Since the PPv2 controller has multiple TX queues, we can spread traffic
by assining TX queues to CPUs, allowing to use XPS to balance egress
traffic between CPUs.
Suggested-by : Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the explicit call to netif_carrier_off() in PPv2's
open() path, as this is now handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mvpp2_percpu_read/write/... functions aren't really per-cpu but
per s/w thread, rename them to include 'thread' instead of 'percpu'.
This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 network controller has 9 internal threads. The driver
works fine when there are less CPUs available than threads. This isn't
true if more CPUs are available. As this is a valid use case, handle
this particular case.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch maps all uses of the CPU to threads. All this_cpu calls are
replaced, and all smp_processor_id() calls are wrapped into the
indirection.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the Marvell PPv2 driver to stop using directly the
CPU number to access per-thread registers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Marvell PPv2 driver the mvpp2_read_relaxed function is only used
in a single file. Make it static and remove its prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 driver has per-cpu functions. As they only are used in
the main file, make them static and remove their prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the PPv2 driver so that all CPU variables are unsigned, as it
makes no sense to have a negative CPU number. This patch is cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2.2 engine only has 8 Rx queues per CPU, while PPv2.1 has
16 of them. This patch updates the code so that the Rx queues mask width
is selected given the version of the network controller used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the probing function so that the queue mode isn't
updated while probing, as the driver would silently end up using a
configuration not wanted by the user. The patch adds an extra check to
validate the chosen queue mode instead, and the driver will fail to
probe if the configuration is invalid.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the IRQs in the Marvell PPv2 driver as their current
names match the way they are used in software. But this will change in
the future, and those IRQs have nothing to do with Rx/Tx interrupts
(this can be configured). The new binding also describe more interrupts
as some where left out.
The old binding support is kept for backward compatibility.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net drivers using phylink shouldn't mess with the link carrier
themselves and should let phylink manage it. The mvpp2 driver wasn't
following this best practice as the mac_config() function made calls to
change the link carrier state. This led to wrongly reported carrier link
state which then triggered other issues. This patch fixes this
behaviour.
But the PPv2 driver relied on this misbehaviour in two cases: for fixed
links and when not using phylink (ACPI mode). The later was fixed by
adding an explicit call to link_up(), which when the ACPI mode will use
phylink should be removed.
The fixed link case was relying on the mac_config() function to set the
link up, as we found an issue in phylink_start() which assumes the
carrier is off. If not, the link_up() function is never called. To fix
this, a call to netif_carrier_off() is added just before phylink_start()
so that we do not introduce a regression in the driver.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without a valid of_node in struct device we can't find the mvpp2 port
device by its DT node. Specifically, this breaks
of_find_net_device_by_node().
For example, the Armada 8040 based Clearfog GT-8K uses Marvell 88E6141
switch connected to the &cp1_eth2 port:
&cp1_mdio {
...
switch0: switch0@4 {
compatible = "marvell,mv88e6085";
...
ports {
...
port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp1_eth2>;
};
};
};
};
Without this patch, dsa_register_switch() returns -EPROBE_DEFER because
of_find_net_device_by_node() can't find the device_node of the &cp1_eth2
device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 Packer Header Parser has a TCAM based filter, that is not
trivial to configure and debug. Being able to dump TCAM entries from
userspace can be really helpful to help development of new features
and debug existing ones.
This commit adds a basic debugfs interface for the PPv2 driver, focusing
on TCAM related features.
<mnt>/mvpp2/ --- f2000000.ethernet
\- f4000000.ethernet --- parser --- 000 ...
| \- 001
| \- ...
| \- 255 --- ai
| \- header_data
| \- lookup_id
| \- sram
| \- valid
\- eth1 ...
\- eth2 --- mac_filter
\- parser_entries
\- vid_filter
There's one directory per PPv2 instance, named after pdev->name to make
sure names are uniques. In each of these directories, there's :
- one directory per interface on the controller, each containing :
- "mac_filter", which lists all filtered addresses for this port
(based on TCAM, not on the kernel's uc / mc lists)
- "parser_entries", which lists the indices of all valid TCAM
entries that have this port in their port map
- "vid_filter", which lists the vids allowed on this port, based on
TCAM
- one "parser" directory (the parser is common to all ports), containing :
- one directory per TCAM entry (256 of them, from 0 to 255), each
containing :
- "ai" : Contains the 1 byte Additional Info field from TCAM, and
- "header_data" : Contains the 8 bytes Header Data extracted from
the packet
- "lookup_id" : Contains the 4 bits LU_ID
- "sram" : contains the raw SRAM data, which is the result of the TCAM
lookup. This readonly at the moment.
- "valid" : Indicates if the entry is valid of not.
All entries are read-only, and everything is output in hex form.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the appropriate SPDX license identifiers and drop the license text.
This patch is only cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows setting the RSS hash generation parameters from
ethtool. When setting parameters for a given flow type from ethtool
(e.g. tcp4), all the corresponding flows in the flow table are updated,
according to the supported hash parameters.
For example, when configuring TCP over IPv4 hash parameters to be
src/dst IP + src/dst port ("ethtool -N eth0 rx-flow-hash tcp4 sdfn"),
we only set the "src/dst port" hash parameters on the non-fragmented TCP
over IPv4 flows.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the classification action that can be performed is to compute a
hash of the packet header based on some header fields, and lookup a RSS
table based on this hash to determine the final RxQ.
This is done by adding one lookup entry per flow per port, so that we
can configure the hash generation parameters for each flow and each
port.
There are 2 possible engines that can be used for RSS hash generation :
- C3HA, that generates a hash based on up to 4 header-extracted fields
- C3HB, that does the same as c3HA, but also includes L4 info in the hash
There are a lot of fields that can be extracted from the header. For now,
we only use the ones that we can configure using ethtool :
- DST MAC address
- L3 info
- Source IP
- Destination IP
- Source port
- Destination port
The C3HB engine is selected when we use L4 fields (src/dst port).
Header parser Dec table
Ingress pkt +-------------+ flow id +----------------------------+
------------->| TCAM + SRAM |-------->|TCP IPv4 w/ VLAN, not frag |
+-------------+ |TCP IPv4 w/o VLAN, not frag |
|TCP IPv4 w/ VLAN, frag |--+
|etc. | |
+----------------------------+ |
|
Flow table |
+---------+ +------------+ +--------------------------+ |
| RSS tbl |<--| Classifier |<--------| flow 0: C2 lookup | |
+---------+ +------------+ | C3 lookup port 0 | |
| | | C3 lookup port 1 | |
+-----------+ +-------------+ | ... | |
| C2 engine | | C3H engines | | flow 1: C2 lookup |<--+
+-----------+ +-------------+ | C3 lookup port 0 |
| ... |
| ... |
| flow 51 : C2 lookup |
| ... |
+--------------------------+
The C2 engine also gains the role of enabling and disabling the RSS
table lookup for this packet.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp22_init_rss function configures the RSS parameters for each port, so
rename it accordingly. Since this function relies on classifier
configuration, move its call right after the classifier config.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the RSS indirection table support, allowing to use the
ethtool -x and -X options to dump and set this table.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
[Maxime: Small warning fixes, use one table per port]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a dedicated #define that indicates the number of rx queues per
port per cpu, this commit removes a harcoded use of that value
This doesn't fix any runtime bugs since the harcoded value matches the
expected value.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since RSS only applies when we have per-cpu rx queues, it should only
be enabled when the driver is configured to make use of multi-queue
mode.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi queue mode is needed to have RSS available, and offers some
nice advantages, being able to have one rx queue vector per CPU.
This mode has been usable through the use of a module parameter, this
commit makes it the default value.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 driver defines 2 "queue_modes" :
- QDIST_SINGLE_MODE, where each port share one rx queue vector
between all CPUs
- QDIST_MULTI_MODE, where each port has one rx queue vector per CPU.
Multi queue mode isn't available on PPv2.1, make sure we fallback to
single mode when running on this revision.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the skb->protocol field, we have to make sure we use the
proper endianness using htons, and not swab16.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 controller always expect descriptors to be in little endian. We
must therefore force descriptors to use that format, and convert to the
host endianness when necessary.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: db9d7d36ee ("net: mvpp2: Split the PPv2 driver to a dedicated directory")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mvpp2 driver is growing, move this driver to a dedicated
directory and split it into several files.
Since this driver has a lot of register defines and structure
definitions, it can benefit from having all of this into a dedicated
header file, named mvpp2.h.
A good chunk of the mvpp2 code is dedicated to Header Parser handling, so
we introduce mvpp2_prs.h where all Header Parser definitions are located,
and mvpp2_prs.c containing the related code.
In the same way, mvpp2_cls.h and mvpp2_cls.c are created to contain
Classifier and RSS related code.
The former 'mvpp2.c' file is renamed 'mvpp2_main.c' so that we can keep
the driver binary named 'mvpp2'.
This commit is only about spliting the driver into multiple files and
doesn't introduce any new function, feature or fix besides removing
'static' keywords when needed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
