ECC layout definitions are currently exposed using the nand_ecclayout
struct which embeds oobfree and eccpos arrays with predefined size.
This approach was acceptable when NAND chips were providing relatively
small OOB regions, but MLC and TLC now provide OOB regions of several
hundreds of bytes, which implies a non negligible overhead for everybody
even those who only need to support legacy NANDs.
Create an mtd_ooblayout_ops interface providing the same functionality
(expose the ECC and oobfree layout) without the need for this huge
structure.
The mtd->ecclayout is now deprecated and should be replaced by the
equivalent mtd_ooblayout_ops. In the meantime we provide a wrapper around
the ->ecclayout field to ease migration to this new model.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the mtd_set_ecclayout() helper instead of directly assigning the
mtd->ecclayout field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use the mtd_set_ecclayout() helper instead of directly assigning the
mtd->ecclayout field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the mtd_set_ecclayout() helper instead of directly assigning the
mtd->ecclayout field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the mtd_set_ecclayout() helper instead of directly assigning the
mtd->ecclayout field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to ecclayout fields, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_ooblayout_xxx() helper functions have been added to avoid direct
accesses to the ecclayout field, and thus ease for future reworks.
Use these helpers in all places where the oobfree[] and eccpos[] arrays
where directly accessed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In order to make the ecclayout definition completely dynamic we need to
rework the way the OOB layout are defined and iterated.
Create a few mtd_ooblayout_xxx() helpers to ease OOB bytes manipulation
and hide ecclayout internals to their users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Allow for NULL cur_offs values when the caller does not know where the
NAND page register pointer points to.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
sunxi_nfc_hw_ecc_read_chunk() always retrieves the ECC and protected free
bytes, no matter if the user really asked for it or not. This can take a
non negligible amount of time, especially on NAND chips exposing large OOB
areas (> 1KB). Make it optional.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In order to support DMA operations in a clean way we need to extract some
of the logic coded in sunxi_nfc_hw_ecc_read/write_page() into their own
function.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND operations are so fast that it doesn't make any sense to use
interrupt based waits (the scheduling overhead is not worth it).
Rename sunxi_nfc_wait_int() into sunxi_nfc_wait_events() and add a
parameter to specify whether polling should be used or not.
Note that all sunxi_nfc_wait_int() are moved to the polling approach now,
but this should change as soon as we have more information about the
approximate time we are about to wait (can be extracted from the NAND
timings, and the type of operation).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
->dev_ready() is not supposed to wait for busy to ready solution (this is
the role of ->waitfunc()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When the NAND controller operates in DMA mode it can pipeline ECC
operations which improves the throughput.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NFC_ECC_ERR_CNT() is not taking into account the case when the NAND chip
contains more than 4 ECC blocks (NANDs with 4kB+ pages).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We don't need to manually toggle the CE line since the controller handles
it for us. Moreover, keeping the CE line low when interacting with a DDR
NAND can be problematic (data loss in some corner cases).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Try to pack address and command cycles into a single NAND controller
command to avoid polling the status register for each single change
on the NAND bus.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Being able to read subpages can greatly improve read performances if the
MTD user is only interested in a small section of a NAND page.
This is particularly true with large pages (>= 8k).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Allwinner's ECC engine is capable of protecting a few bytes of the OOB
area. Implement specific OOB functions to benefit from this capability.
Also, when in raw mode, the randomizer is disabled, which means you'll
only be able to retrieve randomized data, which is not really useful
for most applications.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Export the default read/write oob functions (for the standard and syndrome
scheme), so that drivers can use them for their raw implementation and
implement their own functions for the normal oob operation.
This is required if your ECC engine is capable of fixing some of the OOB
data. In this case you have to overload the ->read_oob() and ->write_oob(),
but if you don't specify the ->read/write_oob_raw() functions they are
assigned to the ->read/write_oob() implementation, which is not what you
want.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Adapt the NAND controller clk rate to the tWB, tADL, tWHR and tRHW
timings instead of returning an error when the maximum clk divisor is
not big enough to provide an appropriate timing.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ONFI spec says that EDO should be enabled if the host drives tRC less
than 30ns, but the code just tests for the tRC_min value extracted from
the timings exposed by the NAND chip not the timings actually configured
in the NAND controller.
Fix that by first rounding down the requested clk_rate with
clk_round_rate() and then checking if tRC is actually smaller than 30ns.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Unlike what is specified in the Allwinner datasheets, the NAND clock rate
is not equal to 2/T but 1/T. Fix the clock rate selection accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
sunxi_nand_chip_set_timings() is extracting a pointer to the nfc from the
nand->controller field, but this field is initialized after
sunxi_nand_chip_set_timings() call.
Reorder the calls to avoid any problem.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
It also contains some minor related changes:
1) Don't warn if kzalloc fails as it dumps stack on its own
2) Use %pR format for displaying whole resource to avoid invalid format
warning
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Some drivers are including linux/of_mtd.h even if they don't use any of
the of_get_nand_xxx() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Harvey Hunt <harvey.hunt@imgtec.com>
If there is only one bit difference in the ECC, the function should
return 1.
The result of "diff0 & ~(1<<fls(diff0))" is equal to diff0, so the
function actually returns -1.
Signed-off-by: Zhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The new IFC controller version 2.0 has a different memory map page.
Upto IFC 1.4 PAGE size is 4 KB and from IFC2.0 PAGE size is 64KB.
This patch segregates the IFC global and runtime registers to appropriate
PAGE sizes.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Raghav Dogra <raghav@freescale.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There's no reason to BUG() when parameters are being
validated. Drivers can get things wrong, and it's much nicer
to just throw a noisy warn and fail gracefully, than calling
BUG() and throwing the whole system down the drain.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
fix the raw_buffer pointer double free issue found by coverify.
CID 18344 (#2 of 2): Double free (USE_AFTER_FREE)
3. double_free: Calling gpmi_alloc_dma_buffer frees pointer
this->raw_buffer which has already been freed
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Document and match the brcm,brcmnand-v6.2 compatible string, the controller has
a register layout identical to the v6.0 version and supports prefetch. Update the
command shift logic to account for v6.2 controller which are the first ones to
use a shift of 0 (6.1 used a shift of 24).
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
bch->dev is already assigned to &pdev->dev in the probe function.
Remove the duplicate assignment done in jz4780_bch_get().
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Acked-by: Harvey Hunt <harvey.hunt@imgtec.com>
New atmel SoCs are able to fix bitflips in erased pages, but old ones
are still impacted by this problem. Use nand_check_erased_ecc_chunk() to
handle this case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Herve Codina <herve.CODINA@celad.com>
Reviewed-by: Herve Codina <herve.CODINA@celad.com>
Tested-by: Herve Codina <herve.CODINA@celad.com>
This follows recent work on switching to enum nand_ecc_algo and
deprecating NAND_ECC_SOFT_BCH.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use recently added of_get_nand_ecc_algo for that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Pull leds-trigger changes from Jacek Anaszewski.
Create a generic mtd led-trigger to replace the exisitng nand led-trigger
implementation.
* 'mtd-nand-trigger' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
mtd: Hook I/O activity to the MTD LED trigger
mtd: nand: Remove the "nand-disk" LED trigger
leds: trigger: Introduce a MTD (NAND/NOR) trigger
mtd: Uninline mtd_write_oob and move it to mtdcore.c
leds: trigger: Introduce a kernel panic LED trigger
The GPMC WAIT pin status are now available over gpiolib.
Update the omap_dev_ready() function to use gpio instead of
directly accessing GPMC register space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Move NAND specific device tree parsing to NAND driver.
The NAND controller node must have a compatible id, register space
resource and interrupt resource.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Copy all the platform data parameters to the driver's local data
structure 'omap_nand_info' and use it in the entire driver. This will
make it easer for device tree migration.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of accessing the gpmc_status register directly start
using the gpmc_nand_ops->nand_writebuffer_empty() helper
to check write buffer empty status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Deprecate nand register passing via platform data and use
gpmc_omap_get_nand_ops() instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that we've added the MTD LED trigger, we need
to call each I/O path to ledtrig_mtd_activity.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit removes the "nand-disk" LED trigger from the
NAND code.
A trigger with the same name is already available selecting
LEDS_TRIGGER_MTD. Note that "nand-disk" trigger is being
deprecated in favor of the "mtd" trigger.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
There's no reason for having mtd_write_oob inlined in mtd.h header.
Move it to mtdcore.c where it belongs.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
NAND:
* Add sunxi_nand randomizer support
* begin refactoring NAND ecclayout structs
* fix pxa3xx_nand dmaengine usage
* brcmnand: fix support for v7.1 controller
* add Qualcomm NAND controller driver
SPI NOR:
* add new ls1021a, ls2080a support to Freescale QuadSPI
* add new flash ID entries
* support bottom-block protection for Winbond flash
* support Status Register Write Protect
* remove broken QPI support for Micron SPI flash
JFFS2:
* improve post-mount CRC scan efficiency
General:
* refactor bcm63xxpart parser, to later extend for NAND
* add writebuf size parameter to mtdram
Other minor code quality improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW9CzVAAoJEFySrpd9RFgtQFwQAJdH0wnsZTYfeqToIaD8yMM4
rtakV/oIMSvMSWuqK+Mx0k6OjGwswgnGZ+tfQLRAYIhb33P8UD0F8Dv5D0x/+zRo
EgiDlnss/lliXpbh2u4fsANSpFF/JUPXFqU6NanjqQ1rtvR60LUeKOFEz1NRciuV
Ib6oDLFeXQFxwG0J+EBDo5MrT8aiPODtx4TS8VVo0o0y/WLkEujQPP5592TnCPha
zX0n9azi26pARo7VLqWjVD8GigY5PadqJAWOZcQr0dGMQv5URtWcCCdThiNsCEzY
SW9cYSr4CBdy1FIeoJ47yoBg8aFzhyeeuF1efb1U0MoYVL0rdIbznop3Kwilj48L
Rnh4hvKkrTH16rO6RfKm1lIJaJQYKMErXyEceYMIjV91fEL3qhfbU9W6+Q5HT4hY
oJmlH+4e/I1Jtf+vW4xFGMYclmYwCO6GJ4HHqnNpby/iH/nZ07hNX3lbxrlqHMwh
MrSIidqLTsseXcyHBFc+42AsWs8unaYWVB0N3VFkEgl0BFyPObAtvwnHA6zywMvp
EqJijXFG8VPcztE3eTIMbd0WOkxTjpMT6YHzpZqli/ENxCgu79OWELYrJ0/vC5Uj
HK0qxgvIzUyJgmikkySDvd/Hc6HWItYonlcAht0VErNfTTfkMwWgRz1W4ZRB6bOJ
7M83aytLyRYaPGEbwaoR
=xOlP
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160324' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
- Add sunxi_nand randomizer support
- begin refactoring NAND ecclayout structs
- fix pxa3xx_nand dmaengine usage
- brcmnand: fix support for v7.1 controller
- add Qualcomm NAND controller driver
SPI NOR:
- add new ls1021a, ls2080a support to Freescale QuadSPI
- add new flash ID entries
- support bottom-block protection for Winbond flash
- support Status Register Write Protect
- remove broken QPI support for Micron SPI flash
JFFS2:
- improve post-mount CRC scan efficiency
General:
- refactor bcm63xxpart parser, to later extend for NAND
- add writebuf size parameter to mtdram
Other minor code quality improvements"
* tag 'for-linus-20160324' of git://git.infradead.org/linux-mtd: (72 commits)
mtd: nand: remove kerneldoc for removed function parameter
mtd: nand: Qualcomm NAND controller driver
dt/bindings: qcom_nandc: Add DT bindings
mtd: nand: don't select chip in nand_chip's block_bad op
mtd: spi-nor: support lock/unlock for a few Winbond chips
mtd: spi-nor: add TB (Top/Bottom) protect support
mtd: spi-nor: add SPI_NOR_HAS_LOCK flag
mtd: spi-nor: use BIT() for flash_info flags
mtd: spi-nor: disallow further writes to SR if WP# is low
mtd: spi-nor: make lock/unlock bounds checks more obvious and robust
mtd: spi-nor: silently drop lock/unlock for already locked/unlocked region
mtd: spi-nor: wait for SR_WIP to clear on initial unlock
mtd: nand: simplify nand_bch_init() usage
mtd: mtdswap: remove useless if (!mtd->ecclayout) test
mtd: create an mtd_oobavail() helper and make use of it
mtd: kill the ecclayout->oobavail field
mtd: nand: check status before reporting timeout
mtd: bcm63xxpart: give width specifier an 'int', not 'size_t'
mtd: mtdram: Add parameter for setting writebuf size
mtd: nand: pxa3xx_nand: kill unused field 'drcmr_cmd'
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
* A simple error code handling fix for the NAND ECC test; this was a
regression in v4.5-rc1
* A MAINTAINERS update, which might as well go in ASAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Got
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160311' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Late MTD fix for v4.5:
- A simple error code handling fix for the NAND ECC test; this was a
regression in v4.5-rc1
- A MAINTAINERS update, which might as well go in ASAP"
* tag 'for-linus-20160311' of git://git.infradead.org/linux-mtd:
MAINTAINERS: add a maintainer for the NAND subsystem
mtd: nand: tests: fix regression introduced in mtd_nandectest
The 'getchip' parameter is gone as of commit 9f3e04297b ("mtd: nand:
don't select chip in nand_chip's block_bad op"), so kill the doc with
it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Qualcomm NAND controller is found in SoCs like IPQ806x, MSM7xx,
MDM9x15 series.
It exists as a sub block inside the IPs EBI2 (External Bus Interface 2)
and QPIC (Qualcomm Parallel Interface Controller). These IPs provide a
broader interface for external slow peripheral devices such as LCD and
NAND/NOR flash memory or SRAM like interfaces.
We add support for the NAND controller found within EBI2. For the SoCs
of our interest, we only use the NAND controller within EBI2. Therefore,
it's safe for us to assume that the NAND controller is a standalone block
within the SoC.
The controller supports 512B, 2kB, 4kB and 8kB page 8-bit and 16-bit NAND
flash devices. It contains a HW ECC block that supports BCH ECC (4, 8 and
16 bit correction/step) and RS ECC(4 bit correction/step) that covers main
and spare data. The controller contains an internal 512 byte page buffer
to which we read/write via DMA. The EBI2 type NAND controller uses ADM DMA
for register read/write and data transfers. The controller performs page
reads and writes at a codeword/step level of 512 bytes. It can support up
to 2 external chips of different configurations.
The driver prepares register read and write configuration descriptors for
each codeword, followed by data descriptors to read or write data from the
controller's internal buffer. It uses a single ADM DMA channel that we get
via dmaengine API. The controller requires 2 ADM CRCIs for command and
data flow control. These are passed via DT.
The ecc layout used by the controller is syndrome like, but we can't use
the standard syndrome ecc ops because of several reasons. First, the amount
of data bytes covered by ecc isn't same in each step. Second, writing to
free oob space requires us writing to the entire step in which the oob
lies. This forces us to create our own ecc ops.
One more difference is how the controller accesses the bad block marker.
The controller ignores reading the marker when ECC is enabled. ECC needs
to be explicity disabled to read or write to the bad block marker. The
nand_bbt helpers library hence can't access BBMs for the controller.
For now, we skip the creation of BBT and populate chip->block_bad and
chip->block_markbad helpers instead.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
One of the arguments passed to struct nand_chip's block_bad op is
'getchip', which, if true, is supposed to get and select the nand device,
and later unselect and release the device.
This op is intended to be replaceable by drivers. The drivers shouldn't
be responsible for selecting/unselecting chip. Like other ops, the chip
should already be selected before the block_bad op is called.
Remove the getchip argument from the block_bad op and
nand_block_checkbad. Move the chip selection to nand_block_isbad, since it
is the only caller to nand_block_checkbad which requires chip selection.
Modify nand_block_bad (the default function for the op) such that it
doesn't select the chip.
Remove the getchip argument from the bad_block funcs in cafe_nand,
diskonchip and docg4 drivers.
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These are recent Winbond models that are known to have lock/unlock
support via writing the Status Register, and that also support the TB
(Top/Bottom) protection bit.
Tested on w25q32dw.
[Note on style: these entries are getting pretty long lines, so I picked
a style that seems reasonable for splitting up the flags separate from
the other mostly-similar fields.]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Some flash support a bit in the status register that inverts protection
so that it applies to the bottom of the flash, not the top. This yields
additions to the protection range table, as noted in the comments.
Because this feature is not universal to all flash that support
lock/unlock, control it via a new flag.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
We can't determine this purely by manufacturer type (see commit
67b9bcd369 ("mtd: spi-nor: fix Spansion regressions (aliased with
Winbond)")), and it's not autodetectable by anything like SFDP. So make
a new flag for it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
It's a little easier to read and make sure there are no collisions
(IMO).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Locking the flash is most useful if it provides real hardware security.
Otherwise, it's little more than a software permission bit.
A reasonable use case that provides real HW security might be like
follows:
(1) hardware WP# is deasserted
(2) program flash
(3) flash range is protected via status register
(4) hardware WP# is asserted
(5) flash protection range can no longer be changed, until WP# is
deasserted
In this way, flash protection is co-owned by hardware and software.
Now, one would expect to be able to perform step (3) with
ioctl(MEMLOCK), except that the spi-nor driver does not set the Status
Register Protect bit (a.k.a. Status Register Write Disable (SRWD)), so
even though the range is now locked, it does not satisfy step (5) -- it
can still be changed by a call to ioctl(MEMUNLOCK).
So, let's enable status register protection after the first lock
command, and disable protection only when the flash is fully unlocked.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
There are a few different corner cases to the current logic that seem
undesirable:
* mtd_lock() with offs==0 trips a bounds issue on
ofs - mtd->erasesize < 0
* mtd_unlock() on the middle of a flash that is already unlocked will
return -EINVAL
* probably other corner cases
So, let's stop doing "smart" checks like "check the block below us",
let's just do the following:
(a) pass only non-negative offsets/lengths to stm_is_locked_sr()
(b) add a similar stm_is_unlocked_sr() function, so we can check if the
*entire* range is unlocked (and not just whether some part of it is
unlocked)
Then armed with (b), we can make lock() and unlock() much more
symmetric:
(c) short-circuit the procedure if there is no work to be done, and
(d) check the entire range above/below
This also aligns well with the structure needed for proper TB
(Top/Bottom) support.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
If, for instance, the entire flash is already unlocked and I try to
mtd_unlock() the entire device, I don't expect to see an EINVAL error.
It should just silently succeed. Ditto for mtd_lock().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Fixup a piece leftover by commit 32321e950d ("mtd: spi-nor: wait until
lock/unlock operations are ready"). That commit made us wait for the WIP
bit to settle after lock/unlock operations, but it missed the open-coded
"unlock" that happens at probe() time.
We should probably have this code utilize the unlock() routines in the
future, to avoid duplication, but unfortunately, flash which need to be
unlocked don't all have a proper ->flash_unlock() callback.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Stas Sergeev <stsp@users.sourceforge.net>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
nand_bch_init() requires several arguments which could directly be deduced
from the mtd device. Get rid of those useless parameters.
nand_bch_init() is also requiring the caller to provide a proper eccbytes
value, while this value could be deduced from the ecc.size and
ecc.strength value. Fallback to eccbytes calculation when it is set to 0.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If the MTD device does not have OOB, the mtd->oobsize and mtd->oobavail
fields are set to zero, and we are testing those values in the following
test.
Remove the useless if (!mtd->ecclayout) test.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently, all MTD drivers/sublayers exposing an OOB area are
doing the same kind of test to extract the available OOB size
based on the mtd_info and mtd_oob_ops structures.
Move this common logic into an inline function and make use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Suggested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ecclayout->oobavail is just redundant with the mtd->oobavail field.
Moreover, it prevents static const definition of ecc layouts since the
NAND framework is calculating this value based on the ecclayout->oobfree
field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit b70af9bef4 ("mtd: nand: increase ready wait timeout and
report timeouts"), we increased the likelihood of scheduling during
nand_wait(). This makes us more likely to hit the time_before(...)
condition, since a lot of time may pass before we get scheduled again.
Now, the loop was already buggy, since we don't check if the NAND is
ready after exiting the loop; we simply print out a timeout warning. Fix
this by doing a final status check before printing a timeout message.
This isn't actually a critical bug, since the only effect is a false
warning print. But too many prints never hurt anyone, did they? :)
Side note: perhaps I'm not smart enough, but I'm not sure what the best
policy is for this kind of loop; do we busy loop (i.e., no
cond_resched()) to keep the lowest I/O latency (it's not great if the
resched is delaying Richard's system ~400ms)? Or do we allow
rescheduling, to play nice with the rest of the system (since some
operations can take quite a while)?
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Harvey Hunt <harvey.hunt@imgtec.com>
Fixes this warning:
>> drivers/mtd/bcm63xxpart.c:175:4: note: in expansion of macro 'pr_err'
pr_err("invalid rootfs address: %*ph\n",
^
>> include/linux/kern_levels.h:4:18: warning: field width specifier '*' expects argument of type 'int', but argument 2 has type 'long unsigned int' [-Wformat=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ubifs uses the write buffer size in recovery algorithm. When inspecting
an unclean ubifs recovery fails with writebuf size 64 in mtdram while
recovery on actual mtd device with writebuf size of 1024 succeeds.
So add a parameter for setting this property.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With this removal, we don't need to 'get' the second DMA resource
either, as it's also unused.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
LS1043a and LS2080A in the Layerscape family also support Freescale Quad
SPI, make Quad SPI selectable for these hardwares.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
LS1021a also support Freescale Quad SPI controller.
Add fsl-quadspi support for ls1021a chip and make SPI_FSL_QUADSPI
selectable for LS1021A SOC hardwares.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Han xu <han.xu@freescale.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add R/W functions for big- or little-endian registers:
The qSPI controller's endian is independent of the CPU core's endian.
So far, the qSPI have two versions for big-endian and little-endian.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Han xu <han.xu@freescale.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ubi_start_leb_change() allocates too few bytes.
ubi_more_leb_change_data() will write up to req->upd_bytes +
ubi->min_io_size bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Micron n25q128axx support subsector (4K) erase so let's update the flags.
Tested on n25q128a13.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the driver is initialized in a pure device-tree platform, the
driver's probe fails allocating the dma channel :
[ 525.624435] pxa3xx-nand 43100000.nand: no resource defined for data DMA
[ 525.632088] pxa3xx-nand 43100000.nand: alloc nand resource failed
The reason is that the DMA IO resource is not acquired through platform
resources but by OF bindings.
Fix this by ensuring that DMA IO resources are only queried in the non
device-tree case.
Fixes: 8f5ba31aa5 ("mtd: nand: pxa3xx-nand: switch to dmaengine")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Offending Commit: 6e94119 "mtd: nand: return consistent error codes in
ecc.correct() implementations"
The new error code was not being handled properly in double bit error
detection.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd->priv is no longer pointing to the struct nand_chip it is attached to.
Replace those accesses by mtd_to_nand() calls.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 4be4e03efc ("mtd: nand: sunxi: add randomizer support")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The BRCMNAND controller revision 7.1 is almost 100% compatible with the
previous v6.0 register offset layout, except for the Correctable Error
Reporting Threshold registers. Fix this by adding another table with the
correct offsets for CORR_THRESHOLD and CORR_THRESHOLD_EXT.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 5942ddbc50 ("mtd: introduce mtd_block_markbad interface")
incorrectly changed onenand_block_markbad() to call mtd_block_markbad
instead of onenand_chip's block_markbad function. As a result the function
will now recurse and deadlock. Fix by reverting the change.
Fixes: 5942ddbc50 ("mtd: introduce mtd_block_markbad interface")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
