Currently intel_dp_check_link_status() tries to retrain the link if
Clock recovery or Channel EQ for any of the lanes indicated by
intel_dp->lane_count is not set. However these values cached in intel_dp
structure can be stale if link training has failed for these values
during previous modeset. Or these values can get stale since we have
now re read the DPCD registers or it can be 0 in case of connected boot
case.
This patch validates these values against the max link rate and max lane
count values.
This is absolutely required incase the common_rates or max lane count
are now different due to link fallback.
v2:
* Include the FIXME commnet inside the function (Ville Syrjala)
* Remove the redundant parenthesis (Ville Syrjala)
v3 by Jani:
* rebase on the DP refactoring series
* rename intel_dp_link_params_is_valid to intel_dp_link_params_valid
* minor stylistic changes
v4:
* Compare the link rate against max link rate not the
common_rates since common_rates does not account for the
lowered fallback link rate value. (Ville Syrjala)
v5:
* Fixed a warning for unused variable (Manasi)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491512412-30016-1-git-send-email-manasi.d.navare@intel.com
Those properties are not hooked up on MST and were ignored. Best not expose them at all.
Without this the next patch fails to start on X.org, because the DP-MST properties could
not be read.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/751b85a0-81cd-09e2-9e60-6d4ddbf1c6ac@linux.intel.com
Testcase: kms_properties
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten needs both the new connector->atomic_check hook and the
connection_mutex locking changes in the probe helpers to be able to
start merging the connector property conversion to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The source might not support as many lanes as the sink, or the link
training might have failed at higher lane counts. Take these into
account.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/cf59530acafaf9258fb643d321ad251b44f34e29.1491485983.git.jani.nikula@intel.com
These are the theoretical maximums common for source and sink. These are
the maximums we should start with. They may be degraded in case of link
training failures, and the dynamic link values are stored separately.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/5088aca253c47dfa18251e1adb976aca1718f083.1491485983.git.jani.nikula@intel.com
If we modify these on the fly depending on the link conditions, don't
pretend they are sink properties.
Some link vs. sink confusion still remains, but we'll take care of them
in follow-up patches.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/3739b4fac502ebd1c6e075a62c1a195e4094eb16.1491485983.git.jani.nikula@intel.com
In link training fallback, we're trying to find a rate that we know is
in a sorted array of common link rates. We don't need to limit the array
using the max rate. For test request, the DP CTS doesn't say we should
limit the rate based on earlier fallback. This lets us get rid of
intel_dp_link_rate_index() and use intel_dp_rate_index() instead.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/33cab481a3228f31e938b5891a6285d892dcf272.1491485983.git.jani.nikula@intel.com
Now that source rates are static and sink rates are updated whenever
DPCD is updated, we can do and cache the intersection of them whenever
sink rates are updated. This reduces code complexity, as we don't have
to keep calling the functions to intersect. We also get rid of several
common rates arrays on stack.
Limiting the common rates by a max link rate can be done by picking the
first N elements of the cached common rates.
v2: get rid of the local common_rates variable (Manasi)
v3: don't clobber cached eDP rates on short pulse (Ville)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/e3b287e8cb6559b1f8fd4e80b78a8d22f1802eb7.1491485983.git.jani.nikula@intel.com
Looking at DPCD DP_MAX_LINK_RATE may be completely bogus for eDP 1.4
which is allowed to use link rate select method and have 0 in max link
rate. With this change, it makes sense to store the max rate as the
actual rate rather than as a bw code.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/3e8baadb406d59f414cab36fed9f0b35d207fde5.1491485983.git.jani.nikula@intel.com
mode_valid() called from drm_helper_probe_single_connector_modes()
may need to look at connector->state because what a valid mode is may
depend on connector properties being set. For example some HDMI modes
might be rejected when a connector property forces the connector
into DVI mode.
Some implementations of detect() already lock all state,
so we have to pass an acquire_ctx to them to prevent a deadlock.
This means changing the function signature of detect() slightly,
and passing the acquire_ctx for locking multiple crtc's.
For the callbacks, it will always be non-zero. To allow callers
not to worry about this, drm_helper_probe_detect_ctx is added
which might handle -EDEADLK for you.
Changes since v1:
- Always set ctx parameter.
Changes since v2:
- Always take connection_mutex when probing.
Changes since v3:
- Remove the ctx from intel_dp_long_pulse, and add
WARN_ON(!connection_mutex) (danvet)
- Update docs to clarify the locking situation. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491504920-4017-1-git-send-email-maarten.lankhorst@linux.intel.com
There is some conflation related to sink rates, making this change more
complicated than it would otherwise have to be. There are three changes
here that are rather difficult to split up:
1) Use the intel_dp->sink_rates array for all DP, not just eDP 1.4. We
initialize it from DPCD on eDP 1.4 like before, but generate it based
on DP_MAX_LINK_RATE on others. This reduces code complexity when we
need to use the sink rates; they are all always in the sink_rates
array.
2) Update the sink rate array whenever we read DPCD, and use the
information from there. This increases code readability when we need
the sink rates.
3) Disentangle fallback rate limiting from sink rates. In the code, the
max rate is a dynamic property of the *link*, not of the *sink*. Do
the limiting after intersecting the source and sink rates, which are
static properties of the devices.
This paves the way for follow-up refactoring that I've refrained from
doing here to keep this change as simple as it possibly can.
v2: introduce use_rate_select and handle non-confirming eDP (Ville)
v3: don't clobber cached eDP rates on short pulse (Ville)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/071bad76467f8ab2e73f3f61ad52d5a468004c71.1490712890.git.jani.nikula@intel.com
We need the source rates array so often that it makes sense to set it
once at init. This reduces function calls when we need the rates, making
the code easier to follow.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/aa998882d2b824f671272c60e9d26621ab9d2d17.1490712890.git.jani.nikula@intel.com
Rename the function, move it at the top, and reuse in
intel_dp_link_rate_index(). If there was a reason in the past to use
reverse search order here, there isn't now.
The names may be slightly confusing now, but intel_dp_link_rate_index()
will go away in follow-up patches.
v2: Use name intel_dp_rate_index (Dhinakaran)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/c7b6197aaa12e368a0d024dc142fa574fd0443a7.1490712890.git.jani.nikula@intel.com
We shouldn't silently use the first element if we can't find the rate
we're looking for. Make rate_to_index() more generally useful, and
fallback to the first element in the caller, with a big warning.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8a6e83b7bf35da0cbbc703ae157944107ff145be.1490712890.git.jani.nikula@intel.com
I can't think of a real world bug this could cause now, but this will be
required in follow-up work. While at it, change the parameter order to
be slightly more sensible.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/ff5b08f45a72c2247f5326b080027e2f5d8cc4ee.1490712890.git.jani.nikula@intel.com
At least a ParadTech PS175 LSPCON chip/firmware uses long instead of
short pulses to signal output unplug/plug events. This is contrary to
how branch devices normally work which use short HPD signaling. This
chip will also switch to LS mode after an unplug event, which could be
the consequence of the long HPD signaling semantics and an effort to
save power automatically. Because of this we'll fail to do AUX and
detect the output after a replug event.
To fix this make sure we are in PCON mode during connector detection.
v2:
- Switch the mode in the proper spot.
Cc: raptorteak@gmail.com
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98912
Reported-and-tested-by: raptorteak@gmail.com
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487776252-6288-1-git-send-email-imre.deak@intel.com
Rather than sprinkling ideas of how big the DDI buf translation tables
are somewhere in intel_dp.c, let's concentrate it all in intel_ddi.c
where the actual tables are defined. To that end we introduce
intel_ddi_dp_voltage_max() which will actually look at the proper
translation table to determine what is the maximum voltage swing level
supported.
v2: Mask out the preemphasis bits from the return value of
intel_ddi_dp_voltage_max()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223174901.26749-1-ville.syrjala@linux.intel.com
This reverts commit 7ee686034b "drm/i915/dp: Ratelimit DP aux timeout
messages" as although it successfully squelches the debug messages, when
it does so it generates a warning instead. CI lights up orange with all
the warnings!
In its current incarnation DRM_DEBUG_RATELIMITED is not usable for us,
and we need to first teach lib/ratelimit.c not to warn when used for
debug messages.
Fixes: 7ee686034b ("drm/i915/dp: Ratelimit DP aux timeout messages")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lyude <lyude@redhat.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/20170223115102.7059-1-chris@chris-wilson.co.uk
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Right now this is just leaving a lot of spam in dmesg that makes real
issues more difficult to debug. As well (as noted by the comment right
above the DRM_DEBUG_KMS() call) this is normal behavior when there's
nothing connected to the DisplayPort connector.
Signed-off-by: Lyude <lyude@redhat.com>
The max link parameters should be set/reset only on HPD or
connected boot case or on system resume.
Add a flag reset_link_params to intel_dp to decide when
to reset the max link parameters. This prevents the parameters
from getting reset/overwritten through all other
connector->funcs->detect() calls. This is important when link
training fails and the max link params are modified to the
lower fallback values.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486515251-23469-1-git-send-email-manasi.d.navare@intel.com
Until recently vlv_steal_power_sequencer() wasn't being called for
normal DP ports, and hence it could assert that it should only be
called for pipe A and B (since pipe C doesn't support eDP). However
that changed when we started to consider normal DP ports as well when
choosing a PPS. So we will now get spurious warnings when
vlv_steal_power_sequencer() does get called for pipe C. Avoid this by
moving the WARN down into vlv_detach_power_sequencer() where this
assertion should still hold.
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Fixes: 9f2bdb006a ("drm/i915: Prevent PPS stealing from a normal DP port on VLV/CHV")
References: https://bugs.freedesktop.org/show_bug.cgi?id=95287
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170208175254.10958-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
This shaves a few lines from intel_dp_init_connector() and will serve as
a good place to add other port specific information in a follow up
patch.
While at it, convert BUG() to MISSING_CASE() in the default case.
v2: s/BUG/MISSING_CASE. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170203140316.20792-2-ander.conselvan.de.oliveira@intel.com
The current dev_cdclk vs. cdclk vs. atomic_cdclk_freq is quite a mess.
So here I'm introducing the "actual" and "logical" naming for our
cdclk state. "actual" is what we'll bash into the hardware and "logical"
is what everyone should use for state computaion/checking and whatnot.
We'll track both using the intel_cdclk_state as both will need other
differing parameters than just the actual cdclk frequency.
While doing that we can at the same time unify the appearance of the
.modeset_calc_cdclk() implementations a little bit.
v2: Commit dev_priv->cdclk.actual since that already has the
new state by the time .modeset_commit_cdclk() is called.
v3: s/locical/logical/ and improve the docs a bit
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170120182205.8141-9-ville.syrjala@linux.intel.com
Introduce intel_cdclk state which for now will track the cdclk
frequency, the vco frequency and the reference frequency (not sure we
want the last one, but I put it there anyway). We'll also make the
.get_cdclk() function fill out this state structure rather than
just returning the current cdclk frequency.
One immediate benefit is that calling .get_cdclk() will no longer
clobber state stored under dev_priv unless ex[plicitly told to do
so. Previously it clobbered the vco and reference clocks stored
there on some platforms.
We'll expand the use of this structure to actually precomputing the
state and whatnot later.
v2: Constify intel_cdclk_state_compare()
v3: Document intel_cdclk_state_compare()
v4: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183345.19763-1-ville.syrjala@linux.intel.com
During system resume time initialization the HPD level on LSPCON ports
can stay low for an extended amount of time, leading to failed AUX
transfers and LSPCON initialization. Fix this by waiting for HPD to get
asserted.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99178
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-3-git-send-email-imre.deak@intel.com
Chris Wilson wants the new fence tracepoint added in
commit 8c96c67801
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jan 24 11:57:58 2017 +0000
dma/fence: Export enable-signaling tracepoint for emission by drivers
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
Make the code selecting the RGB quantization range a little less magicy
by wrapping it up in a small helper.
v2: s/adjusted_mode/mode in vc4 to make it actually compile
v3: Add a comment proposed by Eric
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111141835.25369-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
The intel_dp_autotest_video_pattern() function gets invoked through the
compliance test handler on a HPD short pulse if the test type is
set to DP_TEST_VIDEO_PATTERN. This performs the DPCD registers
reads to read the requested test pattern, video pattern resolution,
frame rate and bits per color value. The results of this analysis
are handed off to userspace so that the userspace app can set the
video pattern mode appropriately for the test result/response.
When the test is requested with specific BPC value, we read the BPC
value from the DPCD register. If this BPC value in intel_dp structure
has a non-zero value and we're on a display port connector, then we use
the value to calculate the bpp for the pipe. Also in this case if its
a 18bpp video pattern request, then we force the dithering on pipe to be
disabled since it causes CRC mismatches.
The compliance_test_active flag is set at the end of the individual
test handling functions. This is so that the kernel-side operations
can be completed without the risk of interruption from the userspace
app that is polling on that flag.
v5:
* Remove test_result variable
* Populate the compliance test data at the end of the function (Jani Nikula)
v4:
*Return TEST_NAK on read failures and invalid values (Jani Nikula)
* Address CRC mismatch errors
v3:
* Use the updated properly shifted bit definitions (Jani Nikula)
* Force dithering to be disabled on 18bpp compliance
test request (Manasi Navare)
v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274909-17470-1-git-send-email-manasi.d.navare@intel.com
This patch addresses a few issues from the original patch for
DP Compliance EDID test support submitted by
Todd Previte<todd.previte@gmail.com>
Video Mode requested in the EDID test handler for the EDID Read
test (CTS 4.2.2.3) should be set to PREFERRED as per the CTS spec.
v2:
* Added read debugfs data from test_data.edid if its EDID test (Jani NIkula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484968170-12467-3-git-send-email-manasi.d.navare@intel.com
This patch adds support to handle automated DP compliance
link training test requests. This patch has been tested with
Unigraf DPR-120 DP Compliance device for testing Link
Training Compliance.
After we get a short pulse Compliance test request, test
request values are read and hotplug uevent is sent in order
to trigger another modeset during which the pipe is configured
and link is retrained and enabled for link parameters requested
by the test.
v5:
* Only modify the compliance structure after all validation
is done (Jani Nikula)
* Remove the variable test_result (Jani Nikula)
v4:
* Return TEST_NAK for read failures and invalid
values (Jani Nikula)
* Conver the test link BW to link rate before storing (Jani Nikula)
v3:
* Validate the test link rate and lane count as soon as
the request comes (Jani Nikula)
v2:
* Validate the test lane count before using it in
intel_dp_compute_config (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274594-17361-1-git-send-email-manasi.d.navare@intel.com
Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.
So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).
The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.
v2: fix conflict with IS_LP and 3 new cases for this
big core bucket:
- intel_ddi.c: intel_ddi_get_link_dpll
- intel_fbc.c: find_compression_threshold
- i915_gem_gtt.c: gtt_write_workarounds
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com
There is no point in setting intel_dp->compliance.test_type, and
proceeding with the autotests, if we're about to NAK the request. Some
drive-by cleanups while at it.
v2: look at the ACK bit, as the result may also contain
TEST_EDID_CHECKSUM_WRITE
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484931846-25390-1-git-send-email-jani.nikula@intel.com
As per edp1.4 spec , alpm is required for psr2 operation as it's
used for all psr2 main link power down management and alpm enable
bit must be set for psr2 operation.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: vathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483356663-32668-6-git-send-email-vathsala.nagaraju@intel.com
Commit cc3f90f063 ("drm/i915/glk: Reuse broxton code for geminilake")
missed a few of occurences of IS_BROXTON() that should have been
coverted to IS_GEN9_LP().
v2: Cite the right commit. (Ander)
Fixes: cc3f90f063 ("drm/i915/glk: Reuse broxton code for geminilake")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com> (v1)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483973495-15138-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Apparently some VLV BIOSen like to leave the VDD force bit enabled
even for power seqeuncers that aren't properly hooked up to any
port. That will result in a imbalance in the AUX power domain
refcount when we stat to use said power sequencer as edp_panel_vdd_on()
will not grab the power domain reference if it sees that the VDD is
already on.
To fix this let's make sure we turn off the VDD force bit when we
initialize the power sequencer registers. That is, unless it's
being done from the init path since there we are actually
initializing the registers for the current power sequencer and
we don't want to turn VDD off needlessly as that would require
waiting for the power cycle delay before we turn it back on.
This fixes the following kind of warnings:
WARNING: CPU: 0 PID: 123 at ../drivers/gpu/drm/i915/intel_runtime_pm.c:1455 intel_display_power_put+0x13a/0x170 [i915]()
WARN_ON(!power_domains->domain_use_count[domain])
...
v2: Fix typos in comment (David)
Cc: stable@vger.kernel.org
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98695
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161220165117.24801-1-ville.syrjala@linux.intel.com
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
There is at least one APL based system using port A in DP mode
(connecting to an on-board DP->VGA adaptor). Atm we'll configure port A
unconditionally as eDP which is incorrect in this case. Fix this by
relying on the VBT DDI port 'internal port' flag instead on all ports on
DDI platforms. For now chicken out from using VBT for port A before
GEN9.
v2:
- Move the DDI port info lookup to intel_bios_is_port_edp() (David, Jani)
- Use the DDI port info on all DDI platforms starting from port B.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482315444-24750-1-git-send-email-imre.deak@intel.com
VLV apparently gets upset if the PPS for a pipe currently driving an
external DP port gets used for VDD stuff on another eDP port. The DP
port falls over and fails to retrain when this happens, leaving the
user staring at a black screen.
Let's fix it by also tracking which pipe is driving which DP/eDP port.
We'll track this under intel_dp so that we'll share the protection
of the pps_mutex alongside the pps_pipe tracking, since the two
things are intimately related.
I had plans to reduce the protection of pps_mutex to cover only eDP
ports, but with this we can't do that. Well, for for VLV/CHV at least.
For other platforms it should still be possible, which would allow
AUX communication to occur in parallel for multiple DP ports.
v2: Drop stray crap from a comment (Imre)
Grab pps_mutex when clearing active_pipe
Fix a typo in the commit message
v3: Make vlv_active_pipe() static
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481738423-29738-1-git-send-email-ville.syrjala@linux.intel.com
This patch does not change anything functionally, just cleans up
the DP compliance related variables and stores them all together
in a separate struct intel_dp_compliance. There is another struct
intel_dp_compliance_data to store all the test data. This makes it easy to
reset the compliance variables through a memset instead of
individual resetting.
v2:
* Removed functional changes for EDID (Jani Nikula)
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwl.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481329371-16306-1-git-send-email-manasi.d.navare@intel.com
