The driver will not probe without valid DMA channels so no need to check
if they are valid when the module is removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/mtk-sd.c: In function ‘get_best_delay’:
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.start’ is used uninitialized in this function
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.maxlen’ is used uninitialized in this function
If delay is zero, these fields are indeed not initialized.
Let the compiler preinitialize the whole struct to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit converting pxamci to slot-gpio API inverted the logic of the
read-only gpio. Fix it by inverting the logic again.
Fixes: fd546ee6a7 ("mmc: pxamci: fix card detect with slot-gpio API")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
When card is running with DDR mode, dwmmc needs to set DDR_REG bit at
UHS_REG register.
Before this patch, dwmmc controller doesn't consider this.
If this patch is not applied, CRC or other error shoulds be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to DesignWare DoC file, CardThreshold bit should be
bit[27:16].
So it's correct to use (0xFFF << 16), not (0x1FFF << 16).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "host->dms->ch" pointer is NULL here so we can't use it to print the
error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even if we only use one gpd, we need alloc 2 gpd and make
the gpd->next pointer to the second gpd, or may get gpd checksum
error, this was checked by hardware
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use the ios->timing directly is better
It can reflect current timing and do settings by timing
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable omap_hsmmc for Keystone 2 architecture which reuses the HSMMC
IP found on OMAP platforms.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ACPI HIDs for Intel host controllers including one
supporting HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add some macros for HCON register operations
to make code more readable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC doesn't have a standard power control register, so when
writing this register in stack we should do nothing to avoid
incorrect operation.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This algorithm will try 1 degree increments, since there's no way to tell
what resolution the underlying phase code uses. As an added bonus, doing
many tunings yields better results since some tests are run more than once
(ex: if the underlying driver uses 45 degree increments, the tuning code
will try the same angle more than once).
It will then construct a list of good phase ranges (even ranges that cross
360/0), will pick the biggest range then it will set the sample_clk to the
middle of that range.
We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time (ex 10
degrees) this will not work with the current clock phase framework (which
floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.
If a device has device specific code (like exynos) then that will still
take precedence, otherwise this new code will execute. If the device wants
to tune, but has no sample_clk defined we'll return EIO with an error
message.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've introduced a new helper in the MMC core:
mmc_regulator_set_vqmmc(). Let's use this in dw_mmc. Using this new
helper has some advantages:
1. We get the mmc_regulator_set_vqmmc() behavior of trying to match
VQMMC and VMMC when the signal voltage is 3.3V. This ensures max
compatibility.
2. We get rid of a few more warnings when probing unsupported
voltages.
3. We get rid of some non-dw_mmc specific code in dw_mmc.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Freescale eSDHC driver now supports both little-endian and
big-endian mode eSDHC IPs for ARM and PPC. So, MMC_SDHCI_OF_ESDHC
option needs to be reconfigured.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add another PCI ID for an Intel eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci-pci-core.c:447:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.
- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to hardware spec, validate DDR50 mode
for SDXC.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD19 tuning is also available for DDR50 mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some sdio wifi modules have not been working reliable with the sunxi-mmc
host code. This turns out to be caused by starting new io-rw commands while
the card signals that it is still busy processing a previous command.
This commit adds card-busy detection to the sunxi-mmc driver which together
with recent core changes to check card-busy before starting io-rw commands
fixes the wifi reliability issues on the Cubietruck and other sunxi boards
using sdio wifi.
Reported-by: Eugene K <sigintmailru@gmail.com>
Suggested-by: Eugene K <sigintmailru@gmail.com>
Cc: Eugene K <sigintmailru@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_CAP_RUNTIME_RESUME support to save resume time
Drop unnecessary SDC_ARG write
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The goto is correct and the unreachable "return -EINVAL" should be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_init() will clear all irqs and set the needed irqs. So
logically sdhci_init() should be called before request irq.
If not, some irqs may be triggled and handled wrongly. Take
the following into consideration, after request irq, if
SDIO card interrupt enabled, a sd card in the sd slot will
trigger a mass of interrupt(SDHCI_INT_CARD_INT), because at
this time, the vmmc-regulator still not restore, no voltage
supply for the sd card, so the pin of data0~data3 change and
keep low, interrupt(SDHCI_INT_CARD_INT) will rise up ceaselessly.
Due to we already reguest irq, system will be busy in handling
this endless irq, can't response to other event.
So we should call sdhci_init() before request irq in sd resume.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver prints if the data width is 8-bit but it's using a
binary OR instead of a binary AND so it will always report as
"is_8bit=Y" regardless of the flags in host->mmc->caps.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry to the sdhci_acpi_uids list to detect the SD card
reader on the Asus X205Ta laptop.
dstd table:
Device (SDHC)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "PNP0FFF") // _HID: Hardware ID
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SD Card Controller - 80860F16") // _DDN: DOS Dev
Name (_UID, 0x03) // _UID: Unique ID
Name (RDEP, Package (0x02)
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs the
SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk. Without it, the
internal clock could never stabilised when changing the sd clock
frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Atmel sdhci device needs a new quirk. sdhci_set_clock set the Clock
Control Register to 0 before computing the new value and writing it.
It disables the internal clock which causes a reset mecanism. If we
write the new value before this reset mecanism is done, it will prevent
the stabilisation of the internal clock, so a delay is needed. This
delay is about 2-3 cycles of the base clock. To be safe, a 1 ms delay is
used.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of armada_38x_quirks error, all clocks should be cleaned-up, same
as after mv_conf_mbus_windows failure.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to 'FE-2946959' erratum the clock inversion option is
needed to support slow frequencies when the card input hold time
requirement is high. This setting is not required for high speed
MMC and might cause timing violation.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
shci-pxav3 driver is enabling by default the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not
required for Armada 38x and leads to wrong clock setting in the divider.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Starting with commit 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc") MMC on omap3 stopped working
for legacy booting.
This is because legacy booting sets up some of the resource in the
platform init code, and for optional regulators always seem to
return -EPROBE_DEFER for the legacy booting.
Let's fix the issue by checking for device tree based booting for
now. Then when omap3 boots in device tree only mode, this patch
can be just reverted.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c55d7a0553.
Without reverting this commit we get "unbalanced disables for pbias_mmc_omap4"
errors on omap4430. It seems that 4430 and 4460 behave in a different way for
the PBIAS regulator registers and until that has been debugged further we
cannot rely on the regulator status registers in hardare on 4430.
Fixes: 7d607f9170 ("mmc: host: omap_hsmmc: use
devm_regulator_get_optional() for vmmc")
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move pxamci to mmc slot-gpio API to fix interrupt request.
It fixes the case where the card detection is on a gpio expander, on I2C
for example on zylonite board. In this case, the card detect netsted
interrupt is called from a threaded interrupt. The request_irq() fails,
because a hard irq cannot be a nested interrupt from a threaded
interrupt (set __setup_irq()).
This was tested on zylonite and mioa701 boards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that support for platforms which have optional regulator is added,
remove CONFIG_REGULATOR check in omap_hsmmc.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
vdd voltage is set in mmc core to ios->vdd and vmmc should actually
be set to this voltage. Modify omap_hsmmc_enable_supply
to not take vdd as argument since now it's directly set to
the voltage in ios->vdd.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use regulator_is_enabled of pbias regulator to find pbias regulator
status instead of maintaining a custom bookkeeping
pbias_enabled variable.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enable vmmc_aux regulator only if it is in disabled state and disable
vmmc_aux regulator only if it is in enabled state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the regulator is enabled on boot (checked using regulator_is_enabled),
invoke regulator_enable() so that the usecount reflects the correct
state of the regulator and then disable the regulator so that the
initial state of the regulator is disabled. Avoid using ->set_power,
since set_power also takes care of setting the voltages which is not
needed at this point.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix omap_hsmmc_set_power so that pbias regulator is not enabled
during power off.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions to set pbias and invoke it from omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions for enable/disable supply and invoke it from
omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return error if any of the regulator APIs (regulator_enable,
regulator_disable, regulator_set_voltage) fails in
omap_hsmmc_set_power to avoid undefined behavior.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the unnecessary pbias regulator_set_voltage done after
pbias regulator_disable in omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Instead of using omap_hsmmc_host's vcc and vcc_aux
members, use vmmc and vqmmc present in mmc_host which is present
for the same purpose.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the vmmc regulator provides a valid ocrmask, use it. By this even if
the pdata has a valid ocrmask, it will be overwritten with the ocrmask
of the vmmc regulator.
Also remove the unnecessary compatibility check between the ocrmask in
the pdata and the ocrmask from the vmmc regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Instead of using a local regulator variable
in omap_hsmmc_reg_get() for holding the return value of
devm_regulator_get_optional() and then assigning to omap_hsmmc_host
regulator members: vcc, vcc_aux and pbias, directly use the
omap_hsmmc_host regulator members.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now return error only if the return value of
devm_regulator_get_optional() is not the same as -ENODEV, since with
-EPROBE_DEFER, the regulator can be obtained later and all other
errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since vmmc can be optional for some platforms, use
devm_regulator_get_optional() for vmmc. Now return error only
if the return value of devm_regulator_get_optional() is not the
same as -ENODEV, since with -EPROBE_DEFER, the regulator can be
obtained later and all other errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: ludovic.desroches@atmel.com <ludovic.desroches@atmel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock should be enable when SDHI registers are accessed.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Propagate error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intent appears to be to clear only the bits which are set in status
(by setting them to zero in the ack write), like in the other interrupt
handlers, and not to always clear everything (by always writing zero).
Use the correct not operator.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->sg is only set when we're transferring multiple blocks. Check for
its availibility before dereferencing it in the timeout work debug
print.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We ignore errors from mmc_regulator_get_supply() because the usage of
the regulators is optional for the driver, but we still need to check
for and handle EPROBE_DEFER, like it's done in for example dw_mmc.
Otherwise we might end up not using the specified regulators just
because of probe order.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the compatible string in sdhci-of-arasan.c to
support sdhci-arasan5.1 version of controller. No documented
controller IP version is found in the TRM, so we use ths version
of command queueing engine integrated into this controller by arasan
to specify our controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bb8175a8aa ("mmc: sdhci: clarify DDR timing mode between
SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be
distinguished from SD-UHS, but it missed setting driver type for
MMC_DDR52 timing mode.
So sometimes we get the following error on Marvell BG2Q DMP board:
[ 1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd
response 0x900, card status 0xb00
[ 1.569314] mmcblk0: retrying using single block read
[ 1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd
response 0x900, card status 0x0
[ 1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2
[ 1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd
response 0x900, card status 0x0
[ 1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3
This patches fixes this by adding the missing driver type setting.
Fixes: bb8175a8aa ("mmc: sdhci: clarify DDR timing mode ...")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 250ms timeout is too short.
On my system enabling the oclk takes under 50ms and disabling slightly
over 100ms when idle. Under load disabling the clock can take over
350ms.
This does not make mmc clock gating look like good option to have on
sunxi but the system should not crash with mmc clock gating enabled
nonetheless.
This patch sets the timeout to 750ms.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the current quirk set is for an old FPGA, and this patch corrects
quirks according to real SoC.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.
For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.
This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.
This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.
So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.
So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For eSDHC(version < 2.3), the pre divider only could divide base clock
by 2 at least. Add workaround for this to avoid unexpected issue.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fixes: bd455029d0 ("mmc: sdhci-of-esdhc: Pre divider starts at 1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently one mrq->data maybe execute dma_map_sg() twice
when mmc subsystem prepare over one new request, and the
following log show up:
sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25
In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req
for the first time, and map another dma-memory(2) in sdhci_prepare_data
for the second time. But driver only unmap the dma-memory(2), and
dma-memory(1) never unmapped, which cause the dma memory leak issue.
This patch use another method to map the dma memory for the mrq->data
which can fix this dma memory leak issue.
Fixes: 348487cb28 ("mmc: sdhci: use pipeline mmc requests to improve performance")
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes MMC not working issue on O2Micro/BayHub Host, which
requires transfer mode register to be cleared when sending no DMA
command.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the problem which timeout occurs at the time of command request with
several cards.
The timeout value was insufficient as a verification of several cards,
so it was changed 5 seconds from 2 seconds.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In programmable mode, if the clock frequency is too high, the divider
can be too small to meet the clock frequency requirement especially to
init the SD card. In this case, switch to the divided clock mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.
dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.
We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.
This means that host should get DRTO and DTO interrupt.
But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.
There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.
Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.
So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a
[ 4.991109] ------------[ cut here ]------------
[ 4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[ 4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM
because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.
Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
