The ADATA SX6000LNP NVMe SSDs have the same subnqn and, due to this, a
system with more than one of these SSDs will only have one usable.
[ 0.942706] nvme nvme1: ignoring ctrl due to duplicate subnqn (nqn.2018-05.com.example:nvme:nvm-subsystem-OUI00E04C).
[ 0.943017] nvme nvme1: Removing after probe failure status: -22
02:00.0 Non-Volatile memory controller [0108]: Realtek Semiconductor Co., Ltd. Device [10ec:5762] (rev 01)
71:00.0 Non-Volatile memory controller [0108]: Realtek Semiconductor Co., Ltd. Device [10ec:5762] (rev 01)
There are no firmware updates available from the vendor, unfortunately.
Applying the NVME_QUIRK_IGNORE_DEV_SUBNQN quirk for these SSDs resolves
the issue, and they all work after this patch:
/dev/nvme0n1 2J1120050420 ADATA SX6000LNP [...]
/dev/nvme1n1 2J1120050540 ADATA SX6000LNP [...]
Signed-off-by: Misha Nasledov <misha@nasledov.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=g8xI
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190715' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"A later pull request with some followup items. I had some vacation
coming up to the merge window, so certain things items were delayed a
bit. This pull request also contains fixes that came in within the
last few days of the merge window, which I didn't want to push right
before sending you a pull request.
This contains:
- NVMe pull request, mostly fixes, but also a few minor items on the
feature side that were timing constrained (Christoph et al)
- Report zones fixes (Damien)
- Removal of dead code (Damien)
- Turn on cgroup psi memstall (Josef)
- block cgroup MAINTAINERS entry (Konstantin)
- Flush init fix (Josef)
- blk-throttle low iops timing fix (Konstantin)
- nbd resize fixes (Mike)
- nbd 0 blocksize crash fix (Xiubo)
- block integrity error leak fix (Wenwen)
- blk-cgroup writeback and priority inheritance fixes (Tejun)"
* tag 'for-linus-20190715' of git://git.kernel.dk/linux-block: (42 commits)
MAINTAINERS: add entry for block io cgroup
null_blk: fixup ->report_zones() for !CONFIG_BLK_DEV_ZONED
block: Limit zone array allocation size
sd_zbc: Fix report zones buffer allocation
block: Kill gfp_t argument of blkdev_report_zones()
block: Allow mapping of vmalloc-ed buffers
block/bio-integrity: fix a memory leak bug
nvme: fix NULL deref for fabrics options
nbd: add netlink reconfigure resize support
nbd: fix crash when the blksize is zero
block: Disable write plugging for zoned block devices
block: Fix elevator name declaration
block: Remove unused definitions
nvme: fix regression upon hot device removal and insertion
blk-throttle: fix zero wait time for iops throttled group
block: Fix potential overflow in blk_report_zones()
blkcg: implement REQ_CGROUP_PUNT
blkcg, writeback: Implement wbc_blkcg_css()
blkcg, writeback: Add wbc->no_cgroup_owner
blkcg, writeback: Rename wbc_account_io() to wbc_account_cgroup_owner()
...
A smaller cycle this time. Notably we see another new driver, 'Soft
iWarp', and the deletion of an ancient unused driver for nes.
- Revise and simplify the signature offload RDMA MR APIs
- More progress on hoisting object allocation boiler plate code out of the
drivers
- Driver bug fixes and revisions for hns, hfi1, efa, cxgb4, qib, i40iw
- Tree wide cleanups: struct_size, put_user_page, xarray, rst doc conversion
- Removal of obsolete ib_ucm chardev and nes driver
- netlink based discovery of chardevs and autoloading of the modules
providing them
- Move more of the rdamvt/hfi1 uapi to include/uapi/rdma
- New driver 'siw' for software based iWarp running on top of netdev,
much like rxe's software RoCE.
- mlx5 feature to report events in their raw devx format to userspace
- Expose per-object counters through rdma tool
- Adaptive interrupt moderation for RDMA (DIM), sharing the DIM core
from netdev
-----BEGIN PGP SIGNATURE-----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=iWcG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A smaller cycle this time. Notably we see another new driver, 'Soft
iWarp', and the deletion of an ancient unused driver for nes.
- Revise and simplify the signature offload RDMA MR APIs
- More progress on hoisting object allocation boiler plate code out
of the drivers
- Driver bug fixes and revisions for hns, hfi1, efa, cxgb4, qib,
i40iw
- Tree wide cleanups: struct_size, put_user_page, xarray, rst doc
conversion
- Removal of obsolete ib_ucm chardev and nes driver
- netlink based discovery of chardevs and autoloading of the modules
providing them
- Move more of the rdamvt/hfi1 uapi to include/uapi/rdma
- New driver 'siw' for software based iWarp running on top of netdev,
much like rxe's software RoCE.
- mlx5 feature to report events in their raw devx format to userspace
- Expose per-object counters through rdma tool
- Adaptive interrupt moderation for RDMA (DIM), sharing the DIM core
from netdev"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (194 commits)
RMDA/siw: Require a 64 bit arch
RDMA/siw: Mark expected switch fall-throughs
RDMA/core: Fix -Wunused-const-variable warnings
rdma/siw: Remove set but not used variable 's'
rdma/siw: Add missing dependencies on LIBCRC32C and DMA_VIRT_OPS
RDMA/siw: Add missing rtnl_lock around access to ifa
rdma/siw: Use proper enumerated type in map_cqe_status
RDMA/siw: Remove unnecessary kthread create/destroy printouts
IB/rdmavt: Fix variable shadowing issue in rvt_create_cq
RDMA/core: Fix race when resolving IP address
RDMA/core: Make rdma_counter.h compile stand alone
IB/core: Work on the caller socket net namespace in nldev_newlink()
RDMA/rxe: Fill in wc byte_len with IB_WC_RECV_RDMA_WITH_IMM
RDMA/mlx5: Set RDMA DIM to be enabled by default
RDMA/nldev: Added configuration of RDMA dynamic interrupt moderation to netlink
RDMA/core: Provide RDMA DIM support for ULPs
linux/dim: Implement RDMA adaptive moderation (DIM)
IB/mlx5: Report correctly tag matching rendezvous capability
docs: infiniband: add it to the driver-api bookset
IB/mlx5: Implement VHCA tunnel mechanism in DEVX
...
This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list. This necessitates a large number of driver
changes because the previous guarantee that if a driver specified
SG_ALL as the size of its scatter list, it would get a non-chained
list and didn't need to bother with scatterlist iterators is now
broken and every driver *must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTzzCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZB+AP9I8j/s
wWfg0Z3WNuf4D5I3rH4x1J3cQTqPJed+RjwgcQEA1gZvtOTg1ZEn/CYMVnaB92x0
t6MZSchIaFXeqfD+E7U=
=cv8o
-----END PGP SIGNATURE-----
Merge tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
When we validate the new controller id, we want to skip
controllers that are either deleting or dead. Fix the check
to do that and not on the newly added controller.
Fixes: 1b1031ca63 ("nvme: validate cntlid during controller initialisation")
Reported-by: Jon Derrick <jonathan.derrick@intel.com>
Tested-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Current code allows the module to be unloaded even if there are
pending data structures, such as localports and controllers on
the localports, that have yet to hit their reference counting
to remove them.
Fix by having exit entrypoint explicitly delete every controller,
which in turn will remove references on the remoteports and localports
causing them to be deleted as well. The exit entrypoint, after
initiating the deletes, will wait for the last localport to be deleted
before continuing.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
According to commit a10674bf24 ("tcp: detecting the misuse of
.sendpage for Slab objects") and previous discussion, tcp_sendpage
should not be used for pages that is managed by SLAB, as SLAB is not
taking page reference counters into consideration.
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There was a few false alarms sighted on target side about wrong data
digest while performing high throughput load to XFS filesystem shared
through NVMoF TCP.
This flag tells the rest of the kernel to ensure that the data buffer
does not change while the write is in flight. It incurs a performance
penalty, so only enable it when it is actually needed, i.e. when we are
calculating data digests.
Although even with this change in place, ext2 users can steel experience
false positives, as ext2 is not respecting this flag. This may be apply
to vfat as well.
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Signed-off-by: Mike Playle <mplayle@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Adding this hint for the sake of convenience.
It was spotted that a few times people spent some time before
understanding what is exactly wrong in configuration process. This
should save a few time in such situations, especially for people who
is not very confident with NVMe requirements.
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme_ns_remove() will first set the NVME_NS_REMOVING flag before removing
it from the list at the very last step.
So to avoid selecting a namespace in nvme_find_path() which is about to be
removed check the NVME_NS_REMOVING flag, too, when selecting a new path.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When we have a singular list in nvme_round_robin_path() we still
need to check its validity.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Factor our a common helper to check if a path has been disabled
by something other than the per-namespace ANA state.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: split from a bigger patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
>From the NVMe 1.4 spec:
NSFEAT bit 4 if set to 1: indicates that the fields NPWG, NPWA, NPDG, NPDA,
and NOWS are defined for this namespace and should be used by the host for
I/O optimization;
[ ... ]
Namespace Preferred Write Granularity (NPWG): This field indicates the
smallest recommended write granularity in logical blocks for this namespace.
This is a 0's based value. The size indicated should be less than or equal
to Maximum Data Transfer Size (MDTS) that is specified in units of minimum
memory page size. The value of this field may change if the namespace is
reformatted. The size should be a multiple of Namespace Preferred Write
Alignment (NPWA). Refer to section 8.25 for how this field is utilized to
improve performance and endurance.
[ ... ]
Each Write, Write Uncorrectable, or Write Zeroes commands should address a
multiple of Namespace Preferred Write Granularity (NPWG) (refer to Figure
245) and Stream Write Size (SWS) (refer to Figure 515) logical blocks (as
expressed in the NLB field), and the SLBA field of the command should be
aligned to Namespace Preferred Write Alignment (NPWA) (refer to Figure 245)
for best performance.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make the NVMe NAWUN, NAWUPF, NACWU, NPWG, NPWA, NPDG and NOWS attributes
available to initator systems for the block backend.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are two spelling mistakes in trace_seq_printf messages, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When running a NVMe device that is attached to a addressing
challenged PCIe root port that requires bounce buffering, our
request sizes can easily overflow the swiotlb bounce buffer
size. Limit the maximum I/O size to the limit exposed by
the DMA mapping subsystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Tested-by: Atish Patra <Atish.Patra@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Modify nvme_alloc_sq_cmds() to call pci_free_p2pmem() to free the memory
it allocated using pci_alloc_p2pmem() in case pci_p2pmem_virt_to_bus()
returns null.
Makes sure not to call pci_free_p2pmem() if pci_alloc_p2pmem() returned
NULL, which can happen if CONFIG_PCI_P2PDMA is not configured.
The current implementation is not expected to leak since
pci_p2pmem_virt_to_bus() is expected to fail only if pci_alloc_p2pmem()
returns null. However, checking the return value of pci_alloc_p2pmem()
is more explicit.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Only request an IRQ mapping for read queues if at least one read queue
is being allocted, as nvme_pci_map_queues() will later on ignore the
unnecessary mapping request should nvme_dev_add() request such an IRQ
mapping even though no read queues are being allocated. However,
nvme_dev_add() can avoid making the request by checking the number of
read queues without assuming. This would bring it more in line with
nvme_setup_irqs() and nvme_calc_irq_sets().
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since Linux 5.0 drivers can safely set the largest DMA mask supported
by the device, and don't need fallbacks to work around the dma mapping
implementations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Fix sparse warning:
drivers/nvme/host/pci.c:2926:25: warning:
symbol 'nvme_dev_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
With additional debugging enabled, seeing warnings for suspicious RCU
usage or Sleeping function called from invalid context.
These both map to allocation of a work structure which is currently
GFP_KERNEL, meaning it can sleep. For the RCU warning, the sequence was
sleeping while holding the RCU lock.
Convert the allocation to GFP_ATOMIC.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
With extra debug on, inconsistent lock state warnings are being called
out as the tfcp_req->reqlock is being taken out without irq, while some
calling sequences have the sequence in a softirq state.
Change the lock taking/release to raise/drop irq.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Os1seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGtx4H/j6i482XzcGFKTBm
A7mBoQpy+kLtoUov4EtBAR62OuwI8rsahW9di37QKndPoQrczWaKBmr3De6LCdPe
v3pl3O6wBbvH5ru+qBPFX9PdNbDvimEChh7LHxmMxNQq3M+AjZAZVJyfpoiFnx35
Fbge+LZaH/k8HMwZmkMr5t9Mpkip715qKg2o9Bua6dkH0AqlcpLlC8d9a+HIVw/z
aAsyGSU8jRwhoAOJsE9bJf0acQ/pZSqmFp0rDKqeFTSDMsbDRKLGq/dgv4nW0RiW
s7xqsjb/rdcvirRj3rv9+lcTVkOtEqwk0PVdL9WOf7g4iYrb3SOIZh8ZyViaDSeH
VTS5zps=
=huBY
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc6' into rdma.git for-next
For dependencies in next patches.
Resolve conflicts:
- Use uverbs_get_cleared_udata() with new cq allocation flow
- Continue to delete nes despite SPDX conflict
- Resolve list appends in mlx5_command_str()
- Use u16 for vport_rule stuff
- Resolve list appends in struct ib_client
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is a preparation for adding new signature API to the rw-API.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This enables to inject errors into the commands submitted to the admin
queue.
It is useful to test error handling in the controller initialization.
# echo 100 > /sys/kernel/debug/nvme0/fault_inject/probability
# echo 1 > /sys/kernel/debug/nvme0/fault_inject/times
# echo 10 > /sys/kernel/debug/nvme0/fault_inject/space
# nvme reset /dev/nvme0
# dmesg
...
nvme nvme0: Could not set queue count (16385)
nvme nvme0: IO queues not created
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currenlty fault injection support for nvme only enables to inject errors
into the commands submitted to I/O queues.
In preparation for fault injection into the admin commands, this makes
the helper functions independent of struct nvme_ns.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch introduces target-side request tracing. As Christoph
suggested, the trace would not be in a core or module to avoid
disadvantages like cache miss:
http://lists.infradead.org/pipermail/linux-nvme/2019-June/024721.html
The target-side trace code is entirely based on the Johannes's trace code
from the host side. It has lots of codes duplicated, but it would be
better than having advantages mentioned above.
It also traces not only fabrics commands, but also nvme normal commands.
Once the codes to be shared gets bigger, then we can make it common as
suggsted.
This also removed the create_sq and create_cq trace parsing functions
because it will be done by the connect fabrics command.
Example:
echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_init/enable
echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_complete/enable
cat /sys/kernel/debug/tracing/trace
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[hch: fixed the symbol namespace and a an endianess conversion]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The "result" field is in 64bit to be printed out which means it could be
like:
nvme_complete_rq: nvme0: qid=0, cmdid=0, res=18446612684158962624, etries=0, flags=0x0, status=0
Switch both the result and status field to be printed in hexadecimal
format to be easier to read.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch introduces fabrics commands tracing feature from host-side.
This patch does not include any changes for the previous host-side
tracing, but just add fabrics commands parsing in cmd=() format.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[hch: fixed some whitespace damage]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patches are going to provide the target-side trace which
might need these kind of macros. It would be great if it can be shared
between host and target side both.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme_trace_disk_name() is now already being invoked with the function
prototype in trace.h. We don't need to export this symbol at all.
The following patches are going to provide target-side trace feature
with the exactly same function with this so that this patch removes the
EXPORT_SYMBOL() for this function.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove the status parameter o nvme_remove_dead_ctrl(), which is only
used for printing it.
We move the print message to the same function where actual error is
occurring.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the state change to NVME_CTRL_CONNECTING fails, the dmesg is going to
be like:
[ 293.689160] nvme nvme0: failed to mark controller CONNECTING
[ 293.689160] nvme nvme0: Removing after probe failure status: 0
Even it prints the first line to indicate the situation, the second line
is not proper because the status is 0 which means normally success of
the previous operation.
This patch makes it indicate the proper error value when it fails.
[ 25.932367] nvme nvme0: failed to mark controller CONNECTING
[ 25.932369] nvme nvme0: Removing after probe failure status: -16
This situation is able to be easily reproduced by:
root@target:~# rmmod nvme && modprobe nvme && rmmod nvme
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch removes the confusing assignment of the variable result at
the time of declaration and sets the value in error cases next to the
places where the actual error is happening.
Here we also set the result value to -ENODEV when we fail at the final
ctrl state transition in nvme_reset_work(). Without this assignment
result will hold 0 from nvme_setup_io_queue() and on failure 0 will be
passed to he nvme_remove_dead_ctrl() from final state transition.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
queue_count_set() seems like that it has been provided to limit the
number of queue entries for write/poll queues. But, the
queue_count_set() has been doing nothing but a parameter check even it
has num_possible_cpus() which is nop.
This patch removes entire queue_count_ops from the write_queues and
poll_queues.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
poll_queues will be zero even without zero initialization here.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The nvme pci driver prepares its devices for power loss during suspend
by shutting down the controllers. The power setting is deferred to
pci driver's power management before the platform removes power. The
suspend-to-idle mode, however, does not remove power.
NVMe devices that implement host managed power settings can achieve
lower power and better transition latencies than using generic PCI power
settings. Try to use this feature if the platform is not involved with
the suspend. If successful, restore the previous power state on resume.
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
[hch: fixed the compilation for the !CONFIG_PM_SLEEP case]
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch introduces a nvme_is_fabrics() inline function to check
whether or not the given command structure is for fabrics.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Future use intends to make use of both, so export these functions. And
since their implementation is identical except for the opcode, provide a
new function that implement both.
[akinobu.mita@gmail.com>: fix line over 80 characters]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a shared namespace is removed, we call blk_cleanup_queue()
when the device can still be accessed as the current path and this can
result in submission to a dying queue. Hence, direct_make_request()
called by our mpath device may fail (propagating the failure to userspace).
Instead, we want to failover this I/O to a different path if one exists.
Thus, before we cleanup the request queue, we make sure that the device is
cleared from the current path nor it can be selected again as such.
Fix this by:
- clear the ns from the head->list and synchronize rcu to make sure there is
no concurrent path search that restores it as the current path
- clear the mpath current path in order to trigger a subsequent path search
and sync srcu to wait for any ongoing request submissions
- safely continue to namespace removal and blk_cleanup_queue
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When looking at console messages to troubleshoot, there are one
maybe two messages before creation of the controller is complete.
However, a lot of io takes place to reach that point. It's unclear
when things have started.
Add a message when the controller is attempting to create a new
association. Thus we know what controller, between what host and
remote port, and what NQN is being put into place for any
subsequent success or failure messages.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update fcloop to support the discovery_event operation and
invoke a nvme rescan. In a real fc adapter, this would generate an
RSCN, which the host would receive and convert into a nvme rescan
on the remote port specified in the rscn payload.
Signed-off-by: James Smart <jsmart2021@gmail.com>
[kbuild-bot: fcloop_tgt_discovery_evt can be static]
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery_change transport op.
In turn, the transport adds it's own LLDD api callback discovery_event
op to request the LLDD to generate an RSCN for the discovery change.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some transports, such as FC-NVME, support discovery controller change
events without the use of a persistent discovery controller. FC receives
events via RSCN from the FC Fabric Controller or subsystem FC port.
This patch adds a nvmet transport op that is called whenever a
discovery change event occurs in the nvmet layer.
To facilitate the callback without adding another layer to cross into
core.c to reference the transport ops, the port structure snapshots
the transport ops when the port is enabled and clears them when disabled.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
sg_alloc_table_chained() currently allows the caller to provide one
preallocated SGL and returns if the requested number isn't bigger than
size of that SGL. This is used to inline an SGL for an IO request.
However, scattergather code only allows that size of the 1st preallocated
SGL to be SG_CHUNK_SIZE(128). This means a substantial amount of memory
(4KB) is claimed for the SGL for each IO request. If the I/O is small, it
would be prudent to allocate a smaller SGL.
Introduce an extra parameter to sg_alloc_table_chained() and
sg_free_table_chained() for specifying size of the preallocated SGL.
Both __sg_free_table() and __sg_alloc_table() assume that each SGL has the
same size except for the last one. Change the code to allow both functions
to accept a variable size for the 1st preallocated SGL.
[mkp: attempted to clarify commit desc]
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: netdev@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lightnvm should have never used this function, as it is sending
passthrough requests, so switch it to blk_rq_append_bio like all the
other passthrough request users. Inline blk_init_request_from_bio into
the only remaining caller.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe fixes from Sagi.
* 'nvme-5.2-rc-next' of git://git.infradead.org/nvme:
nvme-rdma: use dynamic dma mapping per command
nvme: Fix u32 overflow in the number of namespace list calculation
nvmet: fix data_len to 0 for bdev-backed write_zeroes
nvme-tcp: fix queue mapping when queue count is limited
nvme-rdma: fix queue mapping when queue count is limited
