Convert orion_wdt driver to use watchdog framework API.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
module_platform_driver() replaces module_init() and module_exit()
and makes the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some motherboards like the Advantech ARK3400 documentation
use a non-inverted GPIO pin. We fix this by assuming that
the BIOS will set the Polarity bit for the GPIO correctly
at startup and we keep the Bit-setting intact when we start
and stop the watchdog.
Reported-by: Jean-François Deverge <jf.deverge@gmail.com>
Signed-off-by: Dave Mueller <d.mueller@elsoft.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
OMAP watchdog driver is adapted to runtime PM like a general device
driver but it is not appropriate. It is causing couple of functional
issues.
1. On OMAP4 SYSCLK can't be gated, because of issue with WDTIMER2 module,
which constantly stays in "in transition" state. Value of register
CM_WKUP_WDTIMER2_CLKCTRL is always 0x00010000 in this case.
Issue occurs immediately after first idle, when hwmod framework tries
to disable WDTIMER2 functional clock - "wd_timer2_fck". After this
module falls to "in transition" state, and SYSCLK gating is blocked.
2. Due to runtime PM, watchdog timer may be completely disabled.
In current code base watchdog timer is not disabled only because of
issue 1. Otherwise state of WDTIMER2 module will be "Disabled", and there
will be no interrupts from omap_wdt. In other words watchdog will not
work at all.
Watchdong is a special IP and it should not be disabled otherwise
purpose of it itself is defeated. Watchdog functional clock should
never be disabled. This patch updates the runtime PM handling in
driver so that runtime PM is limited only during probe/shutdown
and suspend/resume.
The patch fixes issue 1 and 2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
ie6xx_wdt_probe() calls ie6xx_wdt_debugfs_exit() as part of
it's error cleanup path, and ie6xx_wdt_debugfs_exit() is
currently annotated __devexit.
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
bcm63xx_wdt was used as a platform_driver but was not suffixed with
_driver, thus causing section mismatches, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Do not use clock-frequency property from parent node.
Use it from watchdog node.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-By: Alejandro Cabrera <acabrera@udio.cujae.edu.cu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make sure we prepare/unprepare the COH901327 watchdog timer
as is required by the clk API especially if you use common
clock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by : Pankaj Jangra <jangra.pankaj9@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Jetway JNF99 motherboard features a F71869 SuperIO chip, but its
watchdog chipset ID appears to be 1007 (as opposed to 0814). Some testing
confirmed it behaves the exact same as 0814. So add this chipset ID to the
module's ID list so that the Fintek watchdog driver can correctly identify
and access it.
Signed-off-by: Justin Wheeler <jwheeler@datademons.com>
Acked-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In commit 7a87982420 we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix printk format warnings:
drivers/watchdog/iTCO_wdt.c:577:3: warning: format '%04llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/watchdog/iTCO_wdt.c:594:3: warning: format '%04llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
drivers/watchdog/iTCO_wdt.c:600:2: warning: format '%04llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
clk_{un}prepare() routines are required for required on some platforms to run
part of clk enable/disable() routines from contexts that can schedule.
This patch adds support for these routines in sp805 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch converts existing sp805 watchdog driver to use already in place
common infrastructure present in watchdog core. With this lot of code goes away.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver adds support for the watchdog functionality provided by
the Dialog Semiconductor DA9052 PMIC chip.
Tested on samsung smdkv6410 and i.mx53 QS boards.
Signed-off-by: Anthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If a driver's watchdog_device struct is part of a dynamically allocated
struct (which it often will be), merely locking the module is not enough,
even with a drivers module locked, the driver can be unbound from the device,
examples:
1) The root user can unbind it through sysfd
2) The i2c bus master driver being unloaded for an i2c watchdog
I will gladly admit that these are corner cases, but we still need to handle
them correctly.
The fix for this consists of 2 parts:
1) Add ref / unref operations, so that the driver can refcount the struct
holding the watchdog_device struct and delay freeing it until any
open filehandles referring to it are closed
2) Most driver operations will do IO on the device and the driver should not
do any IO on the device after it has been unbound. Rather then letting each
driver deal with this internally, it is better to ensure at the watchdog
core level that no operations (other then unref) will get called after
the driver has called watchdog_unregister_device(). This actually is the
bulk of this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch fixes some potential multithreading issues, despite only
allowing one process to open the /dev/watchdog device, we can still get
called multiple times at the same time, since a program could be using thread,
or could share the fd after a fork.
This causes 2 potential problems:
1) watchdog_start / open do an unlocked test_n_set / test_n_clear,
if these 2 race, the watchdog could be stopped while the active
bit indicates it is running or visa versa.
2) Most watchdog_dev drivers probably assume that only one
watchdog-op will get called at a time, this is not necessary
true atm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Rewrite and extend the wrapper code so that we can easily introduce
locking (this to be able to prevent potential multithreading issues).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
While they are registered all our watchdogs now have a valid device object
so we can in turn use that to report problems nicely.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Create the watchdog class and it's associated devices.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We keep the old /dev/watchdog interface file for the first watchdog via
miscdev. This is basically a cut and paste of the relevant interface code
from the rtc driver layer tweaked for watchdog.
Revised to fix problems noted by Hans de Goede
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog_core include file should have been named
watchdog_core.h and not watchdog_dev.h . Correct this.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some watchdog may need to check if watchdog is ACTIVE or not, for example in
their suspend/resume hooks.
This patch adds this routine and changes the core drivers to use it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Include the private watchdog_dev.h header to pickup the prototypes for the
watchdog_dev_register/unregister functions.
This quiets the following sparse warnings:
warning: symbol 'watchdog_dev_register' was not declared. Should it be static?
warning: symbol 'watchdog_dev_unregister' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Pull first set of watchdog updates from Wim Van Sebroeck:
"This pull contains:
- The removal of ixp2000_wdt
- The addition of ie6xx_wdt
- Some documentation fixes
- Small fixes and improvements
(Note: Part 2 will contain generic watchdog core changes + conversion
of some more drivers)"
* git://www.linux-watchdog.org/linux-watchdog:
Documentation/watchdog: Fix the file descriptor leak when no cmdline arg given
Documentation/watchdog: close the fd when cmdline arg given
Documentation/watchdog: Fix a small typo
watchdog: s3c2410_wdt: Set timeout to actually achieved timeout
watchdog: wm831x: Convert to gpio_request_one()
watchdog: via_wdt: depends on PCI
watchdog: ie6xx_wdt needs io.h
watchdog: ie6xx_wdt.c: fix printk format warning
watchdog: Add watchdog driver for Intel Atom E6XX
watchdog: it87_wdt: Add support for IT8728F watchdog.
watchdog: i6300esb: don't depend on X86
watchdog: Use module_pci_driver
watchdog: sch311x_wdt.c: Remove RESGEN
watchdog: s3c2410-wdt: Use of_match_ptr().
watchdog: Device tree support for pnx4008-wdt
watchdog: ar7_wdt.c: use devm_request_and_ioremap
watchdog: remove ixp2000 driver
watchdog: sp5100_tco.c: quiet sparse noise about using plain integer was NULL pointer
- New CPUs: SH7734 (SH-4A), SH7264 and SH7269 (SH-2A)
- New boards: RSK2+SH7264, RSK2+SH7269
- Unbreaking kgdb for SMP
- Consolidation of _32/_64 page fault handling.
- watchdog and legacy DMA chainsawing, part 1
- Conversion to evt2irq() hwirq lookup, to support relocation
of vectored IRQs for irqdomains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk+7gb4ACgkQGkmNcg7/o7hoPQCgvdQGi9dk3ewIBX9LQ9mL6L81
ls8An3PMKi9fHANnztVUAheP1U2DEanJ
=v/VS
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt:
- New CPUs: SH7734 (SH-4A), SH7264 and SH7269 (SH-2A)
- New boards: RSK2+SH7264, RSK2+SH7269
- Unbreaking kgdb for SMP
- Consolidation of _32/_64 page fault handling.
- watchdog and legacy DMA chainsawing, part 1
- Conversion to evt2irq() hwirq lookup, to support relocation of
vectored IRQs for irqdomains.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (98 commits)
sh: intc: Kill off special reservation interface.
sh: Enable PIO API for hp6xx and se770x.
sh: Kill off machvec IRQ hinting.
sh: dma: More legacy cpu dma chainsawing.
sh: Kill off MAX_DMA_ADDRESS leftovers.
sh: Tidy up some of the cpu legacy dma header mess.
sh: Move sh4a dma header from cpu-sh4 to cpu-sh4a.
sh64: Fix up vmalloc fault range check.
Revert "sh: Ensure fixmap and store queue space can co-exist."
serial: sh-sci: Fix for port types without BRI interrupts.
sh: legacy PCI evt2irq migration.
sh: cpu dma evt2irq migration.
sh: sh7763rdp evt2irq migration.
sh: sdk7780 evt2irq migration.
sh: migor evt2irq migration.
sh: landisk evt2irq migration.
sh: kfr2r09 evt2irq migration.
sh: ecovec24 evt2irq migration.
sh: ap325rxa evt2irq migration.
sh: urquell evt2irq migration.
...
While rebasing my "watchdog_dev: Let the driver update the timeout field on
set_timeout success" patch (before I noticed it was already picked up by Wim),
I noticed that the s3c2410_wdt driver may not always have a 1 second
resolution, this patch changes s3c2410wdt_set_heartbeat to update the
timeout to the actually achieved timeout.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
via_wdt is a PCI driver so it should depend on PCI so that
it will not cause build errors.
drivers/watchdog/via_wdt.c:256:1: warning: data definition has no type or storage class
drivers/watchdog/via_wdt.c:256:1: warning: type defaults to 'int' in declaration of 'module_pci_driver'
drivers/watchdog/via_wdt.c:256:1: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix build error by including <linux/io.h>:
drivers/watchdog/ie6xx_wdt.c:97:2: error: implicit declaration of function 'outb'
drivers/watchdog/ie6xx_wdt.c:133:2: error: implicit declaration of function 'outl'
drivers/watchdog/ie6xx_wdt.c:161:2: error: implicit declaration of function 'inb'
drivers/watchdog/ie6xx_wdt.c:199:3: error: implicit declaration of function 'inl'
drivers/watchdog/ie6xx_wdt.c:203:3: error: implicit declaration of function 'inw'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix printk format warning; use cast to u64 since resource_size_t can
be either u32 or u64.
drivers/watchdog/ie6xx_wdt.c:261:4: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add driver for the watchdog timer built into the
Intel Atom E6XX (TunnelCreek) processor.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This works the same way IT8721F works, but it supports WDT_PWROK
(checked on the datasheet).
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
i6300esb is on of the watchdogs QEMU can emulate. It is also available
when emulating ARM. The driver works without problems and is quite
useful to test userspace dealing with /dev/watchdog.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch converts the PCI watchdog drivers so that they use the
module_pci_driver() macro. This makes the code smaller and simpler.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Marc Vertes <marc.vertes@sigfox.com>
The SCH311x chip contains 2 watchdogs. One is the watchdog programmable
by the runtime register at address 0x65-0x68, the other is the watchdog
inside the power on reset generator. This second watchdog has a fixed
timeout value of ~1.6 seconds and is configurable only by the RESGEN
register.
The BIOS normally takes care of the RESGEN watchdog and disables it (at
least) before the OS is booted.
Unfortunately the sch311x_wdt driver clears bit 0 of the RESGEN register
which has the effect that at the latest 1.6 seconds later, a POR is
triggered.
The attached patch fixes this problem by completely removing any
reference to the RESGEN watchdog from the sch311x_wdt driver.
Signed-off-by: Dave Mueller <d.mueller@elsoft.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds device tree support to pnx4008-wdt.c
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Combine request_region and ioremap into devm_request_and_ioremap. This has
the effect of fixing a missing iounmap on the failure of clk_get.
This also introduces a call to clk_put and clears the vbus_clk variable in
the case of failure or device removal.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The platform is removed, so there are no users of this driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pointers should not be compared to plain integers.
Quiets the sparse warning:
warning: Using plain integer as NULL pointer
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
Pull core locking updates from Ingo Molnar:
"This update:
- extends and simplifies x86 NMI callback handling code to enhance
and fix the HP hw-watchdog driver
- simplifies the x86 NMI callback handling code to fix a kmemcheck
bug.
- enhances the hung-task debugger"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Fix the type of the nmiaction.flags field
x86/nmi: Fix page faults by nmiaction if kmemcheck is enabled
x86/nmi: Add new NMI queues to deal with IO_CHK and SERR
watchdog, hpwdt: Remove priority option for NMI callback
hung task debugging: Inject NMI when hung and going to panic
