Pre-DCE12 needs special treatment for BTR / low framerate
compensation for more stable behaviour:
According to comments in the code and some testing on DCE-8
and DCE-11, DCE-11 and earlier only apply VTOTAL_MIN/MAX
programming with a lag of one frame, so the special BTR hw
programming for intermediate fixed duration frames must be
done inside the current frame at flip submission in atomic
commit tail, ie. one vblank earlier, and the fixed refresh
intermediate frame mode must be also terminated one vblank
earlier on pre-DCE12 display engines.
To achieve proper termination on < DCE-12 shift the point
when the switch-back from fixed vblank duration to variable
vblank duration happens from the start of VBLANK (vblank irq,
as done on DCE-12+) to back-porch or end of VBLANK (handled
by vupdate irq handler). We must leave the switch-back code
inside VBLANK irq for DCE12+, as before.
Doing this, we get much better behaviour of BTR for up-sweeps,
ie. going from short to long frame durations (~high to low fps)
and for constant framerate flips, as tested on DCE-8 and
DCE-11. Behaviour is still not quite as good as on DCN-1
though.
On down-sweeps, going from long to short frame durations
(low fps to high fps) < DCE-12 is a little bit improved,
although by far not as much as for up-sweeps and constant
fps.
v2: Fix some wrong locking, as pointed out by Nicholas.
v3: Simplify if-condition in vupdate-irq - nit by Nicholas.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The comparison of inserted_frame_duration_in_us against a
duration calculated from max_refresh_in_uhz is both wrong
in its math and not needed, as the min_duration_in_us value
is already cached in in_out_vrr for reuse. No need to
recalculate it wrongly at each invocation.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RGB565 support isn't restricted to just the primary plane in DC, so
also expose support for it on overlays.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Originally we did the amdgpu_dm_handle_vrr_transition call before
interrupts were enabled. After the interrupt toggling logic was
moved around for support enabling CRTCs with no primary planes
active this was no longer being called in the case where there
wasn't a modeset.
This fixes failures in igt@kms_vrr@* with error
"Timed out: Waiting for vblank event".
[How]
Shift them back into the loop that always ran before interrupts were
enabled.
Pull out the logic that updated VRR state into the same loop since
there's no reason these need to be split.
In the case where we're going from VRR off, no planes to VRR on, some
active planes we'll still be covered for having the VRR vupdate
handler enabled - vblank will be re-enabled at this point, it will
see that VRR is active and set the vupdate interrupt on there.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Refactor dp vendor parsing int to a new function, and call it before
get_active_converter_info().
Also, add a flag to skip parsing of Display ID 2.0. Some devices fail on
readind DID2, but we shouldn't fail EDID read because of it. Add this
flag to facilitate the logic.
Signed-off-by: John Barberiz <John.Barberiz@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1.
In addition, future HW will need to access the HUBPREQ_DEBUG register
for hubp_init. Add it to the reg list.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new interface now replaces the old interface for all known
configurations.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the generic introduction of seamless boot, the display is no
longer blanked upon boot. However, this causes corruption on some
systems that does not lock the memory in the non-secure boot case,
resulting in brief corruption on boot due to garbage being written into
the frame buffer.
[How]
Add a flag, read during DC init, to determine whether display should be
blanked on boot. Default to true.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Replace certain register writes with register sets that overwrites the
the entire register, instead of only a field within the register.
* Add program_watermarks() entry to hubbub vtable. Hook it up to
existing functions that program watermarks.
* Add additional watermark registers.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many userspace applications (and IGT) seem to expect that most drivers
can keep a CRTC active and enabled if there are no primary or overlay
planes.
DC is setup to handle this but only in the case where there are
absolutely no planes on the CRTC - no primary, cursor, or overlay.
[How]
Add a check to reject commits that have cursor planes enabled and
nothing else on CRTCs since we can't handle that. The new helper
does_crtc_have_active_cursor is used for this.
In atomic commit tail, we need to let DC know that there are zero
planes enabled when doing stream updates to let it disable and blank
pipes as appropriate.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When disabling all the pipes for a CRTC the page-flip interrupt also
gets disabled on Raven. We can't re-enable the page-flip interrupt
unless we give DC at least one active DC plane.
We currently enable interrupts after the call to dc_commit_state since
there's currently no valid sequence that should disable all the planes
or re-enable planes for a CRTC without first going through
dc_commit_state.
If we were to allow for a CRTC to be enabled with no primary plane this
would not be the case - the call to dc_commit_updates_for_stream would
enable the planes when going from zero to at least one active plane,
but manage_dm_interrupts would have been called too early.
This results in a page-flip timeout on any subsequent commits since we
think the page-flip are now enabled when they're actually disabled.
We need to enable interrupts after the call to
dc_commit_updates_for_stream.
[How]
Split enabling interrupts into two passes. One pass before
dc_commit_updates_for_stream and one after it.
Shifting all the interrupts to be strictly below the call doesn't
currently work even though it should in theory. We end up queuing
off the vblank event to be handle by the flip handler before it's
actually enabled in some cases, particularly:
old_crtc_state->active = false -> new_crtc_state->active = true
The framebuffer states haven't changed and we can technically still
do a "pageflip" in this case and send back the event.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We only currently drop the vblank reference when the stream is
being removed from the context. We should be dropping it whenever we
disable interrupts and reaquiring it after we re-enable them.
We also never get the extra reference correctly when re-enabling
interrupts, since grabbing the reference has the following condition:
if (!crtc_state->crc_enabled && enable)
drm_crtc_vblank_get(crtc);
This means that crc_enabled must be *false* in order to grab the extra
reference.
[How]
Always drop the ref whenever we're disabling interrupts.
Only disable CRC capture when the stream is being removed.
Always grab the ref by setting dm_new_crtc_state->crc_enabled = false
before the call to re-enable CRC capture.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can't do cursor programming after the planes have been disabled
since there won't be any pipes - leading to lock warnings and the wrong
cursor state being left in the registers.
When we re-enable the planes after the previous cursor state will also
remain if we don't have a cursor plane.
[How]
If we're disabling the planes then do the cursor programming first.
If we're not disabling the planes then do the cursor programming after.
Introduce the amdgpu_dm_commit_cursors helper to avoid code duplication
for both of these cases.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The vblank and pageflip interrupts should only be enabled for a CRTC
that's enabled and has active planes.
The current logic takes care of this, but isn't setup to handle the case
where the active plane count goes to zero but the stream remains
enabled.
We currently block this case since we don't allow commits that enable a
CRTC with no active planes, but shouldn't be any reason we can't support
this from a hardware perspective and many userspace applications expect
to be able to do it (like IGT).
[How]
The count_crtc_active_planes function fills in the number of
"active_planes" on the dm_crtc_state. This should be the same as
DC's plane_count on the stream_status but easier to access since we
don't need to lock the private atomic state with the DC context.
Add the "interrupts_enabled" flag to the dm_crtc_state and set it based
on whether the stream exists and if there are active planes on the
stream.
Update the disable and enable logic to make use of this new flag.
There shouldn't be any functional change (yet) with this patch.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_sriov_vf would return 0x0 or 0x4 to indicate if sriov.
but F32_POLL_ENABLE need 0x0 or 0x1 to determine if enabled.
set 0x4 into F32_POLL_ENABLE would make SDMA0_GFX_RB_WPTR_POLL_CNTL not working.
Signed-off-by: Wentao Lou <Wentao.Lou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update Vega20 sdma golden settings.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] clock unit mis-match between caller DC and SMU interface.
dc pass lock in mhz. the same unit as smu. no covert is needed.
[HOW] remove covert_10k_to_mhz in smu interface
this fixes corruption issue with 4k @60 display and stutter
mode enable
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently an allocation is being made but the allocation failure
check is being performed on another pointer. Fix this by checking
the correct pointer. Also use the normal kernel idiom for null
pointer checks.
Addresses-Coverity: ("Resource leak")
Fixes: 43e3ac8389 ("drm/amd/display: Add function to copy DC streams")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When DMCU interrupts x86, it leads to undefined phy programming
[how]
expand dmcu interface to support new PHY lock and unlock commands
if DMCU FW doesn't support these commands, they fail silently so its okay
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting with DCN1, the input_pixel_processor (ipp) struct has been
replaced by dpp struct (part of DAL3.1 SW architecture change).
Need to update logic to handle cases where ipp is never allocated.
[How]
Only skip cursor position programming if both ipp and dpp resources
are NULL.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Power down of PHY on eDP requires us to call eDP power
control to power on again
[How]
1. In the case link rates don't match, disable PHY
requires calling of eDP power control ON after
2. Link disable case limit to eDP path since
this is not really applicable to DP since we do
power down PHY as part of verify link cap
3. Move detection of eDP link settings to be
done even for S4 resume cases where other
dpcd cap read and edid read can be skipped
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some DMCU messages were being sent in cases where
there was no DMCU FW at all, which resulted in some wait
timeouts
[How]
Delay sending some of the DMCU messages after FW
init is called and DMCU is running.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We'll need the ability to copy a dc_stream_state for some features.
Implement it here.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Workaround was missing in one HW disable path,
meaning when all pipes are power gated, stutter was
not working
[How]
Add workaround for init_hw path for stutter
workaround
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smu.ppt_funcs is only initialized for ASICs supporting SW SMU.
On a Hawaii ASIC, attempting to access the udev attribute
ATTRS{power_dpm_state} will cause a null pointer deref in
amdgpu_get_dpm_state() because of this.
Fix by checking if SW SMU is supported first.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They will be used by DC when runing ASIC-specific HUBP initialization.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Patch '5edb0c9b Fix deadlock with display during hanged ring recovery'
was accidentaly removed during one of DALs code merges.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't block others while waiting for the fences to finish, concurrent
submission is perfectly valid in this case and holding the lock can
prevent killed applications from terminating.
Signed-off-by: Christian König <ckoenig.leichtzumerken@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's normal for VRAM to lost during GPU reset and so change
the log level to INFO to avoid confusing users.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable UMDPSTATE support to force performance level for raven2.
v2: squash in warning fix (Alex)
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The power profile allows the user to adjust the power state
heuristics for clock level transitions.
v2: squash in warning fix (Alex)
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a pr_err message. Fix it.
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a DRM_INFO message. Fix it.
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under SRIOV, we need disable DRIVER_ATOMIC.
Otherwise, it will trigger WARN_ON at drm_universal_plane_init.
Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_bo_destroy had a bug by calling amdgpu_bo_unref outside mutex_lock.
If amdgpu_device_recover_vram executed between amdgpu_bo_unref and list_del_init,
it would get NULL of shadow->parent, then caused Call Trace and GPU reset failed.
Signed-off-by: Wentao Lou <Wentao.Lou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is needed by DC to support EDID emulation on USB-C ports.
CC: Samson Tam <Samson.Tam@amd.com>
CC: Harry Wentland <harry.wentland@amd.com>
CC: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Method of getting firmware version is the same across ASICs, so remove
them from ASIC-specific files and create one in amdgpu_amdkfd.c. This new
created get_fw_version simply reads fw_version from adev->gfx than parsing
the ucode header.
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Send message with parameter to SMC to set xgmi pstate
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC and DM already support DRM_FORMAT_RGB565, it's just missing from the
list of valid formats.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PSP SOS firmware needs to be 0x80067 or later.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used this change to investigate the performance of bandwidth validation,
it will be useful to have if we need to investigate further.
[How]
We use performance counter tick numbers to profile performance, they live
at dc->debug.bw_val_profile (set .enable in debugger to turn on measuring).
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a fast_validate parameter in dc_validate_global_state for future use
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
As long as we have at least one non-cursor plane enabled on a CRTC then
the CRTC itself can remain enabled.
This will allow for commits where there's an overlay plane enabled but
no primary plane enabled.
[How]
Remove existing primary plane fb != NULL checks and replace them with
the new does_crtc_have_active_plane helper.
This will be called from atomic check when validating the CRTC.
Since the primary plane state can now potentially be NULL we'll need
to guard for that when accessing it in some of the cursor logic.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Surface scaling info updates can affect bandwidth and blocks. We need
to be checking these with global validation to avoid underflow or
corruption.
[How]
Drop the state->allow_modeset early exit in
dm_determine_update_type_for_commit. Most of those should be considered
fast now anyway.
Fill in scaling info and it to the surface update in atomic
check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM thinks that the update type should be full whenever a stream or
plane is added or removed (including recreations).
This won't match in the case where DC thinks what looks like a fast
update to DM is actually a medium or full - like scaling changes that
affect bandwidth and clocks.
[How]
Drop this warning. DC knows better than the DM does for determining
cases like this.
The other warning can be kept for now since it would warn on a pretty
serious DC or DM bug.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC expects the surface memory address to identify the surface.
This doesn't work with what we're doing with the temporary surfaces,
it will always assume this is a full update because the surface
isn't in the current context.
[How]
Use the surface directly. This doesn't give us much improvement yet,
since we always create a new dc_plane_state when state->allow_modeset
is true.
The call into dc_check_update_surfaces_for_stream also needs to be
locked, for two reasons:
1. It checks the current DC state
2. It modifies the surface update flags
Both of which could be currently in the middle of commit work from
commit tail.
A TODO here is to pass the context explicitly into this function and
find a way to get the surface update flags out of it without modifying
the surface in place.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Planes have downscaling limits and upscaling limits per format and DM
is expected to validate these using DC caps. We should fail atomic
check validation if we aren't capable of doing the scaling.
[How]
We don't currently create store which DC plane maps to which DRM plane
so we can't easily check the caps directly. For now add basic
constraints that cover the absolute min and max downscale / upscale
limits for most RGB and YUV formats across ASICs.
Leave a TODO indicating that these should really be done with DC caps.
We'll probably need to subclass DRM planes again in order to correctly
identify which DC plane maps to it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM doesn't need to know which link cap is being retrieved ( verified
or preferred ). Let DC figure it out.
[How]
Change name.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
