is via gateway.
We will use it to allow rt_gateway to contain address of
directly connected host for the cases when DST_NOCACHE is
used or when the NH exception caches per-destination route
without DST_NOCACHE flag, i.e. when routes are not used for
other destinations. By this way we force the neighbour
resolving to work with the routed destination but we
can use different address in the packet, feature needed
for IPVS-DR where original packet for virtual IP is routed
via route to real IP.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the change "Adjust semantics of rt->rt_gateway"
(commit f8126f1d51) rt_gateway can be 0 but ip_forward() compares
it directly with nexthop. What we want here is to check if traffic
is to directly connected nexthop and to fail if using gateway.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4293 defines ipIfStatsOutOctets (similar definition for
ipSystemStatsOutOctets):
The total number of octets in IP datagrams delivered to the lower
layers for transmission. Octets from datagrams counted in
ipIfStatsOutTransmits MUST be counted here.
And ipIfStatsOutTransmits:
The total number of IP datagrams that this entity supplied to the
lower layers for transmission. This includes datagrams generated
locally and those forwarded by this entity.
Therefore, IPSTATS_MIB_OUTOCTETS must be incremented when incrementing
IPSTATS_MIB_OUTFORWDATAGRAMS.
IP_UPD_PO_STATS is not used since ipIfStatsOutRequests must not
include forwarded datagrams:
The total number of IP datagrams that local IP user-protocols
(including ICMP) supplied to IP in requests for transmission. Note
that this counter does not include any datagrams counted in
ipIfStatsOutForwDatagrams.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch errors of the following type:
* ERROR: "foo * bar" should be "foo *bar"
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can not update iph->daddr in ip_options_rcv_srr(), It is too early.
When some exception ocurred later (eg. in ip_forward() when goto
sr_failed) we need the ip header be identical to the original one as
ICMP need it.
Add a field 'nexthop' in struct ip_options to save nexthop of LSRR
or SSRR option.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I swear none of my compilers warned about this, yet it is so
obvious.
> net/ipv4/ip_forward.c: In function 'ip_forward':
> net/ipv4/ip_forward.c:87: warning: 'iph' may be used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
No matter what kind of header mangling occurs due to IP options
processing, rt->rt_dst will always equal iph->daddr in the packet.
So we can safely use iph->daddr instead of rt->rt_dst here.
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
