The commit bb475230b8 ("reset: make optional functions really optional")
brought a missed part of the support for an optional reset handlers.
Since that we don't need to have special error handling in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit c62ebb3d5f ("i2c: designware: Add support for an interface clock")
introduced an optional clock while missed correct error handling.
assert reset line back if error happen at ->probe().
Fixes: c62ebb3d5f ("i2c: designware: Add support for an interface clock")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Synopsys I2C Controller has an interface clock, but most SoCs hide
this away. However, on some SoCs you need to explicitly enable the
interface clock in order to access the registers. Therefore, add
support for an optional interface clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Before this commit the i2c-designware-platdrv assumes that if the pdev
has an apci-companion it should use a dynamic adapter-nr and it sets
adapter->nr to -1, otherwise it will use pdev->id as adapter->nr.
There are 3 ways how platform_device-s to which i2c-designware-platdrv
will bind can be instantiated:
1) Through of / devicetree
2) Through ACPI enumeration
3) Explicitly instantiated through platform_device_create + add
1) In case of devicetree-instantiation the drivers/of code always sets
pdev->id to PLATFORM_DEVID_NONE, which is -1 so in this case both paths
to set adapter->nr end up doing the same thing.
2) In case of ACPI instantiation the device will always have an
ACPI-companion, so we are already using dynamic adapter-nrs.
3) There are 2 places manually instantiating a designware_i2c platform_dev:
drivers/mfd/intel_quark_i2c_gpio.c
drivers/mfd/intel-lpss.c
In the intel_quark_i2c_gpio.c case pdev->id is always 0, so switching to
dynamic adapter-nrs here could lead to the bus-number no longer being
stable, but the quark X1000 only has 1 i2c-controller, which will also
be assigned bus-number 0 when using dynamic adapter-nrs.
In the intel-lpss.c case intel_lpss_probe() is called from either
intel-lpss-acpi.c in which case there always is an ACPI-companion, or
from intel-lpss-pci.c. In most cases devices handled by intel-lpss-pci.c
also have an ACPI-companion, so we use a dynamic adapter-nr. But in some
cases the ACPI-companion is missing and we would use pdev->id (allocated
from intel_lpss_devid_ida). Devices which use the intel-lpss-pci.c code
typically have many i2c busses, so using pdev->id in this case may lead
to a bus-number conflict, triggering a WARN(id < 0, "couldn't get idr")
in i2c-core-base.c causing an oops an the adapter registration to fail.
So in this case using non dynamic adapter-nrs is actually undesirable.
One machine on which this oops was triggering is the Apollo Lake based
Acer TravelMate Spin B118.
TL;DR: Switching to always using dynamic adapter-numbers does not make
any difference in most cases and in the one case where it does make a
difference the behavior change is desirable because the old behavior
caused an oops.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1687065
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c-designware-platdrv assumes that if the pdev has an apci-companion
it should use a dynamic adapter-nr and otherwise it will use pdev->id
as adapter-nr.
Before this commit the setting of the adapter.nr was somewhat convoluted,
in the acpi_companion case it was set from dw_i2c_acpi_configure, in the
non acpi_companion case it was set from dw_i2c_set_fifo_size based on
tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was
not executed.
This cleans this up, directly setting the adapter-nr from
dw_i2c_plat_probe for both cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On most Intel Bay- and Cherry-Trail systems the PMIC is connected over I2C
and the PMIC is accessed through various means by the _PS0 and _PS3 ACPI
methods (power on / off methods) of various devices.
This leads to suspend/resume ordering problems where a device may be
resumed and get its _PS0 method executed before the I2C controller is
resumed. On Cherry Trail this leads to errors like these:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
But on Bay Trail this caused I2C reads to seem to succeed, but they end
up returning wrong data, which ends up getting written back by the typical
read-modify-write cycle done to turn on various power-resources.
Debugging the problems caused by this silent data corruption is quite
nasty. This commit adds a check which disallows i2c_dw_xfer() calls to
happen until the controller's resume method has completed.
Which turns the silent data corruption into getting these errors in
dmesg instead:
i2c_designware 80860F41:04: Error i2c_dw_xfer call while suspended
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.PCI0.GFX0._PS0, AE_ERROR
Which is much better.
Note the above errors are an example of issues which this patch will
help to debug, the actual fix requires fixing the suspend order and
this has been fixed by a different commit.
Note the setting / clearing of the suspended flag in the suspend / resume
methods is NOT protected by i2c_lock_bus(). This is intentional as these
methods get called from i2c_dw_xfer() (through pm_runtime_get/put) a nd
i2c_dw_xfer() is called with the i2c_bus_lock held, so otherwise we would
deadlock. This means that there is a theoretical race between a non runtime
suspend and the suspended check in i2c_dw_xfer(), this is not a problem
since normally we should not hit the race and this check is primarily a
debugging tool so hitting the check if there are suspend/resume ordering
problems does not need to be 100% reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rework the handling of the P-unit semaphore on Intel Baytrail and
Cherrytrail systems to avoid race conditions and excessive overhead
related to it (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4oYh
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Rework the handling of the P-unit semaphore on Intel Baytrail and
Cherrytrail systems to avoid race conditions and excessive overhead
related to it (Hans de Goede)"
* tag 'acpi-4.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: xpower: Add depends on IOSF_MBI to Kconfig entry
i2c: designware: Cleanup bus lock handling
ACPI / PMIC: xpower: Block P-Unit I2C access during read-modify-write
x86: baytrail/cherrytrail: Rework and move P-Unit PMIC bus semaphore code
Now that most of the special Bay- / Cherry-Trail bus lock handling has
been moved to the iosf_mbi code we can simplify the remaining code a bit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over a LPSS I2C controller. The GPU
is a PCI device and PCI devices are powered-on at the resume_noirq resume
phase.
Since the GPU power-resources need the I2C controller, recent acpi_lpss.c
changes now also power-up the LPSS I2C controllers on BYT and CHT devices
in the resume_noirq resume phase. But during this phase the IRQ of the
controller is disabled leading to these errors:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
This commit makes the i2c-designware controller set the IRQF_NO_SUSPEND
flag when requesting the interrupt on BYT and CHT devices, so that the IRQ
is left enabled during the noirq phase, fixing this.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a3d411fb38 ("i2c: designware: Disable pm for PMIC i2c-bus even if
there is no _SEM method"), always set the pm_disabled flag on the I2C7
controller, even if its bus was not shared with the PUNIT.
This was a workaround for various suspend/resume issues, after the
following 2 commits this workaround is no longer necessary:
Commit 5415277283 ("PM: i2c-designware-platdrv: Suspend/resume at the
late/early stages")
Commit e6ce0ce34f ("ACPI / LPSS: Add device link for CHT SD card
dependency on I2C")
Therefor this commit removes this workaround.
After this commit the pm_disabled flag is only used to indicate that the
bus is shared with the PUNIT and after other recent changes we no longer
call dev_pm_syscore_device(dev, true), so we are no longer actually
disabling (non-runtime) pm, so this commit also renames the flag to
shared_with_punit to better reflect what it is for.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Microsemi Ocelot I2C controller is a designware IP. It also has a
second set of registers to allow tweaking SDA hold time and spike
filtering.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[wsa: made one function static]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the #ifdef CONFIG_OF section to the top of the file, after the ACPI
section so functions defined there can be used in dw_i2c_plat_probe.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to device_get_match_data in probe to match the device specific data
instead of using the acpi specific function.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.
After commit 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).
On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.
The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.
But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.
The _PS3 method for this I2C controller looks like this:
Method (_PS3, 0, NotSerialized) // _PS3: Power State 3
{
If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
{
Return (Zero)
}
PSAT |= 0x03
Local0 = PSAT /* \_SB_.I2C5.PSAT */
}
Where PMID = 0x05, so we enter the Return (Zero) path on these systems.
So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.
Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.
Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.
This commit implements this fix by:
1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.
2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.
Fixes: 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace short statement in comment with proper SPDX license tag.
Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has the following changes for you:
- new flag to mark DMA safe buffers in i2c_msg. Also, some
infrastructure around it. And docs.
- huge refactoring of the at24 driver led by the new maintainer
Bartosz
- update I2C bus recovery to send STOP after recovery
- conversion from gpio to gpiod for I2C bus recovery
- adding a fault-injector to the i2c-gpio driver
- lots of small driver improvements, and bigger ones to
i2c-sh_mobile"
* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
i2c: mv64xxx: Add myself as maintainer for this driver
i2c: mv64xxx: Fix clock resource by adding an optional bus clock
i2c: mv64xxx: Remove useless test before clk_disable_unprepare
i2c: mxs: use true and false for boolean values
i2c: meson: update doc description to fix build warnings
i2c: meson: add configurable divider factors
dt-bindings: i2c: update documentation for the Meson-AXG
i2c: imx-lpi2c: add runtime pm support
i2c: rcar: fix some trivial typos in comments
i2c: davinci: fix the cpufreq transition
i2c: rk3x: add proper kerneldoc header
i2c: rk3x: account for const type of of_device_id.data
i2c: acorn: remove outdated path from file header
i2c: acorn: add MODULE_LICENSE tag
i2c: rcar: implement bus recovery
i2c: send STOP after successful bus recovery
i2c: ensure SDA is released in recovery if SDA is controllable
i2c: add 'set_sda' to bus_recovery_info
i2c: add identifier in declarations for i2c_bus_recovery
i2c: make kerneldoc about bus recovery more precise
...
Optimize the power management in i2c-designware-platdrv by making it
set the DPM_FLAG_SMART_SUSPEND and DPM_FLAG_LEAVE_SUSPENDED which
allows some code to be dropped from its PM callbacks.
First, setting DPM_FLAG_SMART_SUSPEND causes the intel-lpss driver
to avoid resuming i2c-designware-platdrv devices in its ->prepare
callback, so they can stay in runtime suspend after that point even
if the direct-complete feature is not used for them.
It also causes the ACPI PM domain and the PM core to avoid invoking
"late" and "noirq" suspend callbacks for these devices if they are
in runtime suspend at the beginning of the "late" phase of device
suspend during system suspend. That guarantees dw_i2c_plat_suspend()
to be called for a device only if it is not in runtime suspend.
Moreover, it causes the device's runtime PM status to be set to
"active" after calling dw_i2c_plat_resume() for it, so the
driver doesn't need internal flags to avoid invoking either
dw_i2c_plat_suspend() or dw_i2c_plat_resume() twice in a row.
Second, setting DPM_FLAG_LEAVE_SUSPENDED enables the optimization
allowing the device to stay suspended after system resume under
suitable conditions, so again the driver doesn't need to take
care of that by itself.
Accordingly, the internal "suspended" and "skip_resume" flags
used by the driver are not necessary any more, so drop them and
simplify the driver's PM callbacks.
Additionally, notice that dw_i2c_plat_complete() only needs to
schedule runtime PM resume for the device if platform firmware
has been involved in resuming the system, so make it call
pm_resume_via_firmware() to check that. Also make it check the
runtime PM status of the device instead of its direct_complete
flag which also works if the device remained suspended due to
the DPM_FLAG_LEAVE_SUSPENDED driver flag.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Modify i2c-designware-platdrv to set DPM_FLAG_SMART_PREPARE for its
devices and return 0 from the system suspend ->prepare callback
if the device has an ACPI companion object in order to tell the PM
core and middle layers to avoid skipping system suspend/resume
callbacks for the device in that case (which may be problematic,
because the device may be accessed during suspend and resume of
other devices via I2C operation regions then).
Also the pm_runtime_suspended() check in dw_i2c_plat_prepare()
is not necessary any more, because the core does it when setting
power.direct_complete for the device, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
For consistency with the rest of the file rename function and parameter to
be consistent with the reset of the common file.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the i2c_dw_plat_prepare_clk funciton to common file in preparation
for its use also by the master driver.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to data sheet SCL timing parameters and DW_IC_CON SPEED mode
bits are not used when operating in slave mode.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't populate const array supported_speeds on the stack, instead
make it static. Makes the object code smaller by 150 bytes:
Before:
text data bss dec hex filename
8474 1440 0 9914 26ba i2c-designware-platdrv.o
After:
text data bss dec hex filename
8324 1440 0 9764 2624 i2c-designware-platdrv.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported by Rajat Jain, there are problems when ACPI operation
region handlers or similar, called at the ->resume_early() time, for
I2C client devices try to access an I2C controller that has already
been suspended at that point. To avoid that, move the suspend/resume
of i2c-designware-platdrv to the late/early stages, respectively.
While at it, avoid resuming the device from runtime suspend in the
driver's ->suspend callback which isn't particularly nice. [A better
approach would be to make the driver track the PM state of the device
so that it doesn't need to resume it in ->suspend, so implement it.]
First, drop dw_i2c_plat_suspend() added by commit a23318feef (i2c:
designware: Fix system suspend) and rename dw_i2c_plat_runtime_suspend()
back to dw_i2c_plat_suspend().
Second, point the driver's ->late_suspend and ->early_resume
callbacks, rather than its ->suspend and ->resume callbacks,
to dw_i2c_plat_suspend() and dw_i2c_plat_resume(), respectively,
so that they are not executed in parallel with each other, for
example if runtime resume of the device takes place during system
suspend.
Finally, add "suspended" and "skip_resume" flags to struct dw_i2c_dev
and make dw_i2c_plat_suspend() and dw_i2c_plat_resume() use them to
avoid suspending or resuming the device twice in a row and to avoid
resuming a previously runtime-suspended device during system resume.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The power management handling in dw_i2c_plat_probe() is somewhat
messy and it is rather hard to figure out the code intention for
the case when pm_disabled is set. In that case, the driver doesn't
enable runtime PM at all, but in addition to that it calls
pm_runtime_forbid() as though it wasn't sure if runtime PM might
be enabled for the device later by someone else.
Although that concern doesn't seem to be actually valid, the
device is clearly still expected to be PM-capable even in the
pm_disabled set case, so a better approach would be to enable
runtime PM for it unconditionally and prevent it from being
runtime-suspended by using pm_runtime_get_noresume().
Make the driver do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- new drivers for Spreadtrum I2C, Intel Cherry Trail Whiskey Cove SMBUS
- quite some driver updates
- cleanups for the i2c-mux subsystem
- some subsystem-wide constification
- further cleanup of include/linux/i2c
* 'i2c/for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (50 commits)
i2c: sprd: Fix undefined reference errors
i2c: nomadik: constify amba_id
i2c: versatile: Make i2c_algo_bit_data const
i2c: busses: make i2c_adapter_quirks const
i2c: busses: make i2c_adapter const
i2c: busses: make i2c_algorithm const
i2c: Add Spreadtrum I2C controller driver
dt-bindings: i2c: Add Spreadtrum I2C controller documentation
i2c-cht-wc: make cht_wc_i2c_adap_driver static
MAINTAINERS: Add entry for drivers/i2c/busses/i2c-cht-wc.c
i2c: aspeed: Retain delay/setup/hold values when configuring bus frequency
dt-bindings: i2c: eeprom: Document vendor to be used and deprecated ones
i2c: i801: Restore the presence state of P2SB PCI device after reading BAR
MAINTAINERS: drop entry for Blackfin I2C and Sonic's email
blackfin: merge the two TWI header files
i2c: davinci: Preserve return value of devm_clk_get
i2c: mediatek: Add i2c compatible for MediaTek MT7622
dt-bindings: i2c: Add MediaTek MT7622 i2c binding
dt-bindings: i2c: modify information formats
i2c: mux: i2c-arb-gpio-challenge: allow compiling w/o OF support
...
The Lenovo Miix2 8 DSDT contains an i2c clk / bus speed of 1700000 Hz
for one if its devices, which is not supported.
This is the second DSDT to show up with an unsupported clk in a short
time, remove the hardcoded fix for DSDTs with a 1 MiHz clock and simply
always round down the clk to the nearest supported value.
Reported-by: russianneuromancer@ya.ru
Fixes: 682c6c2188 ("i2c: designware: Some broken DSTDs use 1MiHz ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Code sets bit DW_IC_CON_SPEED_FAST (0x4) always when configuring the slave
mode. This results incorrect register value DW_IC_CON_SPEED_HIGH (0x6)
when OR'ed together with DW_IC_CON_SPEED_STD (0x2).
Remove this and let the code set the speed mode bits according to clock
frequency or default to fast mode.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit 8503ff1665 ("i2c: designware: Avoid unnecessary resuming
during system suspend"), may suggest to the PM core to try out the so
called direct_complete path for system sleep. In this path, the PM core
treats a runtime suspended device as it's already in a proper low power
state for system sleep, which makes it skip calling the system sleep
callbacks for the device, except for the ->prepare() and the ->complete()
callbacks.
However, the PM core may unset the direct_complete flag for a parent
device, in case its child device are being system suspended before. In this
scenario, the PM core invokes the system sleep callbacks, no matter if the
device is runtime suspended or not.
Particularly in cases of an existing i2c slave device, the above path is
triggered, which breaks the assumption that the i2c device is always
runtime resumed whenever the dw_i2c_plat_suspend() is being called.
More precisely, dw_i2c_plat_suspend() calls clk_core_disable() and
clk_core_unprepare(), for an already disabled/unprepared clock, leading to
a splat in the log about clocks calls being wrongly balanced and breaking
system sleep.
To still allow the direct_complete path in cases when it's possible, but
also to keep the fix simple, let's runtime resume the i2c device in the
->suspend() callback, before continuing to put the device into low power
state.
Note, in cases when the i2c device is attached to the ACPI PM domain, this
problem doesn't occur, because ACPI's ->suspend() callback, assigned to
acpi_subsys_suspend(), already calls pm_runtime_resume() for the device.
It should also be noted that this change does not fix commit 8503ff1665
("i2c: designware: Avoid unnecessary resuming during system suspend").
Because for the non-ACPI case, the system sleep support was already broken
prior that point.
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Several drivers call to_platform_device() to get platform_device
and pass it to platform_get_drvdata(). In platform_get_drvdata(),
the platform_device is converted back to struct device again.
Use dev_get_drvdata() to avoid platform_device/device dance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for DesignWare only)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least the Acer Iconia Tab8 / aka W1-810 uses 1MiHz instead of
1MHz for one of its busses, fix this up to 1MHz instead of failing
the probe of that bus.
This fixes the accelerometer on the Acer Iconia Tab8 not working.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we refuse to probe due to an invalid clock frequency, log
the frequency which is causing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Slave mode selected in platform module if the support is detected in
the DT.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- The functions related to I2C master mode of operation were transformed
in a single driver.
- Common definitions were moved to i2c-designware-core.h
- The i2c-designware-core is now only a library file, the functions
associated are in a source file called i2c-designware-common and
are used by both i2c-designware-master and i2c-designware-slave.
- To decrease noise in namespace common i2c_dw_*() functions are
now using ops to keep them private.
- Designware PCI driver had to be changed to match the previous ops
functions implementation.
Almost all of the "core" source is now part of the "master" source. The
difference is the functions used by both modes and they are in the
"common" source file.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Factor out all _master() part of code from i2c-designware-core
and i2c-designware-platdrv to separate functions.
- Standardize all code related with MASTER mode.
- I have to take off DW_IC_INTR_TX_EMPTY from DW_IC_INTR_DEFAULT_MASK
because it is master specific.
The purpose of this is to prepare the controller to have is I2C MASTER
flow in a separate driver. To do this first all the
functions/definitions related to the MASTER flow were identified.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The purpose of this commit is to fix some comments and styling in the
existing code due to the need of reuse this code. What is being made
here is:
- Sorted the headers files
- Corrected some comments style (capital letters, lowcase i2c)
- Reverse tree in the variables declaration
- Add/remove empty lines and tabs where needed
- Fix of misspelled word "endianness" and "transferred"
- Replaced the return variable "r" with the more standard "ret"
The value of this, besides the rules of coding style, is because I
will use this code after and it will make my future patch a lot bigger and
complicated to review. The work here won't bring any additional work to
backported fixes because is just style and reordering.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Fixes: 9d64084330 ("i2c: designware: don't infer timings described by ACPI from clock rate")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bd698d24b1 ("i2c: designware: Get selected speed mode
sda-hold-time via ACPI") updated the logic that reads the timing
parameters for various I2C bus rates from the DSDT, to only read
the timing parameters for the currently selected mode.
This causes a WARN_ON() splat on platforms that legally omit the clock
frequency from the ACPI description, because in the new situation, the
core I2C designware driver still accesses the fields in the driver
struct that we no longer populate, and proceeds to calculate them from
the clock frequency. Since the clock frequency is unspecified, the
driver complains loudly using a WARN_ON().
So revert back to the old situation, where the struct fields for all
timings are populated, but retain the new logic which chooses the SDA
hold time from the timing mode that is currently in use.
Fixes: bd698d24b1 ("i2c: designware: Get selected speed mode ...")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Update the ACPICA code in the kernel to upstream revision
20170303 which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box,
Lv Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the
ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo,
Hans de Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it
(Hans de Goede).
- Move the code turning off unused ACPI power resources during
system resume to a point after all devices have been resumed
to avoid issues with power resources that do not behave as
expected (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ytsi
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170303 which adds a few minor fixes and improvements, update ACPI
SoC drivers with new device IDs, platform-related information and
similar, fix the register information in the xpower PMIC driver,
introduce a concept of "always present" devices to the ACPI device
enumeration code and use it to fix a problem with one platform, and
fix a system resume issue related to power resources.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170303
which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box, Lv
Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the ACPI
drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de
Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it (Hans de
Goede).
- Move the code turning off unused ACPI power resources during system
resume to a point after all devices have been resumed to avoid
issues with power resources that do not behave as expected (Hans de
Goede)"
* tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI / power: Delay turning off unused power resources after suspend
ACPI / PMIC: xpower: Fix power_table addresses
ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
ACPI / bus: Add INT0002 to list of always-present devices
...
Add ACPI HID HISI02A1 and HISI02A2 for Hisilicon Hip07/08,
which have different clock frequency.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sda-hold-time is an important parameter for tuning i2c to meet the
electrical specification especially for high speed. I2C with incorrect
sda-hold-time may cause lost arbitration error. Instead of loading all
speed mode settings, only selected speed mode settings are loaded.
Signed-off-by: Tan Chin Yew <chin.yew.tan@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cherrytrail devices use the dw i2c-bus with uid 7 to access their PMIC.
Even if the i2c-bus to the PMIC is not shared with the SoC's P-Unit
and i2c-designware-baytrail.c thus does not set the pm_disabled flag,
we still need to disable pm so that ACPI PMIC opregions can access the
PMIC during late-suspend and early-resume.
This fixes errors like these blocking suspend:
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently we are already setting a pm_runtime_disabled flag and disabling
runtime-pm for i2c-busses used for accessing the system PMIC on x86.
But this is not enough, there are ACPI opregions which may want to access
the PMIC during late-suspend and early-resume, so we need to completely
disable pm to be safe.
This commit renames the flag from pm_runtime_disabled to pm_disabled and
adds the following new behavior if the flag is set:
1) Call dev_pm_syscore_device(dev, true) which disables normal suspend /
resume and remove the pm_runtime_disabled check from dw_i2c_plat_resume
since that will now never get called. This fixes suspend_late handlers
which use ACPI PMIC opregions causing errors like these:
PM: Suspending system (freeze)
PM: suspend of devices complete after 1127.751 msecs
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
2) Set IRQF_NO_SUSPEND irq flag. This fixes resume_early handlers which
handlers which use ACPI PMIC opregions causing errors like these:
PM: resume from suspend-to-idle
i2c_designware 808622C1:06: controller timed out
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull immutable branch as a common base for further development:
"Baytrail PMIC vs. PMU race fixes from Hans de Goede
This time the right version (v4), with the compile fix."
Some platforms like hi3660 need do reset first to allow accessing registers
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ramiro Oliveira <ramiro.oliveira@synopsys.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The cherrytrail punit has the pmic i2c bus access semaphore at a
different register address.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-9-hdegoede@redhat.com
On my cherrytrail tablet with axp288 pmic, just doing a bunch of repeated
reads from the pmic, e.g. "i2cdump -y 14 0x34" would lookup the tablet in
1 - 3 runs guaranteed.
This seems to be causes by the cpu trying to enter C6 or C7 while we hold
the punit bus semaphore, at which point everything just hangs.
Avoid this by disallowing the CPU to enter C6 or C7 before acquiring the
punit bus semaphore.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-7-hdegoede@redhat.com
Rename accessor_flags to flags, so that we can use the field for
other flags too. This is a preparation patch for adding cherrytrail
support to the punit semaphore code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-4-hdegoede@redhat.com
ACPI always sets Tx/Rx FIFO to 32. This configuration will
cause problem if the IP core supports a FIFO size of less than 32.
The driver should read the FIFO size from the IP and select the smaller
one of the two.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a common place for default functionality bits for both platform
and pci driver.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
