Commit Graph

485 Commits

Author SHA1 Message Date
Tobias Klauser
8057b96539 ext3: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted here.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-10 19:04:07 +01:00
Eric Sandeen
a4ae309486 ext3: speed up file creates by optimizing rec_len functions
The addition of 64k block capability in the rec_len_from_disk
and rec_len_to_disk functions added a bit of math overhead which
slows down file create workloads needlessly when the architecture
cannot even support 64k blocks, thanks to page size limits.

Similar changes already exist in the ext4 codebase.

The directory entry checking can also be optimized a bit
by sprinkling in some unlikely() conditions to move the
error handling out of line.

bonnie++ sequential file creates on a 512MB ramdisk speeds up
from about 77,000/s to about 82,000/s, about a 6% improvement.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-10 19:04:07 +01:00
Namhyung Kim
156e74312f ext3: Add more journal error check
Check return value of ext3_journal_get_write_acccess() and
ext3_journal_dirty_metadata().

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-10 19:04:06 +01:00
Namhyung Kim
41dc6385bd ext3: Add journal error check in resize.c
Check return value of ext3_journal_get_write_access() and
ext3_journal_dirty_metadata().

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-10 19:04:06 +01:00
Lukas Czerner
9c52749232 ext3: Add FITRIM handling
The ioctl takes fstrim_range structure (defined in include/linux/fs.h) as an
argument specifying a range of filesystem to trim and the minimum size of an
continguous extent to trim. After the FITRIM is done, the number of bytes
passed from the filesystem down the block stack to the device for potential
discard is stored in fstrim_range.len.  This number is a maximum discard amount
from the storage device's perspective, because FITRIM called repeatedly will
keep sending the same sectors for discard.  fstrim_range.len will report the
same potential discard bytes each time, but only sectors which had been written
to between the discards would actually be discarded by the storage device.
Further, the kernel block layer reserves the right to adjust the discard ranges
to fit raid stripe geometry, non-trim capable devices in a LVM setup, etc.
These reductions would not be reflected in fstrim_range.len.

Thus fstrim_range.len can give the user better insight on how much storage
space has potentially been released for wear-leveling, but it needs to be one
of only one criteria the userspace tools take into account when trying to
optimize calls to FITRIM.

Thanks to Greg Freemyer <greg.freemyer@gmail.com> for better commit message.

Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-10 19:04:05 +01:00
Lukas Czerner
b853b96b1d ext3: Add batched discard support for ext3
Walk through allocation groups and trim all free extents. It can be
invoked through FITRIM ioctl on the file system. The main idea is to
provide a way to trim the whole file system if needed, since some SSD's
may suffer from performance loss after the whole device was filled (it
does not mean that fs is full!).

It search for free extents in allocation groups specified by Byte range
start -> start+len. When the free extent is within this range, blocks are
marked as used and then trimmed. Afterwards these blocks are marked as
free in per-group bitmap.

[JK: Fixed up error handling and trimming of a single group]

Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-10 19:03:58 +01:00
Wang Sheng-Hui
6e9510b0e0 ext2,ext3,ext4: clarify comment for extN_xattr_set_handle
Signed-off-by: Wang Sheng-Hui <crosslonelyover@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2011-01-10 12:10:30 -05:00
Nick Piggin
73598611ad ext2,3,4: provide simple rcu-walk ACL implementation
This simple implementation just checks for no ACLs on the inode, and
if so, then the rcu-walk may proceed, otherwise fail it.

Signed-off-by: Nick Piggin <npiggin@kernel.dk>
2011-01-07 17:50:30 +11:00
Nick Piggin
b74c79e993 fs: provide rcu-walk aware permission i_ops
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
2011-01-07 17:50:29 +11:00
Nick Piggin
fa0d7e3de6 fs: icache RCU free inodes
RCU free the struct inode. This will allow:

- Subsequent store-free path walking patch. The inode must be consulted for
  permissions when walking, so an RCU inode reference is a must.
- sb_inode_list_lock to be moved inside i_lock because sb list walkers who want
  to take i_lock no longer need to take sb_inode_list_lock to walk the list in
  the first place. This will simplify and optimize locking.
- Could remove some nested trylock loops in dcache code
- Could potentially simplify things a bit in VM land. Do not need to take the
  page lock to follow page->mapping.

The downsides of this is the performance cost of using RCU. In a simple
creat/unlink microbenchmark, performance drops by about 10% due to inability to
reuse cache-hot slab objects. As iterations increase and RCU freeing starts
kicking over, this increases to about 20%.

In cases where inode lifetimes are longer (ie. many inodes may be allocated
during the average life span of a single inode), a lot of this cache reuse is
not applicable, so the regression caused by this patch is smaller.

The cache-hot regression could largely be avoided by using SLAB_DESTROY_BY_RCU,
however this adds some complexity to list walking and store-free path walking,
so I prefer to implement this at a later date, if it is shown to be a win in
real situations. I haven't found a regression in any non-micro benchmark so I
doubt it will be a problem.

Signed-off-by: Nick Piggin <npiggin@kernel.dk>
2011-01-07 17:50:26 +11:00
Namhyung Kim
ad1857a0e0 ext3: Add journal error check into ext3_rename()
Check return value of ext3_journal_get_write_access() and
ext3_journal_dirty_metadata().

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:16 +01:00
Theodore Ts'o
5026e90b86 ext3: Use search_dirblock() in ext3_dx_find_entry()
Use the search_dirblock() in ext3_dx_find_entry().  It makes the code
easier to read, and it takes advantage of common code.  It also saves
100 bytes or so of text space.

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:15 +01:00
Theodore Ts'o
f0cad89f5e ext3: Avoid uninitialized memory references with a corrupted htree directory
If the first htree directory is missing '.' or '..' but is otherwise a
valid directory, and we do a lookup for '.' or '..', it's possible to
dereference an uninitialized memory pointer in ext3_htree_next_block().
Avoid this.

We avoid this by moving the special case from ext3_dx_find_entry() to
ext3_find_entry(); this also means we can optimize ext3_find_entry()
slightly when NFS looks up "..".

Thanks to Brad Spengler for pointing a Clang warning that led me to
look more closely at this code.  The warning was harmless, but it was
useful in pointing out code that was too ugly to live.  This warning was
also reported by Roman Borisov.

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:15 +01:00
Darrick J. Wong
ad692bf3ea ext3: Return error code from generic_check_addressable
ext3_fill_super should return the error code that generic_check_accessible
returns when an error condition occurs.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:15 +01:00
Namhyung Kim
fbcae8e32d ext3: Add journal error check into ext3_delete_entry()
Check return value of ext3_journal_get_write_access() and
ext3_journal_dirty_metadata().

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:15 +01:00
Namhyung Kim
2b543edae2 ext3: Add error check in ext3_mkdir()
Check return value of ext3_journal_get_write_access, ext3_journal_dirty_metadata
and ext3_mark_inode_dirty. Consolidate error path under new label 'out_clear_inode'
and adjust bh releasing appropriately.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:14 +01:00
Joe Perches
99fbb1e2af fs/ext3/super.c: Use printf extension %pV
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:14 +01:00
Maciej Żenczykowski
31d710a7bd ext3: don't update sb journal_devnum when RO dev
An ext3 filesystem on a read-only device, with an external journal
which is at a different device number then recorded in the superblock
will fail to honor the read-only setting of the device and trigger
a superblock update (write).

For example:
  - ext3 on a software raid which is in read-only mode
  - external journal on a read-write device which has changed device num
  - attempt to mount with -o journal_dev=<new_number>
  - hits BUG_ON(mddev->ro = 1) in md.c

Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2011-01-06 11:52:14 +01:00
Arnd Bergmann
451a3c24b0 BKL: remove extraneous #include <smp_lock.h>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.

Remove this too as a cleanup.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-11-17 08:59:32 -08:00
Tejun Heo
d4d7762995 block: clean up blkdev_get() wrappers and their users
After recent blkdev_get() modifications, open_by_devnum() and
open_bdev_exclusive() are simple wrappers around blkdev_get().
Replace them with blkdev_get_by_dev() and blkdev_get_by_path().

blkdev_get_by_dev() is identical to open_by_devnum().
blkdev_get_by_path() is slightly different in that it doesn't
automatically add %FMODE_EXCL to @mode.

All users are converted.  Most conversions are mechanical and don't
introduce any behavior difference.  There are several exceptions.

* btrfs now sets FMODE_EXCL in btrfs_device->mode, so there's no
  reason to OR it explicitly on blkdev_put().

* gfs2, nilfs2 and the generic mount_bdev() now set FMODE_EXCL in
  sb->s_mode.

* With the above changes, sb->s_mode now always should contain
  FMODE_EXCL.  WARN_ON_ONCE() added to kill_block_super() to detect
  errors.

The new blkdev_get_*() functions are with proper docbook comments.
While at it, add function description to blkdev_get() too.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Joern Engel <joern@lazybastard.org>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
Cc: reiserfs-devel@vger.kernel.org
Cc: xfs-masters@oss.sgi.com
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
2010-11-13 11:55:18 +01:00
Tejun Heo
e525fd89d3 block: make blkdev_get/put() handle exclusive access
Over time, block layer has accumulated a set of APIs dealing with bdev
open, close, claim and release.

* blkdev_get/put() are the primary open and close functions.

* bd_claim/release() deal with exclusive open.

* open/close_bdev_exclusive() are combination of open and claim and
  the other way around, respectively.

* bd_link/unlink_disk_holder() to create and remove holder/slave
  symlinks.

* open_by_devnum() wraps bdget() + blkdev_get().

The interface is a bit confusing and the decoupling of open and claim
makes it impossible to properly guarantee exclusive access as
in-kernel open + claim sequence can disturb the existing exclusive
open even before the block layer knows the current open if for another
exclusive access.  Reorganize the interface such that,

* blkdev_get() is extended to include exclusive access management.
  @holder argument is added and, if is @FMODE_EXCL specified, it will
  gain exclusive access atomically w.r.t. other exclusive accesses.

* blkdev_put() is similarly extended.  It now takes @mode argument and
  if @FMODE_EXCL is set, it releases an exclusive access.  Also, when
  the last exclusive claim is released, the holder/slave symlinks are
  removed automatically.

* bd_claim/release() and close_bdev_exclusive() are no longer
  necessary and either made static or removed.

* bd_link_disk_holder() remains the same but bd_unlink_disk_holder()
  is no longer necessary and removed.

* open_bdev_exclusive() becomes a simple wrapper around lookup_bdev()
  and blkdev_get().  It also has an unexpected extra bdev_read_only()
  test which probably should be moved into blkdev_get().

* open_by_devnum() is modified to take @holder argument and pass it to
  blkdev_get().

Most of bdev open/close operations are unified into blkdev_get/put()
and most exclusive accesses are tested atomically at the open time (as
it should).  This cleans up code and removes some, both valid and
invalid, but unnecessary all the same, corner cases.

open_bdev_exclusive() and open_by_devnum() can use further cleanup -
rename to blkdev_get_by_path() and blkdev_get_by_devt() and drop
special features.  Well, let's leave them for another day.

Most conversions are straight-forward.  drbd conversion is a bit more
involved as there was some reordering, but the logic should stay the
same.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Brown <neilb@suse.de>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: dm-devel@redhat.com
Cc: drbd-dev@lists.linbit.com
Cc: Leo Chen <leochen@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Joern Engel <joern@logfs.org>
Cc: reiserfs-devel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
2010-11-13 11:55:17 +01:00
Al Viro
152a083666 new helper: mount_bdev()
... and switch of the obvious get_sb_bdev() users to ->mount()

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-10-29 04:16:13 -04:00
Linus Torvalds
7d2f280e75 Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (24 commits)
  quota: Fix possible oops in __dquot_initialize()
  ext3: Update kernel-doc comments
  jbd/2: fixed typos
  ext2: fixed typo.
  ext3: Fix debug messages in ext3_group_extend()
  jbd: Convert atomic_inc() to get_bh()
  ext3: Remove misplaced BUFFER_TRACE() in ext3_truncate()
  jbd: Fix debug message in do_get_write_access()
  jbd: Check return value of __getblk()
  ext3: Use DIV_ROUND_UP() on group desc block counting
  ext3: Return proper error code on ext3_fill_super()
  ext3: Remove unnecessary casts on bh->b_data
  ext3: Cleanup ext3_setup_super()
  quota: Fix issuing of warnings from dquot_transfer
  quota: fix dquot_disable vs dquot_transfer race v2
  jbd: Convert bitops to buffer fns
  ext3/jbd: Avoid WARN() messages when failing to write the superblock
  jbd: Use offset_in_page() instead of manual calculation
  jbd: Remove unnecessary goto statement
  jbd: Use printk_ratelimited() in journal_alloc_journal_head()
  ...
2010-10-27 20:13:18 -07:00
Namhyung Kim
a4c18ad2ee ext3: Update kernel-doc comments
Update missing/broken argument descriptions and fix formatting.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:05 +02:00
Namhyung Kim
db50d20b1d ext3: Fix debug messages in ext3_group_extend()
Fix a typo, break long lines and use E3FSBLK on ext3_fsblk_t.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:05 +02:00
Namhyung Kim
bfa01dfbe0 ext3: Remove misplaced BUFFER_TRACE() in ext3_truncate()
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:04 +02:00
Namhyung Kim
81a4e320e6 ext3: Use DIV_ROUND_UP() on group desc block counting
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:04 +02:00
Namhyung Kim
4569cd1b0d ext3: Return proper error code on ext3_fill_super()
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:03 +02:00
Namhyung Kim
57e94d8647 ext3: Remove unnecessary casts on bh->b_data
bh->b_data is already a pointer to char so casts to 'char *' should
be meaningless. Remove them.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:03 +02:00
Namhyung Kim
df0d6b8ff1 ext3: Cleanup ext3_setup_super()
Fix mount-count check to emit warning only if s_max_mnt_count
is greater than 0 according to man tune2fs(8). Also removes
unnecessary casts.

Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:03 +02:00
Darrick J. Wong
dff6825e9f ext3/jbd: Avoid WARN() messages when failing to write the superblock
This fixes a WARN backtrace in mark_buffer_dirty() that occurs during unmount
when the underlying block device is removed.  This bug has been seen on System
Z when removing all paths from a multipath-backed ext3 mount; on System P when
injecting enough PCI EEH errors to make the SCSI controller go offline; and
similar warnings have been seen (and patched) with ext2/ext4.

The super block update from a previous operation has marked the buffer as in
error, and the flag has to be cleared before doing the update. Similar changes
have been made to ext4 by commit 914258bf2c.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-28 01:30:02 +02:00
Al Viro
7de9c6ee3e new helper: ihold()
Clones an existing reference to inode; caller must already hold one.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-10-25 21:26:11 -04:00
Christoph Hellwig
ebdec241d5 fs: kill block_prepare_write
__block_write_begin and block_prepare_write are identical except for slightly
different calling conventions.  Convert all callers to the __block_write_begin
calling conventions and drop block_prepare_write.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-10-25 21:18:20 -04:00
Linus Torvalds
a2887097f2 Merge branch 'for-2.6.37/barrier' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.37/barrier' of git://git.kernel.dk/linux-2.6-block: (46 commits)
  xen-blkfront: disable barrier/flush write support
  Added blk-lib.c and blk-barrier.c was renamed to blk-flush.c
  block: remove BLKDEV_IFL_WAIT
  aic7xxx_old: removed unused 'req' variable
  block: remove the BH_Eopnotsupp flag
  block: remove the BLKDEV_IFL_BARRIER flag
  block: remove the WRITE_BARRIER flag
  swap: do not send discards as barriers
  fat: do not send discards as barriers
  ext4: do not send discards as barriers
  jbd2: replace barriers with explicit flush / FUA usage
  jbd2: Modify ASYNC_COMMIT code to not rely on queue draining on barrier
  jbd: replace barriers with explicit flush / FUA usage
  nilfs2: replace barriers with explicit flush / FUA usage
  reiserfs: replace barriers with explicit flush / FUA usage
  gfs2: replace barriers with explicit flush / FUA usage
  btrfs: replace barriers with explicit flush / FUA usage
  xfs: replace barriers with explicit flush / FUA usage
  block: pass gfp_mask and flags to sb_issue_discard
  dm: convey that all flushes are processed as empty
  ...
2010-10-22 17:07:18 -07:00
Linus Torvalds
79f14b7c56 Merge branch 'vfs' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl
* 'vfs' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl: (30 commits)
  BKL: remove BKL from freevxfs
  BKL: remove BKL from qnx4
  autofs4: Only declare function when CONFIG_COMPAT is defined
  autofs: Only declare function when CONFIG_COMPAT is defined
  ncpfs: Lock socket in ncpfs while setting its callbacks
  fs/locks.c: prepare for BKL removal
  BKL: Remove BKL from ncpfs
  BKL: Remove BKL from OCFS2
  BKL: Remove BKL from squashfs
  BKL: Remove BKL from jffs2
  BKL: Remove BKL from ecryptfs
  BKL: Remove BKL from afs
  BKL: Remove BKL from USB gadgetfs
  BKL: Remove BKL from autofs4
  BKL: Remove BKL from isofs
  BKL: Remove BKL from fat
  BKL: Remove BKL from ext2 filesystem
  BKL: Remove BKL from do_new_mount()
  BKL: Remove BKL from cgroup
  BKL: Remove BKL from NTFS
  ...
2010-10-22 10:52:01 -07:00
Jan Kara
beb37b85b0 ext3: Fix lost extented attributes for inode with ino == 11
If a filesystem has inode size > 128 and someone deletes lost+found and
reuses inode 11 for some other file, extented attributes set for this
inode before umount will get lost after remounting the filesystem. This
is because extended attributes will get stored in an inode but ext3_iget
will ignore them due to workaround of a bug in an old mkfs.

Fix the problem by initializing i_extra_isize to 0 for freshly allocated
inodes where mkfs workaround in ext3_iget applies. This way these inodes
will always store extended attributes in a special block and no problems
occur.

The bug was spotted and a reproduction test provided by:
  Masayoshi MIZUMA <m.mizuma@jp.fujitsu.com>

Reviewed-by: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-10-05 12:20:23 +02:00
Jan Blunck
77b54a46a8 BKL: Remove BKL from ext3_put_super() and ext3_remount()
The BKL lock is protecting the remounting against a potential call to
ext3_put_super(). This could not happen, since this is protected by the
s_umount rw semaphore of struct super_block.

Therefore I think the BKL is protecting nothing here.

Signed-off-by: Jan Blunck <jblunck@infradead.org>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2010-10-04 21:10:37 +02:00
Jan Blunck
d646cf82e9 BKL: Remove BKL from ext3 fill_super()
The BKL is protecting nothing than two memory allocations here.

Signed-off-by: Jan Blunck <jblunck@infradead.org>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2010-10-04 21:10:36 +02:00
Jan Blunck
db71922217 BKL: Explicitly add BKL around get_sb/fill_super
This patch is a preparation necessary to remove the BKL from do_new_mount().
It explicitly adds calls to lock_kernel()/unlock_kernel() around
get_sb/fill_super operations for filesystems that still uses the BKL.

I've read through all the code formerly covered by the BKL inside
do_kern_mount() and have satisfied myself that it doesn't need the BKL
any more.

do_kern_mount() is already called without the BKL when mounting the rootfs
and in nfsctl. do_kern_mount() calls vfs_kern_mount(), which is called
from various places without BKL: simple_pin_fs(), nfs_do_clone_mount()
through nfs_follow_mountpoint(), afs_mntpt_do_automount() through
afs_mntpt_follow_link(). Both later functions are actually the filesystems
follow_link inode operation. vfs_kern_mount() is calling the specified
get_sb function and lets the filesystem do its job by calling the given
fill_super function.

Therefore I think it is safe to push down the BKL from the VFS to the
low-level filesystems get_sb/fill_super operation.

[arnd: do not add the BKL to those file systems that already
       don't use it elsewhere]

Signed-off-by: Jan Blunck <jblunck@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Christoph Hellwig <hch@infradead.org>
2010-10-04 21:10:10 +02:00
Christoph Hellwig
dd3932eddf block: remove BLKDEV_IFL_WAIT
All the blkdev_issue_* helpers can only sanely be used for synchronous
caller.  To issue cache flushes or barriers asynchronously the caller needs
to set up a bio by itself with a completion callback to move the asynchronous
state machine ahead.  So drop the BLKDEV_IFL_WAIT flag that is always
specified when calling blkdev_issue_* and also remove the now unused flags
argument to blkdev_issue_flush and blkdev_issue_zeroout.  For
blkdev_issue_discard we need to keep it for the secure discard flag, which
gains a more descriptive name and loses the bitops vs flag confusion.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-09-16 20:52:58 +02:00
Patrick J. LoPresti
30ca22c70e ext3/ext4: Factor out disk addressability check
As part of adding support for OCFS2 to mount huge volumes, we need to
check that the sector_t and page cache of the system are capable of
addressing the entire volume.

An identical check already appears in ext3 and ext4.  This patch moves
the addressability check into its own function in fs/libfs.c and
modifies ext3 and ext4 to invoke it.

[Edited to -EINVAL instead of BUG_ON() for bad blocksize_bits -- Joel]

Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Cc: linux-ext4@vger.kernel.org
Acked-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
2010-09-10 08:41:42 -07:00
Linus Torvalds
5f248c9c25 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
  no need for list_for_each_entry_safe()/resetting with superblock list
  Fix sget() race with failing mount
  vfs: don't hold s_umount over close_bdev_exclusive() call
  sysv: do not mark superblock dirty on remount
  sysv: do not mark superblock dirty on mount
  btrfs: remove junk sb_dirt change
  BFS: clean up the superblock usage
  AFFS: wait for sb synchronization when needed
  AFFS: clean up dirty flag usage
  cifs: truncate fallout
  mbcache: fix shrinker function return value
  mbcache: Remove unused features
  add f_flags to struct statfs(64)
  pass a struct path to vfs_statfs
  update VFS documentation for method changes.
  All filesystems that need invalidate_inode_buffers() are doing that explicitly
  convert remaining ->clear_inode() to ->evict_inode()
  Make ->drop_inode() just return whether inode needs to be dropped
  fs/inode.c:clear_inode() is gone
  fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
  ...

Fix up trivial conflicts in fs/nilfs2/super.c
2010-08-10 11:26:52 -07:00
Andreas Gruenbacher
2aec7c5232 mbcache: Remove unused features
The mbcache code was written to support a variable number of indexes,
but all the existing users use exactly one index.  Simplify to code to
support only that case.

There are also no users of the cache entry free operation, and none of
the users keep extra data in cache entries.  Remove those features as
well.

Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-08-09 16:48:45 -04:00
Al Viro
ac14a95b52 convert ext3 to ->evict_inode()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-08-09 16:48:03 -04:00
Christoph Hellwig
1025774ce4 remove inode_setattr
Replace inode_setattr with opencoded variants of it in all callers.  This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.

In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:

 spufs: explicitly checks for ATTR_SIZE earlier
 btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
 ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above

In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-08-09 16:47:37 -04:00
Christoph Hellwig
6e1db88d53 introduce __block_write_begin
Split up the block_write_begin implementation - __block_write_begin is a new
trivial wrapper for block_prepare_write that always takes an already
allocated page and can be either called from block_write_begin or filesystem
code that already has a page allocated.  Remove the handling of already
allocated pages from block_write_begin after switching all callers that
do it to __block_write_begin.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-08-09 16:47:32 -04:00
Christoph Hellwig
eafdc7d190 sort out blockdev_direct_IO variants
Move the call to vmtruncate to get rid of accessive blocks to the callers
in prepearation of the new truncate calling sequence.  This was only done
for DIO_LOCKING filesystems, so the __blockdev_direct_IO_newtrunc variant
was not needed anyway.  Get rid of blockdev_direct_IO_no_locking and
its _newtrunc variant while at it as just opencoding the two additional
paramters is shorted than the name suffix.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-08-09 16:47:29 -04:00
Jan Kara
5f11e6a440 ext3: Fix dirtying of journalled buffers in data=journal mode
In data=journal mode, we still use block_write_begin() to prepare page for
writing. This function can occasionally mark buffer dirty which violates
journalling assumptions - when a buffer is part of a transaction, it should be
dirty and a buffer can be already part of a forget list of some transaction
when block_write_begin() gets called. This violation of journalling assumptions
then results in "JBD: Spotted dirty metadata buffer..." warnings.

In fact, temporary dirtying the buffer while the page is still locked does not
really cause problems to the journalling because we won't write the buffer
until the page gets unlocked. So we just have to make sure to clear dirty bits
before unlocking the page.

Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-08-05 21:28:28 +02:00
Dave Chinner
aa32a79638 ext3: default to ordered mode
data=writeback mode is dangerous as it leads to higher data loss and stale data
exposure when systems crash. It should not be the default, especially when all
major distros ensure their ext3 filesystems default to ordered mode. Change the
default mode to the safer data=ordered mode, because we should be caring far
more about avoiding stale data exposure than performance.

CC: linux-ext4@vger.kernel.org
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-07-23 12:50:55 +02:00
Jan Kara
f25f624263 ext3: Avoid filesystem corruption after a crash under heavy delete load
It can happen that ext3_free_branches calls ext3_forget() for an indirect block
in an earlier transaction than a transaction in which we clear pointer to this
indirect block. Thus if we crash before a transaction clearing the block
pointer is committed, we will see indirect block pointing to already freed
blocks and complain during orphan list cleanup.

The fix is simple: Make sure ext3_forget() is called in the transaction
doing block pointer clearing.

This is a backport of an ext4 fix by Amir G. <amir73il@users.sourceforge.net>

Signed-off-by: Jan Kara <jack@suse.cz>
2010-07-21 16:04:26 +02:00
Christoph Hellwig
4c4d390122 ext3: remove vestiges of nobh support
The nobh option was only supported for writeback mode, but given that all
write paths (except mmapped writed) actually create buffer heads, it
effectively was a no-op already.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-07-21 16:01:47 +02:00
Andi Kleen
0411ba7902 ext3: Fix set but unused variables
[tytso@mit.edu: Fix compilation with CONFIG_JBD_DEBUG enabled]

Acked-by: tytso@mit.edu
cc: linux-ext4@vger.kernel.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-07-21 16:01:47 +02:00
Miao Xie
30e2bab2d6 ext3: update ctime when changing the file's permission by setfacl
ext3 didn't update the ctime of the file when its permission was changed.

Steps to reproduce:
 # touch aaa
 # stat -c %Z aaa
 1275289822
 # setfacl -m  'u::x,g::x,o::x' aaa
 # stat -c %Z aaa
 1275289822				<- unchanged

But, according to the spec of the ctime, ext3 must update it.

Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-06-25 01:20:37 +02:00
Linus Torvalds
d28619f156 Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  quota: Convert quota statistics to generic percpu_counter
  ext3 uses rb_node = NULL; to zero rb_root.
  quota: Fixup dquot_transfer
  reiserfs: Fix resuming of quotas on remount read-write
  pohmelfs: Remove dead quota code
  ufs: Remove dead quota code
  udf: Remove dead quota code
  quota: rename default quotactl methods to dquot_
  quota: explicitly set ->dq_op and ->s_qcop
  quota: drop remount argument to ->quota_on and ->quota_off
  quota: move unmount handling into the filesystem
  quota: kill the vfs_dq_off and vfs_dq_quota_on_remount wrappers
  quota: move remount handling into the filesystem
  ocfs2: Fix use after free on remount read-only

Fix up conflicts in fs/ext4/super.c and fs/ufs/file.c
2010-05-30 09:11:11 -07:00
Christoph Hellwig
7ea8085910 drop unused dentry argument to ->fsync
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-05-27 22:05:02 -04:00
Venkatesh Pallipadi
1513b02c8b ext3 uses rb_node = NULL; to zero rb_root.
The problem with this is that 17d9ddc72f ("rbtree: Add support
for augmented rbtrees") in the linux-next tree adds a new field to that
struct which needs to be NULLas well.  This patch uses RB_ROOT as the
intializer so all of the relevant fields will be NULL'd.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-27 17:39:36 +02:00
Christoph Hellwig
287a80958c quota: rename default quotactl methods to dquot_
Follow the dquot_* style used elsewhere in dquot.c.

[Jan Kara: Fixed up missing conversion of ext2]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-24 14:10:17 +02:00
Christoph Hellwig
307ae18a56 quota: drop remount argument to ->quota_on and ->quota_off
Remount handling has fully moved into the filesystem, so all this is
superflous now.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-24 14:09:12 +02:00
Christoph Hellwig
e0ccfd959c quota: move unmount handling into the filesystem
Currently the VFS calls into the quotactl interface for unmounting
filesystems.  This means filesystems with their own quota handling
can't easily distinguish between user-space originating quotaoff
and an unount.  Instead move the responsibily of the unmount handling
into the filesystem to be consistent with all other dquot handling.

Note that we do call dquot_disable a lot later now, e.g. after
a sync_filesystem.  But this is fine as the quota code does all its
writes via blockdev's mapping and that is synced even later.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-24 14:09:12 +02:00
Christoph Hellwig
0f0dd62fdd quota: kill the vfs_dq_off and vfs_dq_quota_on_remount wrappers
Instead of having wrappers in the VFS namespace export the dquot_suspend
and dquot_resume helpers directly.  Also rename vfs_quota_disable to
dquot_disable while we're at it.

[Jan Kara: Moved dquot_suspend to quotaops.h and made it inline]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-24 14:06:40 +02:00
Christoph Hellwig
c79d967de3 quota: move remount handling into the filesystem
Currently do_remount_sb calls into the dquot code to tell it about going
from rw to ro and ro to rw.  Move this code into the filesystem to
not depend on the dquot code in the VFS - note ocfs2 already ignores
these calls and handles remount by itself.  This gets rid of overloading
the quotactl calls and allows to unify the VFS and XFS codepaths in
that area later.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-24 14:06:39 +02:00
Linus Torvalds
e8bebe2f71 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (69 commits)
  fix handling of offsets in cris eeprom.c, get rid of fake on-stack files
  get rid of home-grown mutex in cris eeprom.c
  switch ecryptfs_write() to struct inode *, kill on-stack fake files
  switch ecryptfs_get_locked_page() to struct inode *
  simplify access to ecryptfs inodes in ->readpage() and friends
  AFS: Don't put struct file on the stack
  Ban ecryptfs over ecryptfs
  logfs: replace inode uid,gid,mode initialization with helper function
  ufs: replace inode uid,gid,mode initialization with helper function
  udf: replace inode uid,gid,mode init with helper
  ubifs: replace inode uid,gid,mode initialization with helper function
  sysv: replace inode uid,gid,mode initialization with helper function
  reiserfs: replace inode uid,gid,mode initialization with helper function
  ramfs: replace inode uid,gid,mode initialization with helper function
  omfs: replace inode uid,gid,mode initialization with helper function
  bfs: replace inode uid,gid,mode initialization with helper function
  ocfs2: replace inode uid,gid,mode initialization with helper function
  nilfs2: replace inode uid,gid,mode initialization with helper function
  minix: replace inode uid,gid,mode init with helper
  ext4: replace inode uid,gid,mode init with helper
  ...

Trivial conflict in fs/fs-writeback.c (mark bitfields unsigned)
2010-05-21 19:37:45 -07:00
Dmitry Monakhov
aab99c2c26 ext3: replace inode uid,gid,mode init with helper
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-05-21 18:31:24 -04:00
Stephen Hemminger
d1f21049f9 ext3: constify xattr handlers
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-05-21 18:31:19 -04:00
Jens Axboe
ee9a3607fb Merge branch 'master' into for-2.6.35
Conflicts:
	fs/ext3/fsync.c

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-05-21 21:27:26 +02:00
Dmitry Monakhov
12755627bd quota: unify quota init condition in setattr
Quota must being initialized if size or uid/git changes requested.
But initialization performed in two different places:
in case of i_size file system is responsible for dquot init
, but in case of uid/gid init will be called internally in
dquot_transfer().
This ambiguity makes code harder to understand.
Let's move this logic to one common helper function.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-21 19:30:45 +02:00
Eric Sandeen
0636c73ee7 ext3: make barrier options consistent with ext4
ext4 was updated to accept barrier/nobarrier mount options
in addition to the older barrier=0/1.  The barrier story
is complex enough, we should help people by making the options
the same at least, even if the defaults are different.

This patch allows the barrier/nobarrier mount options for ext3,
while keeping nobarrier the default.

It also unconditionally displays barrier status in show_options,
and prints a message at mount time if barriers are not enabled,
just as ext4 does.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-21 19:30:41 +02:00
Jan Kara
5277970878 ext3: Fix waiting on transaction during fsync
log_start_commit() returns 1 only when it started a transaction
commit. Thus in case transaction commit is already running, we
fail to wait for the commit to finish. Fix the issue by always
waiting for the commit regardless of the log_start_commit return
value.

Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-21 19:30:41 +02:00
Dmitry Monakhov
41d1a636b8 ext3: init statistics after journal recovery v2
Currently block/inode/dir counters are initialized before journal was
recovered. In fact after journal recovery this info will probably
change which results in incorrect numbers returned from statfs(2).
BUG:#15768

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-21 19:30:38 +02:00
Frans van de Wiel
8cef107a1d ext3: Avoid loading bitmaps for full groups during block allocation
There is no point in loading bitmap for groups which are completely full.
This causes noticeable performance problems (and memory pressure) on small
systems with large full filesystem
(http://marc.info/?l=linux-ext4&m=126843108314310&w=2).

Jan Kara: Added a comment and changed check to use cpu-endian value.

Signed-off-by: "Frans van de Wiel" <fvdw@fvdw.eu>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-05-21 19:30:36 +02:00
Dmitry Monakhov
fbd9b09a17 blkdev: generalize flags for blkdev_issue_fn functions
The patch just convert all blkdev_issue_xxx function to common
set of flags. Wait/allocation semantics preserved.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-04-28 19:47:36 +02:00
Dmitry Monakhov
774f03fb2c ext3: symlink must be handled via filesystem specific operation
generic setattr implementation is no longer responsible for
quota transfer so synlinks must be handled via ext3_setattr.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-04-12 21:11:39 +02:00
Tejun Heo
5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Linus Torvalds
de329820e9 ext3: fix broken handling of EXT3_STATE_NEW
In commit 9df93939b7 ("ext3: Use bitops to read/modify
EXT3_I(inode)->i_state") ext3 changed its internal 'i_state' variable to
use bitops for its state handling.  However, unline the same ext4
change, it didn't actually change the name of the field when it changed
the semantics of it.

As a result, an old use of 'i_state' remained in fs/ext3/ialloc.c that
initialized the field to EXT3_STATE_NEW.  And that does not work
_at_all_ when we're now working with individually named bits rather than
values that get masked.  So the code tried to mark the state to be new,
but in actual fact set the field to EXT3_STATE_JDATA.  Which makes no
sense at all, and screws up all the code that checks whether the inode
was newly allocated.

In particular, it made the xattr code unhappy, and caused various random
behavior, like apparently

	https://bugzilla.redhat.com/show_bug.cgi?id=577911

So fix the initialization, and rename the field to match ext4 so that we
don't have this happen again.

Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Daniel J Walsh <dwalsh@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-29 14:30:19 -07:00
Jiri Kosina
318ae2edc3 Merge branch 'for-next' into for-linus
Conflicts:
	Documentation/filesystems/proc.txt
	arch/arm/mach-u300/include/mach/debug-macro.S
	drivers/net/qlge/qlge_ethtool.c
	drivers/net/qlge/qlge_main.c
	drivers/net/typhoon.c
2010-03-08 16:55:37 +01:00
Linus Torvalds
e213e26ab3 Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (33 commits)
  quota: stop using QUOTA_OK / NO_QUOTA
  dquot: cleanup dquot initialize routine
  dquot: move dquot initialization responsibility into the filesystem
  dquot: cleanup dquot drop routine
  dquot: move dquot drop responsibility into the filesystem
  dquot: cleanup dquot transfer routine
  dquot: move dquot transfer responsibility into the filesystem
  dquot: cleanup inode allocation / freeing routines
  dquot: cleanup space allocation / freeing routines
  ext3: add writepage sanity checks
  ext3: Truncate allocated blocks if direct IO write fails to update i_size
  quota: Properly invalidate caches even for filesystems with blocksize < pagesize
  quota: generalize quota transfer interface
  quota: sb_quota state flags cleanup
  jbd: Delay discarding buffers in journal_unmap_buffer
  ext3: quota_write cross block boundary behaviour
  quota: drop permission checks from xfs_fs_set_xstate/xfs_fs_set_xquota
  quota: split out compat_sys_quotactl support from quota.c
  quota: split out netlink notification support from quota.c
  quota: remove invalid optimization from quota_sync_all
  ...

Fixed trivial conflicts in fs/namei.c and fs/ufs/inode.c
2010-03-05 13:20:53 -08:00
Christoph Hellwig
a9185b41a4 pass writeback_control to ->write_inode
This gives the filesystem more information about the writeback that
is happening.  Trond requested this for the NFS unstable write handling,
and other filesystems might benefit from this too by beeing able to
distinguish between the different callers in more detail.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-03-05 13:25:52 -05:00
Christoph Hellwig
871a293155 dquot: cleanup dquot initialize routine
Get rid of the initialize dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.

Rename the now static low-level dquot_initialize helper to __dquot_initialize
and vfs_dq_init to dquot_initialize to have a consistent namespace.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:30 +01:00
Christoph Hellwig
907f4554e2 dquot: move dquot initialization responsibility into the filesystem
Currently various places in the VFS call vfs_dq_init directly.  This means
we tie the quota code into the VFS.  Get rid of that and make the
filesystem responsible for the initialization.   For most metadata operations
this is a straight forward move into the methods, but for truncate and
open it's a bit more complicated.

For truncate we currently only call vfs_dq_init for the sys_truncate case
because open already takes care of it for ftruncate and open(O_TRUNC) - the
new code causes an additional vfs_dq_init for those which is harmless.

For open the initialization is moved from do_filp_open into the open method,
which means it happens slightly earlier now, and only for regular files.
The latter is fine because we don't need to initialize it for operations
on special files, and we already do it as part of the namespace operations
for directories.

Add a dquot_file_open helper that filesystems that support generic quotas
can use to fill in ->open.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:30 +01:00
Christoph Hellwig
9f75475802 dquot: cleanup dquot drop routine
Get rid of the drop dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.

Rename the now static low-level dquot_drop helper to __dquot_drop
and vfs_dq_drop to dquot_drop to have a consistent namespace.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:30 +01:00
Christoph Hellwig
257ba15ced dquot: move dquot drop responsibility into the filesystem
Currently clear_inode calls vfs_dq_drop directly.  This means
we tie the quota code into the VFS.  Get rid of that and make the
filesystem responsible for the drop inside the ->clear_inode
superblock operation.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:29 +01:00
Christoph Hellwig
b43fa8284d dquot: cleanup dquot transfer routine
Get rid of the transfer dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.

Rename the now static low-level dquot_transfer helper to __dquot_transfer
and vfs_dq_transfer to dquot_transfer to have a consistent namespace,
and make the new dquot_transfer return a normal negative errno value
which all callers expect.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:29 +01:00
Christoph Hellwig
63936ddaa1 dquot: cleanup inode allocation / freeing routines
Get rid of the alloc_inode and free_inode dquot operations - they are
always called from the filesystem and if a filesystem really needs
their own (which none currently does) it can just call into it's
own routine directly.

Also get rid of the vfs_dq_alloc/vfs_dq_free wrappers and always
call the lowlevel dquot_alloc_inode / dqout_free_inode routines
directly, which now lose the number argument which is always 1.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:28 +01:00
Christoph Hellwig
5dd4056db8 dquot: cleanup space allocation / freeing routines
Get rid of the alloc_space, free_space, reserve_space, claim_space and
release_rsv dquot operations - they are always called from the filesystem
and if a filesystem really needs their own (which none currently does)
it can just call into it's own routine directly.

Move shared logic into the common __dquot_alloc_space,
dquot_claim_space_nodirty and __dquot_free_space low-level methods,
and rationalize the wrappers around it to move as much as possible
code into the common block for CONFIG_QUOTA vs not.  Also rename
all these helpers to be named dquot_* instead of vfs_dq_*.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:28 +01:00
Dmitry Monakhov
49792c806d ext3: add writepage sanity checks
- There is theoretical possibility to perform writepage on
   RO superblock. Add explicit check for what case.
- Page must being locked before writepage.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:27 +01:00
Jan Kara
7eb4969e04 ext3: Truncate allocated blocks if direct IO write fails to update i_size
We have to truncate blocks allocated to file during direct IO when we
fail to update i_size properly.

Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:27 +01:00
Dmitry Monakhov
e5472147e1 ext3: quota_write cross block boundary behaviour
We always assume what dquot update result in changes in one data block
But ext3_quota_write() function may handle cross block boundary writes
In fact if this ever happen it will result in incorrect journal credits
reservation. And later bug_on triggering. As soon this never happen the
boundary cross loop is NOOP. In order to make things straight
let's remove this loop and assert cross boundary condition.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:26 +01:00
Dmitry Monakhov
e1f5c67a19 ext3: trivial quota cleanup
The patch is aimed to reorganize and simplify quota code a bit.
Quota code is itself complex enouth, but we can make it more readable
in some places:
- Move quota option parsing to separate functions.
- Simplify old-quota and journaled-quota mix check.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:20 +01:00
Dmitry Monakhov
e3c9643597 ext3: mount flags manipulation cleanup
Replace intermediate EXT3_MOUNT_XXX flags manipulation to
corresponding macro.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:20 +01:00
Jan Kara
9df93939b7 ext3: Use bitops to read/modify EXT3_I(inode)->i_state
At several places we modify EXT3_I(inode)->i_state without holding i_mutex
(ext3_release_file, ext3_bmap, ext3_journalled_writepage, ext3_do_update_inode,
...). These modifications are racy and we can lose updates to i_state. So
convert handling of i_state to use bitops which are atomic.

Signed-off-by: Jan Kara <jack@suse.cz>
2010-03-05 00:20:20 +01:00
Thadeu Lima de Souza Cascardo
d6b198bc8a fix ext3/ext4 comment typo compain -> complain
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-02-05 12:22:36 +01:00
Eric Sandeen
96d2a495c2 ext3: Replace lock/unlock_super() with an explicit lock for resizing
Use a separate lock to protect s_groups_count and the other block
group descriptors which get changed via an on-line resize operation,
so we can stop overloading the use of lock_super().

Port of ext4 commit 32ed5058ce by
Theodore Ts'o <tytso@mit.edu>.

CC: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-23 13:44:12 +01:00
Eric Sandeen
b8a052d016 ext3: Replace lock/unlock_super() with an explicit lock for the orphan list
Use a separate lock to protect the orphan list, so we can stop
overloading the use of lock_super().

Port of ext4 commit 3b9d4ed266
by Theodore Ts'o <tytso@mit.edu>.

CC: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-23 13:44:11 +01:00
Eric Sandeen
4854a5f0cb ext3: ext3_mark_recovery_complete() doesn't need to use lock_super
The function ext3_mark_recovery_complete() is called from two call
paths: either (a) while mounting the filesystem, in which case there's
no danger of any other CPU calling write_super() until the mount is
completed, and (b) while remounting the filesystem read-write, in
which case the fs core has already locked the superblock.  This also
allows us to take out a very vile unlock_super()/lock_super() pair in
ext3_remount().

Port of ext4 commit a63c9eb2ce by
Theodore Ts'o <tytso@mit.edu>.

CC: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-23 13:44:11 +01:00
Eric Sandeen
ed505ee454 ext3: Remove outdated comment about lock_super()
ext3_fill_super() is no longer called by read_super(), and it is no
longer called with the superblock locked.  The
unlock_super()/lock_super() is no longer present, so this comment is
entirely superfluous.

Port of ext4 commit 32ed5058ce by
Theodore Ts'o <tytso@mit.edu>.

CC: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-23 13:43:50 +01:00
Dmitry Monakhov
c459001fa4 ext3: quota macros cleanup [V2]
Currently all quota block reservation macros contains hardcoded "2"
aka MAXQUOTAS value. This is no good because in some places it is not
obvious to understand what does this digit represent. Let's introduce
new macro with self descriptive name.

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-23 13:33:54 +01:00
Christoph Hellwig
431547b3c4 sanitize xattr handler prototypes
Add a flags argument to struct xattr_handler and pass it to all xattr
handler methods.  This allows using the same methods for multiple
handlers, e.g. for the ACL methods which perform exactly the same action
for the access and default ACLs, just using a different underlying
attribute.  With a little more groundwork it'll also allow sharing the
methods for the regular user/trusted/secure handlers in extN, ocfs2 and
jffs2 like it's already done for xfs in this patch.

Also change the inode argument to the handlers to a dentry to allow
using the handlers mechnism for filesystems that require it later,
e.g. cifs.

[with GFS2 bits updated by Steven Whitehouse <swhiteho@redhat.com>]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2009-12-16 12:16:49 -05:00
Roel Kluin
8e0eb4011b ext3: PTR_ERR return of wrong pointer in setup_new_group_blocks()
Return the PTR_ERR of the correct pointer.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-10 15:02:55 +01:00
Jan Kara
68eb3db083 ext3: Fix data / filesystem corruption when write fails to copy data
When ext3_write_begin fails after allocating some blocks or
generic_perform_write fails to copy data to write, we truncate blocks already
instantiated beyond i_size. Although these blocks were never inside i_size, we
have to truncate pagecache of these blocks so that corresponding buffers get
unmapped. Otherwise subsequent __block_prepare_write (called because we are
retrying the write) will find the buffers mapped, not call ->get_block, and
thus the page will be backed by already freed blocks leading to filesystem and
data corruption.

Reported-by: James Y Knight <foom@fuhm.net>
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-10 15:02:55 +01:00
Jan Kara
1aeec43432 ext3: Support for vfsv1 quota format
We just have to add proper mount options handling. The rest is handled by
the generic quota code.

CC: linux-ext4@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
2009-12-10 15:02:54 +01:00