-Make raw bayer header size change from 20 to 16 affect rev072a only, my 2
rev012a cams both have a header size of 20
-While testing this I also tested the new exposure setting (good work on
finding the register JF), and after quite a bit of testing have found out the
exact meaning of the register, this patch modifies setexposure to control
the exposure over a much wider range.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using the sonixb driver in a dark room and given that the autoexposure
algorithm starts with a setting most suitable for daylight, the picture
produced by the cam may actually be 100% black leading to a avg_lum value of 0,
so an avg_lum value of 0 does not always signal an exposure settings change
(which it normally does). This patch adds a check for the really black image
case and stops dropping all frames as invalid in this case.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes gspca claim the USB-ID for sn9c101/2 cams with a TAS5110C1B
sensor even if both gspca and sn9c102 are enabled, as these cams are much
better supported under gspca (and extensively tested with gspca).
It also removes an usb-id from sn9c102 for one more unsupported bridge
sensor combo.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Add documentation for some known registers
- Add support for vga modes (320x240, 160x120) for sif sensors
- Remove F_RAW sensor flag raw mode should work on any sensor as its a bridge
only thing and keeping the flag was becoming awkward.
- Fixup ov6650 and pas106 auto exposure window settings
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a memory leak in an error path.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_device_release() does kfree(), which made the following printk()
doing a use-after-free.
printk() first and release then.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds basic support for the Hauppauge Nova-TD-500 84xxx series.
A future patch will allow for one aerial input to supply both tuners.
With the current code, an aerial must be plugged into each antannae input
in order for both tuners to function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This comment helps to make the code more readable.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some DVB drivers are incorrectly assuming that the size of
i2c_adapter.name is I2C_NAME_SIZE. Here's a fix.
Also change strncpy to strlcpy, as the former is error-prone (and was
indeed incorrectly used.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1) Lower the hstart setting for all sensor by 1 so that we generate
(compressed) BGGR data just like sn9c102 does (instead of GBRG data)
2) Add support for raw bayer output in the lowest resolutions (not enough
bandwidth for higher resolutions), this should work with all sensors but
to be sure only enable it for sensors where it has been tested.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Under certain conditions sonixb compressed frame size can get bigger then
the uncompressed size (seen with 0c45:6028), so make the buffers slightly
bigger.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-the usb-id table caried several flags which were not usb-id specific but
sensor specific, add a sensor_data array and move these flag there
-fr_h_sz was being abused to store and check which bridge was being used
instead add a bridge member to the sd struct
-now that we have a sensor_data table use that to store pointers to
init_sequences instead of using switch cases on sd->sensor
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-remove USB-id's from zc0301 for cams for which zc0301.c does not support
the sensor
-remove USB-id's from sn9c102 for cams where sn9c102 does not support the
bridge sensor combination
-no longer make inclusion of usb id's removed from zc0301 and sn9c102
conditional in gspca
-fix conditional inclusion of USB-id's in gspca to also work when the
conflicting drivers are build as a module
-add a number of USB-id's to gspca from various windows .inf files:
0c45:608f from generic sonix sn9c103 inf file (+ ov7630 which we support)
041e:4022 from creative webcam nx pro, same as already supported 041e:401e
0ac8:0301 from generic zc0301 driver which supports many sensors
10fd:804d from typhoon webshot driver (also FlyCAM-USB 300 plus)
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB buffer may be used for DMA and there may be a caching problem
if the buffer is part of the device structure.
Thanks to Alan Stern.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Add usb id for 093a:2624 (pac7302)
-Report some controls to userspace with 7302 only, as they are 7302 only
-Add gain and exposure controls
-Add autogain
-Fix 7302 imaged being mirrored by default
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- the stream must stop when the main application closes the device.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- new function 'init' called on probe and resume
- remove the functions 'open' and 'closed'
- 'stopN' and 'stop0' are optional
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- turn the led of the cam off after plugging in the cam
- move the probe code from open to config, so that if the probe fails
we never register
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- set some controls as disabled instead of copying the device descr.
- in the ov6650 / 7650 exposure code clamp reg 11 before (instead of after)
using it to calculate reg 10.
- disable brightness (instead of ignoring it) for the TAS5110.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- documentation for some registers
- some preparations for adding autogain_n_exposure functionality
- various pac7311 fixes
- disable brightness and colors controls for 7311
- fix contrast control for 7311
- add hflip and vflip controls for 7311
- minimal jpeg header
- proper SOF detection
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If apps pass QAM_AUTO then we need to obey it.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If apps pass QAM_AUTO then we need to obey it.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not a bug as such, but it looks really strange doing this before
checking whether the state structure could be allocated.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues().
If accounting of a queue is in error, logic borrowed from ivtv will cause
an oops when flushing the queues for a stream. This change greatly
simplifies the queue flush logic, and sets the queue back to sane
defaults on a flush.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed a lot of sparse warnings: mostly warnings about shadowed variables
and signed/unsigned mismatches.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes several small issues at vivi register routines:
1) minor and n_devs should be unsigned;
2) n_devs = 0 were not properly handled;
3) if n_devs specify a high number, the driver would just roll back and
won't register any device. The proper behaviour is to keep all succeded
devices registered;
4) both n_devs and minor were using 0 as permissions. Better to have
them with 0444.
With the current patch, if n_devs specify a very large value, it will
register all possible devices. For example, on a machine without any
other V4L drivers loaded, with this patch, we will have something like:
vivi: V4L2 device registered as /dev/video0
vivi: V4L2 device registered as /dev/video1
vivi: V4L2 device registered as /dev/video2
...
vivi: V4L2 device registered as /dev/video31
video_register_device_index: get_index failed
Video Technology Magazine Virtual Video Capture Board ver 0.5.0 successfully loaded.
5) The number of allocated devices on success is now kept at n_devs:
$ cat /sys/module/vivi/parameters/n_devs
32
Thanks to Henne <henne@nachtwindheim.de> for pointing that there were
some issues at vivi.
Cc: Henne <henne@nachtwindheim.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Better check the video_device pointer before using it.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 10-08-08 23:37, Alan Cox wrote:
>
> Would probably make the printk "pms: not enabled, use pms.enable=1 to
> probe"
>
> So you know
> a) What is wittering about not being probed
> b) How to undo it.
>
> But thats trivia really.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The old Mediavision Pro Movie Studio legacy ISA V4L1 driver was found to
hang the boot during Ingo Molnar's testing of randconfig kernels. Have it
require a "pms.enable=1" kernel parameter to enable the driver when
builtin which avoids such problems.
This is a deprecated and, very likely, unused driver. Nothing changes
modular behaviour moreover.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If saa7134_init is run before v4l2_i2c_drv_init (tuner), then
saa7134_board_init2 will try to set the tuner type for devices that don't
exist yet. This moves tuner to before all of the device-specific drivers
so that it's loaded early enough on boot.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
