This is a new version of my patch, now using a module parameter instead
of a sysctl, so that the option is harder to find. Please note that,
once the module is loaded, it is still possible to change the value of
the parameter in /sys/module/sctp/parameters/, which is useful if you
want to do performance comparisons without rebooting.
Computation of SCTP checksums significantly affects the performance of
SCTP. For example, using two dual-Opteron 246 connected using a Gbe
network, it was not possible to achieve more than ~730 Mbps, compared to
941 Mbps after disabling SCTP checksums.
Unfortunately, SCTP checksum offloading in NICs is not commonly
available (yet).
By default, checksums are still enabled, of course.
Signed-off-by: Lucas Nussbaum <lucas.nussbaum@ens-lyon.fr>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver uses advanced descriptors for its main functionality,
but then uses legacy when testing. This patch changes this so that
advanced descriptors are used throughout and all mentions of legacy
descriptors are removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all of the unused defines from the .h files contained in
igb. For some defines there was a use and so I plugged them into the correct
locations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch combines a pair of if statements into one.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP Checksum enable doesn't need packet split in order to function. It only
requires the use of advanced descriptors which the current igb driver does.
So we can enable it always without any issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Adaptive Interrupt Moderation algorithm so that the low latency
state is triggered less easily to prevent high interrupt loads.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is intended to hold several whitespace, formatting, and
comment cleanups that have been found while cleaning up the igb driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Controlled by a compile-time (Kconfig) option for now, since it
isn't a win in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the mp->default_[rt]x_ring_size variables to ->[rt]x_ring_size,
allow them to be read via the standard ethtool ->get_ringparam() op,
and add a ->set_ringparam() op to allow resizing them at run time.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch:
- increases the precision of the receive/transmit interrupt
coalescing register value computations by using 64bit temporaries;
- adds functions to read the current hardware coalescing register
values and convert them back to usecs;
- exports the {get,set} {rx,tx} coal methods via the standard
ethtool coalescing interface.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a waste having two different versions of this structure around
when the differences between ethtool ops for phy'd and phy-less
interfaces are so minor.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiffies are unsigned long, make sure we fit in jiffies store variable
on archs with bits per long > 32.
Patch suggested by Jiri Slaby.
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/isdn/mISDN/clock.c:44:1: warning: symbol 'iclock_lock' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:45:9: warning: symbol 'iclock_count' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:46:17: warning: symbol 'iclock_tv' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:47:9: warning: symbol 'iclock_tv_valid' was not declared. Should it be static?
drivers/isdn/mISDN/clock.c:48:20: warning: symbol 'iclock_current' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/isdn/hardware/mISDN/hfcpci.c:59:19: warning: symbol 'hfc_tl' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcpci.c:60:9: warning: symbol 'hfc_jiffies' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.h:201:6: warning: symbol 'conf_str' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.h:319:12: warning: symbol 'HFC_TE_LAYER1_STATES' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.h:331:12: warning: symbol 'HFC_NT_LAYER1_STATES' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.c:38:12: warning: symbol 'hfcsusb_rev' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.c:978:1: warning: symbol 'fill_isoc_urb' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcsusb.c:1724:1: warning: symbol 'setup_hfcsusb' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whitespaces, empty lines, 80 columns, indentations and removing redundant
parenthesis
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-arrange the driver debug print to support the Tx multi-queue and add support
for debug prints at the end of the ring (when start<end)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolving the majority of the issues, but there are still some left for future
patches.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the device info from the chip shared memory - rename to avoid confusion
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading in diag mode, set the device to loopback instead of normal link and
then changing it to loopback mode
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver default WoL setting is set to the nvram default value
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling many debug prints, it can take a while before processing an event.
To ease the debug process, allow bigger timeout before giving up
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows better debug capabilities if the user wants to force an MRRS value
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supporting non-default pre-emphasis settings for the internal and some external
PHYs
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is disabled, so removing it to avoid confusion
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This 1G interface (on top of the 4 lanes 10G interface) requires additional
setting to work in CL45
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIG_ENABLE does not reset the emac. Replace it with explicit reset
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs (like the BCM8726) FW version cannot be read after activating the
PHY, so we need to save this information
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some dual port PHY require HW lock since they are used by both interfaces
(different driver instances). Since this list is getting longer, update a
parameter at load time instead of calculating it on runtime
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also adding the ability to recognize the optic module and disable it if it is
not authorized for safety reasons - since this feature might upset some users
which are willing to take the risk, it is optional and can be disabled by
setting an nvram bit (or a trivial driver patch to set this bit).
This dual port PHY requires special handling if the ports are swapped.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A GPIO is used with the 8726 PHY. Adding the GPIO related functions in this
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are too many different board types and this field is not scalable.
Removing it and making decisions according to other fields
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting better HW thresholds and enabling FW capabilities for better
enforcement. Also set the HW to more efficiently use the internal buffers if
this is a single port design
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the configuration can be set when loading the device and shouldn't be
re-calculated after each link up indication since it is not dependent on the
link speed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should be called for all incoming packets and not just for GRO packets
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
