dwork struct is large (>128 byte) and not needed when conntrack module
is not loaded.
Place it in net_generic data instead. The struct net dwork member is now
obsolete and will be removed in a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to keep this in struct net, place it in the net_generic data.
The sysctl pointer is removed from struct net in a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This moves all nf_tables pernet data from struct net to a net_generic
extension, with the exception of the gencursor.
The latter is used in the data path and also outside of the nf_tables
core. All others are only used from the configuration plane.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows followup patch to remove these members from struct net.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move dst_check() to the garbage collector path. Stale routes trigger the
flow entry teardown state which makes affected flows go back to the
classic forwarding path to re-evaluate flow offloading.
IPv6 requires the dst cookie to work, store it in the flow_tuple,
otherwise dst_check() always fails.
Fixes: e5075c0bad ("netfilter: flowtable: call dst_check() to fall back to classic forwarding")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
modprobe calls from the nf_logger_find_get() API causes deadlock in very
special cases because they occur with the nf_tables transaction mutex held.
In the specific case of nf_log, deadlock is via:
A nf_tables -> transaction mutex -> nft_log -> modprobe -> nf_log_syslog \
-> pernet_ops rwsem -> wait for C
B netlink event -> rtnl_mutex -> nf_tables transaction mutex -> wait for A
C close() -> ip6mr_sk_done -> rtnl_mutex -> wait for B
Earlier patch added NFLOG/xt_LOG module softdeps to avoid the need to load
the backend module during a transaction.
For nft_log we would have to add a softdep for both nfnetlink_log or
nf_log_syslog, since we do not know in advance which of the two backends
are going to be configured.
This defers the modprobe op until after the transaction mutex is released.
Tested-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Remove nf_log_common. Now that all per-af modules have been merged
there is no longer a need to provide a helper module.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Provide bridge log support from nf_log_syslog.
After the merge there is no need to load the "real packet loggers",
all of them now reside in the same module.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add ipv6_dev_find to ipv6_stub to allow lookup of net_devices by IPV6
address in net/ipv4/icmp.c.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 8 of RFC 8335 specifies potential security concerns of
responding to PROBE requests, and states that nodes that support PROBE
functionality MUST be able to enable/disable responses and that
responses MUST be disabled by default
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resilient next-hop groups have been added recently, there are two
types of multipath next-hop groups: the legacy "mpath", and the new
"resilient". Calling the legacy next-hop group type "mpath" is unfortunate,
because that describes the fact that a packet could be forwarded in one of
several paths, which is also true for the resilient next-hop groups.
Therefore, to make the naming clearer, rename various artifacts to reflect
the assumptions made. Therefore as of this patch:
- The flag for multipath groups is nh_grp_entry::is_multipath. This
includes the legacy and resilient groups, as well as any future group
types that behave as multipath groups.
Functions that assume this have "mpath" in the name.
- The flag for legacy multipath groups is nh_grp_entry::hash_threshold.
Functions that assume this have "hthr" in the name.
- The flag for resilient groups is nh_grp_entry::resilient.
Functions that assume this have "res" in the name.
Besides the above, struct nh_grp_entry::mpath was renamed to ::hthr as
well.
UAPI artifacts were obviously left intact.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this lock is to avoid a bottleneck in the query/report
event handler logic.
By previous patches, almost all mld data is protected by RTNL.
So, the query and report event handler, which is data path logic
acquires RTNL too. Therefore if a lot of query and report events
are received, it uses RTNL for a long time.
So it makes the control-plane bottleneck because of using RTNL.
In order to avoid this bottleneck, mc_lock is added.
mc_lock protect only per-interface mld data and per-interface mld
data is used in the query/report event handler logic.
So, no longer rtnl_lock is needed in the query/report event handler logic.
Therefore bottleneck will be disappeared by mc_lock.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When query/report packets are received, mld module processes them.
But they are processed under BH context so it couldn't use sleepable
functions. So, in order to switch context, the two workqueues are
added which processes query and report event.
In the struct inet6_dev, mc_{query | report}_queue are added so it
is per-interface queue.
And mc_{query | report}_work are workqueue structure.
When the query or report event is received, skb is queued to proper
queue and worker function is scheduled immediately.
Workqueues and queues are protected by spinlock, which is
mc_{query | report}_lock, and worker functions are protected by RTNL.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifmcaddr6 has been protected by inet6_dev->lock(rwlock) so that
the critical section is atomic context. In order to switch this context,
changing locking is needed. The ifmcaddr6 actually already protected by
RTNL So if it's converted to use RCU, its control path context can be
switched to sleepable.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_sf_list has been protected by mca_lock(spin_lock) so that the
critical section is atomic context. In order to switch this context,
changing locking is needed. The ip6_sf_list actually already protected
by RTNL So if it's converted to use RCU, its control path context can
be switched to sleepable.
But It doesn't remove mca_lock yet because ifmcaddr6 isn't converted
to RCU yet. So, It's not fully converted to the sleepable context.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sflist has been protected by rwlock so that the critical section
is atomic context.
In order to switch this context, changing locking is needed.
The sflist actually already protected by RTNL So if it's converted
to use RCU, its control path context can be switched to sleepable.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of mc_lock is to protect inet6_dev->mc_tomb.
But mc_tomb is already protected by RTNL and all functions,
which manipulate mc_tomb are called under RTNL.
So, mc_lock is not needed.
Furthermore, it is spinlock so the critical section is atomic.
In order to reduce atomic context, it should be removed.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mcast.c has several timers for delaying works.
Timer's expire handler is working under atomic context so it can't use
sleepable things such as GFP_KERNEL, mutex, etc.
In order to use sleepable APIs, it converts from timers to delayed work.
But there are some critical sections, which is used by both process
and BH context. So that it still uses spin_lock_bh() and rwlock.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many tcp sysctls are either bools or small ints that can fit into u8.
Reducing space taken by sysctls can save few cache line misses
when sending/receiving data while cpu caches are empty,
for example after cpu idle period.
This is hard to measure with typical network performance tests,
but after this patch, struct netns_ipv4 has shrunk
by three cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For these sysctls, their dedicated helpers have
to use proc_dou8vec_minmax().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl uses ip_fwd_update_priority() helper,
so the conversion needs to change it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These sysctls that can fit in one byte instead of one int
are converted to save space and thus reduce cache line misses.
- icmp_echo_ignore_all, icmp_echo_ignore_broadcasts,
- icmp_ignore_bogus_error_responses, icmp_errors_use_inbound_ifaddr
- tcp_ecn, tcp_ecn_fallback
- ip_default_ttl, ip_no_pmtu_disc, ip_fwd_use_pmtu
- ip_nonlocal_bind, ip_autobind_reuse
- ip_dynaddr, ip_early_demux, raw_l3mdev_accept
- nexthop_compat_mode, fwmark_reflect
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 098a697b49 ("tcp_metrics: Use a single hash table
for all network namespaces."), tcpm_hash_bucket is local to
net/ipv4/tcp_metrics.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an action to represent the PPPoE hardware offload support that
includes the session ID.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch might have already added the VLAN tag through PVID hardware
offload. Keep this extra VLAN in the flowtable but skip it on egress.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a forward path to reach an ethernet device and hardware
offload is enabled, then use the direct xmit path.
Moreover, store the real device in the direct xmit path info since
software datapath uses dev_hard_header() to push the layer encapsulation
headers while hardware offload refers to the real device.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the vlan id and protocol to the flow tuple to uniquely identify
flows from the receive path. For the transmit path, dev_hard_header() on
the vlan device push the headers. This patch includes support for two
vlan headers (QinQ) from the ingress path.
Add a generic encap field to the flowtable entry which stores the
protocol and the tag id. This allows to reuse these fields in the PPPoE
support coming in a later patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The egress device in the tuple is obtained from route. Use
dev_fill_forward_path() instead to provide the real egress device for
this flow whenever this is available.
The new FLOW_OFFLOAD_XMIT_DIRECT type uses dev_queue_xmit() to transmit
ethernet frames. Cache the source and destination hardware address to
use dev_queue_xmit() to transfer packets.
The FLOW_OFFLOAD_XMIT_DIRECT replaces FLOW_OFFLOAD_XMIT_NEIGH if
dev_fill_forward_path() finds a direct transmit path.
In case of topology updates, if peer is moved to different bridge port,
the connection will time out, reconnect will result in a new entry with
the correct path. Snooping fdb updates would allow for cleaning up stale
flowtable entries.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Obtain the ingress device in the tuple from the route in the reply
direction. Use dev_fill_forward_path() instead to get the real ingress
device for this flow.
Fall back to use the ingress device that the IP forwarding route
provides if:
- dev_fill_forward_path() finds no real ingress device.
- the ingress device that is obtained is not part of the flowtable
devices.
- this route has a xfrm policy.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the xmit_type field that defines the two supported xmit paths in the
flowtable data plane, which are the neighbour and the xfrm xmit paths.
This patch prepares for new flowtable xmit path types to come.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a system with DSA ports, and udhcpcd is configured to bring
interfaces up as soon as they are created.
I create a bridge as follows:
ip link add br0 type bridge
As soon as I create the bridge and udhcpcd brings it up, I also have
avahi which automatically starts sending IPv6 packets to advertise some
local services, and because of that, the br0 bridge joins the following
IPv6 groups due to the code path detailed below:
33:33:ff:6d:c1:9c vid 0
33:33:00:00:00:6a vid 0
33:33:00:00:00:fb vid 0
br_dev_xmit
-> br_multicast_rcv
-> br_ip6_multicast_add_group
-> __br_multicast_add_group
-> br_multicast_host_join
-> br_mdb_notify
This is all fine, but inside br_mdb_notify we have br_mdb_switchdev_host
hooked up, and switchdev will attempt to offload the host joined groups
to an empty list of ports. Of course nobody offloads them.
Then when we add a port to br0:
ip link set swp0 master br0
the bridge doesn't replay the host-joined MDB entries from br_add_if,
and eventually the host joined addresses expire, and a switchdev
notification for deleting it is emitted, but surprise, the original
addition was already completely missed.
The strategy to address this problem is to replay the MDB entries (both
the port ones and the host joined ones) when the new port joins the
bridge, similar to what vxlan_fdb_replay does (in that case, its FDB can
be populated and only then attached to a bridge that you offload).
However there are 2 possibilities: the addresses can be 'pushed' by the
bridge into the port, or the port can 'pull' them from the bridge.
Considering that in the general case, the new port can be really late to
the party, and there may have been many other switchdev ports that
already received the initial notification, we would like to avoid
delivering duplicate events to them, since they might misbehave. And
currently, the bridge calls the entire switchdev notifier chain, whereas
for replaying it should just call the notifier block of the new guy.
But the bridge doesn't know what is the new guy's notifier block, it
just knows where the switchdev notifier chain is. So for simplification,
we make this a driver-initiated pull for now, and the notifier block is
passed as an argument.
To emulate the calling context for mdb objects (deferred and put on the
blocking notifier chain), we must iterate under RCU protection through
the bridge's mdb entries, queue them, and only call them once we're out
of the RCU read-side critical section.
There was some opportunity for reuse between br_mdb_switchdev_host_port,
br_mdb_notify and the newly added br_mdb_queue_one in how the switchdev
mdb object is created, so a helper was created.
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
The "lapb_t1timer_running" function in "lapb_timer.c" is used in only
one place: in the "lapb_kick" function in "lapb_out.c". "lapb_kick" calls
"lapb_t1timer_running" to check if the timer is already pending, and if
it is not, schedule it to run.
However, if the timer has already fired and is running, and is waiting to
get the "lapb->lock" lock, "lapb_t1timer_running" will not detect this,
and "lapb_kick" will then schedule a new timer. The old timer will then
abort when it sees a new timer pending.
I think this is not right. The purpose of "lapb_kick" should be ensuring
that the actual work of the timer function is scheduled to be done.
If the timer function is already running but waiting for the lock,
"lapb_kick" should not abort and reschedule it.
Changes made:
I added a new field "t1timer_running" in "struct lapb_cb" for
"lapb_t1timer_running" to use. "t1timer_running" will accurately reflect
whether the actual work of the timer is pending. If the timer has fired
but is still waiting for the lock, "t1timer_running" will still correctly
reflect whether the actual work is waiting to be done.
The old "t1timer_stop" field, whose only responsibility is to ask a timer
(that is already running but waiting for the lock) to abort, is no longer
needed, because the new "t1timer_running" field can fully take over its
responsibility. Therefore "t1timer_stop" is deleted.
"t1timer_running" is not simply a negation of the old "t1timer_stop".
At the end of the timer function, if it does not reschedule itself,
"t1timer_running" is set to false to indicate that the timer is stopped.
For consistency of the code, I also added "t2timer_running" and deleted
"t2timer_stop".
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains Netfilter updates for net-next:
1) Split flowtable workqueues per events, from Oz Shlomo.
2) fall-through warnings for clang, from Gustavo A. R. Silva
3) Remove unused declaration in conntrack, from YueHaibing.
4) Consolidate skb_try_make_writable() in flowtable datapath,
simplify some of the existing codebase.
5) Call dst_check() to fall back to static classic forwarding path.
6) Update table flags from commit phase.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
call_gro_receive() is used to limit GRO recursion, but it works only
with callback pointers.
There's a combined version of call_gro_receive() + INDIRECT_CALL_2()
in <net/inet_common.h>, but it doesn't check for IPv6 modularity.
Add a similar new helper to cover both of these. It can and will be
used to avoid retpoline overhead when IP header lies behind another
offloaded proto.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
If some source file includes <net/gro.h>, but doesn't include
<linux/indirect_call_wrapper.h>:
In file included from net/8021q/vlan_core.c:7:
./include/net/gro.h:6:1: warning: data definition has no type or storage class
6 | INDIRECT_CALLABLE_DECLARE(struct sk_buff *ipv6_gro_receive(struct list_head *,
| ^~~~~~~~~~~~~~~~~~~~~~~~~
./include/net/gro.h:6:1: error: type defaults to ‘int’ in declaration of ‘INDIRECT_CALLABLE_DECLARE’ [-Werror=implicit-int]
[...]
Include <linux/indirect_call_wrapper.h> directly. It's small and
won't pull lots of dependencies.
Also add some incomplete struct declarations to be fully stacked.
Fixes: 04f00ab227 ("net/core: move gro function declarations to separate header ")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Several patches to testore use of memory barriers instead of RCU to
ensure consistent access to ruleset, from Mark Tomlinson.
2) Fix dump of expectation via ctnetlink, from Florian Westphal.
3) GRE helper works for IPv6, from Ludovic Senecaux.
4) Set error on unsupported flowtable flags.
5) Use delayed instead of deferrable workqueue in the flowtable,
from Yinjun Zhang.
6) Fix spurious EEXIST in case of add-after-delete flowtable in
the same batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for a driver to be able to query a bridge for information
about itself, e.g. reading out port flags, it has to use a netdev that
is known to the bridge. In the simple case, that is just the netdev
representing the port, e.g. swp0 or swp1 in this example:
br0
/ \
swp0 swp1
But in the case of an offloaded lag, this will be the bond or team
interface, e.g. bond0 in this example:
br0
/
bond0
/ \
swp0 swp1
Add a helper that hides some of this complexity from the
drivers. Then, redefine dsa_port_offloads_bridge_port using the helper
to avoid double accounting of the set of possible offloaded uppers.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not update table flags from the preparation phase. Store the flags
update into the transaction, then update the flags from the commit
phase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simplify existing fast NAT routines by returning void. After the
skb_try_make_writable() call consolidation, these routines cannot ever
fail.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This allows to remove the default case which should not ever happen and
that was added to avoid gcc warnings on unhandled FLOW_OFFLOAD_DIR_MAX
enumeration case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
commit e97c3e278e ("tproxy: split off ipv6 defragmentation to a separate
module") left behind this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Honor flowtable flags from the control update path. Disallow disabling
to toggle hardware offload support though.
Fixes: 8bb69f3b29 ("netfilter: nf_tables: add flowtable offload control plane")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support for legacy Broadcom tags, which are similar to DSA_TAG_PROTO_BRCM.
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a non-initial netns is destroyed, the usual policy is to delete
all virtual network interfaces contained, but move physical interfaces
back to the initial netns. This keeps the physical interface visible
on the system.
CAN devices are somewhat special, as they define rtnl_link_ops even
if they are physical devices. If a CAN interface is moved into a
non-initial netns, destroying that netns lets the interface vanish
instead of moving it back to the initial netns. default_device_exit()
skips CAN interfaces due to having rtnl_link_ops set. Reproducer:
ip netns add foo
ip link set can0 netns foo
ip netns delete foo
WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60
CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1
Workqueue: netns cleanup_net
[<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14)
[<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8)
[<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114)
[<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac)
[<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60)
[<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380)
[<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438)
[<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8)
[<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c)
[<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
To properly restore physical CAN devices to the initial netns on owning
netns exit, introduce a flag on rtnl_link_ops that can be set by drivers.
For CAN devices setting this flag, default_device_exit() considers them
non-virtual, applying the usual namespace move.
The issue was introduced in the commit mentioned below, as at that time
CAN devices did not have a dellink() operation.
Fixes: e008b5fc8d ("net: Simplfy default_device_exit and improve batching.")
Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently tcp_check_req can be called with obsolete req socket for which big
socket have been already created (because of CPU race or early demux
assigning req socket to multiple packets in gro batch).
Commit e0f9759f53 ("tcp: try to keep packet if SYN_RCV race
is lost") added retry in case when tcp_check_req is called for PSH|ACK packet.
But if client sends RST+ACK immediatly after connection being
established (it is performing healthcheck, for example) retry does not
occur. In that case tcp_check_req tries to close req socket,
leaving big socket active.
Fixes: e0f9759f53 ("tcp: try to keep packet if SYN_RCV race is lost")
Signed-off-by: Alexander Ovechkin <ovov@yandex-team.ru>
Reported-by: Oleg Senin <olegsenin@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend psample to report the following attributes when available:
* Output traffic class as a 16-bit value
* Output traffic class occupancy in bytes as a 64-bit value
* End-to-end latency of the packet in nanoseconds resolution
* Software timestamp in nanoseconds resolution (always available)
* Packet's protocol. Needed for packet dissection in user space (always
available)
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, callers of psample_sample_packet() pass three metadata
attributes: Ingress port, egress port and truncated size. Subsequent
patches are going to add more attributes (e.g., egress queue occupancy),
which also need an indication whether they are valid or not.
Encapsulate packet metadata in a struct in order to keep the number of
arguments reasonable.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Dissector code never modifies the input buffer, neither skb nor
raw data.
Make 'data' argument const for all of the Flow dissector's functions.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
