For i945 and earlier chips, the backlight frequency value had the low
bit (of 16) fixed to zero. The Pineview code path handled this by just
exposing the backlight range as 15 bits while other chips had the
backlight range limited to 0 .. 0xfffe.
This patch makes everyone take the pineview code path, providing 15
bits of backlight duty cycle range which seems more than sufficient to
me.
Daniel Mack reported that writing 1 to bit 0 of the duty cycle
register was causing problems on his Samsung X20 notebook, even when
the duty cycle value was less than the maximum backlight value. (He
tried a value of 29749 with max_brightness of 29750). This patch never
writes a '1' to that bit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reported-and-tested-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org
The Ivybridge eDP control register looks like a cross between a
Cougarpoint PCH DP control register and a Sandybridge eDP control
register.
Where things trivially match, share the code. Where there are any
tricky bits, just split things out into two obviously separate code paths.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Fang Xun <xunx.fang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41991
On IVB C0+ with newer BIOSes, the forcewake handshake has changed. There's
now a bitfield for different driver components to keep the GT powered
on. On Linux, we centralize forcewake handling in one place, so we
still just need a single bit, but we need to use the new registers if MT
forcewake is enabled.
This needs testing on affected machines. Please reply with your
tested-by if you had problems after a BIOS upgrade and this patch fixes
them.
v2: force MT mode. shift by 16
v3: set MT force wake bits then check ECOBUS
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42923
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm: integer overflow in drm_mode_dirtyfb_ioctl()
drivers/gpu/vga/vgaarb.c: add missing kfree
drm/radeon/kms/atom: unify i2c gpio table handling
drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
ttm: Don't return the bo reserved on error path
drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
...
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.
Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain
With above expr, number of voltages that can be selected is
step value count * gain count
constant for gain count will be called VDD1_2_NUM_VOLT_COARSE
existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning
drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Last piece of code using ANY_I2C_BUS was deleted almost 2 years ago,
so ANY_I2C_BUS can go away as well.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
The wrong bits were put on the wire, fix that.
This fixes kernel bug #42562.
Signed-off-by: Sheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a potential integer overflow in drm_mode_dirtyfb_ioctl()
if userspace passes in a large num_clips. The call to kmalloc would
allocate a small buffer, and the call to fb->funcs->dirty may result
in a memory corruption.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit dc93728084.
As requested by Ben Herrenschmidt:
"This breaks some powerpc platforms at least. The practice of having
a node provide an explicit "interrupt-parent" property pointing to
itself is an old trick that we've used in the past to allow a
device-node to have interrupts routed to different controllers.
In that case, the node also contains an interrupt-map, so the node is
its own parent, the interrupt resolution hits the map, which then can
route each individual interrupt to a different parent."
Grant says:
"Ah, nuts, yes that is broken then. Yes, please revert the commit and
Rob & I will come up with a better solution.
Rob, I think it can be done by explicitly checking for np ==
desc->interrupt_parent in of_irq_init() instead of relying on
of_irq_find_parent() returning NULL."
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mount_subtree() pointless use-after-free
iio: fix a leak due to improper use of anon_inode_getfd()
microblaze: bury asm/namei.h
kbuf is a buffer that is local to this function, so all of the error paths
leaving the function should release it.
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Split the quirks and i2c_rec assignment into separate
functions used by both radeon_lookup_i2c_gpio() and
radeon_atombios_i2c_init(). This avoids duplicating code
and cases where quirks were only added to one of the
functions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes i2c test failures when i2c_algo_bit.bit_test=1.
The hw doesn't actually require a mask, so just set it
to the default mask bits for r1xx-r4xx radeon ddc.
I missed this part the first time through.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
An unlikely race could case a bo to be returned reserved on an error path.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux: (25 commits)
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
drm/i915: enable cacheable objects on Ivybridge
drm/i915: add constants to size fence arrays and fields
drm/i915: Ivybridge still has fences!
drm/i915: forcewake warning fixes in debugfs
drm/i915: Fix object refcount leak on mmappable size limit error path.
drm/i915: Use mode_config.mutex in ironlake_panel_vdd_work
...
d'oh... we'd carefully pinned mnt->mnt_sb down, dropped mnt and attempt
to grab s_umount on mnt->mnt_sb. The trouble is, *mnt might've been
overwritten by now...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Revert pnfs ugliness from the generic NFS read code path
SUNRPC: destroy freshly allocated transport in case of sockaddr init error
NFS: Fix a regression in the referral code
nfs: move nfs_file_operations declaration to bottom of file.c (try #2)
nfs: when attempting to open a directory, fall back on normal lookup (try #5)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: remove free-space-cache.c WARN during log replay
Btrfs: sectorsize align offsets in fiemap
Btrfs: clear pages dirty for io and set them extent mapped
Btrfs: wait on caching if we're loading the free space cache
Btrfs: prefix resize related printks with btrfs:
btrfs: fix stat blocks accounting
Btrfs: avoid unnecessary bitmap search for cluster setup
Btrfs: fix to search one more bitmap for cluster setup
btrfs: mirror_num should be int, not u64
btrfs: Fix up 32/64-bit compatibility for new ioctls
Btrfs: fix barrier flushes
Btrfs: fix tree corruption after multi-thread snapshots and inode_cache flush
* 'writeback-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: remove vm_dirties and task->dirties
writeback: hard throttle 1000+ dd on a slow USB stick
mm: Make task in balance_dirty_pages() killable
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: fix more ET131X build errors
staging: et131x depends on NET
staging: slicoss depends on NET
linux-next: et131x: Fix build error when CONFIG_PM_SLEEP not enabled
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (48 commits)
USB: Fix Corruption issue in USB ftdi driver ftdi_sio.c
USB: option: add PID of Huawei E173s 3G modem
OHCI: final fix for NVIDIA problems (I hope)
USB: option: release new PID for ZTE 3G modem
usb: Netlogic: Fix HC_LENGTH call in ehci-xls.c
USB: storage: ene_ub6250: fix compile warnings
USB: option: add id for 3G dongle Model VT1000 of Viettel
USB: serial: pl2303: rm duplicate id
USB: pch_udc: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
USB: pch_udc: Support new device LAPIS Semiconductor ML7831 IOH
usb-storage: Accept 8020i-protocol commands longer than 12 bytes
USB: quirks: adding more quirky webcams to avoid squeaky audio
powerpc/usb: fix type cast for address of ioremap to compatible with 64-bit
USB: at91: at91-ohci: fix set/get power
USB: cdc-acm: Fix disconnect() vs close() race
USB: add quirk for Logitech C600 web cam
USB: EHCI: fix HUB TT scheduling issue with iso transfer
USB: XHCI: resume root hubs when the controller resumes
USB: workaround for bug in old version of GCC
USB: ark3116 initialisation fix
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: ldisc, wait for ldisc infinitely in hangup
TTY: ldisc, move wait idle to caller
TTY: ldisc, allow waiting for ldisc arbitrarily long
Revert "tty/serial: Prevent drop of DCD on suspend for Tegra UARTs"
RS485: fix inconsistencies in the meaning of some variables
pch_uart: Fix DMA resource leak issue
serial,mfd: Fix CMSPAR setup
tty/serial: Prevent drop of DCD on suspend for Tegra UARTs
pch_uart: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_uart: Support new device LAPIS Semiconductor ML7831 IOH
pch_uart: Fix hw-flow control issue
tty: hvc_dcc: Fix duplicate character inputs
jsm: Change maintainership
* 'char-misc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: ad525x_dpot: Fix AD8400 spi transfer size.
pch_phub: Fix MAC address writing issue for LAPIS ML7831
pch_phub: Improve ADE(Address Decode Enable) control
pch_phub: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_phub: Support new device LAPIS Semiconductor ML7831 IOH
pcie-gadget-spear: Add "platform:" prefix for platform modalias
MAINTAINERS: add CHAR and MISC driver maintainers
altroot support has been gone for years, along with arch/*/asm/namei.h;
looks like a dummy survivor that sat it out in microblaze tree...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'dev' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix up a undefined error in ext4_free_blocks in debugging code
ext4: add blk_finish_plug in error case of writepages.
ext4: Remove kernel_lock annotations
ext4: ignore journalled data options on remount if fs has no journal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: Allocate larger oid buffer in request msgs
ceph: initialize root dentry
ceph: fix iput race when queueing inode work
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Log the fact that we've given ELOOP rather than creating a loop
minixfs: kill manual hweight(), simplify
fs/minix: Verify bitmap block counts before mounting
The log replay code only partially loads block groups, since
the block group caching code is able to detect and deal with
extents the logging code has pinned down.
While the logging code is pinning down block groups, there is
a bogus WARN_ON we're hitting if the code wasn't able to find
an extent in the cache. This commit removes the warning because
it can happen any time there isn't a valid free space cache
for that block group.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
sbi is not defined, so let ext4_free_blocks use EXT4_SB(sb) instead
when EXT4FS_DEBUG is defined.
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
To prevent an NFS server from being used to create a directory loop in an NFS
superblock on the client, the following patch was committed:
commit 1836750115
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Tue Jul 12 21:42:24 2011 -0400
Subject: fix loop checks in d_materialise_unique()
This causes ELOOP to be reported to anyone trying to access the dentry that
would otherwise cause the kernel to complete the loop.
However, no indication is given to the caller as to why an operation that ought
to work doesn't. The fault is with the kernel, which doesn't want to try and
solve the problem as it gets horrendously messy if there's another mountpoint
somewhere in the trees being spliced that can't be moved[*].
[*] The real problem is that we don't handle the excision of a subtree that
gets moved _out_ of what we can see. This can happen on the server where a
directory is merely moved between two other dirs on the same filesystem, but
where destination dir is not accessible by the client.
So, given the choice to return ELOOP rather than trying to reconfigure the
dentry tree, we should give the caller some indication of why they aren't being
allowed to make what should be a legitimate request and log a message.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (86 commits)
ipv4: fix redirect handling
ping: dont increment ICMP_MIB_INERRORS
sky2: fix hang in napi_disable
sky2: enforce minimum ring size
bonding: Don't allow mode change via sysfs with slaves present
f_phonet: fix page offset of first received fragment
stmmac: fix pm functions avoiding sleep on spinlock
stmmac: remove spin_lock in stmmac_ioctl.
stmmac: parameters auto-tuning through HW cap reg
stmmac: fix advertising 1000Base capabilties for non GMII iface
stmmac: use mdelay on timeout of sw reset
sky2: version 1.30
sky2: used fixed RSS key
sky2: reduce default Tx ring size
sky2: rename up/down functions
sky2: pci posting issues
sky2: fix hang on shutdown (and other irq issues)
r6040: fix check against MCRO_HASHEN bit in r6040_multicast_list
MAINTAINERS: change email address for shemminger
pch_gbe: Move #include of module.h
...
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
We've been hitting BUG()'s in btrfs_cont_expand and btrfs_fallocate and anywhere
else that calls btrfs_get_extent while running xfstests 13 in a loop. This is
because fiemap is calling btrfs_get_extent with non-sectorsize aligned offsets,
which will end up adding mappings that are not sectorsize aligned, which will
cause problems in some cases for subsequent calls to btrfs_get_extent for
similar areas that are sectorsize aligned. With this patch I ran xfstests 13 in
a loop for a couple of hours and didn't hit the problem that I could previously
hit in at most 20 minutes. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
When doing the io_ctl helpers to clean up the free space cache stuff I stopped
using our normal prepare_pages stuff, which means I of course forgot to do
things like set the pages extent mapped, which will cause us all sorts of
wonderful propblems. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
We've been hitting panics when running xfstest 13 in a loop for long periods of
time. And actually this problem has always existed so we've been hitting these
things randomly for a while. Basically what happens is we get a thread coming
into the allocator and reading the space cache off of disk and adding the
entries to the free space cache as we go. Then we get another thread that comes
in and tries to allocate from that block group. Since block_group->cached !=
BTRFS_CACHE_NO it goes ahead and tries to do the allocation. We do this because
if we're doing the old slow way of caching we don't want to hold people up and
wait for everything to finish. The problem with this is we could end up
discarding the space cache at some arbitrary point in the future, which means we
could very well end up allocating space that is either bad, or when the real
caching happens it could end up thinking the space isn't in use when it really
is and cause all sorts of other problems.
The solution is to add a new flag to indicate we are loading the free space
cache from disk, and always try to cache the block group if cache->cached !=
BTRFS_CACHE_FINISHED. That way if we are loading the space cache anybody else
who tries to allocate from the block group will have to wait until it's finished
to make sure it completes successfully. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
For the user it is confusing to find something like:
[10197.627710] new size for /dev/mapper/vg0-usr_share is 3221225472
in kernel log, because it doesn't point directly to btrfs.
This patch prefixes those messages with "btrfs:" like other btrfs
related printks.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Round inode bytes and delalloc bytes up to real blocksize before
converting to sector size. Otherwise eg. files smaller than 512
are reported with zero blocks due to incorrect rounding.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
