Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.
Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.
Note that this replaces the commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dan O'Donovan <dan@emutex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and data circuits
after tuning failure").
A better fix is available, and it will be applied to older stable releases,
so get this out of the way by reverting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:
Device (SDHB) {
Name (_ADR, 0x00110000)
Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SDIO Controller - 80862295")
Name (_UID, 0x02)
Name (_HRV, One)
A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I see no override of read/write callbacks in sdhci-of-at91.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.
The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add PCI ID for Intel byt sdio host controller sub-vended by NI.
The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before calling clk_round_rate(), put the spin_unlock_irq() in
sdhci_s3c_consider_clock() function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.
None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.
Delete the parameter from the callback and all users, as it is
just pointless cruft.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With commit f35bbf61ab ("gpio / ACPI: Return -EPROBE_DEFER if the
gpiochip was not found"), a gpio descriptor request can now be deferred if
the providing gpio host controller driver hasn't been loaded yet. Allow use
in mmc slot probe in order to prevent card detect gpio setup from failing
in this case.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.
The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.
The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.
The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_enable_clk from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.
Without this patch we see below errors on such SDHC controllers
sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
mmc0: tuning execution failed: -110
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "clock-freq-min-max" property was deprecated.
There is "max-frequency" property in drivers/mmc/core/host.c
"max-frequency" can be replaced with "clock-freq-min-max".
Minimum clock value might be set to 100K by default.
Then MMC core should try to find the correct value from 400K to 100K.
So it just needs to set Maximum clock value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
stop_cmdr should be set to values relevant to stop command.
It migth be assigned to values whatever there is mrq->stop or not.
Then it doesn't need to use dw_mci_prepare_command().
It's enough to use the prep_stop_abort for preparing stop command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If DW_MMC_CARD_NO_USE_HOLD isn't set, it's usesd by default.
Enve if SDMMC_CMD_USB_HOLD_REG is set in prepare_command(), but it
doesn't set in pre_stop_abort().
To maintain the consistency, add the checking condition for this.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is no property "clock-freq-min-max", mmc->f_min should be set
to 400K by default. But Some SoC can be used 100K.
When 100K is used, MMC core will try to check from 400K to 100K.
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If display the debug message, this message should be spamming.
If flags is maintained the previous value, didn't display the debug
message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Developer wants to see the real register value, not register offset.
This patch fixed to display the real value of register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trivial fix to spelling mistake "desciptor" to "descriptor" in
dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Request card detect and write protect gpios using the provided API
by mmc core.
If a gpio is provided for card detect, we don't need to poll.
So only use polling when a gpio is not provided.
Once all pdata users register the gpios using gpio descriptors,
we could remove the platform callbacks.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
Card detect and write protect are currently not working on a DT
boot, and the driver relies on polling to get the state
of the card. The current code depends on platform data callbacks
to register and get the state of the gpios.
mmc core provides a generic way to parse device tree configuration,
which will take care of registering the gpios for us, lets use it
so that we don't need to poll, and parse the same properties.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
We surely have SDIO support by now :)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
refactored the sdio irq handler and wrongly used the mask for SD irqs,
not for SDIO irqs. This doesn't really matter in practice because both
values keep the only interrupt we are interested in. But still, this is
wrong and wants to be fixed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wbsd_request_dma() does not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The type of host->private is (unsigned long *). No cast is needed
to return an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add bytewise register accesses support for newer versions of IPROC
SDHCI controllers.
Previous sdhci-iproc versions of SDIO controllers
(such as Raspberry Pi and Cygnus) only allowed for 32-bit register
accesses.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add tuning support for use with SDR104 mode
This includes adding support for the sampling clock controller (SCC).
Based on work by Ai Kyuse.
Cc: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add tuning support for use with SDR104 mode
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An illegal sequence command error may occur if there is a stopbit or
cmd_index error as well as a CRC error. The correct course of action
is to re-enable IRQs
An illegal sequence data error may occur if there is a CRC or stopbit
error, or underrun. In this case set data->error correctly.
This is in preparation for enabling tuning support which relies on
differentiating between illegal sequence and other errors.
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
[simon: broken out of a larger patch]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r7s72100 SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In moving platforms from board files to DT, there still needs to be a way
to set the ocr_mask setting for the tmio driver during probe. Without this
setting, the probe will fail because the supported voltages are not known.
This patch will also traditional platform registration platforms to
migrate to DT.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci capabilities register can be incorrect. The sdhci-caps-mask
and sdhci-caps dt properties specify which bits of the register are
incorrect and what their values should be. This patch makes the sdhci
driver use those properties to correct the caps during
__sdhci_read_caps.
During __sdhci_read_caps
Use the sdhci-caps-mask property to turn off the incorrect bits of the
sdhci register after reading them.
Use the sdhci-caps to turn on bits after using sdhci-caps-mask to turn
off the incorrect ones.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ST Micro-specific busy detection was made after the assumption
that only this variant supports busy detection. So when doing busy
detection, the host immediately tries to use some ST-specific
register bits.
Since the qualcomm variant also supports some busy detection
schemes, encapsulate the variant flags better in the variant struct
and prepare to add more variants by just providing some bitmasks
to the logic.
Put the entire busy detection logic within an if()-clause in the
mmci_cmd_irq() function so the code is only executed when busy
detection is enabled, and so that it is kept in (almost) one
place, and add comments describing what is going on so the
code can be understood.
Tested on the Ux500 by introducing some prints in the busy
detection path and noticing how the IRQ is enabled, used and
disabled successfully.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There was some confusion in the CPSM (Command Path State Machine)
and DPSM (Data Path State Machine) regarding the naming of the
registers, clarify the meaning of this acronym so the naming is
understandable, and consistently use BIT() to define these fields.
Consequently name the register bit defines MCI_[C|D]PSM_* and
adjust the driver as well.
Include new definitions for a few bits found in a patch from
Srinivas Kandagatla.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for DMA slave map has been added to the s3c24xx-dma
controller in commit 34681d84a0
"dmaengine: s3c24xx: Add dma_slave_map for s3c2440 devices"
This patch converts the s3cmci driver to also use it, so we can
eventually get rid of the exported filter function once all
related DMA clients are updated.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now there are no variant drivers using dw_mci_suspend
and dw_mci_resume, so let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could disable biu clk if gpio card detect available,
or it is a non-removable device.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds runtime PM support for dw_mmc-rockchip.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add dw_mci_runtime_suspend/resume interfaces
and expose it to dw_mci variant driver to support runtime
PM.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.
Reviewed-by: Ritesh Harjani <riteshh@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
VMMC is an optional regulator, which means that mmc_regulator_get_supply
will only return an error in case of a deferred probe, but not when the
regulator is not set in the DT.
However, the sunxi driver assumes that VMMC is always there, and doesn't
check the value of the regulator pointer before using it, which obviously
leads to a (close to) null pointer dereference.
Add proper checks to prevent that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
$
After this patch:
$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
alias: of:N*T*Catmel,sama5d2-sdhciC*
alias: of:N*T*Catmel,sama5d2-sdhci
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
$
After this patch:
$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
alias: of:N*T*Cmediatek,mt8135-mmcC*
alias: of:N*T*Cmediatek,mt8135-mmc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable runtime PM autosuspend for the rtsx_usb_sdmmc driver to avoid the
device being runtime suspended and runtime resumed between each request.
Let's use a default timeout of 50ms, to be consistent with other mmc hosts.
Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
value of ios->timing is not related with SDCHI v3.0. If Controller version
is v3.0, SDHCI_QUIRK_NO_HISPD_BIT is meaningless. To prevent the setting
wrong bit moves into one condition checking. (e.g sdhci-s3c doesn't use
SDHCI_CTRL_HISPD bit, instead using this bit as other purpose.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When dma->start is failed,then it has to fall back to PIO mode
for current transfer.
But Host controller was already set to bits relevant to DMA operation.
If needs to use the PIO mode, Host controller has to stop the DMA
operation. (It's more stable than now.)
When it occurred error, it's not running any request.
Fixes: 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface support")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
mmc0: Card stuck in programming state! __mmc_switch
mmc0: error -110 whilst initialising MMC card
Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.
Signed-off-by: Michael Walle <michael@walle.cc>
Fixes: 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An interrupt may occur right after devm_request_irq() is called and
prior to the spinlock initialization, leading to a kernel oops,
as the interrupt handler uses the spinlock.
In order to prevent this problem, move the spinlock initialization
prior to requesting the interrupts.
Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prevent subsequent commands failing, ensure the cmd and data circuits
are reset after a tuning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the busy response case (i.e. !host->data), an unexpected data interrupt
would result in clearing the data command as though it had completed but
without informing the upper layers and thus resulting in a hang. Fix by
only clearing the data command for data interrupts that are expected.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD line reset during an ongoing data transfer can cause the data transfer
to hang. Fix by delaying the reset until the data transfer is finished.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the "reset" as name of reset controller.
This is for preventing the wrong operation. Even if some SoC has reset
controller, doesn't define "resets" in device-tree.
Then it might be waiting for reset controller and it should be stuck.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the platform_get_irq_byname()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ad81d38710 ("mmc: sdhci-msm: Add support for UHS cards")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_resource can be returned the NULL pointer.
Then regs->start should be referred to NULL Pointer.
devm_ioremap_resource() checks whether res is NULL or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Accesses of the rtsx sdmmc's parent device, which is the rtsx usb device,
must be done when it's runtime resumed. Currently this isn't case when
changing the led, so let's fix this by adding a pm_runtime_get_sync() and
a pm_runtime_put() around those operations.
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The rtsx_usb_sdmmc driver may bail out in its ->set_ios() callback when no
SD card is inserted. This is wrong, as it could cause the device to remain
runtime resumed when it's unused. Fix this behaviour.
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Potentially overflowing expression 1000000 * data->timeout_clks with
type unsigned int is evaluated using 32-bit arithmetic, and then used
in a context that expects an expression of type unsigned long long.
To avoid overflow, cast 1000000U to type unsigned long long.
Special thanks to Coverity.
Fixes: 7f05538af7 ("mmc: sdhci: fix data timeout (part 2)")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- The DMA error interrupt bit is in a different position as
compared to the sdhci standard. This is accounted for in
many cases, but not handled in the case of clearing the
INT_STATUS register by writing a 1 to that location.
- The HOST_CONTROL register is very different as compared to
the sdhci standard. This is accounted for in the write
case, but not when read back out (which it is in the sdhci
code).
Signed-off-by: Dave Russell <david.russell@datasoft.com>
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel controllers (e.g. BXT) might fail to set bus power after a
D3 -> D0 transition due to the present state not yet having propagated.
Retry for up to 2 milliseconds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own sdhci_ops so that device-specific variations
can be implemented without adding quirks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Unlike other cases, sdhci_set_power() does not reflect the default
implementation of the ->set_power() callback. Rename it and create
sdhci_set_power() that is the default implementation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Multi-block data transfers can specify the number of blocks either using a
Set Block Count command (CMD23) or by sending a STOP command (CMD12) after
the required number of blocks has transferred. CMD23 is preferred, but some
cards don't support it. CMD12 with R1b response is used for writes, and
R1 response for reads.
Some SDHCI host controllers give a Transfer Complete (TC) interrupt for the
STOP command (CMD12) whether or not a R1b response has been specified. The
quirk SDHCI_QUIRK2_STOP_WITH_TC identifies those host controllers, but the
implementation only considers the case where the TC interrupt arrives at
the same time as the Command Complete (CC) interrupt. However,
occasionally TC arrives before CC. That is harmless, but does generate an
error message "Got data interrupt 0x00000002 even though no data operation
was in progress".
A simpler approach is to force R1b response onto all STOP commands, because
SDHCI will handle TC before CC in the general case, so do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the vendor's requirement, we shouldn't do any setting for
1.8V Signaling Enable, otherwise the interaction/behaviour between
phy and controller will be undefined. Mostly it works fine if we do
that, but we still see failures. Anyway, let's fix it to meet the
vendor's requirement. The error log looks like:
[ 93.405085] mmc1: unexpected status 0x800900 after switch
[ 93.408474] mmc1: switch to bus width 1 failed
[ 93.408482] mmc1: mmc_select_hs200 failed, error -110
[ 93.408492] mmc1: error -110 during resume (card was removed?)
[ 93.408705] PM: resume of devices complete after 213.453 msecs
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following sparse warning:
drivers/mmc/host/sdhci-of-arasan.c:253:6: warning:
symbol 'sdhci_arasan_reset' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remvoe the deprecated "supports-highspeed" property.
DWMMC controller will not use this property anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
msize and rx_wmark are properly initialized, we dont't
need to assign them again.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's very prone to make mistake as we might forget
to replace all PAGE_SIZEs with new values if we try
to modify the ring buffer size for whatever reasons.
Let's use a macro to define it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The original log didn't figure out that we could still
finish this transfer by PIO mode even if failing to use
DMA. And it should be kept for debug level instead of
error one.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could see an obvious race condition by test that
the former write operation by IDMAC aiming to clear
OWN bit reach right after the later configuration of
the same desc, which makes the IDMAC be in SUSPEND
state as the OWN bit was cleared by the asynchronous
write operation of IDMAC. The bug can be very easy
reproduced on RK3288 or similar when we reduce the
running rate of system buses and keep the CPU running
faster. So as two separate masters, IDMAC and cpu
write the same descriptor stored on the same address,
and this should be protected by adding check of OWN
bit before preparing new descriptors.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We intend to add more check for descriptors when
preparing desc. Let's spilt out the separate body
to make the dw_mci_translate_sglist not so lengthy.
After spliting out these two functions, we could
remove dw_mci_translate_sglist and call both of them
when staring idmac.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci controller on xilinx zynq devices will not function unless
the CD bit is provided. http://www.xilinx.com/support/answers/61064.html
In cases where it is impossible to provide the CD bit in hardware,
setting the controller to test mode and then setting inserted to true
will get the controller to function without the CD bit.
When the device has the property xlnx,fails-without-test-cd the driver
changes the controller to test mode and sets test inserted to true to
make the controller function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to add R1 without CRC support, refactor the bus width routine a
little and extend a quirk check. To support "non-removable;" we need a
workaround which will be hopefully removed when reworking PM soon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
