AF_RXRPC doesn't currently enable IPv6 UDP Tx checksums on the transport
socket it opens and the checksums in the packets it generates end up 0.
It probably should also enable IPv6 UDP Rx checksums and IPv4 UDP
checksums. The latter only seem to be applied if the socket family is
AF_INET and don't seem to apply if it's AF_INET6. IPv4 packets from an
IPv6 socket seem to have checksums anyway.
What seems to have happened is that the inet_inv_convert_csum() call didn't
get converted to the appropriate udp_port_cfg parameters - and
udp_sock_create() disables checksums unless explicitly told not too.
Fix this by enabling the three udp_port_cfg checksum options.
Fixes: 1a9b86c9fd ("rxrpc: use udp tunnel APIs instead of open code in rxrpc_open_socket")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Vadim Fedorenko <vfedorenko@novek.ru>
cc: David S. Miller <davem@davemloft.net>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
As udp_port_cfg struct changes its members with dependency on IPv6
configuration, the code in rxrpc should also check for IPv6.
Fixes: 1a9b86c9fd ("rxrpc: use udp tunnel APIs instead of open code in rxrpc_open_socket")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rxrpc_open_socket(), now it's using sock_create_kern() and
kernel_bind() to create a udp tunnel socket, and other kernel
APIs to set up it. These code can be replaced with udp tunnel
APIs udp_sock_create() and setup_udp_tunnel_sock(), and it'll
simplify rxrpc_open_socket().
Note that with this patch, the udp tunnel socket will always
bind to a random port if transport is not provided by users,
which is suggested by David Howells, thanks!
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing encap_enable/increasing encap_needed_key, up->encap_enabled
is not set in rxrpc_open_socket(), and it will cause encap_needed_key
not being decreased in udpv6_destroy_sock().
This patch is to improve it by just calling udp_tunnel_encap_enable()
where it increases both UDP and UDPv6 encap_needed_key and sets
up->encap_enabled.
v4->v5:
- add the missing '#include <net/udp_tunnel.h>', as David Howells
noticed.
Acked-and-tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rewrite the rxrpc client connection manager so that it can support multiple
connections for a given security key to a peer. The following changes are
made:
(1) For each open socket, the code currently maintains an rbtree with the
connections placed into it, keyed by communications parameters. This
is tricky to maintain as connections can be culled from the tree or
replaced within it. Connections can require replacement for a number
of reasons, e.g. their IDs span too great a range for the IDR data
type to represent efficiently, the call ID numbers on that conn would
overflow or the conn got aborted.
This is changed so that there's now a connection bundle object placed
in the tree, keyed on the same parameters. The bundle, however, does
not need to be replaced.
(2) An rxrpc_bundle object can now manage the available channels for a set
of parallel connections. The lock that manages this is moved there
from the rxrpc_connection struct (channel_lock).
(3) There'a a dummy bundle for all incoming connections to share so that
they have a channel_lock too. It might be better to give each
incoming connection its own bundle. This bundle is not needed to
manage which channels incoming calls are made on because that's the
solely at whim of the client.
(4) The restrictions on how many client connections are around are
removed. Instead, a previous patch limits the number of client calls
that can be allocated. Ordinarily, client connections are reaped
after 2 minutes on the idle queue, but when more than a certain number
of connections are in existence, the reaper starts reaping them after
2s of idleness instead to get the numbers back down.
It could also be made such that new call allocations are forced to
wait until the number of outstanding connections subsides.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a helper to directly set the IPV6_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_MTU_DISCOVER sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com> [rxrpc bits]
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly enable timestamps instead of setting the
SO_TIMESTAMP* sockopts from kernel space and going through a fake
uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6
socket as well as UDPv6 when trying to transmit fragmentably.
Without this, packets filled to the normal size used by the kernel AFS
client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE
immediately. The ->sk_error_report() notification hook is called, but
rxrpc doesn't generate a trace for it.
This is a temporary fix; a more permanent solution needs to involve
changing the size of the packets being filled in accordance with the MTU,
which isn't currently done in AF_RXRPC. The reason for not doing so was
that, barring the last packet in an rx jumbo packet, jumbos can only be
assembled out of 1412-byte packets - and the plan was to construct jumbos
on the fly at transmission time.
Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to
engage in this anyway since fragmentation is only done by the sender. We
can then condense the switch-statement in rxrpc_send_data_packet().
Fixes: 75b54cb57c ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The introduction of a split between the reference count on rxrpc_local
objects and the usage count didn't quite go far enough. A number of kernel
work items need to make use of the socket to perform transmission. These
also need to get an active count on the local object to prevent the socket
from being closed.
Fix this by getting the active count in those places.
Also split out the raw active count get/put functions as these places tend
to hold refs on the rxrpc_local object already, so getting and putting an
extra object ref is just a waste of time.
The problem can lead to symptoms like:
BUG: kernel NULL pointer dereference, address: 0000000000000018
..
CPU: 2 PID: 818 Comm: kworker/u9:0 Not tainted 5.5.0-fscache+ #51
...
RIP: 0010:selinux_socket_sendmsg+0x5/0x13
...
Call Trace:
security_socket_sendmsg+0x2c/0x3e
sock_sendmsg+0x1a/0x46
rxrpc_send_keepalive+0x131/0x1ae
rxrpc_peer_keepalive_worker+0x219/0x34b
process_one_work+0x18e/0x271
worker_thread+0x1a3/0x247
kthread+0xe6/0xeb
ret_from_fork+0x1f/0x30
Fixes: 730c5fd42c ("rxrpc: Fix local endpoint refcounting")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix rxrpc_put_local() to not access local->debug_id after calling
atomic_dec_return() as, unless that returned n==0, we no longer have the
right to access the object.
Fixes: 06d9532fa6 ("rxrpc: Fix read-after-free in rxrpc_queue_local()")
Signed-off-by: David Howells <dhowells@redhat.com>
When a local endpoint is ceases to be in use, such as when the kafs module
is unloaded, the kernel will emit an assertion failure if there are any
outstanding client connections:
rxrpc: Assertion failed
------------[ cut here ]------------
kernel BUG at net/rxrpc/local_object.c:433!
and even beyond that, will evince other oopses if there are service
connections still present.
Fix this by:
(1) Removing the triggering of connection reaping when an rxrpc socket is
released. These don't actually clean up the connections anyway - and
further, the local endpoint may still be in use through another
socket.
(2) Mark the local endpoint as dead when we start the process of tearing
it down.
(3) When destroying a local endpoint, strip all of its client connections
from the idle list and discard the ref on each that the list was
holding.
(4) When destroying a local endpoint, call the service connection reaper
directly (rather than through a workqueue) to immediately kill off all
outstanding service connections.
(5) Make the service connection reaper reap connections for which the
local endpoint is marked dead.
Only after destroying the connections can we close the socket lest we get
an oops in a workqueue that's looking at a connection or a peer.
Fixes: 3d18cbb7fd ("rxrpc: Fix conn expiry timers")
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxrpc_queue_local() attempts to queue the local endpoint it is given and
then, if successful, prints a trace line. The trace line includes the
current usage count - but we're not allowed to look at the local endpoint
at this point as we passed our ref on it to the workqueue.
Fix this by reading the usage count before queuing the work item.
Also fix the reading of local->debug_id for trace lines, which must be done
with the same consideration as reading the usage count.
Fixes: 09d2bf595d ("rxrpc: Add a tracepoint to track rxrpc_local refcounting")
Reported-by: syzbot+78e71c5bab4f76a6a719@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
When a local endpoint (struct rxrpc_local) ceases to be in use by any
AF_RXRPC sockets, it starts the process of being destroyed, but this
doesn't cause it to be removed from the namespace endpoint list immediately
as tearing it down isn't trivial and can't be done in softirq context, so
it gets deferred.
If a new socket comes along that wants to bind to the same endpoint, a new
rxrpc_local object will be allocated and rxrpc_lookup_local() will use
list_replace() to substitute the new one for the old.
Then, when the dying object gets to rxrpc_local_destroyer(), it is removed
unconditionally from whatever list it is on by calling list_del_init().
However, list_replace() doesn't reset the pointers in the replaced
list_head and so the list_del_init() will likely corrupt the local
endpoints list.
Fix this by using list_replace_init() instead.
Fixes: 730c5fd42c ("rxrpc: Fix local endpoint refcounting")
Reported-by: syzbot+193e29e9387ea5837f1d@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Fix rxrpc_unuse_local() to handle a NULL local pointer as it can be called
on an unbound socket on which rx->local is not yet set.
The following reproduced (includes omitted):
int main(void)
{
socket(AF_RXRPC, SOCK_DGRAM, AF_INET);
return 0;
}
causes the following oops to occur:
BUG: kernel NULL pointer dereference, address: 0000000000000010
...
RIP: 0010:rxrpc_unuse_local+0x8/0x1b
...
Call Trace:
rxrpc_release+0x2b5/0x338
__sock_release+0x37/0xa1
sock_close+0x14/0x17
__fput+0x115/0x1e9
task_work_run+0x72/0x98
do_exit+0x51b/0xa7a
? __context_tracking_exit+0x4e/0x10e
do_group_exit+0xab/0xab
__x64_sys_exit_group+0x14/0x17
do_syscall_64+0x89/0x1d4
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: syzbot+20dee719a2e090427b5f@syzkaller.appspotmail.com
Fixes: 730c5fd42c ("rxrpc: Fix local endpoint refcounting")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The object lifetime management on the rxrpc_local struct is broken in that
the rxrpc_local_processor() function is expected to clean up and remove an
object - but it may get requeued by packets coming in on the backing UDP
socket once it starts running.
This may result in the assertion in rxrpc_local_rcu() firing because the
memory has been scheduled for RCU destruction whilst still queued:
rxrpc: Assertion failed
------------[ cut here ]------------
kernel BUG at net/rxrpc/local_object.c:468!
Note that if the processor comes around before the RCU free function, it
will just do nothing because ->dead is true.
Fix this by adding a separate refcount to count active users of the
endpoint that causes the endpoint to be destroyed when it reaches 0.
The original refcount can then be used to refcount objects through the work
processor and cause the memory to be rcu freed when that reaches 0.
Fixes: 4f95dd78a7 ("rxrpc: Rework local endpoint management")
Reported-by: syzbot+1e0edc4b8b7494c28450@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public licence as published by
the free software foundation either version 2 of the licence or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 114 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170857.552531963@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
net/rxrpc/local_object.c: In function ‘rxrpc_open_socket’:
net/rxrpc/local_object.c:175:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret < 0) {
^
net/rxrpc/local_object.c:184:2: note: here
case AF_INET:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Currently, GCC is expecting to find the fall-through annotations
at the very bottom of the case and on its own line. That's why
I had to add the annotation, although the intentional fall-through
is already mentioned in a few lines above.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udpv6_encap_enable() function is part of the ipv6 code, and if that is
configured as a loadable module and rxrpc is built in then a build failure
will occur because the conditional check is wrong:
net/rxrpc/local_object.o: In function `rxrpc_lookup_local':
local_object.c:(.text+0x2688): undefined reference to `udpv6_encap_enable'
Use the correct config symbol (CONFIG_AF_RXRPC_IPV6) in the conditional
check rather than CONFIG_IPV6 as that will do the right thing.
Fixes: 5271953cad ("rxrpc: Use the UDP encap_rcv hook")
Reported-by: kbuild-all@01.org
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the UDP encap_rcv hook to cut the bit out of the rxrpc packet reception
in which a packet is placed onto the UDP receive queue and then immediately
removed again by rxrpc. Going via the queue in this manner seems like it
should be unnecessary.
This does, however, require the invention of a value to place in encap_type
as that's one of the conditions to switch packets out to the encap_rcv
hook. Possibly the value doesn't actually matter for anything other than
sockopts on the UDP socket, which aren't accessible outside of rxrpc
anyway.
This seems to cut a bit of time out of the time elapsed between each
sk_buff being timestamped and turning up in rxrpc (the final number in the
following trace excerpts). I measured this by making the rxrpc_rx_packet
trace point print the time elapsed between the skb being timestamped and
the current time (in ns), e.g.:
... 424.278721: rxrpc_rx_packet: ... ACK 25026
So doing a 512MiB DIO read from my test server, with an unmodified kernel:
N min max sum mean stddev
27605 2626 7581 7.83992e+07 2840.04 181.029
and with the patch applied:
N min max sum mean stddev
27547 1895 12165 6.77461e+07 2459.29 255.02
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the rxrpc_data_ready() function to pick up all packets and to not miss
any. There are two problems:
(1) The sk_data_ready pointer on the UDP socket is set *after* it is
bound. This means that it's open for business before we're ready to
dequeue packets and there's a tiny window exists in which a packet can
sneak onto the receive queue, but we never know about it.
Fix this by setting the pointers on the socket prior to binding it.
(2) skb_recv_udp() will return an error (such as ENETUNREACH) if there was
an error on the transmission side, even though we set the
sk_error_report hook. Because rxrpc_data_ready() returns immediately
in such a case, it never actually removes its packet from the receive
queue.
Fix this by abstracting out the UDP dequeuing and checksumming into a
separate function that keeps hammering on skb_recv_udp() until it
returns -EAGAIN, passing the packets extracted to the remainder of the
function.
and two potential problems:
(3) It might be possible in some circumstances or in the future for
packets to be being added to the UDP receive queue whilst rxrpc is
running consuming them, so the data_ready() handler might get called
less often than once per packet.
Allow for this by fully draining the queue on each call as (2).
(4) If a packet fails the checksum check, the code currently returns after
discarding the packet without checking for more.
Allow for this by fully draining the queue on each call as (2).
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
It seems that enabling IPV6_RECVERR on an IPv6 socket doesn't also turn on
IP_RECVERR, so neither local errors nor ICMP-transported remote errors from
IPv4 peer addresses are returned to the AF_RXRPC protocol.
Make the sockopt setting code in rxrpc_open_socket() fall through from the
AF_INET6 case to the AF_INET case to turn on all the AF_INET options too in
the AF_INET6 case.
Fixes: f2aeed3a59 ("rxrpc: Fix error reception on AF_INET6 sockets")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix RTT information gathering in AF_RXRPC by the following means:
(1) Enable Rx timestamping on the transport socket with SO_TIMESTAMPNS.
(2) If the sk_buff doesn't have a timestamp set when rxrpc_data_ready()
collects it, set it at that point.
(3) Allow ACKs to be requested on the last packet of a client call, but
not a service call. We need to be careful lest we undo:
bf7d620abf
Author: David Howells <dhowells@redhat.com>
Date: Thu Oct 6 08:11:51 2016 +0100
rxrpc: Don't request an ACK on the last DATA packet of a call's Tx phase
but that only really applies to service calls that we're handling,
since the client side gets to send the final ACK (or not).
(4) When about to transmit an ACK or DATA packet, record the Tx timestamp
before only; don't update the timestamp afterwards.
(5) Switch the ordering between recording the serial and recording the
timestamp to always set the serial number first. The serial number
shouldn't be seen referenced by an ACK packet until we've transmitted
the packet bearing it - so in the Rx path, we don't need the timestamp
until we've checked the serial number.
Fixes: cf1a6474f8 ("rxrpc: Add per-peer RTT tracker")
Signed-off-by: David Howells <dhowells@redhat.com>
While __atomic_add_unless() was originally intended as a building-block
for atomic_add_unless(), it's now used in a number of places around the
kernel. It's the only common atomic operation named __atomic*(), rather
than atomic_*(), and for consistency it would be better named
atomic_fetch_add_unless().
This lack of consistency is slightly confusing, and gets in the way of
scripting atomics. Given that, let's clean things up and promote it to
an official part of the atomics API, in the form of
atomic_fetch_add_unless().
This patch converts definitions and invocations over to the new name,
including the instrumented version, using the following script:
----
git grep -w __atomic_add_unless | while read line; do
sed -i '{s/\<__atomic_add_unless\>/atomic_fetch_add_unless/}' "${line%%:*}";
done
git grep -w __arch_atomic_add_unless | while read line; do
sed -i '{s/\<__arch_atomic_add_unless\>/arch_atomic_fetch_add_unless/}' "${line%%:*}";
done
----
Note that we do not have atomic{64,_long}_fetch_add_unless(), which will
be introduced by later patches.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/20180621121321.4761-2-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
AF_RXRPC tries to turn on IP_RECVERR and IP_MTU_DISCOVER on the UDP socket
it just opened for communications with the outside world, regardless of the
type of socket. Unfortunately, this doesn't work with an AF_INET6 socket.
Fix this by turning on IPV6_RECVERR and IPV6_MTU_DISCOVER instead if the
socket is of the AF_INET6 family.
Without this, kAFS server and address rotation doesn't work correctly
because the algorithm doesn't detect received network errors.
Fixes: 75b54cb57c ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Permit bind() to be called on an AF_RXRPC socket more than once (currently
maximum twice) to bind multiple listening services to it. There are some
restrictions:
(1) All bind() calls involved must have a non-zero service ID.
(2) The service IDs must all be different.
(3) The rest of the address (notably the transport part) must be the same
in all (a single UDP socket is shared).
(4) This must be done before listen() or sendmsg() is called.
This allows someone to connect to the service socket with different service
IDs and lays the foundation for service upgrading.
The service ID used by an incoming call can be extracted from the msg_name
returned by recvmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
Support network namespacing in AF_RXRPC with the following changes:
(1) All the local endpoint, peer and call lists, locks, counters, etc. are
moved into the per-namespace record.
(2) All the connection tracking is moved into the per-namespace record
with the exception of the client connection ID tree, which is kept
global so that connection IDs are kept unique per-machine.
(3) Each namespace gets its own epoch. This allows each network namespace
to pretend to be a separate client machine.
(4) The /proc/net/rxrpc_xxx files are now called /proc/net/rxrpc/xxx and
the contents reflect the namespace.
fs/afs/ should be okay with this patch as it explicitly requires the current
net namespace to be init_net to permit a mount to proceed at the moment. It
will, however, need updating so that cells, IP addresses and DNS records are
per-namespace also.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the rxrpc_local::services list to just a pointer as we don't permit
multiple service endpoints to bind to a single transport endpoints (this is
excluded by rxrpc_lookup_local()).
The reason we don't allow this is that if you send a request to an AFS
filesystem service, it will try to talk back to your cache manager on the
port you sent from (this is how file change notifications are handled). To
prevent someone from stealing your CM callbacks, we don't let AF_RXRPC
sockets share a UDP socket if at least one of them has a service bound.
Signed-off-by: David Howells <dhowells@redhat.com>
Add CONFIG_AF_RXRPC_IPV6 and make the IPv6 support code conditional on it.
This is then made conditional on CONFIG_IPV6.
Without this, the following can be seen:
net/built-in.o: In function `rxrpc_init_peer':
>> peer_object.c:(.text+0x18c3c8): undefined reference to `ip6_route_output_flags'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 support to AF_RXRPC. With this, AF_RXRPC sockets can be created:
service = socket(AF_RXRPC, SOCK_DGRAM, PF_INET6);
instead of:
service = socket(AF_RXRPC, SOCK_DGRAM, PF_INET);
The AFS filesystem doesn't support IPv6 at the moment, though, since that
requires upgrades to some of the RPC calls.
Note that a good portion of this patch is replacing "%pI4:%u" in print
statements with "%pISpc" which is able to handle both protocols and print
the port.
Signed-off-by: David Howells <dhowells@redhat.com>
Rewrite the data and ack handling code such that:
(1) Parsing of received ACK and ABORT packets and the distribution and the
filing of DATA packets happens entirely within the data_ready context
called from the UDP socket. This allows us to process and discard ACK
and ABORT packets much more quickly (they're no longer stashed on a
queue for a background thread to process).
(2) We avoid calling skb_clone(), pskb_pull() and pskb_trim(). We instead
keep track of the offset and length of the content of each packet in
the sk_buff metadata. This means we don't do any allocation in the
receive path.
(3) Jumbo DATA packet parsing is now done in data_ready context. Rather
than cloning the packet once for each subpacket and pulling/trimming
it, we file the packet multiple times with an annotation for each
indicating which subpacket is there. From that we can directly
calculate the offset and length.
(4) A call's receive queue can be accessed without taking locks (memory
barriers do have to be used, though).
(5) Incoming calls are set up from preallocated resources and immediately
made live. They can than have packets queued upon them and ACKs
generated. If insufficient resources exist, DATA packet #1 is given a
BUSY reply and other DATA packets are discarded).
(6) sk_buffs no longer take a ref on their parent call.
To make this work, the following changes are made:
(1) Each call's receive buffer is now a circular buffer of sk_buff
pointers (rxtx_buffer) rather than a number of sk_buff_heads spread
between the call and the socket. This permits each sk_buff to be in
the buffer multiple times. The receive buffer is reused for the
transmit buffer.
(2) A circular buffer of annotations (rxtx_annotations) is kept parallel
to the data buffer. Transmission phase annotations indicate whether a
buffered packet has been ACK'd or not and whether it needs
retransmission.
Receive phase annotations indicate whether a slot holds a whole packet
or a jumbo subpacket and, if the latter, which subpacket. They also
note whether the packet has been decrypted in place.
(3) DATA packet window tracking is much simplified. Each phase has just
two numbers representing the window (rx_hard_ack/rx_top and
tx_hard_ack/tx_top).
The hard_ack number is the sequence number before base of the window,
representing the last packet the other side says it has consumed.
hard_ack starts from 0 and the first packet is sequence number 1.
The top number is the sequence number of the highest-numbered packet
residing in the buffer. Packets between hard_ack+1 and top are
soft-ACK'd to indicate they've been received, but not yet consumed.
Four macros, before(), before_eq(), after() and after_eq() are added
to compare sequence numbers within the window. This allows for the
top of the window to wrap when the hard-ack sequence number gets close
to the limit.
Two flags, RXRPC_CALL_RX_LAST and RXRPC_CALL_TX_LAST, are added also
to indicate when rx_top and tx_top point at the packets with the
LAST_PACKET bit set, indicating the end of the phase.
(4) Calls are queued on the socket 'receive queue' rather than packets.
This means that we don't need have to invent dummy packets to queue to
indicate abnormal/terminal states and we don't have to keep metadata
packets (such as ABORTs) around
(5) The offset and length of a (sub)packet's content are now passed to
the verify_packet security op. This is currently expected to decrypt
the packet in place and validate it.
However, there's now nowhere to store the revised offset and length of
the actual data within the decrypted blob (there may be a header and
padding to skip) because an sk_buff may represent multiple packets, so
a locate_data security op is added to retrieve these details from the
sk_buff content when needed.
(6) recvmsg() now has to handle jumbo subpackets, where each subpacket is
individually secured and needs to be individually decrypted. The code
to do this is broken out into rxrpc_recvmsg_data() and shared with the
kernel API. It now iterates over the call's receive buffer rather
than walking the socket receive queue.
Additional changes:
(1) The timers are condensed to a single timer that is set for the soonest
of three timeouts (delayed ACK generation, DATA retransmission and
call lifespan).
(2) Transmission of ACK and ABORT packets is effected immediately from
process-context socket ops/kernel API calls that cause them instead of
them being punted off to a background work item. The data_ready
handler still has to defer to the background, though.
(3) A shutdown op is added to the AF_RXRPC socket so that the AFS
filesystem can shut down the socket and flush its own work items
before closing the socket to deal with any in-progress service calls.
Future additional changes that will need to be considered:
(1) Make sure that a call doesn't hog the front of the queue by receiving
data from the network as fast as userspace is consuming it to the
exclusion of other calls.
(2) Transmit delayed ACKs from within recvmsg() when we've consumed
sufficiently more packets to avoid the background work item needing to
run.
Signed-off-by: David Howells <dhowells@redhat.com>
Convert the rxrpc_local::services list to an hlist so that it can be
accessed under RCU conditions more readily.
Signed-off-by: David Howells <dhowells@redhat.com>
Add RCU destruction for connections and calls as the RCU lookup from the
transport socket data_ready handler is going to come along shortly.
Whilst we're at it, move the cleanup workqueue flushing and RCU barrierage
into the destruction code for the objects that need it (locals and
connections) and add the extra RCU barrier required for connection cleanup.
Signed-off-by: David Howells <dhowells@redhat.com>
Kill off the concept of maintaining a bundle of connections to a particular
target service to increase the number of call slots available for any
beyond four for that service (there are four call slots per connection).
This will make cleaning up the connection handling code easier and
facilitate removal of the rxrpc_transport struct. Bundling can be
reintroduced later if necessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide refcount helper functions for connections so that the code doesn't
touch local or connection usage counts directly.
Also make it such that local and peer put functions can take a NULL
pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Rework the local RxRPC endpoint management.
Local endpoint objects are maintained in a flat list as before. This
should be okay as there shouldn't be more than one per open AF_RXRPC socket
(there can be fewer as local endpoints can be shared if their local service
ID is 0 and they share the same local transport parameters).
Changes:
(1) Local endpoints may now only be shared if they have local service ID 0
(ie. they're not being used for listening).
This prevents a scenario where process A is listening of the Cache
Manager port and process B contacts a fileserver - which may then
attempt to send CM requests back to B. But if A and B are sharing a
local endpoint, A will get the CM requests meant for B.
(2) We use a mutex to handle lookups and don't provide RCU-only lookups
since we only expect to access the list when opening a socket or
destroying an endpoint.
The local endpoint object is pointed to by the transport socket's
sk_user_data for the life of the transport socket - allowing us to
refer to it directly from the sk_data_ready and sk_error_report
callbacks.
(3) atomic_inc_not_zero() now exists and can be used to only share a local
endpoint if the last reference hasn't yet gone.
(4) We can remove rxrpc_local_lock - a spinlock that had to be taken with
BH processing disabled given that we assume sk_user_data won't change
under us.
(5) The transport socket is shut down before we clear the sk_user_data
pointer so that we can be sure that the transport socket's callbacks
won't be invoked once the RCU destruction is scheduled.
(6) Local endpoints have a work item that handles both destruction and
event processing. The means that destruction doesn't then need to
wait for event processing. The event queues can then be cleared after
the transport socket is shut down.
(7) Local endpoints are no longer available for resurrection beyond the
life of the sockets that had them open. As soon as their last ref
goes, they are scheduled for destruction and may not have their usage
count moved from 0.
Signed-off-by: David Howells <dhowells@redhat.com>
Separate local endpoint event handling out into its own file preparatory to
overhauling the object management aspect (which remains in the original
file).
Signed-off-by: David Howells <dhowells@redhat.com>
Rename rxrpc_UDP_error_report() to rxrpc_error_report() as it might get
called for something other than UDP.
Signed-off-by: David Howells <dhowells@redhat.com>
Rename files matching net/rxrpc/ar-*.c to get rid of the "ar-" prefix.
This will aid splitting those files by making easier to come up with new
names.
Note that the not all files are simply renamed from ar-X.c to X.c. The
following exceptions are made:
(*) ar-call.c -> call_object.c
ar-ack.c -> call_event.c
call_object.c is going to contain the core of the call object
handling. Call event handling is all going to be in call_event.c.
(*) ar-accept.c -> call_accept.c
Incoming call handling is going to be here.
(*) ar-connection.c -> conn_object.c
ar-connevent.c -> conn_event.c
The former file is going to have the basic connection object handling,
but there will likely be some differentiation between client
connections and service connections in additional files later. The
latter file will have all the connection-level event handling.
(*) ar-local.c -> local_object.c
This will have the local endpoint object handling code. The local
endpoint event handling code will later be split out into
local_event.c.
(*) ar-peer.c -> peer_object.c
This will have the peer endpoint object handling code. Peer event
handling code will be placed in peer_event.c (for the moment, there is
none).
(*) ar-error.c -> peer_event.c
This will become the peer event handling code, though for the moment
it's actually driven from the local endpoint's perspective.
Note that I haven't renamed ar-transport.c to transport_object.c as the
intention is to delete it when the rxrpc_transport struct is excised.
The only file that actually has its contents changed is net/rxrpc/Makefile.
net/rxrpc/ar-internal.h will need its section marker comments updating, but
I'll do that in a separate patch to make it easier for git to follow the
history across the rename. I may also want to rename ar-internal.h at some
point - but that would mean updating all the #includes and I'd rather do
that in a separate step.
Signed-off-by: David Howells <dhowells@redhat.com.
