Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO line
may loose its state during suspend/resume of the system to save
power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes.
-----BEGIN PGP SIGNATURE-----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=TpW1
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
some new clk drivers and updates for old ones. The diff is pretty
spread out across a handful of different SoC clk drivers for Broadcom, TI,
Qualcomm, Renesas, Rockchip, Samsung, and Allwinner, mostly due to the
introduction of new drivers.
Core:
- New clk bulk get APIs
- Clk divider APIs gained the ability to consider a different parent than
the current one
New Drivers:
- Renesas r8a779{0,1,2,4} CPG/MSSR
- TI Keystone SCI firmware controlled clks and OMAP4 clkctrl
- Qualcomm IPQ8074 SoCs
- Cortina Systems Gemini (SL3516/CS3516)
- Rockchip rk3128 SoCs
- Allwinner A83T clk control units
- Broadcom Stingray SoCs
- CPU clks for Mediatek MT8173/MT2701/MT7623 SoCs
Removed Drivers:
- Old non-DT version of the Realview clk driver
Updates:
- Renesas Kconfig/Makefile cleanups
- Amlogic CEC EE clk support
- Improved Armada 7K/8K cp110 clk support
- Rockchip clk id exposing, critical clk markings
- Samsung converted to clk_hw registration APIs
- Fixes for Samsung exynos5420 audio clks
- USB2 clks for Hisilicon hi3798cv200 SoC and video/camera clks for hi3660
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Yar+
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we've got one core change to introduce a bulk clk_get API,
some new clk drivers and updates for old ones. The diff is pretty
spread out across a handful of different SoC clk drivers for Broadcom,
TI, Qualcomm, Renesas, Rockchip, Samsung, and Allwinner, mostly due to
the introduction of new drivers.
Core:
- New clk bulk get APIs
- Clk divider APIs gained the ability to consider a different parent
than the current one
New Drivers:
- Renesas r8a779{0,1,2,4} CPG/MSSR
- TI Keystone SCI firmware controlled clks and OMAP4 clkctrl
- Qualcomm IPQ8074 SoCs
- Cortina Systems Gemini (SL3516/CS3516)
- Rockchip rk3128 SoCs
- Allwinner A83T clk control units
- Broadcom Stingray SoCs
- CPU clks for Mediatek MT8173/MT2701/MT7623 SoCs
Removed Drivers:
- Old non-DT version of the Realview clk driver
Updates:
- Renesas Kconfig/Makefile cleanups
- Amlogic CEC EE clk support
- Improved Armada 7K/8K cp110 clk support
- Rockchip clk id exposing, critical clk markings
- Samsung converted to clk_hw registration APIs
- Fixes for Samsung exynos5420 audio clks
- USB2 clks for Hisilicon hi3798cv200 SoC and video/camera clks for
hi3660"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (147 commits)
clk: gemini: Read status before using the value
clk: scpi: error when clock fails to register
clk: at91: Add sama5d2 suspend/resume
gpio: dt-bindings: Add documentation for gpio controllers on Armada 7K/8K
clk: keystone: TI_SCI_PROTOCOL is needed for clk driver
clk: samsung: audss: Fix silent hang on Exynos4412 due to disabled EPLL
clk: uniphier: provide NAND controller clock rate
clk: hisilicon: add usb2 clocks for hi3798cv200 SoC
clk: Add Gemini SoC clock controller
clk: iproc: Remove __init marking on iproc_pll_clk_setup()
clk: bcm: Add clocks for Stingray SOC
dt-bindings: clk: Extend binding doc for Stingray SOC
clk: mediatek: export cpu multiplexer clock for MT8173 SoCs
clk: mediatek: export cpu multiplexer clock for MT2701/MT7623 SoCs
clk: mediatek: add missing cpu mux causing Mediatek cpufreq can't work
clk: renesas: cpg-mssr: Use of_device_get_match_data() helper
clk: hi6220: add acpu clock
clk: zx296718: export I2S mux clocks
clk: imx7d: create clocks behind rawnand clock gate
clk: hi3660: Set PPLL2 to 2880M
...
Merge misc updates from Andrew Morton:
- a few hotfixes
- various misc updates
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (108 commits)
mm, memory_hotplug: move movable_node to the hotplug proper
mm, memory_hotplug: drop CONFIG_MOVABLE_NODE
mm, memory_hotplug: drop artificial restriction on online/offline
mm: memcontrol: account slab stats per lruvec
mm: memcontrol: per-lruvec stats infrastructure
mm: memcontrol: use generic mod_memcg_page_state for kmem pages
mm: memcontrol: use the node-native slab memory counters
mm: vmstat: move slab statistics from zone to node counters
mm/zswap.c: delete an error message for a failed memory allocation in zswap_dstmem_prepare()
mm/zswap.c: improve a size determination in zswap_frontswap_init()
mm/zswap.c: delete an error message for a failed memory allocation in zswap_pool_create()
mm/swapfile.c: sort swap entries before free
mm/oom_kill: count global and memory cgroup oom kills
mm: per-cgroup memory reclaim stats
mm: kmemleak: treat vm_struct as alternative reference to vmalloc'ed objects
mm: kmemleak: factor object reference updating out of scan_block()
mm: kmemleak: slightly reduce the size of some structures on 64-bit architectures
mm, mempolicy: don't check cpuset seqlock where it doesn't matter
mm, cpuset: always use seqlock when changing task's nodemask
mm, mempolicy: simplify rebinding mempolicies when updating cpusets
...
Pull user access str* updates from Al Viro:
"uaccess str...() dead code removal"
* 'uaccess.strlen' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
s390 keyboard.c: don't open-code strndup_user()
mips: get rid of unused __strnlen_user()
get rid of unused __strncpy_from_user() instances
kill strlen_user()
Pull misc compat stuff updates from Al Viro:
"This part is basically untangling various compat stuff. Compat
syscalls moved to their native counterparts, getting rid of quite a
bit of double-copying and/or set_fs() uses. A lot of field-by-field
copyin/copyout killed off.
- kernel/compat.c is much closer to containing just the
copyin/copyout of compat structs. Not all compat syscalls are gone
from it yet, but it's getting there.
- ipc/compat_mq.c killed off completely.
- block/compat_ioctl.c cleaned up; floppy compat ioctls moved to
drivers/block/floppy.c where they belong. Yes, there are several
drivers that implement some of the same ioctls. Some are m68k and
one is 32bit-only pmac. drivers/block/floppy.c is the only one in
that bunch that can be built on biarch"
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mqueue: move compat syscalls to native ones
usbdevfs: get rid of field-by-field copyin
compat_hdio_ioctl: get rid of set_fs()
take floppy compat ioctls to sodding floppy.c
ipmi: get rid of field-by-field __get_user()
ipmi: get COMPAT_IPMICTL_RECEIVE_MSG in sync with the native one
rt_sigtimedwait(): move compat to native
select: switch compat_{get,put}_fd_set() to compat_{get,put}_bitmap()
put_compat_rusage(): switch to copy_to_user()
sigpending(): move compat to native
getrlimit()/setrlimit(): move compat to native
times(2): move compat to native
compat_{get,put}_bitmap(): use unsafe_{get,put}_user()
fb_get_fscreeninfo(): don't bother with do_fb_ioctl()
do_sigaltstack(): lift copying to/from userland into callers
take compat_sys_old_getrlimit() to native syscall
trim __ARCH_WANT_SYS_OLD_GETRLIMIT
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls
to ->mapping_error so that the dma_map_ops instances are
more self contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)
-----BEGIN PGP SIGNATURE-----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=0Fso
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements
There is a small conflict in arch/s390 due to an arch-wide field rename.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZW4XTAAoJEL/70l94x66DkhMH/izpk54KI17PtyQ9VYI2sYeZ
BWK6Kl886g3ij4pFi3pECqjDJzWaa3ai+vFfzzpJJ8OkCJT5Rv4LxC5ERltVVmR8
A3T1I/MRktSC0VJLv34daPC2z4Lco/6SPipUpPnL4bE2HATKed4vzoOjQ3tOeGTy
dwi7TFjKwoVDiM7kPPDRnTHqCe5G5n13sZ49dBe9WeJ7ttJauWqoxhlYosCGNPEj
g8ZX8+cvcAhVnz5uFL8roqZ8ygNEQq2mgkU18W8ZZKuiuwR0gdsG0gSBFNTdwIMK
NoreRKMrw0+oLXTIB8SZsoieU6Qi7w3xMAMabe8AJsvYtoersugbOmdxGCr1lsA=
=OD7H
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"PPC:
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
Update my email address
kvm: vmx: allow host to access guest MSR_IA32_BNDCFGS
x86: kvm: mmu: use ept a/d in vmcs02 iff used in vmcs12
kvm: x86: mmu: allow A/D bits to be disabled in an mmu
x86: kvm: mmu: make spte mmio mask more explicit
x86: kvm: mmu: dead code thanks to access tracking
KVM: PPC: Book3S: Fix typo in XICS-on-XIVE state saving code
KVM: PPC: Book3S HV: Close race with testing for signals on guest entry
KVM: PPC: Book3S HV: Simplify dynamic micro-threading code
KVM: x86: remove ignored type attribute
KVM: LAPIC: Fix lapic timer injection delay
KVM: lapic: reorganize restart_apic_timer
KVM: lapic: reorganize start_hv_timer
kvm: nVMX: Check memory operand to INVVPID
KVM: s390: Inject machine check into the nested guest
KVM: s390: Inject machine check into the guest
tools/kvm_stat: add new interactive command 'b'
tools/kvm_stat: add new command line switch '-i'
tools/kvm_stat: fix error on interactive command 'g'
KVM: SVM: suppress unnecessary NMI singlestep on GIF=0 and nested exit
...
A poisoned or migrated hugepage is stored as a swap entry in the page
tables. On architectures that support hugepages consisting of
contiguous page table entries (such as on arm64) this leads to ambiguity
in determining the page table entry to return in huge_pte_offset() when
a poisoned entry is encountered.
Let's remove the ambiguity by adding a size parameter to convey
additional information about the requested address. Also fixup the
definition/usage of huge_pte_offset() throughout the tree.
Link: http://lkml.kernel.org/r/20170522133604.11392-4-punit.agrawal@arm.com
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com> (odd fixer:METAG ARCHITECTURE)
Cc: Ralf Baechle <ralf@linux-mips.org> (supporter:MIPS)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----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=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing huge,
just lots of development by a number of different developers, full
details in the shortlog.
All of these have been in linux-next for a while. There will be a merge
issue with the arm-soc tree in the include/linux/platform_data/atmel.h
file. Stephen has sent out a fixup for it, so it shouldn't be that
difficult to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpZ9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylkTgCfV2HhbxIph/aEL1nJmwW64oCXFrMAoK59ZH65
tBZIosv0d91K1A+mObBT
=adPL
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing
huge, just lots of development by a number of different developers,
full details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty: serial: lpuart: add a more accurate baud rate calculation method
tty: serial: lpuart: add earlycon support for imx7ulp
tty: serial: lpuart: add imx7ulp support
dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
tty: serial: lpuart: add little endian 32 bit register support
tty: serial: lpuart: refactor lpuart32_{read|write} prototype
tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property
serial: imx-serial - move DMA buffer configuration to DT
serial: imx: Enable RTSD only when needed
serial: imx: Remove unused members from imx_port struct
serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
serial: 8250: Fix THRE flag usage for CAP_MINI
tty/serial: meson_uart: update to stable bindings
dt-bindings: serial: Add bindings for the Amlogic Meson UARTs
serial: Delete dead code for CIR serial ports
serial: sirf: make of_device_ids const
serial/mpsc: switch to dma_alloc_attrs
tty: serial: Add Actions Semi Owl UART earlycon
dt-bindings: serial: Document Actions Semi Owl UARTs
tty/serial: atmel: make the driver DT only
...
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
Pull timer updates from Thomas Gleixner:
"A rather large update for timers/timekeeping:
- compat syscall consolidation (Al Viro)
- Posix timer consolidation (Christoph Helwig / Thomas Gleixner)
- Cleanup of the device tree based initialization for clockevents and
clocksources (Daniel Lezcano)
- Consolidation of the FTTMR010 clocksource/event driver (Linus
Walleij)
- The usual set of small fixes and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (93 commits)
timers: Make the cpu base lock raw
clocksource/drivers/mips-gic-timer: Fix an error code in 'gic_clocksource_of_init()'
clocksource/drivers/fsl_ftm_timer: Unmap region obtained by of_iomap
clocksource/drivers/tcb_clksrc: Make IO endian agnostic
clocksource/drivers/sun4i: Switch to the timer-of common init
clocksource/drivers/timer-of: Fix invalid iomap check
Revert "ktime: Simplify ktime_compare implementation"
clocksource/drivers: Fix uninitialized variable use in timer_of_init
kselftests: timers: Add test for frequency step
kselftests: timers: Fix inconsistency-check to not ignore first timestamp
time: Add warning about imminent deprecation of CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Clean up CLOCK_MONOTONIC_RAW time handling
posix-cpu-timers: Make timespec to nsec conversion safe
itimer: Make timeval to nsec conversion range limited
timers: Fix parameter description of try_to_del_timer_sync()
ktime: Simplify ktime_compare implementation
clocksource/drivers/fttmr010: Factor out clock read code
clocksource/drivers/fttmr010: Implement delay timer
clocksource/drivers: Add timer-of common init routine
clocksource/drivers/tcb_clksrc: Save timer context on suspend/resume
...
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=6hNK
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.13
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
Conflicts:
arch/s390/include/asm/kvm_host.h
Since commit 81a76d7119 ("MIPS: Avoid using unwind_stack() with
usermode") show_backtrace() invokes the raw backtracer when
cp0_status & ST0_KSU indicates user mode to fix issues on EVA kernels
where user and kernel address spaces overlap.
However this is used by show_stack() which creates its own pt_regs on
the stack and leaves cp0_status uninitialised in most of the code paths.
This results in the non deterministic use of the raw back tracer
depending on the previous stack content.
show_stack() deals exclusively with kernel mode stacks anyway, so
explicitly initialise regs.cp0_status to KSU_KERNEL (i.e. 0) to ensure
we get a useful backtrace.
Fixes: 81a76d7119 ("MIPS: Avoid using unwind_stack() with usermode")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/16656/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent CPUs from Imagination Technologies such as the I6400 or P6600 are
able to speculatively fetch data from memory into caches. This means
that if used in a system with non-coherent DMA they require that caches
be invalidated after a device performs DMA, and before the CPU reads the
DMA'd data, in order to ensure that stale values weren't speculatively
prefetched.
Such CPUs also introduced Memory Accessibility Attribute Registers
(MAARs) in order to control the regions in which they are allowed to
speculate. Thus we can use the presence of MAARs as a good indication
that the CPU requires the above cache maintenance. Use the presence of
MAARs to determine the result of cpu_needs_post_dma_flush() in the
default case, in order to handle these recent CPUs correctly.
Note that the return type of cpu_needs_post_dma_flush() is changed to
bool, such that it's clearer what's happening when cpu_has_maar is cast
to bool for the return value. If this patch were backported to a
pre-v4.7 kernel then MIPS_CPU_MAAR was 1ull<<34, so when cast to an int
we would incorrectly return 0. It so happens that MIPS_CPU_MAAR is
currently 1ull<<30, so when truncated to an int gives a non-zero value
anyway, but even so the implicit conversion from long long int to bool
makes it clearer to understand what will happen than the implicit
conversion from long long int to int would. The bool return type also
fits this usage better semantically, so seems like an all-round win.
Thanks to Ed for spotting the issue for pre-v4.7 kernels & suggesting
the return type change.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the scheduler sets TIF_NEED_RESCHED & we call into the scheduler
from arch/mips/kernel/entry.S we disable interrupts. This is true
regardless of whether we reach work_resched from syscall_exit_work,
resume_userspace or by looping after calling schedule(). Although we
disable interrupts in these paths we don't call trace_hardirqs_off()
before calling into C code which may acquire locks, and we therefore
leave lockdep with an inconsistent view of whether interrupts are
disabled or not when CONFIG_PROVE_LOCKING & CONFIG_DEBUG_LOCKDEP are
both enabled.
Without tracing this interrupt state lockdep will print warnings such
as the following once a task returns from a syscall via
syscall_exit_partial with TIF_NEED_RESCHED set:
[ 49.927678] ------------[ cut here ]------------
[ 49.934445] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:3687 check_flags.part.41+0x1dc/0x1e8
[ 49.946031] DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
[ 49.946355] CPU: 0 PID: 1 Comm: init Not tainted 4.10.0-00439-gc9fd5d362289-dirty #197
[ 49.963505] Stack : 0000000000000000 ffffffff81bb5d6a 0000000000000006 ffffffff801ce9c4
[ 49.974431] 0000000000000000 0000000000000000 0000000000000000 000000000000004a
[ 49.985300] ffffffff80b7e487 ffffffff80a24498 a8000000ff160000 ffffffff80ede8b8
[ 49.996194] 0000000000000001 0000000000000000 0000000000000000 0000000077c8030c
[ 50.007063] 000000007fd8a510 ffffffff801cd45c 0000000000000000 a8000000ff127c88
[ 50.017945] 0000000000000000 ffffffff801cf928 0000000000000001 ffffffff80a24498
[ 50.028827] 0000000000000000 0000000000000001 0000000000000000 0000000000000000
[ 50.039688] 0000000000000000 a8000000ff127bd0 0000000000000000 ffffffff805509bc
[ 50.050575] 00000000140084e0 0000000000000000 0000000000000000 0000000000040a00
[ 50.061448] 0000000000000000 ffffffff8010e1b0 0000000000000000 ffffffff805509bc
[ 50.072327] ...
[ 50.076087] Call Trace:
[ 50.079869] [<ffffffff8010e1b0>] show_stack+0x80/0xa8
[ 50.086577] [<ffffffff805509bc>] dump_stack+0x10c/0x190
[ 50.093498] [<ffffffff8015dde0>] __warn+0xf0/0x108
[ 50.099889] [<ffffffff8015de34>] warn_slowpath_fmt+0x3c/0x48
[ 50.107241] [<ffffffff801c15b4>] check_flags.part.41+0x1dc/0x1e8
[ 50.114961] [<ffffffff801c239c>] lock_is_held_type+0x8c/0xb0
[ 50.122291] [<ffffffff809461b8>] __schedule+0x8c0/0x10f8
[ 50.129221] [<ffffffff80946a60>] schedule+0x30/0x98
[ 50.135659] [<ffffffff80106278>] work_resched+0x8/0x34
[ 50.142397] ---[ end trace 0cb4f6ef5b99fe21 ]---
[ 50.148405] possible reason: unannotated irqs-off.
[ 50.154600] irq event stamp: 400463
[ 50.159566] hardirqs last enabled at (400463): [<ffffffff8094edc8>] _raw_spin_unlock_irqrestore+0x40/0xa8
[ 50.171981] hardirqs last disabled at (400462): [<ffffffff8094eb98>] _raw_spin_lock_irqsave+0x30/0xb0
[ 50.183897] softirqs last enabled at (400450): [<ffffffff8016580c>] __do_softirq+0x4ac/0x6a8
[ 50.195015] softirqs last disabled at (400425): [<ffffffff80165e78>] irq_exit+0x110/0x128
Fix this by using the TRACE_IRQS_OFF macro to call trace_hardirqs_off()
when CONFIG_TRACE_IRQFLAGS is enabled. This is done before invoking
schedule() following the work_resched label because:
1) Interrupts are disabled regardless of the path we take to reach
work_resched() & schedule().
2) Performing the tracing here avoids the need to do it in paths which
disable interrupts but don't call out to C code before hitting a
path which uses the RESTORE_SOME macro that will call
trace_hardirqs_on() or trace_hardirqs_off() as appropriate.
We call trace_hardirqs_on() using the TRACE_IRQS_ON macro before calling
syscall_trace_leave() for similar reasons, ensuring that lockdep has a
consistent view of state after we re-enable interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/15385/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We allocate memory for a ready_count variable per-CPU, which is accessed
via a cached non-coherent TLB mapping to perform synchronisation between
threads within the core using LL/SC instructions. In order to ensure
that the variable is contained within its own data cache line we
allocate 2 lines worth of memory & align the resulting pointer to a line
boundary. This is however unnecessary, since kmalloc is guaranteed to
return memory which is at least cache-line aligned (see
ARCH_DMA_MINALIGN). Stop the redundant manual alignment.
Besides cleaning up the code & avoiding needless work, this has the side
effect of avoiding an arithmetic error found by Bryan on 64 bit systems
due to the 32 bit size of the former dlinesz. This led the ready_count
variable to have its upper 32b cleared erroneously for MIPS64 kernels,
causing problems when ready_count was later used on MIPS64 via cpuidle.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 3179d37ee1 ("MIPS: pm-cps: add PM state entry code for CPS systems")
Reported-by: Bryan O'Donoghue <bryan.odonoghue@imgtec.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@imgtec.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v3.16+
Patchwork: https://patchwork.linux-mips.org/patch/15383/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In this sequence the 'move' is assumed in the delay slot of the 'beq',
but head.S is in reorder mode and the former gets pushed one 'nop'
farther by the assembler.
The corrected behavior made booting with an UHI supplied dtb erratic.
Fixes: 15f37e1588 ("MIPS: store the appended dtb address in a variable")
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16614/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the new getsockopt(2) option SO_PEERGROUPS on SOL_SOCKET to
retrieve the auxiliary groups of the remote peer. It is designed to
naturally extend SO_PEERCRED. That is, the underlying data is from the
same credentials. Regarding its syntax, it is based on SO_PEERSEC. That
is, if the provided buffer is too small, ERANGE is returned and @optlen
is updated. Otherwise, the information is copied, @optlen is set to the
actual size, and 0 is returned.
While SO_PEERCRED (and thus `struct ucred') already returns the primary
group, it lacks the auxiliary group vector. However, nearly all access
controls (including kernel side VFS and SYSVIPC, but also user-space
polkit, DBus, ...) consider the entire set of groups, rather than just
the primary group. But this is currently not possible with pure
SO_PEERCRED. Instead, user-space has to work around this and query the
system database for the auxiliary groups of a UID retrieved via
SO_PEERCRED.
Unfortunately, there is no race-free way to query the auxiliary groups
of the PID/UID retrieved via SO_PEERCRED. Hence, the current user-space
solution is to use getgrouplist(3p), which itself falls back to NSS and
whatever is configured in nsswitch.conf(3). This effectively checks
which groups we *would* assign to the user if it logged in *now*. On
normal systems it is as easy as reading /etc/group, but with NSS it can
resort to quering network databases (eg., LDAP), using IPC or network
communication.
Long story short: Whenever we want to use auxiliary groups for access
checks on IPC, we need further IPC to talk to the user/group databases,
rather than just relying on SO_PEERCRED and the incoming socket. This
is unfortunate, and might even result in dead-locks if the database
query uses the same IPC as the original request.
So far, those recursions / dead-locks have been avoided by using
primitive IPC for all crucial NSS modules. However, we want to avoid
re-inventing the wheel for each NSS module that might be involved in
user/group queries. Hence, we would preferably make DBus (and other IPC
that supports access-management based on groups) work without resorting
to the user/group database. This new SO_PEERGROUPS ioctl would allow us
to make dbus-daemon work without ever calling into NSS.
Cc: Michal Sekletar <msekleta@redhat.com>
Cc: Simon McVittie <simon.mcvittie@collabora.co.uk>
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a "maybe-uninitialized" build failure in
arch/mips/kvm/tlb.c when KVM, DYNAMIC_DEBUG and JUMP_LABEL are all
enabled. The failure is:
In file included from ./include/linux/printk.h:329:0,
from ./include/linux/kernel.h:13,
from ./include/asm-generic/bug.h:15,
from ./arch/mips/include/asm/bug.h:41,
from ./include/linux/bug.h:4,
from ./include/linux/thread_info.h:11,
from ./include/asm-generic/current.h:4,
from ./arch/mips/include/generated/asm/current.h:1,
from ./include/linux/sched.h:11,
from arch/mips/kvm/tlb.c:13:
arch/mips/kvm/tlb.c: In function ‘kvm_mips_host_tlb_inv’:
./include/linux/dynamic_debug.h:126:3: error: ‘idx_kernel’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
__dynamic_pr_debug(&descriptor, pr_fmt(fmt), \
^~~~~~~~~~~~~~~~~~
arch/mips/kvm/tlb.c:169:16: note: ‘idx_kernel’ was declared here
int idx_user, idx_kernel;
^~~~~~~~~~
There is a similar error relating to "idx_user". Both errors were
observed with GCC 6.
As far as I can tell, it is impossible for either idx_user or idx_kernel
to be uninitialized when they are later read in the calls to kvm_debug,
but to satisfy the compiler, add zero initializers to both variables.
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Fixes: 57e3869cfa ("KVM: MIPS/TLB: Generalise host TLB invalidate to kernel ASID")
Cc: <stable@vger.kernel.org> # 4.11+
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.
This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.
Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.
One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).
Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.
Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The .its targets require information about the kernel binary, such as
its entry point, which is extracted from the vmlinux ELF. We therefore
require that the ELF is built before the .its files are generated.
Declare this requirement in the Makefile such that make will ensure this
is always the case, otherwise in corner cases we can hit issues as the
.its is generated with an incorrect (either invalid or stale) entry
point.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: cf2a5e0bb4 ("MIPS: Support generating Flattened Image Trees (.itb)")
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code handling the pop76 opcode (ie. bnezc & jialc instructions) in
__compute_return_epc_for_insn() needs to set the value of $31 in the
jialc case, which is encoded with rs = 0. However its check to
differentiate bnezc (rs != 0) from jialc (rs = 0) was unfortunately
backwards, meaning that if we emulate a bnezc instruction we clobber $31
& if we emulate a jialc instruction it actually behaves like a jic
instruction.
Fix this by inverting the check of rs to match the way the instructions
are actually encoded.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 28d6f93d20 ("MIPS: Emulate the new MIPS R6 BNEZC and JIALC instructions")
Cc: stable <stable@vger.kernel.org> # v4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config option name is now renamed to 'TIMER_OF' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The function name is now renamed to 'timer_probe' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The CLOCKSOURCE_OF_DECLARE macro is used widely for the timers to declare the
clocksource at early stage. However, this macro is also used to initialize
the clockevent if any, or the clockevent only.
It was originally suggested to declare another macro to initialize a
clockevent, so in order to separate the two entities even they belong to the
same IP. This was not accepted because of the impact on the DT where splitting
a clocksource/clockevent definition does not make sense as it is a Linux
concept not a hardware description.
On the other side, the clocksource has not interrupt declared while the
clockevent has, so it is easy from the driver to know if the description is
for a clockevent or a clocksource, IOW it could be implemented at the driver
level.
So instead of dealing with a named clocksource macro, let's use a more generic
one: TIMER_OF_DECLARE.
The patch has not functional changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When opening the slave end of a PTY, it is not possible for userspace to
safely ensure that /dev/pts/$num is actually a slave (in cases where the
mount namespace in which devpts was mounted is controlled by an
untrusted process). In addition, there are several unresolvable
race conditions if userspace were to attempt to detect attacks through
stat(2) and other similar methods [in addition it is not clear how
userspace could detect attacks involving FUSE].
Resolve this by providing an interface for userpace to safely open the
"peer" end of a PTY file descriptor by using the dentry cached by
devpts. Since it is not possible to have an open master PTY without
having its slave exposed in /dev/pts this interface is safe. This
interface currently does not provide a way to get the master pty (since
it is not clear whether such an interface is safe or even useful).
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Valentin Rothberg <vrothberg@suse.com>
Signed-off-by: Aleksa Sarai <asarai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field has long been "depreciated" and is finally being
removed, so move the driver to use the "correct" dev_groups field
instead for struct bus_type.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ftrace is used with kprobes, it is possible for a kprobe to contain
an invalid location (ie. only initialised to 0 and not to a specific
location in the code). Trying to perform a cache flush on such location
leads to a crash r4k_flush_icache_range().
Fixes: c1bf207d6e ("MIPS: kprobe: Add support.")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16296/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since introduction of tracing for init functions the in_kernel_space()
check is no longer correct, as it ignores the init sections. As a
result, when probes are inserted (and disabled) in the init functions,
a branch instruction is inserted instead of a nop, which is likely to
result in random crashes during boot.
Remove the MIPS-specific in_kernel_space() method and replace it with a
generic core_kernel_text() that also checks for init sections during
system boot stage.
Fixes: 42c269c88d ("ftrace: Allow for function tracing to record init functions on boot up")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16092/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Space reserved for PKMap should span from PKMAP_BASE to FIXADDR_START.
For large page sizes this is not the case as eg. for 64k pages the range
currently defined is from 0xfe000000 to 0x102000000(!!) which obviously
isn't right.
Remove the hardcoded location and set the BASE address as an offset from
FIXADDR_START.
Since all PKMAP ptes have to be placed in a contiguous memory, ensure
that this is the case by placing them all in a single page. This is
achieved by aligning the end address to pkmap pages count pages.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15950/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All PTEs used by PKMAP should be allocated in a contiguous memory area,
but we do not currently have a mechanism to enforce that, so ensure that
we don't try to allocate more entries than would fit in a single page.
Current fixed value of 1024 would not work with XPA enabled when
sizeof(pte_t)==8 and we need two pages to store pte tables.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15949/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
fixrange_init operates at PMD-granularity and expects the addresses to
be PMD-size aligned, but currently that might not be the case for
PKMAP_BASE unless it is defined properly, so ensure a correct alignment
is used before passing the address to fixrange_init.
fixed mappings: only align the start address that is passed to
fixrange_init rather than the value before adding the size, as we may
end up with uninitialised upper part of the range.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All performance counters on I6400 (odd and even) are capable of counting
any of the available events, so drop current logic of using the extra
bit to determine which counter to use.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Fixes: 4e88a86213 ("MIPS: Add cases for CPU_I6400")
Fixes: fd716fca10 ("MIPS: perf: Fix I6400 event numbers")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15991/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A first step in vcpu->requests encapsulation. Additionally, we now
use READ_ONCE() when accessing vcpu->requests, which ensures we
always load vcpu->requests when it's accessed. This is important as
other threads can change it any time. Also, READ_ONCE() documents
that vcpu->requests is used with other threads, likely requiring
memory barriers, which it does.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[ Documented the new use of READ_ONCE() and converted another check
in arch/mips/kvm/vz.c ]
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When CONFIG_ON=n, dummies are provided for of_clk_get() and
of_clk_get_by_name(), but not for of_clk_get_from_provider().
Provide a dummy for the latter, to improve the ability to do
compile-testing. This requires removing the existing dummy in the
Lantiq clock code.
Fixes: 766e6a4ec6 ("clk: add DT clock binding support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Thomas Langer <thomas.langer@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This fixes a regression in commit 4d6501dce0 where I didn't notice
that MIPS and OpenRISC were reinitialising p->{set,clear}_child_tid to
NULL after our initialisation in copy_process().
We can simply get rid of the arch-specific initialisation here since it
is now always done in copy_process() before hitting copy_thread{,_tls}().
Review notes:
- As far as I can tell, copy_process() is the only user of
copy_thread_tls(), which is the only caller of copy_thread() for
architectures that don't implement copy_thread_tls().
- After this patch, there is no arch-specific code touching
p->set_child_tid or p->clear_child_tid whatsoever.
- It may look like MIPS/OpenRISC wanted to always have these fields be
NULL, but that's not true, as copy_process() would unconditionally
set them again _after_ calling copy_thread_tls() before commit
4d6501dce0.
Fixes: 4d6501dce0 ("kthread: Fix use-after-free if kthread fork fails")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net> # MIPS only
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: openrisc@lists.librecores.org
Cc: Jamie Iles <jamie.iles@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The conversion of the hotplug locking to a percpu rwsem unearthed lock
ordering issues all over the place.
The jump_label code has two issues:
1) Nested get_online_cpus() invocations
2) Ordering problems vs. the cpus rwsem and the jump_label_mutex
To cure these, the following lock order has been established;
cpus_rwsem -> jump_label_lock -> text_mutex
Even if not all architectures need protection against CPU hotplug, taking
cpus_rwsem before jump_label_lock is now mandatory in code pathes which
actually modify code and therefor need text_mutex protection.
Move the get_online_cpus() invocations into the core jump label code and
establish the proper lock order where required.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20170524081549.025830817@linutronix.de
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
