Currently, VF driver has two kinds of interrupts, reset & CMDQ RX.
For revision 0x21, according to the UM, each interrupt should be
cleared by write 0 to the corresponding bit, but the implementation
writes 0 to the whole register in fact, it will clear other
interrupt at the same time, then the VF will loss the interrupt.
But for revision 0x20, this interrupt clear register is a read &
write register, for compatible, we just keep the old implementation
for 0x20.
This patch fixes it, also, adds a new register for reading the interrupt
status according to hardware user manual.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: b90fcc5bd9 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling TSO but leaving SG active results is a significant
performance drop. Therefore disable also SG on RTL8168evl.
This restores the original performance.
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the snapshot has to be the same as the size of the region,
therefore no need to pass it again during snapshot creation. Remove the
arg and use region->size instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
octeon_mbox_process_cmd() directly writes the PCI_EXP_DEVCTL_BCR_FLR
bit, which bypasses timing requirements imposed by the PCIe spec.
This patch fixes the function to use the pcie_flr() interface instead.
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate 16kb per rx buffer, so we can avoid some overhead by using
alloc_pages_node directly instead of bothering kmalloc_node. Due to
this change buffers are page-aligned now, therefore the alignment check
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing driver for Spectrum and Spectrum-2 ASICs
to support Spectrum-3 ASIC as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for the Flexible RX Parser feature.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC cores also support the Flexible RX Parser feature. Add the support
for it in the XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC also supports Safety Features. This patch implements the
configuration and handling of this feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for VLAN and Double VLAN Filtering in stmmac.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the VLAN Hash Filtering feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RSS functionality and add the corresponding callbacks in
XGMAC core.
Changes from v1:
- Do not use magic constants (Jakub)
- Use ethtool_rxfh_indir_default() (Jakub)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the TX Queue Priority callback in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the TX Queue Weight callback. In order for this to be active
we also need to set ETS algorithm when configuring Queue.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MMC counters feature in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move tc indirect block to flow_offload and rename
it to flow indirect block.The nf_tables can use the
indr block architecture.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same rationale as for sfc, except that this wasn't performance-tested.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already scored points when handling the RX event, no-one else does this,
and looking at the history it appears this was originally meant to only
score on merges, not on GRO_NORMAL. Moreover, it gets in the way of
changing GRO to not immediately pass GRO_NORMAL skbs to the stack.
Performance testing with four TCP streams received on a single CPU (where
throughput was line rate of 9.4Gbps in all tests) showed a 13.7% reduction
in RX CPU usage (n=6, p=0.03).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported ports in ethtool <eth1> are displayed based on media type.
For media type fibre and twinaxial, port type is "FIBRE". Media type
Base-T is "TP" and media KR is "Backplane".
V1->V2:
Corrected the subject.
Signed-off-by: Rahul Verma <rahulv@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All refcount operations are protected by spinlocks now.
Then the atomic counter can be replaced by a normal int.
This patch depends on PATCH 1/2.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atomic_dec_and_test() is not safe because it is
outside of locks.
Move the locks of t4_smte_free() to its caller,
cxgb4_smt_release() to protect the atomic decrement.
Fixes: 3bdb376e69 ("cxgb4: introduce SMT ops to prepare for SMAC rewrite support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-08-05
This series contains updates to i40e driver only.
Dmitrii adds missing statistic counters for VEB and VEB TC's.
Slawomir adds support for logging the "Disable Firmware LLDP" flag
option and its current status.
Jake fixes an issue where VF's being notified of their link status
before their queues are enabled which was causing issues. So always
report link status down when the VF queues are not enabled. Also adds
future proofing when statistics are added or removed by adding checks to
ensure the data pointer for the strings lines up with the expected
statistics count.
Czeslaw fixes the advertised mode reported in ethtool for FEC, where the
"None BaseR RS" was always being displayed no matter what the mode it
was in. Also added logging information when the PF is entering or
leaving "allmulti" (or promiscuous) mode. Fixed up the logging logic
for VF's when leaving multicast mode to not include unicast as well.
v2: drop Aleksandr's patch (previously patch #2 in the series) to
display the VF MAC address that is set by the VF while community
feedback is addressed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a tunnel packet arrives on the NFP card, its destination MAC is
looked up and MAC index returned for it. This index can help verify the
tunnel by, for example, ensuring that the packet arrived on the expected
port. If the packet is destined for a known MAC that is not connected to a
given physical port then the mac index can have a global value (e.g. when
a series of bonded ports shared the same MAC).
If the packet is to be detunneled at a bridge device or internal port like
an Open vSwitch VLAN port, then it should first match a 'pre-tunnel' rule
to direct it to that internal port.
Use the MAC index to indicate if a packet should match a pre-tunnel rule
before decap is allowed. Do this by tracking the number of internal ports
associated with a MAC address and, if the number if >0, set a bit in the
mac_index to forward the packet to the pre-tunnel table before continuing
with decap.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC addresses along with an identifying index are offloaded to firmware to
allow tunnel decapsulation. If a tunnel packet arrives with a matching
destination MAC address and a verified index, it can continue on the
decapsulation process. This replicates the MAC verifications carried out
in the kernel network stack.
When a netdev is added to a bridge (e.g. OvS) then packets arriving on
that dev are directed through the bridge datapath instead of passing
through the network stack. Therefore, tunnelled packets matching the MAC
of that dev will not be decapped here.
Replicate this behaviour on firmware by removing offloaded MAC addresses
when a MAC representer is added to an OvS bridge. This can prevent any
false positive tunnel decaps.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-tunnel rules are TC flower and OvS rules that forward a packet to the
tunnel end point where it can then pass through the network stack and be
decapsulated. These are required if the tunnel end point is, say, an OvS
internal port.
Currently, firmware determines that a packet is in a tunnel and decaps it
if it has a known destination IP and MAC address. However, this bypasses
the flower pre-tunnel rule and so does not update the stats. Further to
this it ignores VLANs that may exist outside of the tunnel header.
Offload pre-tunnel rules to the NFP. This embeds the pre-tunnel rule into
the tunnel decap process based on (firmware) mac index and VLAN. This
means that decap can be carried out correctly with VLANs and that stats
can be updated for all kernel rules correctly.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-tunnel rules must direct packets to an internal port based on L2
information. Rules that egress to an internal port are already indicated
by a non-NULL device in its nfp_fl_payload struct. Verfiy the rest of the
match fields indicate that the rule is a pre-tunnel rule. This requires a
full match on the destination MAC address, an option VLAN field, and no
specific matches on other lower layer fields (with the exception of L4
proto and flags).
If a rule is identified as a pre-tunnel rule then mark it for offload to
the pre-tunnel table. Similarly, remove it from the pre-tunnel table on
rule deletion. The actual offloading of these commands is left to a
following patch.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-tunnel rules are used when the tunnel end-point is on an 'internal
port'. These rules are used to direct the tunnelled packets (based on outer
header fields) to the internal port where they can be detunnelled. The
rule must send the packet to ingress the internal port at the TC layer.
Currently FW does not support an action to send to ingress so cannot
offload such rules. However, in preparation for populating the pre-tunnel
table to represent such rules, check for rules that send to the ingress of
an internal port and mark them as such. Further validation of such rules
is left to subsequent patches.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP allows the merging of 2 flows together into a single offloaded flow.
In the kernel datapath the packet must match 1 flow, impliment its
actions, recirculate, match the 2nd flow and also impliment its actions.
Merging creates a single flow with all actions from the 2 original flows.
Firmware impliments a tunnel header push as the packet is about to egress
the card. Therefore, if the first merge rule candiate pushes a tunnel,
then the second rule can only have an egress action for a valid merge to
occur (or else the action ordering will be incorrect). This prevents the
pushing of a tunnel header followed by the pushing of a vlan header.
In order to support this behaviour, firmware allows VLAN information to
be encoded in the tunnel push action. If this is non zero then the fw will
push a VLAN after the tunnel header push meaning that 2 such flows with
these actions can be merged (with action order being maintained).
Support tunnel in VLAN pushes by encoding VLAN information in the tunnel
push action of any merge flow requiring this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-08-04
This series contains more updates to fm10k from Jake Keller.
Jake removes the unnecessary initialization of some variables to help
resolve static code checker warnings. Explicitly return success during
resume, since the value of 'err' is always success. Fixed a issue with
incrementing a void pointer, which can produce undefined behavior. Used
the __always_unused macro for function templates that are passed as
parameters in functions, but are not used. Simplified the code by
removing an unnecessary macro in determining the value of NON_Q_VECTORS.
Fixed an issue, using bitwise operations to prevent the low address
overwriting the high portion of the address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize PCIe PHY initialization with vendor driver version 8.047.01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for MAC OCP read-modify-write operations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code piece was inherited from RTL8139 code, the register at
address 0x5c however has a different meaning on RTL8169 and is unused.
So we can remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not try to return a fragment entry from TC list. Otherwise we may not
clean properly allocated entries.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queues >= 4 we use different registers but we were not subtracting
the offset of 4. Fix this.
Found out by Coverity.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixup the XGMAC selftests by correctly finishing the implementation of
set_filter callback.
Result:
$ ethtool -t enp4s0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters -95
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_process_mcc() is invoked in 3 different places and
always with BHs disabled except the be_poll function
but since it's invoked from softirq with BHs
disabled it won't hurt.
v1->v2: added explanation to the patch
v2->v3: add a missing call from be_cmds.c
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to 'kfree_skb()' is missing in the error handling path of
'init_one()'.
This is already present in 'remove_one()' but is missing here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sun4i-emac uses the "phy" property to find the PHY it's supposed to
use. This property was deprecated in favor of "phy-handle" in commit
8c5b094476 ("dt-bindings: net: sun4i-emac: Convert the binding to a
schemas").
Add support for this new property name, and fall back to the old one in
case the device tree hasn't been updated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is relying on zero'ed allocated memory and does not
explicitly call atomic_set() to initialize the ref counts to 0. Add
these atomic_set() calls so that it will be more straight forward
to convert atomic ref counts to refcount_t.
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: <GR-Linux-NIC-Dev@marvell.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
desc_cnt and data_cnt should always be equal. In the case of a dropped
packet desc_cnt was still getting updated (correctly), data_cnt
was not. To eliminate this bug and prevent it from recurring this
patch combines them into one ring level cnt.
Signed-off-by: Catherine Sullivan <csully@google.com>
Reviewed-by: Sagi Shahar <sagis@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unicast log when VF is leaving multicast mode.
Added check of vf->vf_states &
I40E_VF_STATE_MC_PROMISC/I40E_VF_STATE_UC_PROMISC.
Without this commit, leaving multicast mode logs "unset unicast"
in dmsg.
Signed-off-by: Czeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
