Arseniy Krasnov says:
====================
vsock: update tools and error handling
Patchset consists of two parts:
1) Kernel patch
One patch from Bobby Eshleman. I took single patch from Bobby:
https://lore.kernel.org/lkml/d81818b868216c774613dd03641fcfe63cc55a45
.1660362668.git.bobby.eshleman@bytedance.com/ and use only part for
af_vsock.c, as VMCI and Hyper-V parts were rejected.
I used it, because for SOCK_SEQPACKET big messages handling was broken -
ENOMEM was returned instead of EMSGSIZE. And anyway, current logic which
always replaces any error code returned by transport to ENOMEM looks
strange for me also(for example in EMSGSIZE case it was changed to
ENOMEM).
2) Tool patches
Since there is work on several significant updates for vsock(virtio/
vsock especially): skbuff, DGRAM, zerocopy rx/tx, so I think that this
patchset will be useful.
This patchset updates vsock tests and tools a little bit. First of all
it updates test suite: two new tests are added. One test is reworked
message bound test. Now it is more complex. Instead of sending 1 byte
messages with one MSG_EOR bit, it sends messages of random length(one
half of messages are smaller than page size, second half are bigger)
with random number of MSG_EOR bits set. Receiver also don't know total
number of messages. Message bounds control is maintained by hash sum
of messages length calculation. Second test is for SOCK_SEQPACKET - it
tries to send message with length more than allowed. I think both tests
will be useful for DGRAM support also.
Third thing that this patchset adds is small utility to test vsock
performance for both rx and tx. I think this util could be useful as
'iperf'/'uperf', because:
1) It is small comparing to 'iperf' or 'uperf', so it very easy to add
new mode or feature to it(especially vsock specific).
2) It allows to set SO_RCVLOWAT and SO_VM_SOCKETS_BUFFER_SIZE option.
Whole throughtput depends on both parameters.
3) It is located in the kernel source tree, so it could be updated by
the same patchset which changes related kernel functionality in vsock.
I used this util very often to check performance of my rx zerocopy
support(this tool has rx zerocopy support, but not in this patchset).
Here is comparison of outputs from three utils: 'iperf', 'uperf' and
'vsock_perf'. In all three cases sender was at guest side. rx and
tx buffers were always 64Kb(because by default 'uperf' uses 8K).
iperf:
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.00 sec 12.8 GBytes 11.0 Gbits/sec sender
[ 5] 0.00-10.00 sec 12.8 GBytes 11.0 Gbits/sec receiver
uperf:
Total 16.27GB / 11.36(s) = 12.30Gb/s 23455op/s
vsock_perf:
tx performance: 12.301529 Gbits/s
rx performance: 12.288011 Gbits/s
Results are almost same in all three cases.
Patchset was rebased and tested on skbuff v9 patch from Bobby Eshleman:
https://lore.kernel.org/netdev/20230107002937.899605-1-bobby.eshleman@bytedance.com/
====================
Link: https://lore.kernel.org/r/67cd2d0a-1c58-baac-7b39-b8d4ea44f719@sberdevices.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds test for sending message, bigger than peer's buffer size.
For SOCK_SEQPACKET socket it must fail, as this type of socket has
message size limit.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This updates message bound test making it more complex. Instead of
sending 1 bytes messages with one MSG_EOR bit, it sends messages of
random length(one half of messages are smaller than page size, second
half are bigger) with random number of MSG_EOR bits set. Receiver
also don't know total number of messages.
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This removes behaviour, where error code returned from any transport
was always switched to ENOMEM. For example when user tries to send too
big message via SEQPACKET socket, transport layers return EMSGSIZE, but
this error code was always replaced with ENOMEM and returned to user.
Signed-off-by: Bobby Eshleman <bobby.eshleman@bytedance.com>
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
10 small fixes (less the one that cleaned up a reverted removal), 9 in
drivers of which the ufs one is the most critical. The single core
patch is a minor speedup to error handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCY77DTiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbE4AQDhMCqJ
k59nF9+6ll0kbY7pNPG6TtaX9bK6HZ9caZ5kNAEApw/aZahHnl3kKS3xL3XeK8Yy
N8m/eda0hlFy5aL0XNg=
=VJVR
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Ten small fixes (less the one that cleaned up a reverted removal),
nine in drivers of which the ufs one is the most critical.
The single core patch is a minor speedup to error handling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: Grab the ATA port lock in sas_ata_device_link_abort()
scsi: hisi_sas: Fix tag freeing for reserved tags
scsi: ufs: core: WLUN suspend SSU/enter hibern8 fail recovery
scsi: scsi_debug: Delete unreachable code in inquiry_vpd_b0()
scsi: mpi3mr: Refer CONFIG_SCSI_MPI3MR in Makefile
scsi: core: scsi_error: Do not queue pointless abort workqueue functions
scsi: storvsc: Fix swiotlb bounce buffer leak in confidential VM
scsi: iscsi: Fix multiple iSCSI session unbind events sent to userspace
scsi: mpi3mr: Remove usage of dma_get_required_mask() API
scsi: mpt3sas: Remove usage of dma_get_required_mask() API
Queue spinlock is currently held in mtk_wed_wo_queue_rx_clean and
mtk_wed_wo_queue_refill routines for MTK Wireless Ethernet Dispatcher
MCU rx queue. mtk_wed_wo_queue_refill() is running during initialization
and in rx tasklet while mtk_wed_wo_queue_rx_clean() is running in
mtk_wed_wo_hw_deinit() during hw de-init phase after rx tasklet has been
disabled. Since mtk_wed_wo_queue_rx_clean and mtk_wed_wo_queue_refill
routines can't run concurrently get rid of spinlock for mcu rx queue.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/36ec3b729542ea60898471d890796f745479ba32.1673342990.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add timeout polling wait for auxiliary timestamps snapshot FIFO clear bit
(ATSFC) to clear. This is to ensure no residue fifo value is being read
erroneously.
Fixes: f4da56529d ("net: stmmac: Add support for external trigger timestamping")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Link: https://lore.kernel.org/r/20230111050200.2130-1-noor.azura.ahmad.tarmizi@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-01-10 (ixgbe, igc, iavf)
This series contains updates to ixgbe, igc, and iavf drivers.
Yang Yingliang adds calls to pci_dev_put() for proper ref count tracking
on ixgbe.
Christopher adds setting of Toggle on Target Time bits for proper
pulse per second (PPS) synchronization for igc.
Daniil Tatianin fixes, likely, copy/paste issue that misreported
destination instead of source for IP mask for iavf error.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf/iavf_main: actually log ->src mask when talking about it
igc: Fix PPS delta between two synchronized end-points
ixgbe: fix pci device refcount leak
====================
Link: https://lore.kernel.org/r/20230110223825.648544-1-anthony.l.nguyen@intel.com
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reference needs to keep the instance memory around, but also
the instance lock must remain valid. Users will take the lock,
check registration status and release the lock. mutex_destroy()
etc. belong in the same place as the freeing of the memory.
Unfortunately lockdep_unregister_key() sleeps so we need
to switch the an rcu_work.
Note that the problem is a bit hard to repro, because
devlink_pernet_pre_exit() iterates over registered instances.
AFAIU the instances must get devlink_free()d concurrently with
the namespace getting deleted for the problem to occur.
Reported-by: syzbot+d94d214ea473e218fc89@syzkaller.appspotmail.com
Reported-by: syzbot+9f0dd863b87113935acf@syzkaller.appspotmail.com
Fixes: 9053637e0d ("devlink: remove the registration guarantee of references")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230111042908.988199-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before the commit under Fixes the page would have been released
from the pool before the napi_alloc_skb() call, so normal page
freeing was fine (released page == no longer in the pool).
After the change we just mark the page for recycling so it's still
in the pool if the skb alloc fails, we need to recycle.
Same commit added the same bug in the new bnxt_rx_multi_page_skb().
Fixes: 1dc4c557bf ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Link: https://lore.kernel.org/r/20230111042547.987749-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, it used old rss size to get current tc mode. As a result, the
rss size is updated, but the tc mode is still configured based on the old
rss size.
So this patch fixes it by using the new rss size in both process.
Fixes: 93969dc14f ("net: hns3: refactor VF rss init APIs with new common rss init APIs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230110115359.10163-1-lanhao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are still single reports of systems where ASPM incompatibilities
cause tx timeouts. It's not clear whom to blame, so let's disable
ASPM in case of a tx timeout.
v2:
- add one-time warning for informing the user
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/92369a92-dc32-4529-0509-11459ba0e391@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Make 'perf kmem' cope with the removal of some kmem:kmem_cache_alloc_node and
kmem:kmalloc_node in the 11e9734bcb ("mm/slab_common: unify NUMA and
UMA version of tracepoints") commit, making sure it works with Linux >= 6.2 as well
as with older kernels where those tracepoints are present.
- Also make it handle the new "node" kmem:kmalloc and kmem:kmem_cache_alloc tracepoint
field introduced in that same commit.
- Fix hardware tracing PMU address filter duplicate symbol selection, that was
preventing to match with static functions with the same name present in different
object files.
- Fix regression on what linux/types.h file gets used to build the "BPF prologue"
'perf test' entry, the system one lacks the fmode_t definition used in this test,
so provide that type in the test itself.
- Avoid build breakage with libbpf < 0.8.0 + LIBBPF_DYNAMIC=1. If the user asks for
linking with the libbpf package provided by the distro, then it has to be >= 0.8.0.
Using the libbpf supplied with the kernel would be a fallback in that case.
- Fix the build when libbpf isn't available or explicitly disabled via NO_LIBBPF=1.
- Don't try to install libtraceevent plugins as its not anymore in the kernel sources
and will thus always fail.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCY77xBAAKCRCyPKLppCJ+
J9B5AQCjCu18vsulBd0nRcfBZDGdw2P53OJl10slaAdU4t6RLgD/fwhRZ5PlmDiY
TD+rARyZYsOsZ+9bVpJTZKh3nuCnewo=
=T8iN
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v6.2-2-2023-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Make 'perf kmem' cope with the removal of some
kmem:kmem_cache_alloc_node and kmem:kmalloc_node in the
11e9734bcb ("mm/slab_common: unify NUMA and UMA version of
tracepoints") commit, making sure it works with Linux >= 6.2 as well
as with older kernels where those tracepoints are present.
- Also make it handle the new "node" kmem:kmalloc and
kmem:kmem_cache_alloc tracepoint field introduced in that same
commit.
- Fix hardware tracing PMU address filter duplicate symbol selection,
that was preventing to match with static functions with the same name
present in different object files.
- Fix regression on what linux/types.h file gets used to build the "BPF
prologue" 'perf test' entry, the system one lacks the fmode_t
definition used in this test, so provide that type in the test
itself.
- Avoid build breakage with libbpf < 0.8.0 + LIBBPF_DYNAMIC=1. If the
user asks for linking with the libbpf package provided by the distro,
then it has to be >= 0.8.0. Using the libbpf supplied with the kernel
would be a fallback in that case.
- Fix the build when libbpf isn't available or explicitly disabled via
NO_LIBBPF=1.
- Don't try to install libtraceevent plugins as its not anymore in the
kernel sources and will thus always fail.
* tag 'perf-tools-fixes-for-v6.2-2-2023-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf auxtrace: Fix address filter duplicate symbol selection
perf bpf: Avoid build breakage with libbpf < 0.8.0 + LIBBPF_DYNAMIC=1
perf build: Fix build error when NO_LIBBPF=1
perf tools: Don't install libtraceevent plugins as its not anymore in the kernel sources
perf kmem: Support field "node" in evsel__process_alloc_event() coping with recent tracepoint restructuring
perf kmem: Support legacy tracepoints
perf build: Properly guard libbpf includes
perf tests bpf prologue: Fix bpf-script-test-prologue test compile issue with clang
Convert MDIO bus multiplexer/glue of Amlogic G12a SoC family bindings
to dt-schema.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a match has been made to the nth duplicate symbol, return
success not error.
Example:
Before:
$ cat file.c
cat: file.c: No such file or directory
$ cat file1.c
#include <stdio.h>
static void func(void)
{
printf("First func\n");
}
void other(void);
int main()
{
func();
other();
return 0;
}
$ cat file2.c
#include <stdio.h>
static void func(void)
{
printf("Second func\n");
}
void other(void)
{
func();
}
$ gcc -Wall -Wextra -o test file1.c file2.c
$ perf record -e intel_pt//u --filter 'filter func @ ./test' -- ./test
Multiple symbols with name 'func'
#1 0x1149 l func
which is near main
#2 0x1179 l func
which is near other
Disambiguate symbol name by inserting #n after the name e.g. func #2
Or select a global symbol by inserting #0 or #g or #G
Failed to parse address filter: 'filter func @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
$ perf record -e intel_pt//u --filter 'filter func #2 @ ./test' -- ./test
Failed to parse address filter: 'filter func #2 @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
After:
$ perf record -e intel_pt//u --filter 'filter func #2 @ ./test' -- ./test
First func
Second func
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.016 MB perf.data ]
$ perf script --itrace=b -Ftime,flags,ip,sym,addr --ns
1231062.526977619: tr strt 0 [unknown] => 558495708179 func
1231062.526977619: tr end call 558495708188 func => 558495708050 _init
1231062.526979286: tr strt 0 [unknown] => 55849570818d func
1231062.526979286: tr end return 55849570818f func => 55849570819d other
Fixes: 1b36c03e35 ("perf record: Add support for using symbols in address filters")
Reported-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Dolgov <9erthalion6@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230110185659.15979-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Use READ_ONCE() before cmpxchg() to prevent that the compiler generates
code that fetches the to be compared old value several times from memory.
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20230109145456.2895385-1-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Make sure that *ptr__ within arch_this_cpu_to_op_simple() is only
dereferenced once by using READ_ONCE(). Otherwise the compiler could
generate incorrect code.
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The current cmpxchg_double() loops within the perf hw sampling code do not
have READ_ONCE() semantics to read the old value from memory. This allows
the compiler to generate code which reads the "old" value several times
from memory, which again allows for inconsistencies.
For example:
/* Reset trailer (using compare-double-and-swap) */
do {
te_flags = te->flags & ~SDB_TE_BUFFER_FULL_MASK;
te_flags |= SDB_TE_ALERT_REQ_MASK;
} while (!cmpxchg_double(&te->flags, &te->overflow,
te->flags, te->overflow,
te_flags, 0ULL));
The compiler could generate code where te->flags used within the
cmpxchg_double() call may be refetched from memory and which is not
necessarily identical to the previous read version which was used to
generate te_flags. Which in turn means that an incorrect update could
happen.
Fix this by adding READ_ONCE() semantics to all cmpxchg_double()
loops. Given that READ_ONCE() cannot generate code on s390 which atomically
reads 16 bytes, use a private compare-and-swap-double implementation to
achieve that.
Also replace cmpxchg_double() with the private implementation to be able to
re-use the old value within the loops.
As a side effect this converts the whole code to only use bit fields
to read and modify bits within the hws trailer header.
Reported-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/linux-s390/Y71QJBhNTIatvxUT@osiris/T/#ma14e2a5f7aa8ed4b94b6f9576799b3ad9c60f333
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The newly added spi-cs-setup-ns doesn't really fit with the existing
property names for delays, rename it so that it does before it makes it
into a release and becomes ABI.
The two debug messages in spidev_open() dereference spidev->spi without
taking the lock and without checking if it's not null. This can lead to
a crash. Drop the messages as they're not needed - the user-space will
get informed about ENOMEM with the syscall return value.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a spinlock in place that is taken in file_operations callbacks
whenever we check if spidev->spi is still alive (not null). It's also
taken when spidev->spi is set to NULL in remove().
This however doesn't protect the code against driver unbind event while
one of the syscalls is still in progress. To that end we need a lock taken
continuously as long as we may still access spidev->spi. As both the file
ops and the remove callback are never called from interrupt context, we
can replace the spinlock with a mutex.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The total cork length created by ip6_append_data includes extension
headers, so we must exclude them when comparing them against the
IPV6_CHECKSUM offset which does not include extension headers.
Reported-by: Kyle Zeng <zengyhkyle@gmail.com>
Fixes: 357b40a18b ("[IPV6]: IPV6_CHECKSUM socket option can corrupt kernel memory")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) From Gal: Add debugfs entries for netdev nic driver
- ktls, flow steering and hairpin info
- useful for debug and performance analysis
- e.g hairpin queue attributes, dump ktls tx pool size, etc
2) From Maher: Update shared buffer configuration on PFC commands
2.1) For every change of buffer's headroom, recalculate the size of shared
buffer to be equal to "total_buffer_size" - "new_headroom_size".
The new shared buffer size will be split in ratio of 3:1 between
lossy and lossless pools, respectively.
2.2) For each port buffer change, count the number of lossless buffers.
If there is only one lossless buffer, then set its lossless pool
usage threshold to be infinite. Otherwise, if there is more than
one lossless buffer, set a usage threshold for each lossless buffer.
While at it, add more verbosity to debug prints when handling user
commands, to assist in future debug.
3) From Tariq: Throttle high rate FW commands
4) From Shay: Properly initialize management PF
5) Various cleanup patches
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmO+SBsACgkQSD+KveBX
+j71fwf+Ne9PWyF4F3fxdYSr6LhqnP6S8TlgFDJAtpmKPjvo09mAhqI/h+iG4b/P
EByIY2h1kHyyUL3jZW4YDbSUcsYpg71cwVSN+DkIKaxXDK3RDeVjt7ndmus76GP5
an+snDevmRRqwFktNUPA8akEmq5h8qRzT315IyTiJKGIJkrJCoJ54/w9AsyhDiNL
pwuJk7OxR0yVW5zESub1QPBgEBT/61raRrAh6vSCYya0zHsbRgNsR6KcRA5HU7FF
+uvj4qjzaX0BMfZm74gDsmOuKnB0Dg4U64tfGRV55wG8vXay7Ar2zLFVdqFWYaJL
vSBmn5doU+Lh0A5MqZSi+l6VHJ/rFA==
=N2He
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2023-01-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2023-01-10
1) From Gal: Add debugfs entries for netdev nic driver
- ktls, flow steering and hairpin info
- useful for debug and performance analysis
- e.g hairpin queue attributes, dump ktls tx pool size, etc
2) From Maher: Update shared buffer configuration on PFC commands
2.1) For every change of buffer's headroom, recalculate the size of shared
buffer to be equal to "total_buffer_size" - "new_headroom_size".
The new shared buffer size will be split in ratio of 3:1 between
lossy and lossless pools, respectively.
2.2) For each port buffer change, count the number of lossless buffers.
If there is only one lossless buffer, then set its lossless pool
usage threshold to be infinite. Otherwise, if there is more than
one lossless buffer, set a usage threshold for each lossless buffer.
While at it, add more verbosity to debug prints when handling user
commands, to assist in future debug.
3) From Tariq: Throttle high rate FW commands
4) From Shay: Properly initialize management PF
5) Various cleanup patches
Piergiorgio Beruto says:
====================
net: add PLCA RS support and onsemi NCN26000
This patchset adds support for getting/setting the Physical Layer
Collision Avoidace (PLCA) Reconciliation Sublayer (RS) configuration and
status on Ethernet PHYs that supports it.
PLCA is a feature that provides improved media-access performance in terms
of throughput, latency and fairness for multi-drop (P2MP) half-duplex PHYs.
PLCA is defined in Clause 148 of the IEEE802.3 specifications as amended
by 802.3cg-2019. Currently, PLCA is supported by the 10BASE-T1S single-pair
Ethernet PHY defined in the same standard and related amendments. The OPEN
Alliance SIG TC14 defines additional specifications for the 10BASE-T1S PHY,
including a standard register map for PHYs that embeds the PLCA RS (see
PLCA management registers at https://www.opensig.org/about/specifications/).
The changes proposed herein add the appropriate ethtool netlink interface
for configuring the PLCA RS on PHYs that supports it. A separate patchset
further modifies the ethtool userspace program to show and modify the
configuration/status of the PLCA RS.
Additionally, this patchset adds support for the onsemi NCN26000
Industrial Ethernet 10BASE-T1S PHY that uses the newly added PLCA
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the onsemi NCN26000 10BASE-T1S industrial
Ethernet PHY. The driver supports Point-to-Multipoint operation without
auto-negotiation and with link control handling. The PHY also features
PLCA for improving performance in P2MP mode.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support in phylib to read/write PLCA configuration for
Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA
Management Registers" specifications. These can be found at
https://www.opensig.org/about/specifications/
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the PLCA Reconciliation Sublayer on
multi-drop PHYs that support IEEE802.3cg-2019 Clause 148 (e.g.,
10BASE-T1S). This patch adds the appropriate netlink interface
to ethtool.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ptp was not enabled due to missing IRQ for instance,
lan966x_ptp_deinit() will dereference NULL pointers.
Fixes: d096459494 ("net: lan966x: Add support for ptp clocks")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'accel_tcp' is allocted by kvzalloc() now, which is a small chunk.
Use kzalloc() directly instead of kvzalloc().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Return value from mlx5dr_send_postsend_action() directly instead of taking
this in another redundant variable.
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Zero-length arrays are deprecated[1]. Replace struct mlx5e_rx_wqe_cyc's
"data" 0-length array with a flexible array. Detected with GCC 13,
using -fstrict-flex-arrays=3:
drivers/net/ethernet/mellanox/mlx5/core/en_main.c: In function 'mlx5e_alloc_rq':
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:827:42: warning: array subscript f is outside array bounds of 'struct mlx5_wqe_data_seg[0]' [-Warray-bounds=]
827 | wqe->data[f].byte_count = 0;
| ~~~~~~~~~^~~
In file included from drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.h:11,
from drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:48,
from drivers/net/ethernet/mellanox/mlx5/core/en_main.c:42:
drivers/net/ethernet/mellanox/mlx5/core/en.h:250:39: note: while referencing 'data'
250 | struct mlx5_wqe_data_seg data[0];
| ^~~~
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Certain connection-based device-offload protocols (like TLS) use
per-connection HW objects to track the state, maintain the context, and
perform the offload properly. Some of these objects are created,
modified, and destroyed via FW commands. Under high connection rate,
this type of FW commands might continuously populate all slots of the FW
command interface and throttle it, while starving other critical control
FW commands.
Limit these throttle commands to using only up to a portion (half) of
the FW command interface slots. FW commands maximal rate is not hit, and
the same high rate is still reached when applying this limitation.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Introduce an opcode getter in the FW command interface, and use it.
Initialize the entry's opcode field early in cmd_alloc_ent() and use it
when possible.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Enable initialization of DPU Management PF, which is a new loopback PF
designed for communication with BMC.
For now Management PF doesn't support nor require most upper layer
protocols so avoid them.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
We refer to a TC NIC rule that involves forwarding as "hairpin".
Hairpin queues are mlx5 hardware specific implementation for hardware
forwarding of such packets.
For debug purposes, introduce debugfs files which:
* Expose the number of active hairpins
* Dump the hairpin table
* Allow control over the number and size of the hairpin queues instead
of the hard-coded values.
This allows us to get visibility of the feature in order to improve it
for next generation hardware.
Add debugfs files:
fs/tc/hairpin_num_active
fs/tc/hairpin_num_queues
fs/tc/hairpin_queue_size
fs/tc/hairpin_table_dump
Note that the new values will only take effect on the next queues
creation, it does not affect existing queues.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a debugfs directory for flow steering related information.
The directory is currently empty, and will hold the 'tc' subdirectory in
a downstream patch.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In preparation for downstream work to expose hairpin queues parameters,
introduce a hairpin parameters struct as part of the tc structure.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add TLS debugfs to improve observability by exposing the size of the tls
TX pool.
To observe the size of the TX pool:
$ cat /sys/kernel/debug/mlx5/<pci>/nic/tls/tx/pool_size
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Co-developed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Similar to the mlx5_core debugfs, lay the groundwork for mlx5e debugfs
files under /sys/kernel/debug/mlx5/<pci>/nic/..
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, the user can modify device's receive buffer size, modify the
mapping between QoS priority groups to buffers and change the buffer
state to become lossy/lossless via pfc command.
However, the shared receive buffer pool alignments, as a result of
such commands, is performed only when the shared buffer is in FW ownership.
When a user changes the mapping of priority groups or buffer size,
the shared buffer is moved to SW ownership.
Therefore, for devices that support shared buffer, handle the shared buffer
alignments in accordance to user's desired configurations.
Meaning, the following will be performed:
1. For every change of buffer's headroom, recalculate the size of shared
buffer to be equal to "total_buffer_size" - "new_headroom_size".
The new shared buffer size will be split in ratio of 3:1 between
lossy and lossless pools, respectively.
2. For each port buffer change, count the number of lossless buffers.
If there is only one lossless buffer, then set its lossless pool
usage threshold to be infinite. Otherwise, if there is more than
one lossless buffer, set a usage threshold for each lossless buffer.
While at it, add more verbosity to debug prints when handling user
commands, to assist in future debug.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
To allow users to configure shared receive buffer parameters through
dcbnl callbacks, expose an API to query and modify SBPR and SBCM registers,
which will be used in the upcoming patch.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-01-09 (ice)
This series contains updates to ice driver only.
Jiasheng Jiang frees allocated cmd_buf if write_buf allocation failed to
prevent memory leak.
Yuan Can adds check, and proper cleanup, of gnss_tty_port allocation call
to avoid memory leaks.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Add check for kzalloc
ice: Fix potential memory leak in ice_gnss_tty_write()
====================
Link: https://lore.kernel.org/r/20230109225358.3478060-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
