There's no need for these queue funcs to be inlined, so drop the
markings. This shaves off a few hundred duplicated bytes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This array isn't written anywhere, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rather than hardcoding the register sizes/offsets in this file, use the
existing struct in the spi header for reading/writing the hardware.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The default bits per word setting should be 8 bits, but since most of our
devices have been explicitly setting this up, we didn't notice when the
default stopped working.
At the moment, any default transfers without an explicit bit size setting
error out with:
bfin-spi bfin-spi.0: transfer: unsupported bits_per_word
So in the transfer logic, have a bits_per_word setting of 0 fall into the
8 bit transfer logic.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The platform configuration can select custom FIFO watermarks, but
these may conflict the actual FIFO size of the PL022 variant if
set too high. So strengthen the sanity checks to deny any
conflicting settings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Insert notifiers for the runtime PM API. With this the runtime
PM layer kicks in to action where used.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Rebased to Linux 3.0-rc3, edit description]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Configure the DMA burstsize from the FIFO trigger level supplied
with the controller configuration data. This is based on a patch
from Virupax, but I rewrote it differently.
Reported-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Return error on out of range cpsdvsr value.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch enables this SPI driver works with DMA mode.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support ML7213 device of OKI SEMICONDUCTOR.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is compatible for Intel EG20T PCH.
v4: - Delete unrelated whitespace
- Prevent device driver from accessing platform data
- Add __devinit and __devexit
- Save pdev->dev to pd_dev->dev.parent
- Have own suspend/resume processing in platform_driver.
- Care returned value in pch_spi_init
- Change unregister order
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds DMA support for the EP93xx SPI driver. By default the DMA is
not enabled but it can be enabled by setting ep93xx_spi_info.use_dma to true
in board configuration file.
Note that the SPI driver still uses PIO for small transfers (<= 8 bytes) for
performance reasons.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
SPI protocol drivers can submit messages specifying needed bits_per_word
parameter for a message transfer. The bitbang driver currently ignores
bits_per_word given by a singe message and always uses master's
bits_per_word parameter. Only use master's bits_per_word when a
message didn't specify needed bits_per_word for ongoing transfer.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
fixes below compilation warning. The variable doesn't actual ever get
used uninitialized, but that's no reason to be sloppy.
drivers/spi/omap2_mcspi.c: In function 'omap2_mcspi_txrx_dma':
drivers/spi/omap2_mcspi.c:301: warning: 'elements' may be used uninitialized in this function
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[grant.likely: amended description]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Blackfin SPORT peripheral is a pretty flexible device. With enough
coaching, we can make it generate SPI compatible waveforms. This is
desirable as the SPORT can run at much higher clock frequencies than the
dedicated on-chip SPI peripheral, and it can do full duplex DMA. It also
opens up the possibility of multiple SPI buses in case someone wants to
dedicate a whole bus to a specific part that does not play well with
others.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch includes below fixes:
1. Add missing device_remove_file for dev_attr_status_show in tle62x0_remove.
2. Fix tle62x0_probe error handling:
Currently, if the error happens when ptr > 0, gpio_attrs[0] is not
properly remove.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
regulator: Fix 88pm8607.c printk format warning
input: Add support for Qualcomm PMIC8XXX power key
input: Add Qualcomm pm8xxx keypad controller driver
mfd: Add omap-usbhs runtime PM support
mfd: Fix ASIC3 SD Host Controller Configuration size
mfd: Fix omap_usbhs_alloc_children error handling
mfd: Fix omap usbhs crash when rmmoding ehci or ohci
mfd: Add ASIC3 LED support
leds: Add ASIC3 LED support
mfd: Update twl4030-code maintainer e-mail address
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
mfd: Provide ab8500-core enumerators for chip cuts
mfd: Check twl4030-power remove script error condition after i2cwrite
mfd: Fix twl6030 irq definitions
mfd: Add phoenix lite (twl6025) support to twl6030
mfd: Avoid to use constraint name in 88pm860x regulator driver
mfd: Remove checking on max8925 regulator[0]
mfd: Remove unused parameter from 88pm860x API
mfd: Avoid to allocate 88pm860x static platform data
...
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
spi/amba-pl022: work in polling or interrupt mode if pl022_dma_probe fails
spi/spi_s3c24xx: Use spi_bitbang_stop instead of spi_unregister_master in s3c24xx_spi_remove
spi/spi_nuc900: Use spi_bitbang_stop instead of spi_unregister_master in nuc900_spi_remove
spi/spi_tegra: use spi_unregister_master() instead of spi_master_put()
spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path
spi: Use void pointers for data in simple SPI I/O operations
spi/pl022: use cpu_relax in the busy loop
spi/pl022: mark driver non-experimental
spi/pl022: timeout on polled transfer v2
spi/dw_spi: improve the interrupt mode with the batch ops
spi/dw_spi: change poll mode transfer from byte ops to batch ops
spi/dw_spi: remove the un-necessary flush()
spi/dw_spi: unify the low level read/write routines
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If pl022_dma_probe fails, we can try to transfer data in polling or interrupt
mode. Also, set platform_info->enable_dma to 0, so that no other code tries to
use dma.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Calling spi_bitbang_stop() will also destroy bitbang->workqueue,
which is created by calling spi_bitbang_start() in s3c24xx_spi_probe().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Calling spi_bitbang_stop() will also destroy bitbang->workqueue,
which is created by calling spi_bitbang_start() in nuc900_spi_probe().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi_master_put() should only be used in error handling.
Once spi_register_master() returns success, we should call
spi_unregister_master() instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi_master_put() should only be used in error handling.
Once spi_register_master() returns success, we should call
spi_unregister_master() instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently the simple SPI I/O operations all take pointers to u8 * buffers
to operate on. This creates needless type compatibility issues and the
underlying spi_transfer structure uses void pointers anyway so convert the
API over to take void pointers too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This relaxes the cpu in the polling busy-wait loop.
Reported-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver has no TODO, and is now used on several platforms:
ARM, U300, Ux500, SPEAr and more. So drop the EXPERIMENTAL
requirement.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds the missing handling of polling timeouts and deletes
our last todo.
Signed-off-by: Magnus Templing <magnus.templing@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixups from review by Wolfram Sang]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
dt/fsldma: fix build warning caused by of_platform_device changes
spi: Fix race condition in stop_queue()
gpio/pch_gpio: Fix output value of pch_gpio_direction_output()
gpio/ml_ioh_gpio: Fix output value of ioh_gpio_direction_output()
gpio/pca953x: fix error handling path in probe() call
There's a race condition in stop_queue() in some drivers -
if drv_data->queue is empty, but drv_data->busy is still set
(or opposite situation) stop_queue will return -EBUSY.
So fix loop condition to check that both drv_data->queue is empty
and drv_data->busy is not set.
This patch affects following drivers:
pxa2xx_spi
spi_bfin5xx
amba-pl022
dw_spi
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
leverage the performance gain by change in low level
read/write batch operations
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current poll transfer will read/write one word, then wait till the
hw is non-busy, it's not efficient. This patch will try to read/write
as many words as permitted by hardware FIFO depth.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The flush() is used to drain all the left data in rx fifo, currently
is is always called together with disabling hw. But from spec, disabling
hw will also reset all the fifo, so flush() is not needed.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The original version has many duplicated codes for null/u8/u16 case,
so unify them to make it cleaner
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: Add loopback support for the SPI on 5500
spi/omap_mcspi: Fix broken last word xfer
of/flattree: minor cleanups
dt: eliminate OF_NO_DEEP_PROBE and test for NULL match table
dt: protect against NULL matches passed to of_match_node()
dt: Refactor of_platform_bus_probe()
Extend the vendor data with a loopback field, and add new
amba-pl022 vendor data for the DB5500 pl023, as the pl023
on db8500 and db5500 vary.
Signed-off-by: Prajadevi H <prajadevi.h@stericsson.com>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit adef658 "spi/omap_mcspi: catch xfers of non-multiple SPI word size"
broke the transmission of last word in cases where access is multiple of
word size and word size is 16 or 32 bits.
Fix this by replacing the test "c > (word_len>>3)" in do-while loops with
"c >= 'pointer increment size'". This ensures that the last word is
transmitted in above case and still allow to break the loop and prevent
variable c underflow in cases where word size != 'pointer increment size'.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
include/linux/dw_spi.h only includes driver internal data. It doesn't
expose a platform_data configuration structure or similar (at least
nothing in-tree). This patch moves the header into drivers/spi so
that the scope is limited to only the dw_spi_*.c driver files
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Feng Tang <feng.tang@intel.com>
Cc: spi-devel-general@lists.sourceforge.net
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
This patch adds an SPI master implementation that operates on top of an
underlying TI-SSP port.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current davinci SPI driver, in DMA mode, is limited to 65535
words for a single transfer. Modify the driver by configuring a
3 dimensional EDMA transfer to support up to 65535x65535
words.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The davinci spi driver provides an option to use DMA transfers for
data. In the dma_map_single() call, the driver is passing the
number of words to be transfered for the mapping size. It should
be the number of bytes.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If an SPI access was not a multiple of the SPI word size,
the while() loop would spin and the rx/tx ptrs would be incremented
indefinitely.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For DMA operation, the davinci spi driver needs an event queue number.
Currently, this number is passed as a IORESOURCE_DMA. This is not
correct, as the event queue is not a DMA channel. Pass the event queue
via the platform data structure instead.
On dm355 and dm365, move the eventq assignment for spi0 out of resources
array and into platform data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Get rid of users of of_platform_driver in drivers/spi. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Off-by-one error, gave erroneous divisor value 16 if speed_hz is over zero but
less than OMAP2_MCSPI_MAX_FREQ / (1 << 15), that is, [1..1463].
Also few overly complex bit shifts in divisor fixed.
Also one dev_dgb line fixed, which indicated max speed exceeding transfer speed.
Introducing a new function omap2_mcspi_calc_divisor() for getting the right
divisor in omap2_mcspi_setup_transfer().
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Hannu Heikkinen <ext-hannu.m.heikkinen@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove a compilation error regarding unused labels that came about
when simplifying the DMA code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SH7757 has SPI0 module. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[grant.likely@secretlab.ca: fixed Makefile ordering, added
__dev{init,exit} annotations, removed DRIVER_VERSION (this is
mainline, the version == the kernel version) and tidied some
indentation & style stuff]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds a new SPI driver to support the Altera SOPC Builder
SPI component. It uses the bitbanging library.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support of OpenCores tiny SPI driver.
http://opencores.org/project,tiny_spi
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
McSPI runtime conversion.
Changes involves:
1) remove clock framework apis to use runtime framework apis.
2) context restore from runtime resume which is a callback for get_sync.
3) Remove SYSCONFIG(sysc) register handling
(a) Remove context save and restore of sysc reg and remove soft reset
done from sysc reg as this will be done with hwmod framework.
(b) Also cleanup sysc reg bit macros.
4) Rename the omap2_mcspi_reset function to omap2_mcspi_master_setup
function as with hwmod changes soft reset will be done in
hwmod framework itself and use the return value from clock
enable function to return for failure scenarios.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleans up all base address definitions for omap_mcspi
and adapts the device registration and driver to hwmod framework.
Changes involves:
1) Removing all base address macro defines.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute(number of chipselect).
3) Appending base address with pdata reg_offset for omap4 boards.
For omap4 all regs used in driver deviate with reg_offset_macros
defined with an value of 0x100. So pass this offset through pdata
and append the same to base address retrieved from hwmod data file
and we are not mapping *_HL_* regs which are not used in driver.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The hardware seems to have a race condition when the inactive
channels are in slave mode. We support master mode only, so
we can just switch all channels to master mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[ukleinek: add more verbose comment about the race]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This utilizes the new core voltage switch to power off the PL022
core voltage when it's not in use transmitting packets, if and
only if a core voltage switch is available.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This simplifies the DMA code a bit by using the dmaengine helpers.
The cookie from descriptor submission can be ignored in this case
as has been established in review of the MMCI/PL180 driver.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
setup_transfer is mandatory if spi_bitbang_transfer is used, so
check for it during initialization and not each time during runtime.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If there is an error with setting up a transfer, we need to return
immediately rather than trying to continue to process things. We
already set up the error states for the caller at this point.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We can do multiples of 8bit transfers when using the hardware CS and a
little bit of magic, so make it work.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Right now the platform device and its platform data is included in one big
struct which requires its custom ->release function. The problem with the
release function within the driver is that it might be called after the
driver was removed because someone was holding a reference to it and it
was not called right after platform_device_unregister(). So we also free
the platform device memory to which one might hold a reference.
This patch uses the normal pdev functions so this kind of race does not
occur.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the compat_ioctl for operations on /dev/spi* so that 32 bit
userspace applications can access SPI. As far as I can see all data
structure are already prepared for that, so no additional conversion has
to be done.
My use case is MIPS with N32 userspace ABI and toolchain, and that was
also the platform where I tested it successfully (Cavium Octeon).
Signed-off-by: Bernhard Walle <walle@corscience.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Instead of sending data 8 bits at a time in 8-bit SPI mode, swap bytes
and send and receive them 32 bits at a time. Tested with an SD-card,
with which this patch reduced the number of interrupts by 50%, when
reading 5MiB of data (there are also small service packets, the number
of interrupts, produced by 512-byte sectors should, of course, drop by
75%), and improved throughput by more than 40%.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
NULL + <small offset> != NULL, but reading from that <small offset> address
is usually not a very good idea and often leads to problems, like kernel
Oopses in this case, easily reproducible by writing to an SD-card, used in
SPI mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Without this fix reloading of the driver is impossible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
clk_freq is used uninitialized in pl022_setup routine. This patch
fix compilation warning for using uninitialized variable
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch enables the existing S3C64XX series SPI driver for S5P64X0
and removed dependency on EXPERIMENTAL because we don't need it now.
v3: Changed dependency of S3C64XX_DMA
v2: Removed dependency on EXPERIMENTAL
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
