Added the sysfs attribute for non fatal log so that management utility can
get the non fatal dump from driver. The non-fatal error is an error
condition or abnormal behavior detected by the host, or detected and
reported by the controller to the host.The non-fatal error does not stop
the controller firmware and enables it to still respond to host requests.
A typical example of a non-fatal error is an I/O timeout or an unusual
error notification from the controller. Since the firmware is operational,
the error dump information is pushed to host memory (by firmware) upon
request from the host.
Link: https://lore.kernel.org/r/20200316074906.9119-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm80xx driver, the command mpi_set_phy_profile_req is sent by host
during boot to configure the phy profile such as analog setting page, rate
control page. However, the tag is not freed when its response is
received. As a result, 16 tags are missing for each HBA after boot. When
NCQ is enabled with queue depth 16, it needs at least, 15 * 16 = 240 tags
for each HBA to achieve the best performance. In current pm80xx driver with
setting CCB_MAX = 256, the total number of tags in each HBA is 255 for data
IO. Hence, without returning those tags to the pool after boot, some device
will finally be forced to non-ncq mode by ATA layer due to excessive errors
(i.e. LLDD cannot allocate tag for queued task).
Link: https://lore.kernel.org/r/20200316074906.9119-4-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: yuuzheng <yuuzheng@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A kexec reboot causes the controller fw to assert. This assertion shows up
in two ways, the controller doesn't show up as ready and an interrupt is
waiting as soon as the handler is registered. To resolve this added below
fix:
- Split the interrupt handling setup into two parts, setup and request.
- If the controller ready register indicates not-ready, but that the not
readiness is only on the IOC units we can still try a reset to bring the
system back to the pre-reboot state.
Link: https://lore.kernel.org/r/20200316074906.9119-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a pm8001_printk message. Fix it.
Link: https://lore.kernel.org/r/20200123005706.2834281-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove #include <linux/version.h>. Don't need it.
Link: https://lore.kernel.org/r/20191122020911.33269-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The condition (reg_val != 2) || (reg_val != 3) will always be true because
reg_val cannot be equal to two different values at the same time. Fix this
by replacing the || operator with && so that the loop will loop if reg_val
is not a 2 and not a 3 as was originally intended.
Fixes: 50dc2f221455 ("scsi: pm80xx: Modified the logic to collect fatal dump")
Link: https://lore.kernel.org/r/20191120135031.270708-1-colin.king@canonical.com
Addresses-Coverity: ("Constant expression result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the correct method to collect the fatal dump.
Link: https://lore.kernel.org/r/20191114100910.6153-14-deepak.ukey@microchip.com
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Occasionally, 6G capable drives fail to train at 6G on links that look good
from a signal-integrity perspective. PMC suggests configuring the port to
not even expect 12G.
Link: https://lore.kernel.org/r/20191114100910.6153-11-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commands to the controller are sent in fixed sized chunks which are set
per-chip-generation and stashed in iomb_size. The driver fills in structs
matching the register layout and memcpy this to memory shared with the
controller. However, there are two problem cases:
1) Things like phy_start_req are too large because they share the
sas_identify_frame definition with libsas, and it includes the crc
word. This means that it's overwriting the start of the next
command block, that's ok except if it happens at the end of the
shared memory area.
2) Things like set_nvm_data_req which are shared between the HAL
layers. This means that it's sending 'random' data for things that
are in the reserved area. So far we haven't found a case where the
controller FW cares, but sending possible gibberish (for most of
the structures this is in the reserved area so previously zeroed)
is not recommended.
Link: https://lore.kernel.org/r/20191114100910.6153-9-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function mpi_uninit_check takes longer for inbound doorbell register to
be cleared. Increased the timeout substantially so that the driver does not
fail to load.
Link: https://lore.kernel.org/r/20191114100910.6153-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: ianyar <ianyar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default logging doesn't include the device name, so it's difficult to
determine which controller is being logged about in error scenarios. The
logging level was only settable via sysfs, which made it inconvenient for
actual debugging. This changes the default to only cover error handling.
Link: https://lore.kernel.org/r/20191114100910.6153-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For delays longer than 20ms [um]delay isn't recommended.
pm80xx_chip_soft_rst starts off with a 500ms delay before it even gets
around to checking for the results of the reset. As long as it's at least
500ms it doesn't matter what the scheduler is doing. The delay in the
pm8001_exec_internal_task_abort does nothing, and theory is this is a delay
to avoid a double-free.
Link: https://lore.kernel.org/r/20191114100910.6153-5-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the completing the mpi_phy_start_resp, make phy enable completion as
NULL.
Link: https://lore.kernel.org/r/20191114100910.6153-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was missing complete() call in mpi_sata_completion which result in
SATA abort error handling timing out. That causes the device to be left in
the in_recovery state so subsequent commands sent to the device fail and
the OS removes access to it.
Link: https://lore.kernel.org/r/20191114100910.6153-2-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the functions pm8001_chip_is_our_interupt,
pm80xx_chip_is_our_interupt and function pointer is_our_interrupt to fix
spelling mistakes.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When macro PM8001_USE_MSIX is defined there are redundant dead code calls
to pm8001_chip_intx_interrupt_{enable|disable} and pm8001_cr32.
Clean this up for the defined PM8001_USE_MSIX and undefined
PM8001_USE_MSIX cases.
[mkp: squashed two patches]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several lines of code where the indentation is at an incorrect
level; fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm80xx_hwi.c: In function 'pm8001_set_phy_profile':
drivers/scsi/pm8001/pm80xx_hwi.c:4679:6: warning:
variable 'page_code' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added proper mask for phy id in mpi_phy_stop_resp().
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when there's an error in 'ncq mode' the host has to read the ncq error
log (10h) to clear the error state. however, the ccb that is setup for
doing this doesn't setup the ccb so that the previous state is
cleared. if the ccb was previously used for an IO n_elems is set and
pm8001_ccb_task_free() treats this as the signal to go free a
scatter-gather list (that's already been freed).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified SATA abort handling with following steps:
1) Set device state as recovery.
2) Send phy reset.
3) Wait for reset completion.
4) After successful reset, abort all IO's to the device.
5) After aborting all IO's to device, set device state as operational.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added port reset timer value as 2000ms for PM8006 sata controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tag is taken from the tag pool instead of using the hardcoded tag
value(1).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Different SAS addresses are assigned for each set of phys.
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to read ILA version and inactive firmware version from MPI
configuration table and export through sysfs.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ATTO adapters do not support this feature. If the firmware fails to be
ready, it should not check the examined registers in order to examine
the state of the feature in order to prevent undefined behavior.
Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PHY profiles are not saved in NVRAM on ATTO 12Gb SAS controllers.
Therefore, in order for the controller to function in a wide range of
configurations, the PHY profiles must be statically set. This patch
provides the necessary functionality to do so.
Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case psataPayload->status has a status of IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
ts->stat gets set to SAS_OPEN_REJECT but a missing 'break' statement causes a
fallthrough to the default handler of the switch statement overriding ts->stat
to SAS_DEV_NO_RESPONSE.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The request has to be retried incase if the length of the SSP
Response IU is invalid.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
PORT RECOVERY TIMEOUT is the maximum time between the controller's
detection of the PHY down until the receipt of the ID_Frame (from the
same remote SAS port). If the time expires before the ID_FRAME is
received, the port is considered INVALID and can be removed. The
IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the
IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after
Port Recovery Time.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If the link error happens, we don't need to disconnect the phy,
which will remove the drive. Instead acknowledging the controller
and logging the error will be enough.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Thermal page code has been changed to 7 for the 12G controllers.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use the ata device class from libata in libsas instead of checking
the supported command set and switch to using ata_dev_classify()
instead of our own method.
Cc: Tejun Heo <tj@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppche
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The driver ignores the return value in a lot of places, fix
it at least somewhere (and release the resources in such cases),
to avoid that bad things happen.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
spin_lock_irqsave for the HBA lock is called in one function where flag
is local to that function. Another function is called from the first
function where lock has to be released using spin_unlock_irqrestore for
calling task_done of libsas. In the second function also flag is declared
and used. For calling task_done there is no need to enable the irq. So
instead of using spin_lock_irqsave and spin_unlock_irqrestore, spin_lock
and spin_unlock is used now. This also avoids passing the flags across all
the functions where HBA lock is being used. Also removed redundant code.
Reported-by: Jason Seba <jason.seba42@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Viswas G <viswas.g@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pm80xx_get_gsm_dump() was returning "1" in error case
instead of negative error value.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Supports below logging facilities,
Inbound outbound queues dump.
Non fatal dump in case of IO failures.
Fatal dump in case of firmware failure.
[jejb: checkpatch spacing fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Phy profile implementation to support phy settings feature
for motherboard controllers.
[jejb: checkpatch fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[jejb: checkpatch fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Firmware is having an issue. When a single IO request crosses
4G boundary, system will crash. To avoid the issue single sg is
converted into extended sg.
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for indirect data transfer mode in case of SMP request.
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updated pci id table with device, vendor, subdevice and subvendor ids
for 8074, 8076, 8077 SAS/SATA 12G controllers. Added 12G related macros.
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
