Fix leak in error path.
Signed-off-by: Peiwei Hu <jlu.hpw@foxmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
commit f0c15b360f ("media: ir_toy: prevent device from hanging during
transmit") removed a cpu_to_be16() cast, which causes a sparse warning.
Fixes: f0c15b360f ("media: ir_toy: prevent device from hanging during transmit")
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the IR Toy is receiving IR while a transmit is done, it may end up
hanging. We can prevent this from happening by re-entering sample mode
just before issuing the transmit command.
Link: https://github.com/bengtmartensson/HarcHardware/discussions/25
Cc: stable@vger.kernel.org
[mchehab: renamed: s/STATE_RESET/STATE_COMMAND_NO_RESP/ ]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This causes the same urb to resubmitted continuously, hogging up a cpu.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After sending the start transmit command, the device is supposed to
respond with the length of the buffer which can be sent. There might
be some residual ir data there.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ir_toy allows the transmit carrier to be specified.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This device is also supported.
Cc: stable@vger.kernel.org
Tested-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.
Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.
Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.
This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
