This is a port of commit 248de22e63 ("i40e/i40evf: Account for frags
split over multiple descriptors in check linearize")
As part of testing workloads (read/write) using larger IO size (128K)
tx_timeout is observed and whenever it happens, it was due to
tx_linearize.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently VFs are only allowed to get 16, 4, and 1 queue pair by
default, which require 17, 5, and 2 MSI-X vectors respectively. This
is because each VF needs a MSI-X per data queue and a MSI-X for its
other interrupt. The calculation is based on the number of VFs created,
MSI-X available, and queue pairs available at the time of VF creation.
Unfortunately the values above exclude 2 queue pairs when only 3 MSI-X
are available to each VF based on resource constraints. The current
calculation would default to 2 MSI-X and 1 queue pair. This is a waste
of resources, so fix this by allowing 2 queue pairs per VF when there
are between 2 and 5 MSI-X available per VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This fix has been added to address memory leak issues resulting from
triggering a sudden driver reset which does not allow us to follow our
normal removal flows for SW XLT entries for advanced features.
- Adding call to destroy flow profile locks when clearing SW XLT tables.
- Extraction sequence entries were not correctly cleared previously
which could cause ownership conflicts for repeated reset-replay calls.
Fixes: 31ad4e4ee1 ("ice: Allocate flow profile")
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Display and count some useful hot-path statistics. The usefulness is as
follows:
- tx_restart: use to determine if the transmit ring size is too small or
if the transmit interrupt rate is too low.
- rx_gro_dropped: use to count drops from GRO layer, which previously were
completely uncounted when occurring.
- tx_busy: use to determine when the driver is miscounting number of
descriptors needed for an skb.
- tx_timeout: as our other drivers, count the number of times we've reset
due to timeout because the kernel only prints a warning once per netdev.
Several of these were already counted but not displayed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The page reuse statistic wasn't even being displayed to the user, even
though the driver counted it. Don't waste the struct space and hot-path
cycles since the driver doesn't display it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replacing flow profile locks with RSS profile locks in the function to
remove all RSS rules for a given VSI. This is to align the locks used
for RSS rule addition to VSI and removal during VSI teardown to avoid
a race condition owing to several iterations of the above operations.
In function to get RSS rules for given VSI and protocol header replacing
the pointer reference of the RSS entry with a copy of hash value to
ensure thread safety.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
set_rss_lut can fail due to incorrect vsi_id mask. vsi_id is 10 bit
but mask was 0x1FF whereas it should be 0x3FF.
For vsi_num >= 512, FW set_rss_lut can fail with return code
EACCESS (VSI ownership issue) because software was providing
incorrect vsi_num (dropping 10th bit due to incorrect mask) for
set_rss_lut admin command
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The grst_delay variable in ice_check_reset contains the maximum time
(in 100 msec units) that the driver will wait for a reset event to
transition to the Device Active state. The value is the sum of three
separate components:
1) The maximum time it may take for the firmware to process its
outstanding command before handling the reset request.
2) The value in RSTCTL.GRSTDEL (the delay firmware inserts between first
seeing the driver reset request and the actual hardware assertion).
3) The maximum expected reset processing time in hardware.
Referring to this total time as "grst_delay" is misleading and
potentially confusing to someone checking the code and cross-referencing
the hardware specification.
Fix this by renaming the variable to "grst_timeout", which is more
descriptive of its actual use.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In certain configurations without power management support, the
following warnings happen:
drivers/net/ethernet/intel/ice/ice_main.c:4214:12: warning:
'ice_resume' defined but not used [-Wunused-function]
4214 | static int ice_resume(struct device *dev)
| ^~~~~~~~~~
drivers/net/ethernet/intel/ice/ice_main.c:4150:12: warning:
'ice_suspend' defined but not used [-Wunused-function]
4150 | static int ice_suspend(struct device *dev)
| ^~~~~~~~~~~
Mark these functions as __maybe_unused to make it clear to the
compiler that this is going to happen based on the configuration,
which is the standard for these types of functions.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Depending on PAGE_SIZE, the following unused parameter warning can be
reported:
drivers/net/ethernet/intel/ice/ice_txrx.c: In function ‘ice_rx_frame_truesize’:
drivers/net/ethernet/intel/ice/ice_txrx.c:513:21: warning: unused parameter ‘size’ [-Wunused-parameter]
unsigned int size)
The 'size' variable is used only when PAGE_SIZE >= 8192. Add __maybe_unused
to remove the warning.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
For the FW logging info AQ command, we currently set the ICE_AQ_FLAG_RD
in order to work around a FW issue. This issue has been fixed so remove the
workaround.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The scope of the macro local variable 'i' can be reduced. Do so to avoid
static analysis tools from complaining.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of ice_setup_pf_sw() a PF VSI is setup; release the VSI in case of
failure.
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the PF VSI's context parameters are left in a bad state when
going into safe mode. This is causing VLAN traffic to not pass. Fix this
by configuring the PF VSI to allow all VLAN tagged traffic.
Also, remove redundant comment explaining the safe mode flow in
ice_probe().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is a port of i40e commit 705639572e ("i40e: need_wakeup flag might
not be set for Tx").
Quoting the original commit message:
"The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an interrupt
since interrupts are disabled in the napi poll loop) between the time we
stopped processing the Tx completions and interrupts are enabled again.
In this case, the need_wakeup flag will have been cleared at the end of
the Tx completion processing as we believe we will get an interrupt from
the outstanding completion at a later point in time. But if this
completion interrupt occurs before interrupts are enable, we lose it and
should at that point really have set the need_wakeup flag since there
are no more outstanding completions that can generate an interrupt to
continue the processing. When this happens, user space will see a Tx
queue need_wakeup of 0 and skip issuing a syscall, which means will
never get into the Tx processing again and we have a deadlock."
As a result, packet processing stops. This patch introduces a fix for
this issue, by always setting the need_wakeup flag at the end of an
interrupt processing. This ensures that the deadlock will not happen.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Distribute the Tx queues evenly across all queue groups. This will
help the queues to get more equal sharing among the queues when all
are in use.
In the previous algorithm, the next queue group node will be picked up
only after the previous one filled with max children.
For example: if VSI is configured with 9 queues, the first 8 queues
will be assigned to queue group 1 and the 9th queue will be assigned to
queue group 2.
The 2 queue groups split the bandwidth between them equally (50:50).
The first queue group node will share the 50% bandwidth with all of
its children (8 queues). And the second queue group node will share
the entire 50% bandwidth with its only children.
The new algorithm will fix this issue.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
By default the queues are configured in legacy mode. The default
BW settings for legacy/advanced modes are different. The existing
code was using the advanced mode default value of 1 which was
incorrect. This caused the unbalanced BW sharing among siblings.
The recommended default value is applied.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask bits before accessing the profile type field.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a user sets the value of the TX or RX descriptors to some non-default
value using 'ethtool -G' then we need to not overwrite the values when
we rebuild the VSI. The VSI rebuild could happen as a result of a user
setting the number of queues via the 'ethtool -L' command. Fix this by
checking to see if the value we have stored is non-zero and if it is
then don't change the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return ICE_ERR_DOES_NOT_EXIST return code if admin command error code is
ICE_AQ_RC_ENOENT (not exist). ice_aq_sw_rules is used when switch
rule is getting added/deleted/updated. In case of delete/update
switch rule, admin command can return ICE_AQ_RC_ENOENT error code
if such rule does not exist, hence return ICE_ERR_DOES_NOT_EXIST error
code from ice_aq_sw_rule, so that caller of this function can decide
how to handle ICE_ERR_DOES_NOT_EXIST.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the driver experiences a link event (especially link up)
there can be multiple events generated. Some of these are
link fault and still have a state of DOWN set. The problem
happens when the link comes UP during the PF driver handling
one of the LINK DOWN events. The status of the link is updated
and is now seen as UP, so when the actual LINK UP event comes,
the port information has already been updated to be seen as UP,
even though none of the UP activities have been completed.
After the link information has been updated in the link
handler and evaluated for MEDIA PRESENT, if the state
of the link has been changed to UP, treat the DOWN event
as an UP event since the link is now UP.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.
The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.
This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.
The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Report AOC types as fiber instead of unknown.
Signed-off-by: Doug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.
This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.
As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.
The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.
Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.
Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.
The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.
The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.
This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.
Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the pre-C90-extension "C struct hack" method (using a single-
element array at the end of a structure for implementing variable-length
types) to the preferred use of C99 flexible array member.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are a number of structures that consist of a one-element array as the
only struct member. Some of those are unused so remove them. Others are
used to index into a buffer/array consisting of a variable number of a
different data or structure type. Those are unnecessary since we can use
simple pointer arithmetic or index directly into the buffer to access
individual elements of the buffer/array.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new devlink region used for capturing a snapshot of the device
capabilities buffer which is reported by the firmware over the AdminQ.
This information can useful in debugging driver and firmware
interactions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2020-06-25
This series contains updates to i40e driver and removes the individual
driver versions from all of the Intel wired LAN drivers.
Shiraz moves the client header so that it can easily be shared between
the i40e LAN driver and i40iw RDMA driver.
Jesse cleans up the unused defines, since they are just dead weight.
Alek reduces the unreasonably long wait time for a PF reset after reboot
by using jiffies to limit the maximum wait time for the PF reset to
succeed. Added additional logging to let the user know when the driver
transitions into recovery mode. Adds new device support for our 5 Gbps
NICs.
Todd adds a check to see if MFS is set after warm reboot and notifies
the user when MFS is set to anything lower than the default value.
Arkadiusz fixes a possible race condition, where were holding a
spin-lock while in atomic context.
v2: removed code comments that were no longer applicable in patch 2 of
the series. Also removed 'inline' from patch 4 and patch 8 of the
series. Also re-arranged code to be able to remove the forward
function declarations. Dropped patch 9 of the series, while the
author works on cleaning up the commit message.
v3: Updated patch 8 description to answer Jakub's questions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
The READ_ONCE macro is used when reading rings prior to accessing the
statistics pointer. The corresponding WRITE_ONCE usage when allocating and
freeing the rings to ensure protected access was not in place. Introduce
this.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
