There's no skb_pull performed when a mirred action is set at egress of a
mac device, with a target device/action that expects skb->data to point
at the network header.
As a result, either the target device is errornously given an skb with
data pointing to the mac (egress case), or the net stack receives the
skb with data pointing to the mac (ingress case).
E.g:
# tc qdisc add dev eth9 root handle 1: prio
# tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \
action mirred egress redirect dev tun0
(tun0 is a tun device. result: tun0 errornously gets the eth header
instead of the iph)
Revise the push/pull logic of tcf_mirred_act() to not rely on the
skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it
does not cover all "pull" cases.
Instead, calculate whether the required action on the target device
requires the data to point at the network header, and compare this to
whether skb->data points to network header - and make the push/pull
adjustments as necessary.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fq_classify() recycles a struct fq_flow because
a socket structure has been reallocated, we do not
set sk->sk_pacing_status immediately, but later if the
flow becomes detached.
This means that any flow requiring pacing (BBR, or SO_MAX_PACING_RATE)
might fallback to TCP internal pacing, which requires a per-socket
high resolution timer, and therefore more cpu cycles.
Fixes: 218af599fa ("tcp: internal implementation for pacing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
when users replace cls_u32 filters with new ones having wrong parameters,
so that u32_change() fails to validate them, the kernel doesn't roll-back
correctly, and leaves semi-configured rules.
Fix this in u32_walk(), avoiding a call to the walker function on filters
that don't have a match rule connected. The side effect is, these "empty"
filters are not even dumped when present; but that shouldn't be a problem
as long as we are restoring the original behaviour, where semi-configured
filters were not even added in the error path of u32_change().
Fixes: 6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
When a device is bound to a clsact qdisc, bind events are triggered to
registered drivers for both ingress and egress. However, if a driver
registers to such a device using the indirect block routines then it is
assumed that it is only interested in ingress offload and so only replays
ingress bind/unbind messages.
The NFP driver supports the offload of some egress filters when
registering to a block with qdisc of type clsact. However, on unregister,
if the block is still active, it will not receive an unbind egress
notification which can prevent proper cleanup of other registered
callbacks.
Modify the indirect block callback command in TC to send messages of
ingress and/or egress bind depending on the qdisc in use. NFP currently
supports egress offload for TC flower offload so the changes are only
added to TC.
Fixes: 4d12ba4278 ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.
When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.
Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.
Fixes: 4d12ba4278 ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user runs a command like
tc qdisc add dev eth1 root mqprio
KASAN stack-out-of-bounds warning is emitted.
Currently, NLA_ALIGN macro used in mqprio_dump provides too large
buffer size as argument for nla_put and memcpy down the call stack.
The flow looks like this:
1. nla_put expects exact object size as an argument;
2. Later it provides this size to memcpy;
3. To calculate correct padding for SKB, nla_put applies NLA_ALIGN
macro itself.
Therefore, NLA_ALIGN should not be applied to the nla_put parameter.
Otherwise it will lead to out-of-bounds memory access in memcpy.
Fixes: 4e8b86c062 ("mqprio: Introduce new hardware offload mode and shaper in mqprio")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_mpls_push was not updating ethertype of an ethernet packet if
the packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to
port 7 is an l3 device (ARPHRD_NONE) the skb_mpls_push function does
not update the ethertype of the packet even though the previous
push_eth action had added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x0800),ipv4(tos=0/0xfc,ttl=64,frag=no),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
push_mpls(label=13,tc=0,ttl=64,bos=1,eth_type=0x8847),4
Fixes: 8822e270d6 ("net: core: move push MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The act_ct TC module shares a common conntrack and NAT infrastructure
exposed via netfilter. It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision. Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress. The act_ct action doesn't have such capability.
Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit 5c72299fba ("net: sched: cls_flower: Classify
packets using port ranges") had added filtering based on port ranges
to tc flower. However the commit missed necessary changes in hw-offload
code, so the feature gave rise to generating incorrect offloaded flow
keys in NIC.
One more detailed example is below:
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 100-200 action drop
With the setup above, an exact match filter with dst_port == 0 will be
installed in NIC by hw-offload. IOW, the NIC will have a rule which is
equivalent to the following one.
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 0 action drop
The behavior was caused by the flow dissector which extracts packet
data into the flow key in the tc flower. More specifically, regardless
of exact match or specified port ranges, fl_init_dissector() set the
FLOW_DISSECTOR_KEY_PORTS flag in struct flow_dissector to extract port
numbers from skb in skb_flow_dissect() called by fl_classify(). Note
that device drivers received the same struct flow_dissector object as
used in skb_flow_dissect(). Thus, offloaded drivers could not identify
which of these is used because the FLOW_DISSECTOR_KEY_PORTS flag was
set to struct flow_dissector in either case.
This patch adds the new FLOW_DISSECTOR_KEY_PORTS_RANGE flag and the new
tp_range field in struct fl_flow_key to recognize which filters are applied
to offloaded drivers. At this point, when filters based on port ranges
passed to drivers, drivers return the EOPNOTSUPP error because they do
not support the feature (the newly created FLOW_DISSECTOR_KEY_PORTS_RANGE
flag).
Fixes: 5c72299fba ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sch->q.len hasn't been set if the subqueue is a NOLOCK qdisc
in mq_dump() and mqprio_dump().
Fixes: ce679e8df7 ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_mpls_pop was not updating ethertype of an ethernet packet if the
packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to port 7
is an l3 device (ARPHRD_NONE) the skb_mpls_pop function does not update
the ethertype of the packet even though the previous push_eth action had
added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x8847),
mpls(label=12/0xfffff,tc=0/0,ttl=0/0x0,bos=1/1),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
pop_mpls(eth_type=0x800),4
Fixes: ed246cee09 ("net: core: move pop MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field has never been checked since introduction in mainline kernel
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Fixes: 2db6dc2662 "sch_cake: Make gso-splitting configurable from userspace"
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a classful qdisc's child qdisc has set the flag
TCQ_F_CPUSTATS (pfifo_fast for example), the child qdisc's
cpu_bstats should be passed to gnet_stats_copy_basic(),
but many classful qdisc didn't do that. As a result,
`tc -s class show dev DEV` always return 0 for bytes and
packets in this case.
Pass the child qdisc's cpu_bstats to gnet_stats_copy_basic()
to fix this issue.
The qstats also has this problem, but it has been fixed
in 5dd431b6b9 ("net: sched: introduce and use qstats read...")
and bstats still remains buggy.
Fixes: 22e0f8b932 ("net: sched: make bstats per cpu and estimator RCU safe")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:
- Dynamic tick (nohz) updates, perhaps most notably changes to force
the tick on when needed due to lengthy in-kernel execution on CPUs
on which RCU is waiting.
- Linux-kernel memory consistency model updates.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Documentation updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
security/safesetid: Replace rcu_swap_protected() with rcu_replace_pointer()
net/sched: Replace rcu_swap_protected() with rcu_replace_pointer()
net/netfilter: Replace rcu_swap_protected() with rcu_replace_pointer()
net/core: Replace rcu_swap_protected() with rcu_replace_pointer()
bpf/cgroup: Replace rcu_swap_protected() with rcu_replace_pointer()
fs/afs: Replace rcu_swap_protected() with rcu_replace_pointer()
drivers/scsi: Replace rcu_swap_protected() with rcu_replace_pointer()
drm/i915: Replace rcu_swap_protected() with rcu_replace_pointer()
x86/kvm/pmu: Replace rcu_swap_protected() with rcu_replace_pointer()
rcu: Upgrade rcu_swap_protected() to rcu_replace_pointer()
rcu: Suppress levelspread uninitialized messages
rcu: Fix uninitialized variable in nocb_gp_wait()
rcu: Update descriptions for rcu_future_grace_period tracepoint
rcu: Update descriptions for rcu_nocb_wake tracepoint
rcu: Remove obsolete descriptions for rcu_barrier tracepoint
rcu: Ensure that ->rcu_urgent_qs is set before resched IPI
workqueue: Convert for_each_wq to use built-in list check
rcu: Several rcu_segcblist functions can be static
rcu: Remove unused function hlist_bl_del_init_rcu()
Documentation: Rename rcu_node_context_switch() to rcu_note_context_switch()
...
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
ct_policy and mpls_policy are parsed with nla_parse_nested(), which
does NL_VALIDATE_STRICT validation, strict_start_type is not needed
to set as it is actually trying to make some attributes parsed with
NL_VALIDATE_STRICT.
This patch is to remove it, and do the same on rtm_nh_policy which
is parsed by nlmsg_parse().
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allow matching options in erspan.
The options can be described in the form:
VER:INDEX:DIR:HWID/VER:INDEX_MASK:DIR_MASK:HWID_MASK.
When ver is set to 1, index will be applied while dir
and hwid will be ignored, and when ver is set to 2,
dir and hwid will be used while index will be ignored.
Different from geneve, only one option can be set. And
also, geneve options, vxlan options or erspan options
can't be set at the same time.
# ip link add name erspan1 type erspan external
# tc qdisc add dev erspan1 ingress
# tc filter add dev erspan1 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
erspan_opts 1:12:0:0/1:ffff:0:0 \
ip_proto udp \
action mirred egress redirect dev eth0
v1->v2:
- improve some err msgs of extack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allow matching gbp option in vxlan.
The options can be described in the form GBP/GBP_MASK,
where GBP is represented as a 32bit hexadecimal value.
Different from geneve, only one option can be set. And
also, geneve options and vxlan options can't be set at
the same time.
# ip link add name vxlan0 type vxlan dstport 0 external
# tc qdisc add dev vxlan0 ingress
# tc filter add dev vxlan0 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
vxlan_opts 01020304/ffffffff \
ip_proto udp \
action mirred egress redirect dev eth0
v1->v2:
- add .strict_start_type for enc_opts_policy as Jakub noticed.
- use Duplicate instead of Wrong in err msg for extack as Jakub
suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allow setting erspan options using the
act_tunnel_key action. Different from geneve options,
only one option can be set. And also, geneve options,
vxlan options or erspan options can't be set at the
same time.
Options are expressed as ver:index:dir:hwid, when ver
is set to 1, index will be applied while dir and hwid
will be ignored, and when ver is set to 2, dir and
hwid will be used while index will be ignored.
# ip link add name erspan1 type erspan external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
erspan_opts 1:2:0:0 \
action mirred egress redirect dev erspan1
v1->v2:
- do the validation when dst is not yet allocated as Jakub suggested.
- use Duplicate instead of Wrong in err msg for extack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allow setting vxlan options using the
act_tunnel_key action. Different from geneve options,
only one option can be set. And also, geneve options
and vxlan options can't be set at the same time.
gbp is the only param for vxlan options:
# ip link add name vxlan0 type vxlan dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
vxlan_opts 01020304 \
action mirred egress redirect dev vxlan0
v1->v2:
- add .strict_start_type for enc_opts_policy as Jakub noticed.
- use Duplicate instead of Wrong in err msg for extack as Jakub
suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8033 suggests an alternative approach to calculate the queue
delay in PIE by using a timestamp on every enqueued packet. This
patch adds an implementation of that approach and sets it as the
default method to calculate queue delay. The previous method (based
on Little's law) to calculate queue delay is set as optional.
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Acked-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The taprio qdisc allows to set mqprio setting but only once. In case
if mqprio settings are provided next time the error is returned as
it's not allowed to change traffic class mapping in-flignt and that
is normal. But if configuration is absolutely the same - no need to
return error. It allows to provide same command couple times,
changing only base time for instance, or changing only scheds maps,
but leaving mqprio setting w/o modification. It more corresponds the
message: "Changing the traffic mapping of a running schedule is not
supported", so reject mqprio if it's really changed.
Also corrected TC_BITMASK + 1 for consistency, as proposed.
Fixes: a3d43c0d56 ("taprio: Add support adding an admin schedule")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
info->options_len is 'u8' type, and when opts_len with a value >
IP_TUNNEL_OPTS_MAX, 'info->options_len = opts_len' will cast int
to u8 and set a wrong value to info->options_len.
Kernel crashed in my test when doing:
# opts="0102:80:00800022"
# for i in {1..99}; do opts="$opts,0102:80:00800022"; done
# ip link add name geneve0 type geneve dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 ip_proto udp action tunnel_key \
set src_ip 10.0.99.192 dst_ip 10.0.99.193 \
dst_port 6081 id 11 geneve_opts $opts \
action mirred egress redirect dev geneve0
So we should do the similar check as cls_flower does, return error
when opts_len > IP_TUNNEL_OPTS_MAX in tunnel_key_copy_opts().
Fixes: 0ed5269f9e ("net/sched: add tunnel option support to act_tunnel_key")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after commit 4097e9d250 ("net: sched: don't use tc_action->order during
action dump"), 'act->order' is initialized but then it's no more read, so
we can just remove this member of struct tc_action.
CC: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_max_ack_backlog can be read without any lock being held
at least in TCP/DCCP cases.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_ack_backlog can be read without any lock being held.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the kernel uses 64bit packet counters in scheduler layer,
we want to export these counters to user space.
Instead risking breaking user space by adding fields
to struct gnet_stats_basic, add a new TCA_STATS_PKT64.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this change, qdisc packet counter is no longer
a 32bit quantity. We still export 32bit values to user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new filter is added to cls_api, the function
tcf_chain_tp_insert_unique() looks up the protocol/priority/chain to
determine if the tcf_proto is duplicated in the chain's hashtable. It then
creates a new entry or continues with an existing one. In cls_flower, this
allows the function fl_ht_insert_unque to determine if a filter is a
duplicate and reject appropriately, meaning that the duplicate will not be
passed to drivers via the offload hooks. However, when a tcf_proto is
destroyed it is removed from its chain before a hardware remove hook is
hit. This can lead to a race whereby the driver has not received the
remove message but duplicate flows can be accepted. This, in turn, can
lead to the offload driver receiving incorrect duplicate flows and out of
order add/delete messages.
Prevent duplicates by utilising an approach suggested by Vlad Buslov. A
hash table per block stores each unique chain/protocol/prio being
destroyed. This entry is only removed when the full destroy (and hardware
offload) has completed. If a new flow is being added with the same
identiers as a tc_proto being detroyed, then the add request is replayed
until the destroy is complete.
Fixes: 8b64678e0a ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code which recognizes ICMP error packets is duplicated several
times. Use the icmp_is_err() and icmpv6_is_err() helpers instead, which
do the same thing.
ip_multipath_l3_keys() and tcf_nat_act() didn't check for all the error types,
assume that they should instead.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't swap oper and admin schedules too early, it's not correct and
causes crash.
Steps to reproduce:
1)
tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 1@2 \
base-time $SOME_BASE_TIME \
sched-entry S 01 80000 \
sched-entry S 02 15000 \
sched-entry S 04 40000 \
flags 2
2)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 90000 \
sched-entry S 02 20000 \
sched-entry S 04 40000 \
flags 2
3)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 150000 \
sched-entry S 02 200000 \
sched-entry S 04 40000 \
flags 2
Do 2 3 2 .. steps more times if not happens and observe:
[ 305.832319] Unable to handle kernel write to read-only memory at
virtual address ffff0000087ce7f0
[ 305.910887] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
[ 305.919306] Hardware name: Texas Instruments AM654 Base Board (DT)
[...]
[ 306.017119] x1 : ffff800848031d88 x0 : ffff800848031d80
[ 306.022422] Call trace:
[ 306.024866] taprio_free_sched_cb+0x4c/0x98
[ 306.029040] rcu_process_callbacks+0x25c/0x410
[ 306.033476] __do_softirq+0x10c/0x208
[ 306.037132] irq_exit+0xb8/0xc8
[ 306.040267] __handle_domain_irq+0x64/0xb8
[ 306.044352] gic_handle_irq+0x7c/0x178
[ 306.048092] el1_irq+0xb0/0x128
[ 306.051227] arch_cpu_idle+0x10/0x18
[ 306.054795] do_idle+0x120/0x138
[ 306.058015] cpu_startup_entry+0x20/0x28
[ 306.061931] rest_init+0xcc/0xd8
[ 306.065154] start_kernel+0x3bc/0x3e4
[ 306.068810] Code: f2fbd5b7 f2fbd5b6 d503201f f9400422 (f9000662)
[ 306.074900] ---[ end trace 96c8e2284a9d9d6e ]---
[ 306.079507] Kernel panic - not syncing: Fatal exception in interrupt
[ 306.085847] SMP: stopping secondary CPUs
[ 306.089765] Kernel Offset: disabled
Try to explain one of the possible crash cases:
The "real" admin list is assigned when admin_sched is set to
new_admin, it happens after "swap", that assigns to oper_sched NULL.
Thus if call qdisc show it can crash.
Farther, next second time, when sched list is updated, the admin_sched
is not NULL and becomes the oper_sched, previous oper_sched was NULL so
just skipped. But then admin_sched is assigned new_admin, but schedules
to free previous assigned admin_sched (that already became oper_sched).
Farther, next third time, when sched list is updated,
while one more swap, oper_sched is not null, but it was happy to be
freed already (while prev. admin update), so while try to free
oper_sched the kernel panic happens at taprio_free_sched_cb().
So, move the "swap emulation" where it should be according to function
comment from code.
Fixes: 9c66d15646 ("taprio: Add support for hardware offloading")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4011921137 ("net: sched: refactor block offloads counter
usage") missed the fact that either new prog or old prog may be
NULL.
Fixes: 4011921137 ("net: sched: refactor block offloads counter usage")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull RCU and LKMM changes from Paul E. McKenney:
- Documentation updates.
- Miscellaneous fixes.
- Dynamic tick (nohz) updates, perhaps most notably changes to
force the tick on when needed due to lengthy in-kernel execution
on CPUs on which RCU is waiting.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Linux-kernel memory consistency model updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Extend struct tc_action with new "tcfa_flags" field. Set the field in
tcf_idr_create() function and provide new helper
tcf_idr_create_from_flags() that derives 'cpustats' boolean from flags
value. Update individual hardware-offloaded actions init() to pass their
"flags" argument to new helper in order to skip percpu stats allocation
when user requested it through flags.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend TCA_ACT space with nla_bitfield32 flags. Add
TCA_ACT_FLAGS_NO_PERCPU_STATS as the only allowed flag. Parse the flags in
tcf_action_init_1() and pass resulting value as additional argument to
a_o->init().
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify stats update helper functions introduced in previous patches in this
series to fallback to regular tc_action->tcfa_{b|q}stats if cpu stats are
not allocated for the action argument. If regular non-percpu allocated
counters are in use, then obtain action tcfa_lock while modifying them.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit introduced helper function for updating qstats and
refactored set of actions to use the helpers, instead of modifying qstats
directly. However, one of the affected action exposes its qstats to
skb_tc_reinsert(), which then modifies it.
Refactor skb_tc_reinsert() to return integer error code and don't increment
overlimit qstats in case of error, and use the returned error code in
tcf_mirred_act() to manually increment the overlimit counter with new
helper function.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract common code that increments cpu_qstats counters into standalone act
API functions. Change hardware offloaded actions that use percpu counter
allocation to use the new functions instead of accessing cpu_qstats
directly.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract common code that increments cpu_bstats counter into standalone act
API function. Change hardware offloaded actions that use percpu counter
allocation to use the new function instead of incrementing cpu_bstats
directly.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all implementations of tc_action_ops->stats_update() callback
have almost exactly the same implementation of counters update
code (besides gact which also updates drop counter). In order to simplify
support for using both percpu-allocated and regular action counters
depending on run-time flag in following patches, extract action counters
update code into standalone function in act API.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces the use of rcu_swap_protected() with the more
intuitively appealing rcu_replace_pointer() as a step towards removing
rcu_swap_protected().
Link: https://lore.kernel.org/lkml/CAHk-=wiAsJLw1egFEE=Z7-GGtM6wcvtyytXZA1+BHqta4gg6Hw@mail.gmail.com/
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
[ paulmck: From rcu_replace() to rcu_replace_pointer() per Ingo Molnar. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
There is networking hardware that isn't based on Ethernet for layers 1 and 2.
For example CAN.
CAN is a multi-master serial bus standard for connecting Electronic Control
Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes
of payload. Frame corruption is detected by a CRC. However frame loss due to
corruption is possible, but a quite unusual phenomenon.
While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of
legacy protocols on top of CAN, which are not build with flow control or high
CAN frame drop rates in mind.
When using fq_codel, as soon as the queue reaches a certain delay based length,
skbs from the head of the queue are silently dropped. Silently meaning that the
user space using a send() or similar syscall doesn't get an error. However
TCP's flow control algorithm will detect dropped packages and adjust the
bandwidth accordingly.
When using fq_codel and sending raw frames over CAN, which is the common use
case, the user space thinks the package has been sent without problems, because
send() returned without an error. pfifo_fast will drop skbs, if the queue
length exceeds the maximum. But with this scheduler the skbs at the tail are
dropped, an error (-ENOBUFS) is propagated to user space. So that the user
space can slow down the package generation.
On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH
during compile time, or set default during runtime with sysctl
net.core.default_qdisc (see [1]), we get a bad user experience. In my test case
with pfifo_fast, I can transfer thousands of million CAN frames without a frame
drop. On the other hand with fq_codel there is more then one lost CAN frame per
thousand frames.
As pointed out fq_codel is not suited for CAN hardware, so this patch changes
attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices.
During transition of a netdev from down to up state the default queuing
discipline is attached by attach_default_qdiscs() with the help of
attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to
attach the pfifo_fast (pfifo_fast_ops) if the network device type is
"ARPHRD_CAN".
[1] https://github.com/systemd/systemd/issues/9194
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is networking hardware that isn't based on Ethernet for layers 1 and 2.
For example CAN.
CAN is a multi-master serial bus standard for connecting Electronic Control
Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes
of payload. Frame corruption is detected by a CRC. However frame loss due to
corruption is possible, but a quite unusual phenomenon.
While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of
legacy protocols on top of CAN, which are not build with flow control or high
CAN frame drop rates in mind.
When using fq_codel, as soon as the queue reaches a certain delay based length,
skbs from the head of the queue are silently dropped. Silently meaning that the
user space using a send() or similar syscall doesn't get an error. However
TCP's flow control algorithm will detect dropped packages and adjust the
bandwidth accordingly.
When using fq_codel and sending raw frames over CAN, which is the common use
case, the user space thinks the package has been sent without problems, because
send() returned without an error. pfifo_fast will drop skbs, if the queue
length exceeds the maximum. But with this scheduler the skbs at the tail are
dropped, an error (-ENOBUFS) is propagated to user space. So that the user
space can slow down the package generation.
On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH
during compile time, or set default during runtime with sysctl
net.core.default_qdisc (see [1]), we get a bad user experience. In my test case
with pfifo_fast, I can transfer thousands of million CAN frames without a frame
drop. On the other hand with fq_codel there is more then one lost CAN frame per
thousand frames.
As pointed out fq_codel is not suited for CAN hardware, so this patch changes
attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices.
During transition of a netdev from down to up state the default queuing
discipline is attached by attach_default_qdiscs() with the help of
attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to
attach the pfifo_fast (pfifo_fast_ops) if the network device type is
"ARPHRD_CAN".
[1] https://github.com/systemd/systemd/issues/9194
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
