Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.
Fix by doing correct ring accounting in setup call.
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.
With this new flag we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76dc ("net:add one common config...") did,
so revert this commit.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.
Fixes: a21d0822ff ("ixgbe: add support for geneve Rx offload")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I increased the scale of supported VRFs by having
all of them share the same LPM tree.
In order to avoid look-ups for prefix lengths that don't exist, each
route removal would trigger an aggregation across all the active virtual
routers to see which prefix lengths are in use and which aren't and
structure the tree accordingly.
With the way the data structures are currently laid out, this is a very
expensive operation. When preformed repeatedly - due to the invocation
of the abort mechanism - and with enough VRFs, this can result in a hung
task.
For now, avoid this optimization until it can be properly re-added in
net-next.
Fixes: fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ppp_release() tries to ensure that netdevices are unregistered before
decrementing the unit refcount and running ppp_destroy_interface().
This is all fine as long as the the device is unregistered by
ppp_release(): the unregister_netdevice() call, followed by
rtnl_unlock(), guarantee that the unregistration process completes
before rtnl_unlock() returns.
However, the device may be unregistered by other means (like
ppp_nl_dellink()). If this happens right before ppp_release() calling
rtnl_lock(), then ppp_release() has to wait for the concurrent
unregistration code to release the lock.
But rtnl_unlock() releases the lock before completing the device
unregistration process. This allows ppp_release() to proceed and
eventually call ppp_destroy_interface() before the unregistration
process completes. Calling free_netdev() on this partially unregistered
device will BUG():
------------[ cut here ]------------
kernel BUG at net/core/dev.c:8141!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 1557 Comm: pppd Not tainted 4.14.0-rc2+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
Call Trace:
ppp_destroy_interface+0xd8/0xe0 [ppp_generic]
ppp_disconnect_channel+0xda/0x110 [ppp_generic]
ppp_unregister_channel+0x5e/0x110 [ppp_generic]
pppox_unbind_sock+0x23/0x30 [pppox]
pppoe_connect+0x130/0x440 [pppoe]
SYSC_connect+0x98/0x110
? do_fcntl+0x2c0/0x5d0
SyS_connect+0xe/0x10
entry_SYSCALL_64_fastpath+0x1a/0xa5
RIP: free_netdev+0x107/0x110 RSP: ffffc28a40573d88
---[ end trace ed294ff0cc40eeff ]---
We could set the ->needs_free_netdev flag on PPP devices and move the
ppp_destroy_interface() logic in the ->priv_destructor() callback. But
that'd be quite intrusive as we'd first need to unlink from the other
channels and units that depend on the device (the ones that used the
PPPIOCCONNECT and PPPIOCATTACH ioctls).
Instead, we can just let the netdevice hold a reference on its
ppp_file. This reference is dropped in ->priv_destructor(), at the very
end of the unregistration process, so that neither ppp_release() nor
ppp_disconnect_channel() can call ppp_destroy_interface() in the interim.
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Fixes: 8cb775bc0a ("ppp: fix device unregistration upon netns deletion")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently handles two NVM formats,
one for 7000 family and below, and one for 8000 family and above.
The 3168 series uses something in between,
so currently the driver uses incorrect offsets for it.
Fix the incorrect offsets.
Fixes: c4836b056d ("iwlwifi: Add PCI IDs for the new 3168 series")
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current channel flags printing is very strange and messy,
in LAR we sometimes print the channel number and sometimes the
frequency, in both we print a calculated value (whether ad-hoc
is supported or not) etc.
Unify all this to
* print the channel number, not the frequency
* remove the band print (2.4/5.2 GHz, it's obvious)
* remove the calculated Ad-Hoc print
Doing all of this also gets the length of the string to a max
of 101 characters, which is below the max of 110 for tracing,
and thus avoids the warning that came up on certain channels
with certain flag combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It seems that libsensors treats -EIO as a special non-recoverable
failure when it tries to read the temperature while the firmware is
not running. To solve that, change the error code to a milder
-ENODATA.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196941
Fixes: c221daf219 ("iwlwifi: mvm: add registration to thermal zone")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today we stop the device and the DMA without stopping the dbgc
recording before. This causes host crashes when the DMA
rate is high.
Stop dbgc recording when clearing the fw debug configuration
to fix this.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In monitor mode we are not expected to decrypt encrypted
packets (not having the keys).
Hence we are expected to get an unknown rx security status.
Keeping the print in monitor mode causes a print for each
captured packet flooding the dmesg.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add constants and callback functions for the dwmac on rk3128 soc.
As can be seen, the base structure is the same, only registers
and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat the ef/04/01 interface class/subclass/protocol combination used
by the Novatel Verizon USB730L (1410:9030) as a possible RNDIS
interface.
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 3
P: Vendor=1410 ProdID=9030 Rev=03.10
S: Manufacturer=Novatel Wireless
S: Product=MiFi USB730L
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
I: If#= 2 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
Once the network interface is brought up, the user just needs to run a
DHCP client to get IP address and routing setup.
As a side note, other Novatel Verizon USB730L models with the same
vid:pid end up exposing a standard ECM interface which doesn't require
any other kernel update to make it work.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When considering whether to set RTNH_F_OFFLOAD flag on an IPv6 route,
mlxsw_sp_fib6_entry_offload_set() looks up the mlxsw_sp_nexthop
corresponding to a given route, and decides based on whether the next
hop's offloaded flag was set. When looking for the matching next hop, it
also takes into account the device of the route, which must match next
hop's RIF.
IPIP next hops however hitherto didn't set the RIF. As a result, IPv6
routes forwarding traffic to IP-in-IP netdevices are never marked as
offloaded, even when they actually are.
Thus track RIF of IPIP next hops the same way as that of ETHERNET next
hops.
Fixes: 8f28a30976 ("mlxsw: spectrum_router: Support IPv6 overlay encap")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a new RIF, bumping RIF count of the containing VR is the
last thing to be done. Symmetrically, when destroying a RIF, RIF count
is first dropped and only then the rest of the cleanup proceeds.
That's a problem for loopback RIFs. Those hold two VR references: one
for overlay and one for underlay. mlxsw_sp_rif_destroy() releases the
overlay one, and the deconfigure() callback the underlay one. But if
both overlay and underlay are the same, and if there are no other
artifacts holding the VR alive, this put actually destroys the VR. Later
on, when mlxsw_sp_rif_destroy() calls mlxsw_sp_vr_put() for the same VR,
the VR will already have been released and the kernel crashes with NULL
pointer dereference.
The underlying problem is that the RIF under destruction ends up
referencing the overlay VR much longer than it claims: all the way until
the call to mlxsw_sp_vr_put(). So line up the reference counting
properly to reflect this. Make corresponding changes in
mlxsw_sp_rif_create() as well for symmetry.
Fixes: 6ddb7426a7 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With KASAN and a couple of other patches applied, this driver is one
of the few remaining ones that actually use more than 2048 bytes of
kernel stack:
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy_gainctrl':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:16065:1: warning: the frame size of 3264 bytes is larger than 2048 bytes [-Wframe-larger-than=]
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:17138:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Here, I'm reducing the stack size by marking as many local variables as
'static const' as I can without changing the actual code.
This is the first of three patches to improve the stack usage in this
driver. It would be good to have this backported to stabl kernels
to get all drivers in 'allmodconfig' below the 2048 byte limit so
we can turn on the frame warning again globally, but I realize that
the patch is larger than the normal limit for stable backports.
The other two patches do not need to be backported.
Cc: <stable@vger.kernel.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of the data in the received skb is currently passed into
brcmf_fweh_process_event() as packet_len, but this value is not checked.
event_packet should be followed by DATALEN bytes of additional event
data. Ensure that the received packet actually contains at least
DATALEN bytes of additional data, to avoid copying uninitialized memory
into event->data.
Cc: <stable@vger.kernel.org> # v3.8
Suggested-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 40b368af4b ("rtlwifi: Fix alignment issues"), the read
of REG_DBI_READ was changed from 16 to 8 bits. For unknown reasonsi
this change results in reduced stability for the wireless connection.
This regression was located using bisection.
Fixes: 40b368af4b ("rtlwifi: Fix alignment issues")
Reported-and-tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.11+
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If this sanity check fails, we must free 'rss_indir'. Otherwise there is a
memory leak.
'goto err' as done in the other error handling paths to fix it.
Fixes: 46a3df9f97 ("net: hns3: Fix for setting rss_size incorrectly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This linksys dongle by default comes up in cdc_ether mode.
This patch allows r8152 to claim the device:
Bus 002 Device 002: ID 13b1:0041 Linksys
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g2_irq_free locks the registers mutex, but not
mv88e6xxx_g1_irq_free, which results in a stack trace from
assert_reg_lock when unloading the mv88e6xxx module. Fix this.
Fixes: 3460a5770c ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-enable the MAC receiver by setting CONFIG_RE before powering down,
as instructed in section 6.3.5.1 of [1]. Without this the MAC fails
to receive WoL packets and never wakes up.
[1] DWC Ethernet QoS Databook 4.10a October 2014
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hook to stmmac_pltfr_pm_ops for suspend / resume handling.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports with the same VLAN must all be in the same bridge. However the
CPU and DSA ports need to be in multiple VLANs spread over multiple
bridges. So exclude them when performing this test.
Fixes: b2f81d304c ("net: dsa: add CPU and DSA ports as VLAN members")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch stops the internal MAC Tx clock from being enabled as the
internal clock isn't used. The definition used for the bit controlling
this behaviour is renamed as well as it was wrongly named (bit 4 of
GMAC_CTRL_2_REG).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private port_list array has a list of pointers to mvpp2_port
instances. This list is allocated given the number of ports enabled in
the device tree, but the pointers are set using the port-id property. If
on a single port is enabled, the port_list array will be of size 1, but
when registering the port, if its id is not 0 the driver will crash.
Other crashes were encountered in various situations.
This fixes the issue by using an index not equal to the value of the
port-id property.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parsing fragmentation detection failed due to wrong configured
parser TCAM entry's. Some traffic was marked as fragmented in RX
descriptor, even it wasn't IP fragmented. The hardware also failed to
calculate checksums which lead to use software checksum and caused
performance degradation.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calculating the offloads counters, count them explicitly.
The calculations done for these counters would result in bugs in some
cases, for example:
When running TCP traffic over a VXLAN tunnel with TSO enabled the following
counters would increase:
tx_csum_partial: 1,333,284
tx_csum_partial_inner: 29,286
tx4_csum_partial_inner: 384
tx7_csum_partial_inner: 8
tx9_csum_partial_inner: 34
tx10_csum_partial_inner: 26,807
tx11_csum_partial_inner: 287
tx12_csum_partial_inner: 27
tx16_csum_partial_inner: 6
tx25_csum_partial_inner: 1,733
Seems like tx_csum_partial increased out of nowhere.
The issue is in the following calculation in mlx5e_update_sw_counters:
s->tx_csum_partial = s->tx_packets - tx_offload_none - s->tx_csum_partial_inner;
While tx_packets increases by the number of GSO segments for each SKB,
tx_csum_partial_inner will only increase by one, resulting in wrong
tx_csum_partial counter.
Fixes: bfe6d8d1d4 ("net/mlx5e: Reorganize ethtool statistics")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Toggling of C-tag VLAN filter should not affect the "any S-tag" steering rule.
Fixes: 8a271746a2 ("net/mlx5e: Receive s-tagged packets in promiscuous mode")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the correct formatting for netdev features.
Fixes: 0e405443e8 ("net/mlx5e: Improve set features ndo resiliency")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Encap entries cached by the driver could be invalidated due to
tunnel destination neighbour state changes.
When attempting to offload a flow that uses a cached encap entry,
we must check the entry validity and defer the offloading
if the entry exists but not valid.
When EAGAIN is returned, the flow offloading to hardware takes place
by the neigh update code when the tunnel destination neighbour
becomes connected.
Fixes: 232c001398 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When offloading header re-write, the HW may need to adjust checksums along
the packet. For IP traffic, and a case where we are asked to modify fields in
the IP header, current HW supports that only for TCP and UDP. Enforce it, in
this case fail the offloading attempt for non TCP/UDP packets.
Fixes: d7e75a325c ('net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions')
Fixes: 2f4fe4cab0 ('net/mlx5e: Add offloading of NIC TC pedit (header re-write) actions')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case the neighbour for the tunnel destination isn't valid,
we send a neighbour update request but we free the encap
header buffer. This is wrong, because we still need it for
allocating a HW encap entry once the neighbour is available.
Fix that by skipping freeing it if we wait for neighbour.
Fixes: 232c001398 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added check for the maximal number of flow counters attached
to rule (FTE).
Fixes: bd5251dbf1 ('net/mlx5_core: Introduce flow steering destination of type counter')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, FPGA capability is located in (mdev)->caps.hca_cur,
change the location to be (mdev)->caps.fpga,
since hca_cur is reserved for HCA device capabilities.
Fixes: e29341fb3a ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When cleaning rdma netdevice we need to save the mdev pointer
because priv is released when we release netdev.
This bug was found using the kernel address sanitizer (KASAN).
use-after-free in mlx5_rdma_netdev_free+0xe3/0x100 [mlx5_core]
Fixes: 48935bbb7a ("net/mlx5e: IPoIB, Add netdevice profile skeleton")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Quite a lot of fixes this time. Most notable is the brcmfmac fix for a
CVE issue.
iwlwifi
* a couple of bugzilla bugs related to multicast handling
* two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems
* two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch
* a fix for buffer reordering in the newly supported 9000 device
family
* fix a race when starting aggregation
* small fix for a recent patch to wake mac80211 queues
* send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save
ath10k
* fix a PCI PM related gcc warning
brcmfmac
* CVE-2017-0786: add length check scan results from firmware
* respect passive scan requests from user space
qtnfmac
* fix race in tx path when using multiple interfaces
* cancel ongoing scan when removing the wireless interface
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZyMFDAAoJEG4XJFUm622bKcwIAJrA+WBwvQUChcFGc5KWUaqB
+aJN1fP3AaiLHVU0Ny1jNIPYPREH9/EejCI72i2WE5TH73sAbqL/XPn8Y5pETQ25
FvKSnTZJyjbU0PNa5pgdYVDr+ZJ21z4hD9OdSRib6Ru62o21ISqzsT5bqd9g3btX
KRDqaAqkQYiMpL73KuF+89RmeUjXNM0GFbdxvziRV3mKYqqZiqNNQLxKlPOCcAD0
2AOyX+k2FLiG5+/RvrcLiCjUzwzQzxwhwQZe1w+ncFRX5INvESLWHDWyzYcB5C0M
9iKc6QVaWTFGqsVyGk+M2decKuj5wHaPVMGc3g7FYWBJo/CVsmpW+kbNrJ/FG08=
=s1IH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Quite a lot of fixes this time. Most notable is the brcmfmac fix for a
CVE issue.
iwlwifi
* a couple of bugzilla bugs related to multicast handling
* two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems
* two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch
* a fix for buffer reordering in the newly supported 9000 device
family
* fix a race when starting aggregation
* small fix for a recent patch to wake mac80211 queues
* send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save
ath10k
* fix a PCI PM related gcc warning
brcmfmac
* CVE-2017-0786: add length check scan results from firmware
* respect passive scan requests from user space
qtnfmac
* fix race in tx path when using multiple interfaces
* cancel ongoing scan when removing the wireless interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_frag_dma_map multiple times if tx length is greater than
device max and avoid processing tx ring until entire packet has been
sent.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a bug in aquantia atlantic card firmware, it sometimes reports
invalid link speed bits. That caused driver to report link down events,
although link itself is totally fine.
This patch ignores such out of blue readings.
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver did a poor job in managing its Tx queues: Sometimes it could stop
tx queues due to link down condition in aq_nic_xmit - but never waked up
them. That led to Tx path total suspend.
This patch fixes this and improves generic queue management:
- introduces queue restart counter
- uses generic netif_ interface to disable and enable tx path
- refactors link up/down condition and introduces dmesg log event when
link changes.
- introduces new constant for minimum descriptors count required for queue
wakeup
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although hardware is capable for almost 16K MTU, without max_mtu field
correctly set it only allows standard MTU to be used.
This patch enables max MTU, calculating it from hardware maximum frame size
of 16352 octets (including FCS).
Fixes: 5513e16421 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inlining these functions creates lots of stack variables that each take
64 bytes when KASAN is enabled, leading to this warning about potential
stack overflow:
drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_cmd_flow_tbl_add':
drivers/net/ethernet/rocker/rocker_ofdpa.c:621:1: error: the frame size of 2752 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
gcc-8 can now consolidate the stack slots itself, but on older versions
we get the same behavior by using a temporary variable that holds a
copy of the inline function argument.
Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mapping the RX DMA buffers, the driver was accidentally specifying
zero for the buffer length. Under normal circumstances, SWIOTLB does not
need to allocate a bounce buffer, so the address is just mapped without
checking the size field. This is why the error was not detected earlier.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the error handling paths 'goto error', except this one.
We should also go to error in this case, or some resources will be
leaking.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is
not enough to represent interrupt numbers on all architectures. Hence
PHY interrupt numbers may be truncated during printing.
Increase the buffer size from 4 to 8 bytes to fix this.
Fixes: 5e369aefdc ("net: stmmac: Delete dead code for MDIO registration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use default value of auto duplex and auto speed values loaded
from EEPROM/OTP after reset. The LAN78xx allows platform
configurations to be loaded from EEPROM/OTP.
Ex: When external phy is connected, the MAC can be configured to
have correct auto speed, auto duplex, auto polarity configured
from the EEPROM/OTP.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow EEPROM write for less than MAX_EEPROM_SIZE
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for eeprom read/write when device auto suspend
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 2d55173e71 ("phy: add generic function to support
ksetting support"), we lost the ability to report the transceiver type
like we used to. Now that we have added back the transceiver type to
ethtool_link_settings, we can report it back like we used to and have no
loss of information.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC has the option of sending only a single pause frame when
flow control is enabled and the RX queue is full. Although sending
only one pause frame has little value, this would allow admins to
enable automatic flow control without having to worry about the EMAC
flooding nearby switches with pause frames if the kernel hangs.
The option is enabled by using the single-pause-mode private flag.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MTU is changed the host would reject the send buffer change.
This problem is result of recent change to allow changing send
buffer size.
Every time we change the MTU, we store the previous net_device section
count before destroying the buffer, but we don’t store the previous
section size. When we reinitialize the buffer, its size is calculated
by multiplying the previous count and previous size. Since we
continuously increase the MTU, the host returns us a decreasing count
value while the section size is reinitialized to 1728 bytes every
time.
This eventually leads to a condition where the calculated buf_size is
so small that the host rejects it.
Fixes: 8b5327975a ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is disabled, we get a compile-time
warning:
drivers/net/wireless/ath/ath10k/pci.c:3417:12: error: 'ath10k_pci_pm_resume' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/pci.c:3401:12: error: 'ath10k_pci_pm_suspend' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_suspend(struct device *dev)
Rather than fixing the #ifdef, this just marks both functions
as __maybe_unused, which is a more robust way to do this.
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current mapping between pri and tc is one to one,
so user can't map multi priorities to the same tc.
This patch changes the mapping to many to one.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rss_size is 1, 2, 4, 8, 16, 32, 64, 128, but acutal tc queue
size can be any u16 less than 128. If tc queue size is 5, we
set the rss_size to 8, indirection table will be used to limit
the size of actual queue size.
It may cause dropping of receiving packet in hardware if
rss_size is not set correctly.
For now, each TC has the same rss size.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo error for feild, which should be field.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hdev doesn't support DCB, rx private buffer is not allocated,
otherwise there is not enough buffer for rx shared buffer, causing
buffer allocation process to fail.
This patch fixes by checking the dcb capability in
hclge_rx_buffer_calc.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_priv_buf_alloc is used to tell hardware how much buffer is
used for rx direction, right now only the private buffer is
assigned.
For ae_dev that doesn't support DCB, private rx buffer is assigned
to zero, only shared rx buffer is used. So not setting the shared
rx buffer cause dropping of packet in SSU.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rx private buffer is disabled, there may be some case that
the rx private buffer is not set to zero, which may cause buffer
allocation process to fail.
This patch fixes this problem by setting priv->enable to 0 and
priv->buf_size to zero when rx private buffer is disabled.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ae_dev doesn't support DCB, DEFAULT_DV must be set to
a lower value, otherwise the buffer allocation process will
fail.
This patch fix it by setting it to 30K bytes.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ae_dev doesn't support DCB, rx_priv_wl_config,
common_thrd_config and tm_qs_bp_cfg can't be called, otherwise
cmd return fail, which causes the hclge module initialization
process to fail.
This patch fix it by adding a DCB capability flag to check if
the ae_dev support DCB.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the ROCE supported flag in the driver_data
field of pci_device_id, delete roce_pci_tbl and change
HNAE_DEV_SUPPORT_ROCE_B to HNAE3_DEV_SUPPORT_ROCE_B.
This cleanup is done in order to support adding capability
in pci_device_id and to fix initialization failure when
cmd is not supported.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused
an interrupt. Don't return IRQ_NONE in this case.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC_ENET_TS_TIMER is not checked in the interrupt routine
so there is no need to enable it.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before queue 0 was always checked if any queue caused an interrupt.
It is better to just mark queue 0 if queue 0 has caused an interrupt.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cancel active scans and deactivate firmware scan watchdog timer
when wireless interface configuration is changed. The usecases
include wireless interface mode change, interface down,
AP stop, virtual interface removal.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix tx path regression. Lock should be held when queuing packets
to h/w fifos in order to properly handle configurations with
multiple enabled interfaces.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver was not properly configuring firmware with regard to the
type of scan. It always performed an active scan even when user-space
was requesting for passive scan, ie. the scan request was done without
any SSIDs specified.
Cc: stable@vger.kernel.org # v4.0.x
Reported-by: Huang, Jiangyang <Jiangyang.Huang@itron.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon handling the firmware notification for scans the length was
checked properly and may result in corrupting kernel heap memory
due to buffer overruns. This fix addresses CVE-2017-0786.
Cc: stable@vger.kernel.org # v4.0.x
Cc: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch is pretty much a carbon copy of
commit 3079c65214 ("caif: Fix napi poll list corruption")
with "caif" replaced by "emac".
The commit d75b1ade56 ("net: less interrupt masking in NAPI")
breaks emac.
It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty. However, like some
other drivers emac tries to do a last-ditch check and if there is
more work it will call napi_reschedule and then immediately process
some of this new work. Should the entire budget be consumed while
processing such new work then we will violate the new caller
contract.
This patch fixes this by not touching any work when we reschedule
in emac.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When register/unregister ae_dev, ae_dev should match all client
in the client_list. Enet and roce can co-exists together so we
should continue checking for enet and roce presence together.
So break should not be there.
Above caused problems in loading and unloading of modules.
Fixes: 38eddd126772 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no vlan id in the packets, hardware will treat the vlan id
as 0 and look for the mac_vlan table. This patch set the default vlan id
of PF as 0. Without this config, it will fail when look for mac_vlan
table, and hardware will drop packets.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the ethernet address copy instance with more
appropriate ether_addr_copy() function.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the initialization of MAC address, fetched from HNS3
firmware i.e. when it is not randomly generated, to the HNS3 hardware.
Fixes: ca60906d2795 ("net: hns3: Add support of HNS3 Ethernet Driver for
hip08 SoC")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the vector-to-ring map and unmap command and adds
INT_GL(for, Gap Limiting Interrupts) and VF id to it as required
by the hardware interface.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the IMP command being used to unmap the vector
from the corresponding ring.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default phy address of every port is 0. Therefore, phy address for
each port need to be fetched from firmware and device initialized
with fetched non-default phy address.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the integration of PHYLINK, the configuration option which
used to be under the PHY infrastructure menu in menuconfig ended
up one level up (the network device driver section)
By placing PHYLINK option right after PHYLIB entry, it broke the
way Kconfig used to build the menu. See kconfig-language.txt, section
"Menu structure", 2nd method.
This is fixed by placing the PHYLINK option just before PHYLIB.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several problems with commit 10377ba767 ("net: systemport:
Support 64bit statistics", first one got fixed in 7095c97345 ("net:
systemport: Fix 64-bit stats deadlock").
The second problem is that this specific code updates the
stats64.tx_{packets,bytes} from ndo_get_stats64() and that is what we
are returning to ethtool -S. If we are not running a tool that involves
calling ndo_get_stats64(), then we won't get updated ethtool stats.
The solution to this is to update the stats from both call sites,
factoring that into a specific function, While at it, don't just check
the sizeof() but also the type of the statistics in order to use the
64-bit stats seqlock.
Fixes: 10377ba767 ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems we have to be more careful in napi_complete_done()
use. This patch is not a revert, as it seems we can
avoid bug that Ville reported by moving the napi_complete_done()
test in the spinlock section.
Many thanks to Ville for detective work and all tests.
Fixes: 617f01211b ("8139too: use napi_complete_done()")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ingress-only qdisc for flower offload, as other qdiscs
are not supported for flower offload.
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clear Speed Selection in MDIO control register(0x10),
ie, clear bits 6 and 13 to zero while keeping other bits same.
Before AND operation,The Mask value has to be perform with bitwise NOT
operation (ie, ~ operator)
This patch clears current speed selection before writing the
new speed settings to gmii2rgmii converter
Fixes: f411a6160b ("net: phy: Add gmiitorgmii converter support")
Signed-off-by: Fahad Kunnathadi <fahad.kunnathadi@dexceldesigns.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
* A couple of bugzilla bugs related to multicast handling;
* Two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems;
* Two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch;
* A fix for buffer reordering in the newly supported 9000 device
family;
* Fix a race when starting aggregation;
* Small fix for a recent patch to wake mac80211 queues;
* Send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save;
-----BEGIN PGP SIGNATURE-----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=DM5q
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-09-15' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
First set of fixes for 4.14
* A couple of bugzilla bugs related to multicast handling;
* Two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems;
* Two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch;
* A fix for buffer reordering in the newly supported 9000 device
family;
* Fix a race when starting aggregation;
* Small fix for a recent patch to wake mac80211 queues;
* Send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save;
Pull networking fixes from David Miller:
1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.
2) Fix double-free in rmnet driver, from Dan Carpenter.
3) INET connection socket layer can double put request sockets, fix
from Eric Dumazet.
4) Don't match collect metadata-mode tunnels if the device is down,
from Haishuang Yan.
5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
be2net driver, from Suresh Reddy.
6) Fix scaling error in gen_estimator, from Eric Dumazet.
7) Fix 64-bit statistics deadlock in systemport driver, from Florian
Fainelli.
8) Fix use-after-free in sctp_sock_dump, from Xin Long.
9) Reject invalid BPF_END instructions in verifier, from Edward Cree.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
Documentation: link in networking docs
tcp: fix data delivery rate
bpf/verifier: reject BPF_ALU64|BPF_END
sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
sctp: fix an use-after-free issue in sctp_sock_dump
netvsc: increase default receive buffer size
tcp: update skb->skb_mstamp more carefully
net: ipv4: fix l3slave check for index returned in IP_PKTINFO
net: smsc911x: Quieten netif during suspend
net: systemport: Fix 64-bit stats deadlock
net: vrf: avoid gcc-4.6 warning
qed: remove unnecessary call to memset
tg3: clean up redundant initialization of tnapi
tls: make tls_sw_free_resources static
sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
MAINTAINERS: review Renesas DT bindings as well
net_sched: gen_estimator: fix scaling error in bytes/packets samples
nfp: wait for the NSP resource to appear on boot
nfp: wait for board state before talking to the NSP
...
The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.
This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.
Fixes: 65e65ec137 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Andreas Rammhold <andreas@rammhold.de>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default receive buffer size was reduced by recent change
to a value which was appropriate for 10G and Windows Server 2016.
But the value is too small for full performance with 40G on Azure.
Increase the default back to maximum supported by host.
Fixes: 8b5327975a ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network interface is kept running during suspend, the net core
may call net_device_ops.ndo_start_xmit() while the Ethernet device is
still suspended, which may lead to a system crash.
E.g. on sh73a0/kzm9g and r8a73a4/ape6evm, the external Ethernet chip is
driven by a PM controlled clock. If the Ethernet registers are accessed
while the clock is not running, the system will crash with an imprecise
external abort.
As this is a race condition with a small time window, it is not so easy
to trigger at will. Using pm_test may increase your chances:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo platform > /sys/power/pm_test
# echo mem > /sys/power/state
To fix this, make sure the network interface is quietened during
suspend.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.
[ 5.780350] ================================
[ 5.784679] WARNING: inconsistent lock state
[ 5.789011] 4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[ 5.794561] --------------------------------
[ 5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 5.810175] (&syncp->seq#2){+.?...}, at: [<c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[ 5.818327] {SOFTIRQ-ON-W} state was registered at:
[ 5.823278] bcm_sysport_get_stats64+0x17c/0x258
[ 5.828053] dev_get_stats+0x38/0xac
[ 5.831776] rtnl_fill_stats+0x30/0x118
[ 5.835761] rtnl_fill_ifinfo+0x538/0xe24
[ 5.839921] rtmsg_ifinfo_build_skb+0x6c/0xd8
[ 5.844430] rtmsg_ifinfo_event.part.5+0x14/0x44
[ 5.849201] rtmsg_ifinfo+0x20/0x28
[ 5.852837] register_netdevice+0x628/0x6b8
[ 5.857171] register_netdev+0x14/0x24
[ 5.861051] bcm_sysport_probe+0x30c/0x438
[ 5.865280] platform_drv_probe+0x50/0xb0
[ 5.869418] driver_probe_device+0x2e8/0x450
[ 5.873817] __driver_attach+0x104/0x120
[ 5.877871] bus_for_each_dev+0x7c/0xc0
[ 5.881834] bus_add_driver+0x1b0/0x270
[ 5.885797] driver_register+0x78/0xf4
[ 5.889675] do_one_initcall+0x54/0x190
[ 5.893646] kernel_init_freeable+0x144/0x1d0
[ 5.898135] kernel_init+0x8/0x110
[ 5.901665] ret_from_fork+0x14/0x2c
[ 5.905363] irq event stamp: 24263
[ 5.908804] hardirqs last enabled at (24262): [<c08eecf0>] net_rx_action+0xc4/0x4e4
[ 5.916624] hardirqs last disabled at (24263): [<c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[ 5.925143] softirqs last enabled at (24258): [<c022a7fc>] irq_enter+0x84/0x98
[ 5.932524] softirqs last disabled at (24259): [<c022a918>] irq_exit+0x108/0x16c
[ 5.939985]
[ 5.939985] other info that might help us debug this:
[ 5.946576] Possible unsafe locking scenario:
[ 5.946576]
[ 5.952556] CPU0
[ 5.955031] ----
[ 5.957506] lock(&syncp->seq#2);
[ 5.960955] <Interrupt>
[ 5.963604] lock(&syncp->seq#2);
[ 5.967227]
[ 5.967227] *** DEADLOCK ***
[ 5.967227]
[ 5.973222] 1 lock held by swapper/0/0:
[ 5.977092] #0: (&(&ring->lock)->rlock){..-...}, at: [<c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54
So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.
Fixes: 10377ba767 ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building an allmodconfig kernel with gcc-4.6, we get a rather
odd warning:
drivers/net/vrf.c: In function ‘vrf_ip6_input_dst’:
drivers/net/vrf.c:964:3: error: initialized field with side-effects overwritten [-Werror]
drivers/net/vrf.c:964:3: error: (near initialization for ‘fl6’) [-Werror]
I have no idea what this warning is even trying to say, but it does
seem like a false positive. Reordering the initialization in to match
the structure definition gets rid of the warning, and might also avoid
whatever gcc thinks is wrong here.
Fixes: 9ff7438460 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.
Semantic patch used to resolve this issue:
@@
expression e,e2; constant c;
statement S;
@@
e = kzalloc(e2, c);
if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Sudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tnapi is being initialized and then immediately updated and
hence the initialiation is redundant. Clean up the warning
by moving the declaration and initialization to the inside
of the for-loop.
Cleans up clang scan-build warning:
warning: Value stored to 'tnapi' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The control process (NSP) may take some time to complete its
initialization. This is not a problem on most servers, but
on very fast-booting machines it may not be ready for operation
when driver probes the device. There is also a version of the
flash in the wild where NSP tries to train the links as part
of init. To wait for NSP initialization we should make sure
its resource has already been added to the resource table.
NSP adds itself there as last step of init.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Board state informs us which low-level initialization stages the card
has completed. We should wait for the card to be fully initialized
before trying to communicate with it, not only before we configure
passing traffic.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we did not check the flow dissector against a list of allowed
and supported flow key dissectors. This patch introduces such a list and
correctly rejects unsupported flow keys.
Fixes: 43f84b72c5 ("nfp: add metadata to each flow offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 TSO requests with extension hdrs are a problem to the
Lancer and BEx chips. Workaround is to disable TSO6 feature
for such packets.
Also in Lancer chips, MSS less than 256 was resulting in TX stall.
Fix this by disabling GSO when MSS less than 256.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A randconfig build caused a compile failure:
drivers/net/ethernet/nuvoton/w90p910_ether.c: In function 'w90p910_ether_close':
drivers/net/ethernet/nuvoton/w90p910_ether.c:580:2: error: implicit declaration of function 'free_irq'; did you mean 'free_uid'? [-Werror=implicit-function-declaration]
Adding the correct include fixes the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8b426dc54c ("bonding: remove hardcoded value") changed the
default value for tlb_dynamic_lb which lead to either broken ALB mode
(since tlb_dynamic_lb can be changed only in TLB) or setting TLB mode
with tlb_dynamic_lb equal to 0.
The first issue was recently fixed by setting tlb_dynamic_lb to 1 always
when switching to ALB mode, but the default value is still wrong and
we'll enter TLB mode with tlb_dynamic_lb equal to 0 if the mode is
changed via netlink or sysfs. In order to restore the previous behaviour
and default value simply remove the mode check around the default param
initialization for tlb_dynamic_lb which will always set it to 1 as
before.
Fixes: 8b426dc54c ("bonding: remove hardcoded value")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the offloading of mirred actions under
matchall classifiers, mlxsw would find the destination port
associated with the offloaded action and utilize it for undoing
the configuration.
Depending on the order by which ports are removed, it's possible that
the destination port would get removed before the source port.
In such a scenario, when actions would be flushed for the source port
mlxsw would perform an illegal dereference as the destination port is
no longer listed.
Since the only item necessary for undoing the configuration on the
destination side is the port-id and that in turn is already maintained
by mlxsw on the source-port, simply stop trying to access the
destination port and use the port-id directly instead.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure pause time to 0xffff when tx flow control enabled
Set pause time to 0xffff in the pause frame to indicate the
partner to stop sending the packets. When RX buffer frees up,
the device sends pause frame with pause time zero for partner to
resume transmission.
Fixes: 2f7ca802bd ("Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and
patches
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlm38VMLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYNa+BAAjlTbZ2DhEmBDKHDYjQepnqdw7oY/5B/6A3GKArbR
psXDmWR8HetbJC1+Yg2aaCvSWdza9cR36juI4WSsA2+4FVLU0nj5elkX9QEN/eP4
kiUuwUXCKi3MNd55ESIiVQos0RKvQ8us7rLDfug2h/8dVP5EdLNI//axHY4Y/R7k
6j6ymal9QdHxLj8wdkAQ332womV2jQH44ISIy/Eu/eF1DmWJ1HZvgO/PNeSyVpwB
bP8CRfMAnQDFqB0XiwCXyukNKntvBe7ZpazMdQKH6bObiLOa8DT2Ex/UeG6VBtb3
TXeLW9aSJDG9FfzlqwDlySZWqQlvcEEK7DWm7kNka9tiHx+AKZW+utlrS7Pvofut
ufqD9NRrmutBzgXsZiri/x9b5+UsREKsdHNyLHVfjYo9PlEsZwMjaXxExAlEdgvl
L0pU4EpLP8kK5pRV5K8IXCEVMyoejI2ZIrtu5DHlc3mblUApXkKx1TG81gJsncHh
fDLARilSgCN6g8wQjSiBiXwS6ynBRcmvpeIxrh3x7xQ7OqmqDMS5JcgJCNvBQEKm
yEMCKd8vf30Jpva3VRmQXyUiDMwebguUqSJUDJW0JeDFFGQ7O39JeOwB72LzVHjZ
N9VMh3gCvtkF2ZPV+HIPNbTFnfydzyjNW/BpGt4r5cyvfd2TjEDSPFeIOWZ+chVQ
j68=
=qHNs
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
Commit cbf5ecb305 ("net: bonding: Fix transmit load balancing in
balance-alb mode") tried to fix transmit dynamic load balancing in
balance-alb mode, which wasn't working after commit 8b426dc54c
("bonding: remove hardcoded value").
It turned out that my previous patch only fixed the case when
balance-alb was specified as bonding module parameter, and not when
balance-alb mode was set using /sys/class/net/*/bonding/mode (the most
common usage). In the latter case, tlb_dynamic_lb was set up according
to the default mode of the bonding interface, which happens to be
balance-rr.
This additional patch addresses this issue by setting up tlb_dynamic_lb
to 1 if "mode" is set to balance-alb through the sysfs interface.
I didn't add code to change tlb_balance_lb back to the default value for
other modes, because "mode" is usually set up only once during
initialization, and it's not worthwhile to change the static variable
bonding_defaults in bond_main.c to a global variable just for this
purpose.
Commit 8b426dc54c also changes the value of tlb_dynamic_lb for
balance-tlb mode if it is set up using the sysfs interface. I didn't
change that behavior, because the value of tlb_balance_lb can be changed
using the sysfs interface for balance-tlb, and I didn't like changing
the default value back and forth for balance-tlb.
As for balance-alb, /sys/class/net/*/bonding/tlb_balance_lb cannot be
written to. However, I think balance-alb with tlb_dynamic_lb set to 0
is not an intended usage, so there is little use making it writable at
this moment.
Fixes: 8b426dc54c ("bonding: remove hardcoded value")
Reported-by: Reinis Rozitis <r@roze.lv>
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Cc: stable@vger.kernel.org # v4.12+
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only need to wakeup the initiator after all sub-channels
are opened.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a virtual device is added dynamically (via host console), then
the vmbus sends an offer message for the primary channel. The processing
of this message for networking causes the network device to then
initialize the sub channels.
The problem is that setting up the sub channels needs to wait until
the subsequent subchannel offers have been processed. These offers
come in on the same ring buffer and work queue as where the primary
offer is being processed; leading to a deadlock.
This did not happen in older kernels, because the sub channel waiting
logic was broken (it wasn't really waiting).
The solution is to do the sub channel setup in its own work queue
context that is scheduled by the primary channel setup; and then
happens later.
Fixes: 732e49850c ("netvsc: fix race on sub channel creation")
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not handle correctly the access to the upper page
in case of SFP/SFP+ EEPROM. In that case the offset should be local
and the I2C address should be changed.
Fixes: 2ea109039c ("mlxsw: spectrum: Add support for access cable info via ethtool")
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here so we accidentally free "skb" instead of "skbn".
It leads to a double free and a leak. After discussing with Subash,
it's better to just move the check before the allocation and avoid the
need to free.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"The iwlwifi firmware compat fix is in here as well as some other
stuff:
1) Fix request socket leak introduced by BPF deadlock fix, from Eric
Dumazet.
2) Fix VLAN handling with TXQs in mac80211, from Johannes Berg.
3) Missing __qdisc_drop conversions in prio and qfq schedulers, from
Gao Feng.
4) Use after free in netlink nlk groups handling, from Xin Long.
5) Handle MTU update properly in ipv6 gre tunnels, from Xin Long.
6) Fix leak of ipv6 fib tables on netns teardown, from Sabrina Dubroca
with follow-on fix from Eric Dumazet.
7) Need RCU and preemption disabled during generic XDP data patch,
from John Fastabend"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
bpf: make error reporting in bpf_warn_invalid_xdp_action more clear
Revert "mdio_bus: Remove unneeded gpiod NULL check"
bpf: devmap, use cond_resched instead of cpu_relax
bpf: add support for sockmap detach programs
net: rcu lock and preempt disable missing around generic xdp
bpf: don't select potentially stale ri->map from buggy xdp progs
net: tulip: Constify tulip_tbl
net: ethernet: ti: netcp_core: no need in netif_napi_del
davicom: Display proper debug level up to 6
net: phy: sfp: rename dt properties to match the binding
dt-binding: net: sfp binding documentation
dt-bindings: add SFF vendor prefix
dt-bindings: net: don't confuse with generic PHY property
ip6_tunnel: fix setting hop_limit value for ipv6 tunnel
ip_tunnel: fix setting ttl and tos value in collect_md mode
ipv6: fix typo in fib6_net_exit()
tcp: fix a request socket leak
sctp: fix missing wake ups in some situations
netfilter: xt_hashlimit: fix build error caused by 64bit division
netfilter: xt_hashlimit: alloc hashtable with right size
...
This reverts commit 95b80bf3db ("mdio_bus:
Remove unneeded gpiod NULL check"), this commit assumed that GPIOLIB
checks for NULL descriptors, so it's safe to drop them, but it is not
when CONFIG_GPIOLIB is disabled in the kernel. If we do call
gpiod_set_value_cansleep() on a GPIO descriptor we will issue warnings
coming from the inline stubs declared in include/linux/gpio/consumer.h.
Fixes: 95b80bf3db ("mdio_bus: Remove unneeded gpiod NULL check")
Reported-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't remove rx_napi specifically just before free_netdev(),
it's supposed to be done in it and is confusing w/o tx_napi deletion.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will make it explicit some messages are of the form:
dm9000_dbg(db, 5, ...
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Rx rate select control gpio property name match the documented
binding. This would make the addition of 'rate-select1-gpios' for SFP+
support more natural.
Also, make the MOD-DEF0 gpio property name match the documentation.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few fixes to regressions introduced in the last one or two releases.
The iwlwifi fix is for a regression reported by Linus.
rtlwifi
* fix two antenna selection related bugs
iwlwifi
* fix regression with older firmwares
brcmfmac
* workaround firmware crash for bcm4345
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZsrqPAAoJEG4XJFUm622bT04IAIR/MiSKo+IJ8wpvzXJ5K7x5
/IzGDoJofqiQHVG0Rc72+0ooFwSe6nxQ3E+OzQM9yLIC8XcjPwd8mqnV4dzF5rIs
Q0ou092eBOVfMZO9EMrZJLuFiItfF8deH+nnYDuQBFsTHVKdkYVltB5JUX98hj6q
SFY7RYgmTcXq7j5H5u7AuDueJu0maHq2eb9t6MvtD06pbyvmh5t6CRsSORinMfff
090mWhPYTgZZqCuVQk9lki2671vgqjqfyr2M0hGWnsQCM+IiXUIptSGPEjwRDGDv
0yePGq750YPVjlMixIHfKEfm446YHp++Yjl/QzYCV3bbCHF5yEAUVoG8Nv3ibxc=
=DL06
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Few fixes to regressions introduced in the last one or two releases.
The iwlwifi fix is for a regression reported by Linus.
rtlwifi
* fix two antenna selection related bugs
iwlwifi
* fix regression with older firmwares
brcmfmac
* workaround firmware crash for bcm4345
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware feature check introduced for multi-scheduled scan is also
failing for bcm4345 devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The condition to check if reorder buffer ran out of
space is faulty, as it takes into account only the
NSSN.
In case the head SN was too far behind the reorder
buffer should move forward, regardless of the NSSN
status.
This caused the driver to release packets out of order
in some scenarios.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always must set the status to what we consider success before
calling iwl_mvm_send_cmd_status() (also iwl_mvm_send_cmd_pdu_status()
which calls it). Fix a few places where initialization is missing.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always need to initialize the status argument to the success case
before calling iwl_mvm_send_cmd_status() or
iwl_mvm_send_cmd_pdu_status() (which calls the former) otherwise we
may get an uninitialized value back. In this case, we use
ADD_STA_SUCCESS as success.
Fixes: 732d06e9d9 ("iwlwifi: mvm: add station before allocating a queue")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were ignoring the FIF_ALLMULTI flag when setting the multicast
addresses with MCAST_FILTER_CMD. Check if this flag is set and enable
pass_all accordingly. We also need to set the count to 0 if pass_all
is enable so we don't pass addresses to the firmware when not needed
(as doing so causes an assert).
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196741
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MCAST_FILTER_CMD can get quite large when we have many mcast
addresses to set (we support up to 255). So the command should be
send as NOCOPY to prevent a warning caused by too-long commands:
WARNING: CPU: 0 PID: 9700 at /root/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/pcie/tx.c:1550 iwl_pcie_enqueue_hcmd+0x8c7/0xb40 [iwlwifi]
Command MCAST_FILTER_CMD (0x1d0) is too large (328 bytes)
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196743
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_start_mac_queues() takes a bitmap of the queues to wake.
When deferred tx is purged, set the bit of the hw_queue so
the correct queue will be waken up.
Fixes: 7e39a00d59 ("iwlwifi: mvm: start mac queues when deferred tx frames are purged")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new state to enum iwl_mvm_agg_state, which is used between
queueing the work that starts tx aggregations and actually starting that
work (changing to state IWL_AGG_STARTING).
This solves a race where ieee80211_start_tx_ba_session is called a
second time, before the work queued by the first run has a chance to
change the agg_state. In this case the second call to
ieee80211_start_tx_ba_session returns an error, and the fallback is to
abort the ba session start.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AP interfaces now send all non-bufferable frames using the broadcast
station. Thus allow them to use the probe queue and don't warn about
it.
Fixes: eb045e6e03 ("iwlwifi: mvm: Avoid deferring non bufferable frames")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting wowlan mac80211 requests flush w/o vif
and we ignore this request. As a result some packets
stay stuck in the queue and it may end up with a queue
hang.
Allow the driver to flush queues even if station isn't
specified.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we set disconnect on wowlan and run suspend/resume, will run
into:
...snipped
iwlwifi 0000:01:00.0: Failed to load firmware chunk!
iwlwifi 0000:01:00.0: Could not load the [0] uCode section
iwlwifi 0000:01:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
It is because we still keep IWL_MVM_STATUS_IN_HW_RESTART in
__iwl_mvm_resume. When mac80211 starts the device as
__iwl_mvm_mac_start(), we will miss iwl_mvm_restart_cleanup(mvm).
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
that are entirely function pointers (along with a couple designated
initializer fixes).
- For the structleak plugin, provide an option to perform zeroing
initialization of all otherwise uninitialized stack variables that are
passed by reference (Ard Biesheuvel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=3jxS
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This finishes the porting work on randstruct, and introduces a new
option to structleak, both noted below:
- For the randstruct plugin, enable automatic randomization of
structures that are entirely function pointers (along with a couple
designated initializer fixes).
- For the structleak plugin, provide an option to perform zeroing
initialization of all otherwise uninitialized stack variables that
are passed by reference (Ard Biesheuvel)"
* tag 'gcc-plugins-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: structleak: add option to init all vars used as byref args
randstruct: Enable function pointer struct detection
drivers/net/wan/z85230.c: Use designated initializers
drm/amd/powerplay: rv: Use designated initializers
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
-----BEGIN PGP SIGNATURE-----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=QYS4
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-09-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Back from a long absence, so we have a number of things:
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The LEDS_CMD command is only supported in some newer FW versions
(e.g. iwlwifi-8000C-31.ucode), so we can't send it to older versions
(such as iwlwifi-8000C-27.ucode).
To fix this, check for a new bit in the FW capabilities TLV that tells
when the command is supported.
Note that the current version of -31.ucode in linux-firmware.git
(31.532993.0) does not have this capability bit set, so the LED won't
work, even though this version should support it. But we will update
this firmware soon, so it won't be a problem anymore.
Fixes: 7089ae634c ("iwlwifi: mvm: use firmware LED command where applicable")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex"),
the code turns on a call to exhalbtc_bind_bt_coex_withadapter(). This
routine contains a bug that causes incorrect antenna selection for those
HP laptops with only one antenna and an incorrectly programmed EFUSE.
These boxes are the ones that need the ant_sel module parameter.
Fixes: 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.13+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when
hw initialisation done"), there is an additional error when the module
parameter ant_sel is used to select the auxilary antenna. The error is
that the antenna selection is not checked when writing the antenna
selection register.
Fixes: bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.12+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-09-05
This series contains fixes for i40e only.
These two patches fix an issue where our nvmupdate tool does not work on RHEL 7.4
and newer kernels, in fact, the use of the nvmupdate tool on newer kernels can
cause the cards to be non-functional unless these patches are applied.
Anjali reworks the locking around accessing the NVM so that NVM acquire timeouts
do not occur which was causing the failed firmware updates.
Jake correctly updates the wb_desc when reading the NVM through the AdminQ.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.
Fixes: 7073f46e44 ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit
96a39aed25 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed25 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 183db4 ("drivers: net: xgene: Correct probe sequence handling")
changed the return type of xgene_enet_check_phy_handle() to void.
This patch, removes the return statement from the last line.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes configuring tx/rx delay values for ACPI.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes reading tx/rx delay values for ACPI.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function calls to kcalloc use wrong parameter order and incorrect flags
values. GFP_KERNEL is used instead of flags now and the order is corrected.
The change was done using the following coccinelle script:
@@
expression E1,E2;
type T;
@@
-kcalloc(E1, E2, sizeof(T))
+kcalloc(E2, sizeof(T), GFP_KERNEL)
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_init() use the parameter dev for two distinct thing:
1) Have a device for all devm_ functions
2) Get device_node from it
Since it is two distinct purpose, this patch add a parameter mdio_mux
that is linked to task 2.
This will also permit to register an of_node mdio-mux that lacks a direct
owning device.
For example a mdio-mux which is a subnode of a real device.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is no longer used, the logging function was changed by commit
fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().
Fixes: fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
