Provide support for the fan capability registers for the next generation
systems of types MQM87xx, MSN34xx, MSN37xx. These new registers provide
configuration for tachometers and fan drawers connectivity. Use these
registers for next generation led, fan and hotplug structures in order
to distinguish between the systems which have minor configuration
differences. This reduces the amount of code used to describe such
systems.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Notify user when hotplug device signal is received in order to allow user
to handle such case, if it wishes to take some action on this matter.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Simplify the logic of ASIC health discovery.
ASIC device can indicate its health state as a good, booting or dormant.
During ASIC reset the device is dropped to dormant state and should get to
the stable good health state through the intermediate booting state.
The sequence for getting to the steady state health after reset is:
(dormant -> booting -> good)+.
Initial implementation assumes that ?good? within this sequence is always
repeated twice and device is getting steady state only after the second
?good?. This patch removes this dependency, since the second ?good? is
received because of the noise on line and can be ignored. Device reaches
steady state after the first ?good? is received.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
As already done treewide, switch from open-coded multiplication to using
2-factor allocation helpers.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Introduce new Mellanox platform driver to allow access to Mellanox
programmable device register space trough sysfs interface.
The driver purpose is to provide sysfs interface for user space for the
registers essential for system control and monitoring.
The sets of registers for sysfs access are supposed to be defined per
system type bases and include the registers related to system resets
operation, system reset causes monitoring and some kinds of mux selection.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: Kconfig typo fixes spotted by Randy Dunlap]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Several incremental improvements including new keycodes, new models, new
quirks, and related documentation. Adds LED platform driver activation
for Mellanox systems. Some minor optimizations and cleanups. Includes
several bug fixes, message silencing, mostly minor.
The following commits were previously merged during the 4.17 RC cycle:
- 06b8b00b33 platform/x86: asus-wireless: Fix NULL pointer dereference
- 6ed66c3ce0 platform/x86: Kconfig: Fix dell-laptop dependency chain.
- 74783c99bf platform/x86: DELL_WMI use depends on instead of select for DELL_SMBIOS
- cf48bf9eee platform/x86: asus-wmi: Fix NULL pointer dereference
The following is an automated git shortlog grouped by driver:
acer-wmi:
- add another KEY_POWER keycode
apple-gmux:
- fix gmux_get_client_id()'s return type
asus-laptop:
- Simplify getting .drvdata
asus-wireless:
- Fix format specifier
dell-laptop:
- Fix keyboard backlight timeout on XPS 13 9370
dell-smbios:
- Match on www.dell.com in OEM strings too
dell-wmi:
- Ignore new rfkill and fn-lock events
- Set correct keycode for Fn + left arrow
fujitsu-laptop:
- Simplify soft key handling
ideapad-laptop:
- Add E42-80 to no_hw_rfkill
- Add fn-lock setting
- Add MIIX 720-12IKB to no_hw_rfkill
lib/string_helpers:
- Add missed declaration of struct task_struct
intel_scu_ipc:
- Replace mdelay with usleep_range in intel_scu_ipc_i2c_cntrl
mlx-platform:
- Add LED platform driver activation
platform/mellanox:
- Add new ODM system types to mlx-platform
- mlxreg-hotplug: add extra cycle for hotplug work queue
- mlxreg-hotplug: Document fixes for hotplug private data
platform_data/mlxreg:
- Document fixes for hotplug device
silead_dmi:
- Add entry for Chuwi Hi8 tablet touchscreen
- Add touchscreen info for the Onda V891w tablet
- Add info for the PoV mobii TAB-P800W (v2.0)
- Add touchscreen info for the Jumper EZpad 6 Pro
thinkpad_acpi:
- silence false-positive-prone pr_warn
- do not report thermal sensor state for tablet mode switch
- silence HKEY 0x6032, 0x60f0, 0x6030
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbIFzqAAoJEKbMaAwKp3644JcIAJ8iBMobacNWjIJvPJ8ytwLE
NUP7/W/8NUXkwnxXzURorlnoO6Uj4+54c+QfO+HQV/+Y46fJaX9x2tWRtcEkpJU3
L6c59kYAMlu5rN5ekCcQex4FKL8Pd7q6QpF8KZtP8gw2ujUEeGA1m/qcTmUlkOQF
AFfbSFJtmMOinbL5ufkaW7Gu91EVFhuvgIoK/XdOhwAbyYAPEbtttKlUjkZGx6GU
iJbpimcmdtfXBqMzvpOHw/4EUXLwgDVr1F8PdGmvEHyK45SHIZcK936Ihiq+CjVA
USFKZhMMYU4sifI77pIP9Trftm+FdaLnPumGVj836OMp1+k10YBy1hDIGwI6i68=
=+O74
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.18-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Several incremental improvements including new keycodes, new models,
new quirks, and related documentation. Adds LED platform driver
activation for Mellanox systems. Some minor optimizations and
cleanups. Includes several bug fixes, message silencing, mostly minor
Automated summary:
acer-wmi:
- add another KEY_POWER keycode
apple-gmux:
- fix gmux_get_client_id()'s return type
asus-laptop:
- Simplify getting .drvdata
asus-wireless:
- Fix format specifier
dell-laptop:
- Fix keyboard backlight timeout on XPS 13 9370
dell-smbios:
- Match on www.dell.com in OEM strings too
dell-wmi:
- Ignore new rfkill and fn-lock events
- Set correct keycode for Fn + left arrow
fujitsu-laptop:
- Simplify soft key handling
ideapad-laptop:
- Add E42-80 to no_hw_rfkill
- Add fn-lock setting
- Add MIIX 720-12IKB to no_hw_rfkill
lib/string_helpers:
- Add missed declaration of struct task_struct
intel_scu_ipc:
- Replace mdelay with usleep_range in intel_scu_ipc_i2c_cntrl
mlx-platform:
- Add LED platform driver activation
platform/mellanox:
- Add new ODM system types to mlx-platform
- mlxreg-hotplug: add extra cycle for hotplug work queue
- mlxreg-hotplug: Document fixes for hotplug private data
platform_data/mlxreg:
- Document fixes for hotplug device
silead_dmi:
- Add entry for Chuwi Hi8 tablet touchscreen
- Add touchscreen info for the Onda V891w tablet
- Add info for the PoV mobii TAB-P800W (v2.0)
- Add touchscreen info for the Jumper EZpad 6 Pro
thinkpad_acpi:
- silence false-positive-prone pr_warn
- do not report thermal sensor state for tablet mode switch
- silence HKEY 0x6032, 0x60f0, 0x6030"
* tag 'platform-drivers-x86-v4.18-1' of git://git.infradead.org/linux-platform-drivers-x86: (30 commits)
platform/x86: silead_dmi: Add entry for Chuwi Hi8 tablet touchscreen
platform/x86: dell-laptop: Fix keyboard backlight timeout on XPS 13 9370
platform/x86: dell-wmi: Ignore new rfkill and fn-lock events
platform/x86: mlx-platform: Add LED platform driver activation
platform/mellanox: Add new ODM system types to mlx-platform
platform/mellanox: mlxreg-hotplug: add extra cycle for hotplug work queue
platform/x86: ideapad-laptop: Add E42-80 to no_hw_rfkill
platform/x86: silead_dmi: Add touchscreen info for the Onda V891w tablet
platform/x86: silead_dmi: Add info for the PoV mobii TAB-P800W (v2.0)
platform/x86: silead_dmi: Add touchscreen info for the Jumper EZpad 6 Pro
platform/x86: asus-wireless: Fix format specifier
platform/x86: asus-wmi: Fix NULL pointer dereference
platform/x86: dell-wmi: Set correct keycode for Fn + left arrow
platform/x86: acer-wmi: add another KEY_POWER keycode
platform/x86: ideapad-laptop: Add fn-lock setting
platform/x86: ideapad-laptop: Add MIIX 720-12IKB to no_hw_rfkill
lib/string_helpers: Add missed declaration of struct task_struct
platform/x86: DELL_WMI use depends on instead of select for DELL_SMBIOS
platform/mellanox: mlxreg-hotplug: Document fixes for hotplug private data
platform_data/mlxreg: Document fixes for hotplug device
...
Add extra cycle for hotplug work queue to handle the case when a signal is
It adds missed logic for signal acknowledge, by adding an extra run for
received, but no specific signal assertion is detected. Such case
theoretically can happen for example in case several units are removed or
inserted at the same time. In this situation acknowledge for some signal
can be missed at signal top aggreagation status level. The extra run will
allow to handler to acknowledge the missed signal.
The interrupt handling flow performs the next steps:
(1)
Enter mlxreg_hotplug_work_handler due to signal assertion.
Aggregation status register is changed for example from 0xff to 0xfd
(event signal group related to bit 1).
(2)
Mask aggregation interrupts, read aggregation status register and save it
(0xfd) in aggr_cache, then traverse down to handle signal from groups
related to the changed bit.
(3)
Read and mask group related signal.
Acknowledge and unmask group related signal (acknowledge should clear
aggregation status register from 0xfd back to 0xff).
(4)
Re-schedule work queue for the immediate execution.
(5)
Enter mlxreg_hotplug_work_handler due to re-scheduling.
Aggregation status is changed from previous 0xfd to 0xff.
Go over steps (2) - (5) and in case no new signal assertion
is detected - unmask aggregation interrupts.
The possible race could happen in case new signal from the same group is
asserted after step (3) and prior step (5). In such case aggregation
status will change back from 0xff to 0xfd and the value read from the
aggregation status register will be the same as a value saved in
aggr_cache. As a result the handler will not traverse down and signal
will stay unhandled.
Example of faulty flow:
The signal routing flow is as following (f.e. for of FANi removing):
- FAN status and event registers related bit is changed;
-- intermediate aggregation status register is changed;
--- top aggregation status register is changed;
---- interrupt routed to CPU and interrupt handler is invoked.
When interrupt handler is invoked it follows the next simple logic (f.e
FAN3 is removed):
(a1) mask top aggregation interrupt mask register;
(a2) read top aggregation interrupt status register and test to which
underling group belongs a signal (FANs in this case and is changed
from 0xff to 0xfb and 0xfb is saved as a last status value);
(b1) mask FANs interrupt mask register;
(b2) read FANs status register and test which FAN has been changed
FAN3 in this example);
(c1) perform relevant action;
<--------------- (FAN2 is removed at this point)
(b3) clear FANs interrupt event register to acknowledge FAN3 signal;
(b4) unmask FANs interrupt mask register
(a3) unmask top aggregation interrupt mask register;
An interrupt handler is invoked, since FAN2 interrupt is not acknowledge.
It should set top aggregation interrupt status register bit 6 (0xfb).
In step (a2)
(a2) read top aggregation interrupt and comparing it with saved value
does not show change (same 0xfb) and after (a2) execution jumps to
(a3) and signal leaved unhandled
The fix will enforce handler to traverse down in case the signal is
received, but signal assertion is not detected.
Fixes: 304887041d ("platform/x86: Introduce support for Mellanox hotplug driver")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add missing description of dev, regmap, dwork_irq, after_probe in struct
mlxreg_hotplug_priv_data.
Remove dwork field from the structure mlxreg_hotplug_priv_data itself and
for the descriptions, since it is not used.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
mlx-platform does not provide a bus number to i2c-mlxcpld, assuming it
is always one. On some x86 systems, other i2c drivers may probe before
i2c-mlxcpld, causing bus one to be busy.
Make mlx-platform determine which adapter number is free prior to
activating i2c-mlxpld, adjusting the mux base numbers accordingly.
Update the mlxreg-hotplug pdata similarly.
This adds an explicit mlx-platform build dependency on I2C, update the
Kconfig accordingly. Add the missing REGMAP dependency while we're at
it.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: Rewrite commit message more concisely]
[dvhart: Add build dependencies]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Change the first input parameter in mlxreg_hotplug_device_create to the
pointer to mlxreg_hotplug private data in order to use the fields from
the private data structure.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: Cleaned up commit message]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
mlx-platform activates i2c-mux-reg, which creates buses needed by
mlxreg-hotplug. If the mlxreg-hotplug probe runs before the i2c-mux-reg
probe completes, it may attempt to connect a device to an adapter number
that has not been created yet, and fail.
Make mlx-platform driver record the highest bus number in mlxreg-hotplug
platform data and defer mlxreg-hotplug probe until all the buses are
created.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: rewrite commit message more concisely]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
With gcc-4.1.2:
drivers/platform/mellanox/mlxreg-hotplug.c: In function ‘mlxreg_hotplug_health_work_helper’:
drivers/platform/mellanox/mlxreg-hotplug.c:347: warning: ‘ret’ is used uninitialized in this function
Indeed, if mlxreg_core_item.count is zero, ret is used uninitialized.
While this is unlikely to happen (it is set to ARRAY_SIZE(...) in x86
board files), this is done in another source file, so fix this by
preinitializing ret to zero.
Fixes: c6acad68eb ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Verify before creation of hotplug device if the associated adapter number
is negative. It could be in case hotplug event is not associated with
hotplug device.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add ARM in addition to X86 as supported architectures in the Mellanox
Hotplug Platform driver Kconfig entry.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
[dvhart: rewrite commit message]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Restructure mlxreg header for unification of hotplug item definitions.
Unify hotplug items to allow any kind of item (power controller, fan
eeprom, psu eeprom, asic health) in common way.
Use a hardware independent regmap interface, enabling the support of
hotplug events over programmable devices attached to different bus
types, such as I2C, LPC, or SPI. Add a device node to the
mlxreg_core_data structure.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: spelling corrections, refactor device node introduction]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Move the mlxreg_hotplug_device_create and _destroy functions up with the
related attribute functions. No functional changes.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: refactored commit into smaller functional changes]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use Linux convention of nr instead of bus for i2c adapter number.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: refactored commit into smaller functional changes]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The driver does not make use of anything defined in wait.h.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: refactor into smaller functional changes, leave spinlock.h]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
In preparation for making the hotplug driver build for different
architectures, move mlxcpld-hotplug.c to platform/mellanox and the
header to include/linux/platform_data as mlxreg.h to reflect the new
interface changes to come.
Replace references to CPLD with REG throughout the files, consistent
with the new name.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: update copyright, rewrite commit message]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
