Some PHY related fixes:
1. Fix Serdes WoL.
2. Fix loopback test on 10/100 only devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to a different ASF heartbeat message code to improve
reliability.
There were some reports of unintended resets on real time kernels
where the timer may be slow and cause the heartbeat to be late.
Netpoll will also have the same problem because the timer irq will
be unavailable.
Using the new heartbeat code, the ASF firmware will also check the
ring condition before resetting the chip when the heartbeat is
expiring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve 5704S autoneg logic by using a serdes_counter field to keep
track of the transient states. This eliminates a 200 msec busy
loop in the code. Autoneg will take its course without the driver
busy waiting for it to finish.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian. Annotated them and variables that are inferred to be
net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net devices should depend on NETDEVICES, so revert part of
Paolo's previous patch.
See http://marc.theaimsgroup.com/?l=linux-kernel&m=115566326218740&w=2
for history.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A driver shouldn't compare to DMA_ERROR_CODE directly, use
pci_dma_mapping_error() instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use hardware support for chained receive to break up large frames
into multiple pages. This avoids having to do a mult-page allocation
that can fail on a busy system due to fragmented memory.
For normal size MTU, this code behaves the same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netdevice transmit lock via netif_tx_lock rather than putting
lock in device specific code and using lockless transmit. The code is
cleaner using netif_tx_lock, and the performance is same.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since a transmit can take several control blocks, the old code waited
until the last control block was marked as done. This code processes
the return values incrementally. This makes slots in the tx ring available
and less chance of getting stuck.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the ethernet device name when requesting the irq because the
irqbalance daemon looks for the name when deciding policy.
Better to play along with this dubious heuristic.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Workarounds for 88e806x chips from the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the standard pci capability mechanism to access PCI express error
registers, rather than hard coding the offset. Mask off the PCI express
error from ever occuring on non-PCI express systems.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Look at the registers correctly, when doing gigabit full duplex.
Need to look for link partner result.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
[PATCH] bonding: update version number
[PATCH] git-netdev-all: pc300_tty build fix
[PATCH] Make PC300 WAN driver compile again
[PATCH] Modularize generic HDLC
[PATCH] more s2io __iomem annotations
[PATCH] restore __iomem annotations in e1000
[PATCH] 64bit bugs in s2io
[PATCH] bonding: Fix primary selection error at enslavement time
[PATCH] bonding: Don't mangle LACPDUs
[PATCH] bonding: Validate probe replies in ARP monitor
[PATCH] bonding: Don't release slaves when master is admin down
[PATCH] bonding: Add priv_flag to avoid event mishandling
[PATCH] bonding: Handle large hard_header_len
[PATCH] bonding: Remove unneeded NULL test
[PATCH] bonding: Format fix in seq_printf call
[PATCH] bonding: Convert delay value from s16 to int
[PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Delete unused drivers/net/gt64240eth.h
[PATCH] skge: fiber support
[PATCH] fix possible NULL ptr deref in forcedeth
...
I neglected to properly update the version number in the recent
patch series; this sets it to something reasonable.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In file included from drivers/net/wan/pc300_tty.c:59:
drivers/net/wan/pc300.h:335: error: field 'pppdev' has incomplete type
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We experimented with more descriptor buffer writebacks and found that
values larger than 8 give HW problems, but 8 is safe and gives us some
improved performance.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Memory allocated for new tx_ring and rx_ring leaks if
e1000_setup_XX_resources() fails.c Also this patch reduces stack usage
(removed tx_new and rx_new) and uses kzalloc instead kmalloc+memset(0)
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several minor issues exist in the low-level device handling code of
e1000. The NVM and EEPROM writing/reading code was updated which fixes
unneeded delays, adds proper eeprom aqcuiring steps and handle shadow
ram and flash access. Minor cosmetic adjustments to the polarity code
adding symbols. PHY reset code mistakenly distinguished between MAC
types instead of PHY types, and was fixes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We were plagued by our interrupt handler posting a watchdog event which
could occur when our adapter was going down in case a late packet arrived
just before e1000_down() finished. This caused the watchdog timer to start
after the NIC was down and keep rescheduling it every N seconds. Once
the driver unloaded it would panic.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Manageability is using one more RAR entry than we anticipated earlier
for ICH8.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add code to display the detected PCI-E bus width.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
When powering down the PHY (if WoL is disabled) we should only check
copper PHY's and handle PCI-E adapters differently.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several hardware bits were set all over the driver and have been
consolidated into a single function.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Disable jumbo frames for 82573L alltogether and when ASPM is enabled
since the hardware has problems with it. For the NICs that do support
this in the 82573 series we set ERT_2048 to attempt to receive as much
traffic as early as we can.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several manageability capability detection parts hinted towards
our code being incomplete for PCI-E. According to spec, we do not
want to poke any MANC bits at all.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
With a patch, ethtool can now signify the driver to advertise more
than just a single speed/duplex setting. This allows you to tell the
card to advertise in 10/100 in any speed if you don't have a gigabit
switch for instance.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add 4 multicast and broadcast hardware counters (rx/tx), and eliminate
as many non-hardware counters as possible.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Unify our shutdown/suspend/resume code and make it similar to e1000:
e1000_shutdown now calls suspend which does the exact same thing on
shutdown except saving PCI config state on suspend. WoL setup code
is now also more simple and works even when CONFIG_PM is not set, which
was previously broken.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We keep getting requests from people that think that this might be
an exploitable hole where we would overwrite 4 bytes in the netdev
struct if the pci name would exceed 15 characters. In reality this
will never happen but we fix it anyway.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This update to the copyright header adds the mailinglist, and aligns it
with the kernel licensing as well as remove the offending 'all rights
reserved'.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add modalias attribute support for the almost forgotten now EISA bus and
(at least some) EISA-aware modules.
The modalias entry looks like (for an 3c509 NIC):
eisa:sTCM5093
and the in-module alias like:
eisa:sTCM5093*
The patch moves struct eisa_device_id declaration from include/linux/eisa.h
to include/linux/mod_devicetable.h (so that the former now #includes the
latter), adds proper MODULE_DEVICE_TABLE(eisa, ...) statements for all
drivers with EISA IDs I found (some drivers already have that DEVICE_TABLE
declared), and adds recognision of __mod_eisa_device_table to
scripts/mod/file2alias.c so that proper modules.alias will be generated.
There's no support for /lib/modules/$kver/modules.eisamap, as it's not used
by any existing tools, and because with in-kernel modalias mechanism those
maps are obsolete anyway.
The rationale for this patch is:
a) to make EISA bus to act as other busses with modalias
support, to unify driver loading
b) to foget about EISA finally - with this patch, kernel
(who still supports EISA) will be the only one who knows
how to choose the necessary drivers for this bus ;)
[akpm@osdl.org: fix the kbuild bit]
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-the-net-bits-by: Jeff Garzik <jeff@garzik.org>
Acked-the-tulip-bit-by: Valerie Henson <val_henson@linux.intel.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes accesses to the HDLC-internal data structures
from pc300 driver, thus enabling it to compile but breaking part
of its functionality.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch enables building of individual WAN protocol support
routines (parts of generic HDLC) as separate modules.
All protocol-private definitions are moved from hdlc.h file
to protocol drivers. User-space interface and interface
between generic HDLC and underlying low-level HDLC drivers
are unchanged.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At enslavement time, the primary slave might not be activated if
there is already an active slave and the new slave is the primary.
Replaced complicated logic with a call to bond_select_active_slave(),
which does the right thing.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6378
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed handling of 802.3ad LACPDUs. Do not byte swap data in
place in the packet. Updated nomenclature of "__ntohs_lacpdu" to be
"htons"; it was previously used for both ntohs and htons operations, but
only called ntohs functions.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.
The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When a bonding netdevice is admin-ed down it loses the slaves
attributes (set via ifenslave). This is not consistent with other
behavior of netdevices (example a qdisc attached to a netdevice doesnt
disappear or an attached IP address etc).
The included patch fixes this. Ive tested by ifenslaving, downing the
bond, checking /proc and making sure it still has the slaves, up-ing the
bond and making sure things continue to work.
Jay/Bonding folks if you are ok with it, just ACK it or include it in
your tree etc. Otherwise we can discuss.
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add priv_flag to specifically identify bonding-involved devices. Needed
because IFF_MASTER is an unreliable identifier (vlan interfaces above bonding
will inherit IFF_MASTER). Misidentification of devices would cause
notifier events for other devices to be erroneously processed by bonding,
causing various havoc.
Bug discovered by Martin Papik <martin.papik@ipsec.info>; this patch is
modified from his original.
Signed-off-by: Martin Papik <martin.papik@ipsec.info>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The bonding driver fails to adjust its hard_header_len when enslaving
interfaces. Whenever an interface with a hard_header_len greater than the
ETH_HLEN default is enslaved, the potential for an oops exists, and if the
oops happens while responding to an arp request, for example, the system
panics. GIANFAR devices may use an extended hard_header for VLAN or
hardware checksumming. Enslaving such a device and then transmitting over
it causes a kernel panic.
Patch modified from submitter's original, but submitter agreed with this
patch in private email.
Signed-off-by: Mark Huth <mhuth@mvista.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded test for NULL. Reported by Thomas Dillig
<tdillig@stanford.edu> and Isil Dillig <isil@stanford.edu> via Stephen
Hemminger <shemminger@osdl.org>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Though link_failure_count is type unsigned int, this value is outputted to
/proc/net/bonding/bondX file using "%d" instead of "%u".
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The value of "downdelay/miimon" and "updelay/miimon" are stored in
slave->delay. The type of downdelay, updelay, and miimon are all int.
However, slave->delay is type short, and it is not possible to store the
value of "downdelay/miimon" or "updelay/miimon" in some cases. (For example,
miimon=1 downdelay=32768)
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow channel bonding to enslave a 10 Gig adapter without errors.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for older fiber versions of the SysKonnect board. These chipsets
use an internal PHY so they require special handling. The older sk98lin
driver already supported these
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There seems to be a possible NULL pointer deref bug in
drivers/net/forcedeth.c::nv_loopback_test(). If dev_alloc_skb() fails, the
next line will call skb_put() with a NULL first argument which it'll then
try to deref - kaboom: a NULL pointer deref. Found by coverity (#1337).
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While checking gcc 4.1 -Wextra warnings, I stumbled across the following
two warnings:
drivers/net/phy/phy_device.c:528: warning: comparison of unsigned expression < 0 is always false
drivers/net/phy/phy_device.c:546: warning: comparison of unsigned expression < 0 is always false
Since phy_read() returns an integer and can return negative values, it seems
to me the best way to get proper error handling working again is to make val
an int. Currently it is an u32, so the < 0 check always fails.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixes section mismatch warnings when built as a module.
Also, mark find_ledma and sun4 init function as __devinit
too.
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup for running long periodic work has a bug that leads to
netdev watchdog tx timeouts. This change eliminates the timeouts.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch includes a big cleanup of the existing unused LED code,
and adds support for controlling the LED.
The link LED will blink if the device is not associated. The LED
switches between 2 seconds on and 1 second off. If the device is
associated the LED is switched on.
The link LED also indicates packet TX. I do a little bit more led
resetting than the vendor driver, but the device works now as
expected for single LED and double LED devices.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For housekeeping and watchdog tasks a workqueue is created. The
central workqueue is not used to prevent crashes creates by bugs.
It might be changed, when the housekeeping is stabilized.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Checking whether a mutex is not locked directly before
mutex_lock() is called, doesn't make sense. The whole point of
mutex_lock() is to block, if the mutex is locked.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Caused by the fact that physical control registers appear to have
only a width of 16 bit, 32-bit writes are not required.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error message is changed to a printk as the original dprintk
would be optimized away if debugging were not enabled. If the error
is triggered, a more meaningful message is returned.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In bcm43xx-softmac, the bcm43xx_stats struct contains a variable that
is no longer used. In addition, two TODO entries related to noise
processing in bcm43xx_rx have been completed, and as unused one
is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the PHY initialization code for bcm43xx-softmac
to conform with recent changes in the clean-room specs at
http://bcm-specs.sipsolutions.net. Mostly, these changes implement
the sequence needed for chips with GPHY revision 8; however, the
patch also corrects a typo in one address, and some parts that were
missing from the spec when the initial coding was done.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch to make bcm43xx-softmac be compatible with the revised SSID
length of WE-21.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ql3xxx_probe() does ioremap and stores result in ->mem_map_registers.
On failure exit it does iounmap() of the same thing.
OTOH, ql3xxx_remove() does iounmap() of ->mmap_virt_base which is
(a) never assigned and
(b) never used other than in that iounmap() call.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Add the ethtool -S (show statistics) feature to the Spidernet ethernet
driver. I have tested it extensively and believe it is ready to be
applied.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code for the EV96100 evaluation board hasn't compiled since at least
November 15, 2003, so it is being deleted as of 2.6.18 due to lack of
a user base.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No 64-bit PPC_MULTIPLATFORM platforms use the mv643xx_eth driver,
so build it only on PPC32.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Sven Luther <sl@bplan-gmbh.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Cirrus Logic ep93xx is an ARM SoC that includes an ethernet MAC
-- this patch adds a driver for that ethernet MAC.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the pci_device_ids to PCI_DEVICE() macro. Saves 1.5k in the
sourcefile.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several IR drivers used "for (i = 0; i < 4; i++)" to walk their
dev_self[] table. Better to use ARRAY_SIZE(). And fix ali-ircc so it
won't run off the end if we find too many adapters.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace CHECKSUM_HW by CHECKSUM_PARTIAL (for outgoing packets, whose
checksum still needs to be completed) and CHECKSUM_COMPLETE (for
incoming packets, device supplied full checksum).
Patch originally from Herbert Xu, updated by myself for 2.6.18-rc3.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (64 commits)
[BLOCK] dm-crypt: trivial comment improvements
[CRYPTO] api: Deprecate crypto_digest_* and crypto_alg_available
[CRYPTO] padlock: Convert padlock-sha to use crypto_hash
[CRYPTO] users: Use crypto_comp and crypto_has_*
[CRYPTO] api: Add crypto_comp and crypto_has_*
[CRYPTO] users: Use crypto_hash interface instead of crypto_digest
[SCSI] iscsi: Use crypto_hash interface instead of crypto_digest
[CRYPTO] digest: Remove old HMAC implementation
[CRYPTO] doc: Update documentation for hash and me
[SCTP]: Use HMAC template and hash interface
[IPSEC]: Use HMAC template and hash interface
[CRYPTO] tcrypt: Use HMAC template and hash interface
[CRYPTO] hmac: Add crypto template implementation
[CRYPTO] digest: Added user API for new hash type
[CRYPTO] api: Mark parts of cipher interface as deprecated
[PATCH] scatterlist: Add const to sg_set_buf/sg_init_one pointer argument
[CRYPTO] drivers: Remove obsolete block cipher operations
[CRYPTO] users: Use block ciphers where applicable
[SUNRPC] GSS: Use block ciphers where applicable
[IPSEC] ESP: Use block ciphers where applicable
...
The fs_no mean used to be fs_enet driver driven, hence it was an
enumeration across all the possible fs_enet "users" in the SoC. Now, with
QE on the pipeline, and to make DTS descriptions more clear, fs_no features
relevant SoC part number, with additional field to describe the SoC type.
Another reason for that is now not only fs_enet is going to utilize those
stuff. There might be UART, HLDC, and even USB, so to prevent confusion and
be ready for upcoming OF_device transfer, fs_enet and cpm_uart drivers were
updated in that concern, as well as the relevant DTS.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Incorporating the new way of cpm2 immr access, introduced in the previous
patch, into CPM2 peripheral devices (fs_enet and cpm_uart). Both ppc and
powerpc approved working( real actions taken in powerpc only, ppc just
has a wrapper to keep init stuff consistent).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
The last minute fix submitted by the author fixed a bug, but
broke the driver build.
Noticed by Al Viro, since I can't build on said platform.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts all remaining users to use the new block cipher type
where applicable. It also changes all simple cipher operations to use
the new encrypt_one/decrypt_one interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On powerpc and ppc, insl_ns and insl are identical as are outsl_ns and
outsl, so remove the conditional use of insl_ns and outsl_ns.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi Jeff,
sorry to bother you again. We figured out that the readq function we
included in the eHEA patch we sent yesterday to access eHEA registers
is defined as little endian on POWER. This collides with our adapter.
We talked to some PPC people who told us there is a discussion going
on about new access functions. We were told to use __raw_readq /
__raw_writeq for now.
This patch fixes this bug found by our internal tests today.
Please apply this small patch on the latest patch we sent you yesterday.
If it is easier for you I can also give you the entire eHEA patch again.
sorry and thanks a lot,
Jan-Bernd
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
drivers/net/ehea/ehea.h | 2 +-
drivers/net/ehea/ehea_hw.h | 11 ++++++++---
2 files changed, 9 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A recent patch in -mm3 titled
"gregkh-pci-pci-don-t-enable-device-if-already-enabled.patch" causes
pci_enable_device() to be a no-op if the kernel thinks that the device is
already enabled. This change breaks the PCI error recovery mechanism in
the e1000 device driver, since, after PCI slot reset, the card is no longer
enabled. This is a trivial fix for this problem. Tested.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix support for big endian platforms like PPC.
Still not sure about VLAN acceleration (does it need swapping)?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the support for fiber connected gigabit boards.
Allow half duplex gigabit to be configured.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems with transmit pause frames. The driver was telling the
GMAC to flush (not process) pause frames. Manually disabling pause wasn't
working because of problems in the setup.
This maybe the cause of the lockup under load.
http://bugzilla.kernel.org/show_bug.cgi?id=6839
Patch against netdev-2.6 git tree
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement NAPI changes to pcnet32 driver. Compile default is off.
Listed as experimental.
Len and Don both worked on a NAPI implementation and have both tested
these changes.
An e1000 blasting short packets to the pcnet32 will lockup Don's system
until the receive storm stops. Without NAPI Len's system watchdog would
expire causing the system to reboot. With NAPI the system will stay
operational.
Tested ia32 and ppc64. Tested '970A, '971, '972, '973, '975, '976, and
'978.
The Kconfig changes came from Len. Don is to blame for all the others.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Breaking the receive frame processing into two routines for greater clarity.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the receive routine and create the transmit routine.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change some magic numbers to clearer names. A few whitespace changes.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Delete unnecessary save/restore of rap in interrupt handler and statistics.
tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a missing call to dma_unmap_single() in the receive path. Without
this call, errors have been observed on non-cache-coherent systems.
Signed-off-by Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The commit 'e1000: Remove 0x1000 as supported device' (Jeff Kirsher,
673a052fde) Removes PIC device ID 8086:1000
from the list of supported devices. A fix was submitted for the original
issue (commit 6a9516989f).
This commit reverts commit 673a052fde and
re-enables 82542rev3 chips completely.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As long as the descriptor fits on a single cacheline, the change
should be almost free.
Now ring_info is not used at all. Remove it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Commit 581d708eb4 (oct. 5 2005) introduced
partial Multiqueue support for e1000 which broke macro smartness in setting
up head/tail registers for 82542 rev3 chipsets, making these adapters
completely non-working since 2.6.15.
This commit sets the proper head and tail registers for read and write
descriptor rings. Ths fix was tested on an 82542 rev3 NIC and newer NICs.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As I promised last week, here is the first pass at removing all
unnecessary printk's that exist in network device drivers currently in
promiscuous mode. The duplicate messages are not needed so they have
been removed. Some of these drivers are quite old and might not need an
update, but I did them all anyway.
I am currently auditing the remaining conditional printk's and will send
out a patch for those soon.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hostap_cs driver
- added support for Proxim Harmony PCI W-Lan Card (uses pd6729 based
pcmcia2pci bridge)
Signed-off-by: Christian Steineck <memphis@machzwo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coverity CID 1160 & 1161
Remove some dead code from bcm43xx_sysfs.c in 2.6.18-rc6
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prints out the ucode debug status to sysfs. So, users can
watch the microcode status of their hardware.
Signed-off-by: Martin Langer <martin-langer@gmx.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prints microcode revision, patchlevel, date and time to
KERN_INFO. Also, version 4.xx microcodes (rev>0x128) will be rejected
by the driver, because they still do not work.
Signed-off-by: Martin Langer <martin-langer@gmx.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes code that was make obsolete when the wireless
statistics in bcm43xx-softmac were changed, but was overlooked at that
time. The value of bcm->stats.link_quality computed here is never used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds bitrate information to the scan result in the Prism54
driver, like some/most other driver do.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inspired by an e-mail by Stephen Hemminger I decided to remove all
unneeded packed attributes from the code where the member variables are
already aligned. This avoids horrible code being generated on some
architectures.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Vincent TOUCHARD
zd1211 chip 0b05:170c v4802 high 00-11-d8 AL2230_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Martin Dummer.
zd1211 chip 0b3b:5630 v4330 high 00-01-e3 RF2959_RF pa0 ---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an out of sequence step in the bcm43xx_init_board
routine for bcm43xx-softmac.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes various bugs in the init and shutdown code
that would lead to lockups and crashes.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Caused by a documentation issue I mixed up fields of the zd_status
structure. This patch fixes it and improves also the average
computation, which is now using only measurements of packets sent
by the access point.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inverting the write ordering of the TxDescAddr{High/Low} registers
suffices to trigger a sabbat of PCI errors which make the device
completely dysfunctional. The issue has not been reported on a
different platform.
Switching from MMIO accesses to I/O ones as done in Realtek's
own driver fixes (papers over ?) the bug as well but I am not
thrilled to see everyone pay the I/O price for an obscure bug.
This is the minimal change to handle the issue.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
dm9000_release_board calls release_resource with the platform resource
instead of the requested resource:
db->addr_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
db->addr_req = request_mem_region(db->addr_res->start, i, pdev->name);
dm9000_release_board:
if (db->addr_res != NULL) {
release_resource(db->addr_res);
kfree(db->addr_req);
With this behavior the kernel will crash on the second removal. The
attached patch fix this problem.
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This removes unnecessary messages that show up every time I put my
ethernet card in promiscuous mode. I'm already getting notification
from the networking layer, I don't need notification from the driver as
well.
There are probably other drivers that do this as well -- I'll look
around and see what I can find.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Include "tulip.h" in winbond-840.c and clean up lots of redundant
definitions.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update/cleanup some definitions in tulip.h and tulip_core.c.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move tulip_select_media() processing to a workqueue, instead of
delaying in interrupt context, edited by Kyle McMartin to use kevent
thread, instead of creating its own workqueue.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The obvious safe registers to read is one from PCI config space.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As the cookie returned by pci_iomap() is fairly useless...
[Compile warning on pci_resource_start() format fixed up by Valerie
Henson.]
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the needlessly global e1000_phy_igp_get_info() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Because of the NAPI and other SMP fixes, let's call
this a version.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver has much better performance if transmit done is handled in
NAPI softirq. Change from doing transmit locking in driver (LLTX) and
use device lock.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver needs to access the IRQ status inside of lock to avoid
races with other places changing IRQ mask etc. This may be related
to some of the SMP bugs reported against skge in kernel bugzilla.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change to use new netdev_alloc_skb interface for 2.6.18.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some more Marvell device id's, these are from the latest SysKonnect
vendor driver version of sk98lin (8.36).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve the firmware selection by adding 2 cases where we should use the
optimized firmware:
* when the actual PCIe link width is lower than 8x.
* when the board is plugged to one of the new Intel PCIe chipsets that
are known to provide aligned PCIe completions.
The patch actually raises two concerns:
* We might want to add a generic PCI function to get the PCIe link width since
some other drivers (at least ipath) do the same. But we probably do not want
to add a new function for every PCIe capability. I will probably look at it
and discuss it on linux-pci in the future.
* As requested during the submission, the PCI ids of chipsets that are known to
provided aligned completion are defined in the myri10ge code. If we keep adding
new ones, it might become better to move them to pciids.h.
But, this sort of quirk to detect these chipsets are very specific to our NIC,
I don't think it is worth moving it to the PCI core until somebody else really
needs it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the firmware download URL in Kconfig to match the header
in drivers/net/myri10ge/myri10ge.c.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch decouples the dependency between the rx checksum feature and
vlan feature. This is done by ignoring the checksum information if the
user has disabled rx checksum when vlan is enabled.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses an errata found on certain marvell phys concerning
the reset of the BMCR phy register during phy reset.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
